Results for “large system simulation” — Page 21

NASA NTRS1993

STE thrust chamber technology: Main injector technology program and nozzle Advanced Development Program (ADP)

The purpose of the STME Main Injector Program was to enhance the technology base for the large-scale main injector-combustor system of oxygen-hydrogen booster engines in the areas of combustion efficiency, chamber heating rates, and combustion stability. The initial task of the Main Injector Program, focused on analysis and theoretical predictions using existing models, was complemented by the design, fabrication, and test at MSFC of a subscale calorimetric, 40,000-pound thrust class, axisymmetric thrust chamber operating at approximately 2,250 psi and a 7:1 expansion ratio. Test results were used to further define combustion stability bounds, combustion efficiency, and heating rates using a large injector scale similar to the Pratt & Whitney (P&W) STME main injector design configuration including the tangential entry swirl coaxial injection elements. The subscale combustion data was used to verify and refine analytical modeling simulation and extend the database range to guide the design of the large-scale system main injector. The subscale injector design incorporated fuel and oxidizer flow area control features which could be varied; this allowed testing of several design points so that the STME conditions could be bracketed. The subscale injector design also incorporated high-reliability and low-cost fabrication techniques such as a one-piece electrical discharged machined (EDMed) interpropellant plate. Both subscale and large-scale injectors incorporated outer row injector elements with scarfed tip features to allow evaluation of reduced heating rates to the combustion chamber.

Source record↗

NASA NTRS2012

Projected Demand and Potential Impacts to the National Airspace System of Autonomous, Electric, On-Demand Small Aircraft

Electric propulsion and autonomy are technology frontiers that offer tremendous potential to achieve low operating costs for small-aircraft. Such technologies enable simple and safe to operate vehicles that could dramatically improve regional transportation accessibility and speed through point-to-point operations. This analysis develops an understanding of the potential traffic volume and National Airspace System (NAS) capacity for small on-demand aircraft operations. Future demand projections use the Transportation Systems Analysis Model (TSAM), a tool suite developed by NASA and the Transportation Laboratory of Virginia Polytechnic Institute. Demand projections from TSAM contain the mode of travel, number of trips and geographic distribution of trips. For this study, the mode of travel can be commercial aircraft, automobile and on-demand aircraft. NASA's Airspace Concept Evaluation System (ACES) is used to assess NAS impact. This simulation takes a schedule that includes all flights: commercial passenger and cargo; conventional General Aviation and on-demand small aircraft, and operates them in the simulated NAS. The results of this analysis projects very large trip numbers for an on-demand air transportation system competitive with automobiles in cost per passenger mile. The significance is this type of air transportation can enhance mobility for communities that currently lack access to commercial air transportation. Another significant finding is that the large numbers of operations can have an impact on the current NAS infrastructure used by commercial airlines and cargo operators, even if on-demand traffic does not use the 28 airports in the Continental U.S. designated as large hubs by the FAA. Some smaller airports will experience greater demand than their current capacity allows and will require upgrading. In addition, in future years as demand grows and vehicle performance improves other non-conventional facilities such as short runways incorporated into shopping mall or transportation hub parking areas could provide additional capacity and convenience.

Smith, Jeremy C.↗

NASA NTRS1992

Unsteady turbomachinery flow simulations on massively parallel architectures

The accurate numerical simulation of unsteady, three-dimensional viscous flow in turbomachines is computationally very intensive, requiring prohibitively large amounts of computer time on current vector supercomputers. In recent years, computer systems based on massively parallel architectures have been developed that offer the promise of meeting the computational power requirements of such large-scale simulations. However, a rethinking of existing algorithms and methodology is required in order to fully harness the computational power of such architectures. In this paper the capabilities of the Connection Machine (CM-2) in predicting unsteady flows in turbomachines are evaluated. The implementation on the CM-2 of an implicit, time-accurate, zonal algorithm for the Navier-Stokes equations in two dimensions is described. Programming issues and modifications made to the original algorithm (developed for vector, pipelined supercomputers) in order to improve performance on the CM-2 are outlined. Algorithm performance is evaluated and compared with a functionally equivalent code for the CRAY-YMP.

Madavan, N. K.↗

NASA NTRS1976

Surface tension propellant control for Viking 75 Orbiter

The paper describes the selection, development and qualification of the surface tension system and includes results of low-g drop tower tests of scale models, 1-g simulation tests of low-g large ullage settling and liquid withdrawal, structural qualification tests, and propellant surface tension/contact angle studies. Subscale testing and analyses were used to evaluate the ability of the system to maintain or recover the desired propellant orientation following possible disturbances during the Viking mission. This effort included drop tower tests to demonstrate that valid wick paths exist for moving any displaced propellant back over the tank outlet. Variations in surface tension resulting from aging, temperature, and lubricant contamination were studied and the effects of surface finish, referee fluid exposure, aging, and lubricant contamination on contact angle were assessed. Results of movies of typical subscale drop tower tests and full scale slosh tests are discussed.

Dowdy, M. W.↗

NASA NTRSDate not supplied

Informing the Space Launch System Booster Separation Initial CFD Run Matrix with Observed Parametric Sensitivity

It currently requires significant computational cost to simulate the flow physics of the booster separation event on the Space Launch System. This comes from the large parametric space in which the event occurs, as pre-separation flight conditions and separated booster core-relative trajectories can vary. Functionally removing the risk of core-booster collision mandates careful assessment of the fluid dynamics in terms of several trajectory parameters. However, simulating the entire trajectory envelope is computationally intractable given the high parametric dimension. In order to reduce the uncertainty in the resulting low-parametric-resolution aerodynamic booster separation database, a data-driven approach was developed to select which breakpoints should be studied by simulations and experiments and which should be relegated to a regression-based interpolation procedure. This technique works by simulating cases where the flow physics are most sensitive to changes in the parameters and leaving the less parametrically sensitive regions for interpolation. The result is a booster separation run matrix whose computational cost is comparable to that of previous database generations but has lower interpolation errors.

SLS↗

NASA NTRSDate not supplied

Informing the Space Launch System Booster Separation Initial CFD Run Matrix with Observed Parametric Sensitivity

It currently requires significant computational cost to simulate the flow physics of the booster separation event on the Space Launch System. This comes from the large parametric space in which the event occurs, as pre-separation flight conditions and separated booster core-relative trajectories can vary. Functionally removing the risk of core-booster collision mandates careful assessment of the fluid dynamics in terms of several trajectory parameters. However, simulating the entire trajectory envelope is computationally intractable given the high parametric dimension. In order to reduce the uncertainty in the resulting low-parametric-resolution aerodynamic booster separation database, a data-driven approach was developed to select which breakpoints should be studied by simulations and experiments and which should be relegated to a regression-based interpolation procedure. This technique works by simulating cases where the flow physics are most sensitive to changes in the parameters and leaving the less parametrically sensitive regions for interpolation. The result is a booster separation run matrix whose computational cost is comparable to that of previous database generations but has lower interpolation errors.

SLS↗

NASA NTRS1975

Motion-base simulator study of control of an externally blown flap STOL transport aircraft after failure of an outboard engine during landing approach

A moving-base simulator investigation of the problems of recovery and landing of a STOL aircraft after failure of an outboard engine during final approach was made. The approaches were made at 75 knots along a 6 deg glide slope. The engine was failed at low altitude and the option to go around was not allowed. The aircraft was simulated with each of three control systems, and it had four high-bypass-ratio fan-jet engines exhausting against large triple-slotted wing flaps to produce additional lift. A virtual-image out-the-window television display of a simulated STOL airport was operating during part of the investigation. Also, a simple heads-up flight director display superimposed on the airport landing scene was used by the pilots to make some of the recoveries following an engine failure. The results of the study indicated that the variation in visual cues and/or motion cues had little effect on the outcome of a recovery, but they did have some effect on the pilot's response and control patterns.

Middleton, D. B.↗

NASA NTRS2020

Adaptive Stress Testing: Finding Likely Failure Events with Reinforcement Learning

Finding the most likely path to a set of failure states is important to the analysis of safety-critical systems that operate over a sequence of time steps, such as aircraft collision avoidance systems and autonomous cars. In many applications such as autonomous driving, failures cannot be completely eliminated due to the complex stochastic environment in which the system operates.As a result, safety validation is not only concerned about whether a failure can occur, but also discovering which failures are most likely to occur. This article presents adaptive stress testing (AST), a framework for finding the most likely path to a failure event in simulation. We consider a general black box setting for partially observable and continuous-valued systems operating in an environment with stochastic disturbances. We formulate the problem as a Markov decision process and use reinforcement learning to optimize it. The approach is simulation-based and does not require internal knowledge of the system, making it suitable for black-box testing of large systems. We present different formulations depending on whether the state is fully observable or partially observable. In the latter case, we present a modified Monte Carlo tree search algorithm that only requires access to the pseudorandom number generator of the simulator to overcome partial observability. We also present an extension of the framework, called differential adaptive stress testing (DAST), that can find failures that occur in one system but not in another. This type of differential analysis is useful in applications such as regression testing, where we are concerned with finding areas of relative weakness compared to a baseline. We demonstrate the effectiveness of the approach on an aircraft collision avoidance application, where a prototype aircraft collision avoidance system is stress tested to find the most likely scenarios of near mid-air collision.

Verification and Validation↗

NASA NTRS1991

Numerical propulsion system simulation

The cost of implementing new technology in aerospace propulsion systems is becoming prohibitively expensive. One of the major contributors to the high cost is the need to perform many large scale system tests. Extensive testing is used to capture the complex interactions among the multiple disciplines and the multiple components inherent in complex systems. The objective of the Numerical Propulsion System Simulation (NPSS) is to provide insight into these complex interactions through computational simulations. This will allow for comprehensive evaluation of new concepts early in the design phase before a commitment to hardware is made. It will also allow for rapid assessment of field-related problems, particularly in cases where operational problems were encountered during conditions that would be difficult to simulate experimentally. The tremendous progress taking place in computational engineering and the rapid increase in computing power expected through parallel processing make this concept feasible within the near future. However it is critical that the framework for such simulations be put in place now to serve as a focal point for the continued developments in computational engineering and computing hardware and software. The NPSS concept which is described below will provide that framework.

R.W. Claus↗

NASA NTRS1990

Numerical propulsion system simulation

The cost of implementing new technology in aerospace propulsion systems is becoming prohibitively expensive. One of the major contributors to the high cost is the need to perform many large scale system tests. Extensive testing is used to capture the complex interactions among the multiple disciplines and the multiple components inherent in complex systems. The objective of the Numerical Propulsion System Simulation (NPSS) is to provide insight into these complex interactions through computational simulations. This will allow for comprehensive evaluation of new concepts early in the design phase before a commitment to hardware is made. It will also allow for rapid assessment of field-related problems, particularly in cases where operational problems were encountered during conditions that would be difficult to simulate experimentally. The tremendous progress taking place in computational engineering and the rapid increase in computing power expected through parallel processing make this concept feasible within the near future. However it is critical that the framework for such simulations be put in place now to serve as a focal point for the continued developments in computational engineering and computing hardware and software. The NPSS concept which is described will provide that framework.

Lytle, John K.↗

NASA NTRS1971

Integration methods where force is obtained from the smoothed gravitational field.

Discussion of the possibilities to study the dynamics of collisionless stellar systems by condensing the large number of stars that such systems may contain into a smaller number of superparticles and using numerical or computer models to perform computer experiments simulating Vlasov phenomena by following the simultaneous motion of a large number of superparticles. A computer model for disks of stars and a two-dimensional rod model are considered.

Hohl, F.↗

NASA NTRSDate not supplied

An Application of Flexible Multibody Simulations to Space Launch Systems Liftoff Pad Separation and Umbilical Disconnect

A flexible multibody dynamics approach is applied to the Space Launch System (SLS) liftoff Coupled Loads Analysis (CLA), enabling the inclusion of a large array of component nonlinearities with extreme computational efficiency. The nonlinearities include the cryogenic induced preloads due to the large rotations of the aft struts connecting the Core Stage (CS) to the boosters, the contact/separation and potential re-contact at the booster aft skirt to Mobile Launcher(ML) interface, contact/separation and potential re-contact at the ML/extensible columns interfaces, secondary disconnect of the CS umbilicals including the LOX and LH2 Tail Service Mast Umbilicals (TSMUs), and the disconnect of the upper stage umbilical, the Interim Cryogenic Propulsion Stage Umbilical (ICPSU). The ICPSU disconnect involves algorithms simulating the winch motors reeling lanyard ropes, the nonlinear modeling of ropes and hoses, the disconnect and capture of multiple umbilical ground plates by catch-nets (geometrically nonlinear models), and the large rotations of the ML gantry in order to track clearances between the lifting SLS vehicle and umbilicals rotating out of the way. The flexible multibody dynamics framework utilized for these simulations provided a systematic and efficient framework for adding complex nonlinearities at the system level which would have otherwise not been possible in standard CLAs or would have to be treated by separate local analyses thereby not accounting for the coupled system behavior.

Application↗

NASA NTRS1975

Simulation of on-orbit maintenance cycle for LST

A maintenance simulation model of the Large Space Telescope has been developed to assess the operational cost sensitivity to system configuration options. The model lends itself to equipment-level selections for various subsystem alternatives. Maintenance decisions include considerations for LST spacecraft on-orbit service or retrieval. Tradeoffs are identified in terms of on-orbit maintenance for specific design concepts, with Space Shuttle revisit costs balanced against retrieval and ground-facility operations. Simulation output is in the form of computer plots of cost, availability, time to first maintenance, and a cost-effective Shuttle revisit frequency.

Donnelly, J. A.↗

NASA NTRSDate not supplied

Enhanced Simulation Techniques in Predicting Sonic Boom Loudness Using CFD

This paper outlines advancements in predicting sonic boom loudness within the Launch, Ascent, and Vehicle Aerodynamics (LAVA) computational framework. Traditionally, a two step process consisting of a steady state computational fluid dynamics problem for near-field analysis and a far-field propagation solver for calculation of loudness metrics has been used. Improvements to this process made in this work include utilizing a high-order space marching method for mid-field computations, developing a novel output-based mesh adaptation method targeting error in near-field pressure sig-natures, and developing a robust scripting system using curvilinear grids to increase robustness and simplify the process of running large databases of simulation cases. These advancements are detailed and applied to the simulation of the X-59, presenting comparative cost and timing analyses between the prior two step workflow and the current three step procedure. We achieve increased accuracy and robustness for loudness predictions with at least a50%computational cost reduction.

CST↗

NASA NTRS1981

Pitfalls and guidelines for the numerical evaluation of moderate-order system frequency response

The design and evaluation of a feedback control system via frequency response methods relies heavily upon numerical methods. In application, one can usually develop low order simulation models which for the most part are devoid of numerical problems. However, when complex feedback interactions, for example, between instrument control systems and their flexible mounting structure, must be evaluated, simulation models become moderate to large order and numerical problems become common. A large body of relevant numerical error analysis literature is summarized in a large language understandable to nonspecialists. The intent is to provide engineers using simulation models with an engineering feel for potential numerical problems without getting intertwined in the complexities of the associated mathematical theory. Guidelines are also provided by suggesting alternate state of the art methods which have good numerical evaluation characteristics.

Frisch, H. P.↗

NASA NTRS1983

Space environmental effects on materials

Research efforts at NASA-Langley to characterize the durability of composite materials which are candidates or use as components on various space hardware systems are reviewed. The material applications include large space structures, antennas, cables, thermal control coatings, solar reflectors, and satellite power systems. Simulation facilities have been built to study radiation effects on polymer matrix composites, and the dimensional stability of the matrix composites and tension stabilized.

Tenny, D. R.↗

NASA NTRS1982

Space environmental effects on materials

Research efforts at NASA-Langley to characterize the durability of composite materials which are candidates for use as components on various space hardware systems are reviewed. The material applications include large space structures, antennas, cables, thermal control coatings, solar reflectors, and satellite power systems. Simulation facilities have been built to study radiation effects on polymer matrix composites, and the dimensional stability of the matrix composites and tension stabilized cables. Numerical models are being developed for radiation effects on the mechanical, physical, and optical properties. Additionally, chemical and microstructural analyses are performed to identify damage mechanisms and the limits of effectiveness of accelerating life tests. It is noted that no residual strength reduction has been detected in polymer films after dosages of 5 billion rads of electron radiation.

Tenney, D. R.↗

NASA NTRS1986

Simulator Tests Controller Performance

Compact servosystem applies simulated dynamic loads, enabling realistic appraisal of motor and its control system without inconvenience of attaching real load. System simulates moments of inertia, rotational vibrations, changing load torques, and other characteristics of large or complex loads, without loads themselves and without awkwardness (and inaccuracy) of gravity-compensating devices used with such loads.

Lembeck, M. F.↗