Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Experimental evaluation of shear modulus scaling of dynamic strength at extreme pressures

Recent progress in the development of dynamic strength experimental platforms is allowing for unprecedented insight into the assumptions used to construct constitutive models operating in extreme conditions. In this work, we make a quantitative assessment of how tantalum strength scales with its shear modulus to pressures of hundreds of gigapascals through a cross-platform examination of three dynamic strength experiments. Specifically, we make use of Split–Hopkinson pressure bar and Richtmyer–Meshkov instability experiments to assess the low-pressure strain and strain rate dependence. Concurrent examination of magnetically driven ramp-release experiments up to pressures of 350GPa allows us to examine the pressure dependence. In this work, using a modern description of the shear modulus, validated against both ab initio theory and experimental measurements, we then assess how the experimentally measured pressure dependence scales with shear modulus. Furthermore, we find that the common assumption of scaling strength linearly with the shear modulus is too soft at high pressures and offer discussion as to how descriptions of slip mediated plasticity could result in an alternative scaling that is consistent with the data.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS2006

Polyimides From a-BPDA and Aromatic Diamines

Polymers having low color and a favorable combination of other properties, including high glass-transition temperature (Tg) and high mechanical properties (strength, tensile modulus, and toughness) will find use in a variety of terrestrial and space applications. Some of the space applications will be in thin films used as membranes on antennas, solar concentrators, coatings on second-surface mirrors, solar sails, sunshades, thermal and optical coatings, and multi-layer thermal insulation blankets. Depending upon the application, the film will be required to exhibit a unique combination of such properties as resistance to degradation by ultraviolet light, visible light, and electrons; low color and/or low solar absorptivity; resistance to tearing and/or wrinkling during packaging and deployment; and high mechanical properties (e.g. high strength, stiffness, and toughness).

Hergenrother, Paul M.↗
DOE OSTI2021

Machine learning elastic constants of multi-component alloys

The present manuscript explores application of machine learning methods for determining elastic constants and other derived mechanical properties of multi-component alloys. Here, a number of machine learning models, including linear regression, neural network and random forest based models, are trained and tested on a dataset of binary alloys generated using density functional theory (DFT) calculations and spanning over a large number of elemental species in the periodic table. Starting with a wide range of simple and easily accessible compositionally-averaged elemental features, a correlation-based feature selection strategy was used to systematically down-select a set of most relevant features towards the prediction of the elasticity tensor components. The true predictive performance and the associated uncertainties of the models were established by testing on unseen data and bootstrapping, respectively. A single and pair-wise feature partial dependence analysis was performed to visualize the average property trends in the multi-dimensional feature space in order to further understand the achieved predictive performance. The utility of the trained model is further demonstrated by obtaining sufficiently accurate yet highly efficient approximations for bulk modulus, Young’s modulus, shear modulus and Poisson’s ratio for alloys beyond the binary space (i.e., two-component alloys) on which the model was originally trained. More importantly, we test and validate the predictive performance of the developed model directly against the experimentally measured elastic constants of technologically relevant multi-component alloys (such as, Ni- and Ti-based alloys). Finally, utility of such a data-enabled route is demonstrated by predicting the possible range of various elastic properties for vast composition space available within the five component Ni-Cr-Fe-Mo-W alloy system in a high-throughput manner.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Experimental Assessment of Elastic Modulus vs. Relative Density for Stretch- and Bend-Dominated Lattices

This project was designed to study the possibility of using structural properties of lattices to replicate the material properties of certain hard to manufacture designs and use topology optimization to determine the lattice type and density required to mimic these properties. The integration of additively manufactured lattice structures with topology optimization highlights the need for well characterized mechanical properties and uncertainty analyses to insure these optimized structures respond as predicted. Stereolithographically printed octet and rhombic dodecahedron lattices were manufactured at 10%, 25% and 65% density by volume. As a separate task, yet integrated into this work, finite element analysis (FEA) was used to predict the printed lattice’s mechanical properties, which were then compared to our experimental results. After comparing FEA and experimentallymeasured elastic moduli, it was determined that the FEA provides highly reliable predictions for the modulus of these printed lattice structures. These lattices also exhibited greater tensile stiffness than that of the solid material demonstrating the flexibility that lattices provide to designing parts with designer structural properties. The accurate printing and reliable modeling of these lattices will enable topology optimization of complex parts from well-characterized rhombic dodecahedron and octet lattice structures of varying densities.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Highly Deformable Rigid Glassy Conjugated Polymeric Thin Films

Wearable devices benefit from the use of stretchable conjugated polymers (CPs). Traditionally, the design of stretchable CPs is based on the assumption that a low elastic modulus (E) is crucial for achieving high stretchability. However, this research, which analyzes the mechanical properties of 65 CP thin films, challenges this notion. It is discovered that softness alone does not determine stretchability; rather, it is the degree of entanglement that is critical. This means that rigid CPs can also exhibit high stretchability, contradicting conventional wisdom. To inverstigate further, the mechanical behavior, electrical properties, and deformation mechanism of two model CPs: a glassy poly(3-butylthiophene-2,5-diyl) (P3BT) with an E of 2.2 GPa and a viscoelastic poly(3-octylthiophene-2,5-diyl) (P3OT) with an E of 86 MPa, are studied. Ex situ transmission X-ray scattering and polarized UV–vis spectroscopy revealed that only the initial strain (i.e., <20%) exhibits different chain alignment mechanisms between two polymers, while both rigid and soft P3ATs showed similarly behavior at larger strains. In conclusion, by challenging the conventional design metric of low E for high stretchability and highlighting the importance of entanglement, it is hoped to broaden the range of CPs available for use in wearable devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Synthesis and characterization of biobased copolyesters based on pentanediol: (2) Poly(pentylene adipate–co–terephthalate)

Traditionally, most flexible food packaging is made of linear low-density polyethylene (LLDPE) which cannot easily be recycled, nor will it degrade in a reasonable timescale. In this work, a biobased biodegradable polyester alternative was investigated as a possible replacement for LLDPE. High molecular weight poly (pentylene adipate-co-terephthalate) with a 40/60 adipic acid/terephthalic acid mole ratio was synthesized using direct esterification and polycondensation. Glycerol and hexane-1,2,5,6-tetrol were added as branching agents to better match the structure of the LLDPE which in turn might help the ability of these materials in film-blowing. Thermal, mechanical, and rheological properties of the copolyesters were thoroughly investigated. All copolyesters had a weight-average molecular weight of over 140,000 g/mol, which is necessary for proper rheology, and were thermally stable up to 350°C. Here, the addition of branching agents led to a slight decrease in crystallinity, d-spacing, melting temperature, enthalpy of melting, stress at break, and elongation at break. However, an increase in Young's modulus and complex viscosity at high frequency were observed compared to PPeAT60 without branching agent added. Although the improved crystallinity and mechanical properties of the copolyesters made them viable for film-blowing, the slow crystallization rate creates a major challenge.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Supramolecular Arene‐Perfluoroarene Assembly Enhances Photoiniferter Polymerization Kinetics

Ultra-high-molecular-weight (UHMW, >106 Da) polymers have unique thermomechanical properties due to their large number of physical entanglements. Producing UHMW styrenic polymers is challenging because of their prohibitively slow homopolymerization kinetics. In this report, we show that alternating photoiniferter copolymerization between methoxy-functionalized styrenic monomers and pentafluorostyrene can circumvent this limitation under conditions where arene–perfluoroarene (AP) interactions contribute to favorable monomer association and accelerate copolymerization. Increasing methoxy substitution on the styrene arene ring leads to pronounced rate enhancements that correlate with electronic complementarity between the styrenic comonomers. Density functional theory calculations reveal increasingly favorable AP interaction energies across the series, consistent with monomer association contributing to faster propagation. The result is up to 2000% enhancement in propagation rate in copolymerizations compared to styrene homopolymerization. Despite these rate enhancements, the resulting materials retain broadly similar glass-transition temperatures and network-like thermomechanical behavior, with only modest softening across the series. Here, we then leverage the approach to produce UHMW trialkoxystyrene copolymers bearing sterically encumbered pendants, which are ultrasoft (Young's modulus of 8 kPa) and highly extensible (560%). These results establish that designed supramolecular association between styrenics is a powerful tool for controlling reactivity in radical polymerization and generating otherwise difficult-to-obtain materials.

Marquez, Joshua D. [University of Florida, Gainesv↗
NASA NTRS2014

The Effect of Indenter Ball Radius on the Static Load Capacity of the Superelastic 60NiTi for Rolling Element Bearings

Static load capacity is a critical design parameter for rolling element bearings used in space mechanisms because of the potential for Brinell (surface dent) damage due to shock and vibration loading events during rocket launch. Brinell damage to bearing raceways can lead to torque variations (noise) and reduced bearing life. The growing use of ceramic rolling elements with high stiffness in hybrid bearings exacerbates the situation. A new family of hard yet resilient materials based upon nickel-titanium is emerging to address such bearing challenges. 60NiTi is a superelastic material that simultaneously exhibits high hardness and a relatively low elastic modulus (approx. 100 GPa) and has been shown to endure higher indentation loads than conventional and high performance steel. Indentation load capacity has been reported for relatively large (12.7 mm diameter) ceramic (Si3N4) indenter balls pressed against flat plates of 60NiTi. In order to develop damage load threshold criteria applicable to a wide range of bearing designs and sizes, the effects of indenter ball radius and the accuracy of interpolation of the Hertz contact stress relations for 60NiTi must be ascertained. In this paper, results of indentation tests involving ceramic balls ranging from 6.4 to 12.7 mm in diameter and highly polished 60NiTi flat plates are presented. When the resulting dent depth data for all the indenter ball sizes are normalized using the Hertz equations, the data (dent depth versus stress) are comparable. Thus when designing bearings made from 60NiTi, the Hertz stress relations can be applied with relative confidence over a range of rolling element sizes and internal geometries.

bearings↗
NASA NTRS2014

The Effect of Indenter Ball Radius on the Static Load Capacity of the Superelastic 60NiTi for Rolling Element Bearings

Static load capacity is a critical design parameter for rolling element bearings used in space mechanisms because of the potential for Brinell (surface dent) damage due to shock and vibration loading events during rocket launch. Brinell damage to bearing raceways can lead to torque variations (noise) and reduced bearing life. The growing use of ceramic rolling elements with high stiffness in hybrid bearings exacerbates the situation. A new family of hard yet resilient materials based upon nickel-titanium is emerging to address such bearing challenges. 60NiTi is a superelastic material that simultaneously exhibits high hardness and a relatively low elastic modulus (approx. 100 GigaPascals) and has been shown to endure higher indentation loads than conventional and high performance steel. Indentation load capacity has been reported for relatively large (12.7 millimeters diameter) ceramic (Si3N4) indenter balls pressed against flat plates of 60NiTi. In order to develop damage load threshold criteria applicable to a wide range of bearing designs and sizes, the effects of indenter ball radius and the accuracy of interpolation of the Hertz contact stress relations for 60NiTi must be ascertained. In this paper, results of indentation tests involving ceramic balls ranging from 6.4 to 12.7 mm in diameter and highly polished 60NiTi flat plates are presented. When the resulting dent depth data for all the indenter ball sizes are normalized using the Hertz equations, the data (dent depth versus stress) are comparable. Thus when designing bearings made from 60NiTi, the Hertz stress relations can be applied with relative confidence over a range of rolling element sizes and internal geometries.

materials↗
DOE OSTI2022

HFTS-1 Natural Joint Data and Engineering Summary

This report provides an analysis of engineering and geologic data collected from the Hydraulic Fracturing Test Site #1 (HTSF-1) project in the southern Midland Basin, Reagan County, Texas. The site is being studied as part of the Science-informed Machine Learning for Accelerating Real-Time Decisions in Subsurface Applications (SMART) Initiative at the National Energy Technology Laboratory (NETL). The data collected is intended to provide a basis of understanding of the site and to construct simulation models. This report provides a summary analysis of the engineering and geologic data collected from the project to provide a basis of understanding of the site and to construct simulation models. The report examines various possible correlations in engineering properties based on natural fracture data from the program, which consisted of 11 horizontal wells, one vertical well, and one slant well. The horizontal wells are in two horizons: 1) Upper and 2) Middle Wolfcamp formations. Program data include: fracture frequency and fracture orientation data from four core runs in a slant well; fracture spacing and orientation from a vertical pilot well; laboratory triaxial testing and mineralogical determinations; and porosity results from magnetic resonance analyses from various wells, together with observations based on the data collection. In addition, available references were reviewed on the site for additional insights. As the focus of the report is on the natural system, hydraulic fracture data from the site were not examined in detail in this report. Data variability is the chief observation in examination of the database. Fracture frequency in the slant well can range from sections with values as high as five fractures per ft to sections up to 100+ ft in length with no natural observed fractures. Fracture spacing across is typically less than 10 ft, but can range up to hundreds of feet. Apparent fracturing shows the trends in two predominate orientations, E-SW and WNW-ESE, but minor variations exist. The rock units vary across the site from siliceous mudstones to calcareous mudstones, showing a general layering with depth. The laboratory properties such as strength and modulus show no apparent trend with depth, but appear to correlate with rock mineralogy with high strength and modulus values where calcium content is high. In addition, an attempt to examine variability and mineralogy on a larger scale was made using a color-coded system based on gamma ray measurements. A staged colored approach was adopted, presuming that lower gamma ray values indicate higher value of calcium content (blue scale) and that higher gamma ray values indicate higher clay mineral content (orange scale). As provided in report appendices, the system correlated well with visual examination of the slant core and the petrofabric analyses of the vertical pilot well. The results showed large variability in mineral content along the horizontal plane across the site. The change in mineral content was also rapid, on a scale less than that of the average hydraulic fracture stage length of about 180 ft.

42 ENGINEERING↗
DOE OSTI2020

Stabilizing Dendritic Electrodeposition by Limiting Spatial Dimensions in Nanostructured Electrolytes.

The tendency of metals to form uncontrolled dendritic morphologies during electrodeposition hinders the development of safe and reliable metal batteries. Multiphase nanostructured electrolytes can suppress dendritic growth if the mechanical modulus of the electrolyte is high relative to that of the metal or if the conducting channels are confined to nanoscale dimensions. Direct visualization and analysis of electrodeposition within polymeric nanostructures elucidates the structure-property relationships and mechanisms underlying the suppression of dendrite growth. Here, we fabricate precisely structured multiphase films composed of nanochannels of a polymeric electrolyte in a background of nonconductive polymer on top of coplanar electrodes. The devices enable imaging and analysis of electrodeposition behavior as a function of channel width by scanning electron microscopy. We find that electrodeposition is confined to individual conductive channels and that radial propagation of the dendritic morphology is suppressed in channels for which the width is smaller than the characteristic dendritic nucleation size.

Sharon, Daniel↗
DOE OSTI2021

Dynamic behavior of chemically tunable mechano-responsive hydrogels

Here, using theory and simulation, we model the mechanical behavior of gels that encompass loops and dangling chain ends. If the loops remain folded and dangling ends are chemically inert, then these topological features just serve as defects. If, however, the loops unfold to expose the hidden (“cryptic”) binding sites and the ends of the dangling chains are reactive, these moieties can form bonds that improve the gel's mechanical properties. For gels with a lower critical solubility temperature (LCST), we systematically switch on the possible unfolding and binding events. To quantify the resulting effects, we derive equations for the gel's equilibrium and dynamic elastic moduli. We also use a finite element approach to simulate the gel's response to deformation and validate the analytic calculations. Herein, we show that the equilibrium moduli are highly sensitive to the presence of unfolding and binding transitions. The dynamical moduli are sensitive not only to these structural changes, but also to the frequency of deformation. For example, when reactive ends bind to exposed cryptic sites at T = 29 °C and relatively high frequency, the storage shear modulus is 119% greater than the corresponding equilibrium value, while the storage Young's modulus is 109% greater than at equilibrium. These findings provide guidelines for tuning the chemical reactivity of loops and dangling ends and the frequency of deformation to tailor the mechano-responsive behavior of polymer networks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Grayscale Digital Light Processing Gradient Printing for Stress Concentration Reduction and Material Toughness Enhancement

Avoiding stress concentrations is essential to achieve robust parts since failure tends to originate at such concentrations. With recent advances in multimaterial additive manufacturing, it is possible to alter the stress (or strain) distribution by adjusting the material properties in selected locations. Here, we investigate the use of grayscale digital light processing (g-DLP) 3D printing to create modulus gradients around areas of high stress. These gradients prevent failure by redistributing high stresses (or strains) to the neighboring material. The improved material distributions are calculated using finite element analysis. The much-enhanced properties are demonstrated experimentally for thin plates with circular, triangular, and elliptical holes. In conclusion, this work suggests that multimaterial additive manufacturing techniques like g-DLP printing provide a unique opportunity to create tougher engineering materials and parts.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Shear failure and impact resistance in graphite fiber laminates

The multispan beam (MSB) test was evaluated as a predictor of damage resistance and damage tolerance in quasi-isotropic graphite laminates. Materials studied were five commercial prepreg system using high-strain and intermediate-modulus carbon fibers, as well as an amorphous thermoplastic system. Failure loads and displacements in the MSB tests showed little rate dependence. Values of compressive strength after a standard low-velocity impact correlated fairly well with the MSB results.

Srinivasan, Krishna↗
NASA NTRS2015

Lightweight, Wearable, Metal Rubber Sensor

For autonomous health monitoring. NanoSonic, Inc., has developed comfortable garments with multiple integrated sensors designed to monitor astronaut health throughout long-duration space missions. The combined high electrical conductivity, low mechanical modulus, and environmental robustness of the sensors make them an effective, lightweight, and comfortable alternative to conventional use of metal wiring and cabling.

Hill, Andrea↗
NASA NTRS1983

Mechanical and spectroscopic properties of metal-containing polyimides

The incorporation of specific metal ions into polyimides is described. Detailed studies have included various compounds of copper, lithium, and palladium as dopants. Addition of the metal during polymerization or after formation of the polyamic acid precedes the thermal imidization step. With many dianhydride-diamine-dopant combinations high quality variously colored films are produced. Many metal doped films exhibit (1) improved high temperature adhesive properties, (2) increased electrical conductivity, (3) excellent thermal stability, (4) improved acid/base resistance, (5) increased modulus in flexible films and (6) excellent high temperature tensile strength. X-ray photo-electron spectroscopic study of these films suggests that many of the additives undergo chemical modification during thermal imidization. Palladium dopants appear to be partially reduced to the metallic state, while lithium and copper dopants are probably converted to their oxides. Ion etching experiments with Auger electron spectroscopy monitoring are discussed.

Taylor, L. T.↗
NASA NTRS1984

Mechanical and spectroscopic properties of metal containing polyimides

The incorporation of specific metal ions into polyimides is described. Detailed studies have included various compounds of copper, lithium, and palladium as dopants. Addition of the metal during polymermzation or after formation of the polyamic acid precedes the thermal imidization step. With many dianhydride-diamine-dopant combinations high quality variously colored films are produced. Many metal doped films exhibit (1) improved high temperature adhesive properties, (2) increased electrical conductivity, (3) excellent thermal stability, (4) improved acid/base resistance, (5) increased modulus in flexible films and (6) excellent high temperature tensile strength. X-ray photo-electron spectroscopic study of these films suggests that many of the additives undergo chemical modification during thermal imidization. Palladium dopants appear to be partially reduced to the metallic state, while lithium and copper dopants are probably converted to their oxides. Ion etching experiments with Auger electron spectroscopy monitoring are discussed.

Taylor, L. T.↗
NASA NTRS1987

Design study of advanced model support systems for the National Transonic Facility (NTF)

It has long been recognized that the sting (or support system) is a very critical part of the model system. The designer is frequently faced with the tradeoff of minimizing sting size, thereby compromising facility and model safety, against a larger sting and the subsequent problems of sting interference effects. In the NASA Langley Research Center National Transonic Facility (NTF), this problem is accentuated by the severe environment of high pressure/low temperature, designed into the facility to provide the desired high Reynolds number. Compromises in the configuration geometry and/or limiting the test envelope are therefore contrary to the purposes and goals of the NTF and are unacceptable. The results of an investigation aimed at improvements of 25% in both strength and Young's modulus of elasticity as compared to high strength cryogenically acceptable steels currently being used are presented. Various materials or combinations of materials were studied along with different design approaches. Design concepts were developed which included conventional material stings, advanced composites, and hybrid configurations. Candidate configurations are recommended.

Source record↗