SEARCH · Engineering Papers

Results for “fusion reactor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Mechanical characterization of fine-grain dispersion-strengthened tungsten as a plasma facing material

Field-Assisted Sintering Technology (FAST) was used to produce fine-grained, dispersion-strengthened tungsten (W) materials. Investigated materials 4138, 4353, and 4355 composed of 3 wt% ZrC sintered at 1800 °C, 5 wt% ZrC sintered at 1800 °C, and 3 wt% ZrC sintered at 2000 °C, respectively. They were compared against ITER-grade W. A series of mechanical and thermal property testing and microstructure studies were conducted to study them as a potential plasma facing material (PFM) for fusion reactors. Hardness testing showed that manufacturing conditions substantially altered hardness. Material 4355 had an average HV10 value of 497.2 ± 16.8, slightly higher than ITER-grade at 378.5 ± 40.3. However, material 4353 was substantially higher with an HV10 value of 738.9 ± 31.7 over the investigated temperature range. Electron Backscatter Diffraction (EBSD) analysis showed that FAST produced substantially smaller grains than the hot-rolled ITER-grade W material, offering notable control over grain size. Materials 4353 and 4355 had grain sizes of 0.44 ± 0.20 µm and 3.67 ± 0.89 µm, respectively, whereas ITER-grade 27.14 ± 19.76 µm at room temperature. The fine grain structures showed no net coarsening after 1 hr. anneals up to 1800 °C, several hundred degrees above the 1100 – 1500 °C recrystallization range reported for conventional W. Inverse application of the Zener pinning relationship to the measured grain sizes indicates that these two FAST sintering conditions produce markedly different effective dispersoid populations, with effective particle diameters of approximately 90 nm at a peak sintering temperature of 1800 °C and approximately 460 nm at 2000 °C, respectively. This result demonstrates that the FAST thermal condition itself, and not the nominal ZrC content alone, governs the pinning effectiveness of the dispersion. Thermal diffusivity measurements support this finding independently. Materials of identical composition sintered at different temperatures differ by approximately 19% in measured thermal diffusivity with statistically indistinguishable density, while materials of different composition and sintering temperature converge to within approximately 2%. At a representative divertor heat flux of 10 MW/m², the lower thermal conductivity of the fine-grained materials corresponds to approximately 28 to 33 °C per millimeter of armor thickness relative to ITER-grade W, traded against a substantially larger margin to recrystallization-driven degradation. While high temperature tensile testing revealed likely contamination that motivates refinement of the manufacturing process, FAST-produced, fine-grained, dispersion-strengthened W offers process-controlled microstructural stability well above the operating temperatures of conventional W and supports its continued development as a PFM for economically viable commercial fusion power.

Parker, Gabe [ORNL] (ORCID:0000000190394100)↗

DOE OSTI2024

Investigation of Materials for Radio Frequency Antenna Plasma Facing Components

Here, the interaction of radio frequency (RF) sheaths with fusion reactor relevant materials (e.g., tungsten and titanium diboride) is being studied on the RF Plasma Interaction Experiment (RF PIE). The RF PIE consists of an electron cyclotron resonance (ECR) plasma source (2.45 GHz, 5 kW) with a biased and heated RF electrode that is used to simulate antenna surfaces in contact with the edge plasma. Helium plasmas (density of ~1e18/m 3 , electron temperature of 4–5 eV) are being used to explore sheath formation on material surfaces with biases up to 500 V. The erosion of a tungsten surface is being studied spectroscopically using a mirror-linked 1 m Czerny-Turner UV imaging spectrometer with a spectral resolution of 0.012 nm for measuring plasma emission in and near the sheath. Tungsten line emission intensity is higher for RF versus dc biasing for similar plasma conditions and average ion energy. RF biasing causes a broadening of the ion energy distribution function (IEDF) due to the RF sheath, as determined from the hPIC2 code, and results in enhanced sputtering. Calculations of the expected sputtering yield for dc and RF biasing are consistent with experimental observations of changes in the 400.9 nm tungsten line emission intensity as a function of ion energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Perspectives and challenges of ultra-high temperature ceramics for fusion plasma-facing applications

Ultra-high temperature ceramics (UHTCs) offer several potential advantages as plasma-facing components (PFCs) in fusion reactors due to their extreme melting points, tailorable thermal conductivity, and attractive unirradiated mechanical properties including fracture toughness comparable or superior to tungsten. Here, recent developments and material properties of UHTCs are briefly reviewed, along with an overview of limited studies on their responses to neutron irradiation and an evaluation of plasma-surface interactions. Five key research pathways, primarily focused on irradiation effects, for advancing UHTCs in PFC applications are discussed: (1) assessing irradiation effects on the coupled thermal–mechanical performance (2) addressing the lack of studies on irradiation, plasma-surface interactions, and their synergistic effects; (3) investigating high-temperature (>1000 °C) neutron irradiation effects critical for PFC performance; (4) optimizing multi-component UHTC compositions or composites to improve thermal or mechanical properties; (5) enhancing radiation resistance to mitigate microcracking and void swelling through strategies such as increasing sink strength by reducing grain size, introducing fine particles, and leveraging complex concentrated alloy concepts.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Mesh refinement for anisotropic diffusion in magnetized plasmas

Highly accurate simulation of plasma transport is needed to drive the successful design and operation of magnetically confined fusion reactors. Unfortunately, the extreme anisotropy present in magnetized plasmas results in thin boundary layers that are expensive to resolve. Here, this work investigates how various mesh refinement strategies might reduce that expense to allow for more efficient simulation by comparing standard variable refinement approaches that use a field quantity to an adaptive approach that uses an error estimator. It is first verified that higher order discretization only realizes the proper rate of convergence once the mesh resolves the thin boundary layer, therefore motivating the focusing of refinement on the boundary layer. For three two-dimensional test cases that contain characteristic features of tokamak magnetic fields, an exponential refinement strategy based on the magnetic flux function, which is the standard refinement approach in the field, is compared to an adaptive strategy utilizing the established Zienwiekicz and Zhu error estimator. The adaptive mesh refinement strategy consistently achieves the same accuracy using orders of magnitude less degrees of freedom than either exponential or uniform refinement. This result makes the adaptive refinement strategy more efficient than the exponential refinement strategy while also being more generalizable to problems with complex magnetic geometries. Scaling laws are derived that quantify the improvement in cost of the adaptive refinement strategy over other refinement approaches in 2D and 3D.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2022

Liquid lithium as divertor material to mitigate severe damage of nearby components during plasma transients

The successful operation of thermonuclear fusion reactors such as ITER, DEMO, and future commercial plants is mainly determined by the optimum choice of materials for various components. The objective of this work is to accurately and comprehensively simulate the entire device in 3D to predict pros and cons of various materials, e.g., liquid lithium in comparison to tungsten and carbon to predict future ITER-like and DEMO divertor performances. We used our comprehensive HEIGHTS simulation package to investigate ITER-like components response during transient events in exact 3D geometry. Starting from the lost hot core plasma particles through SOL, deposition on the divertor surface, and the generation of secondary plasma of divertor materials. Our simulations predicted significant reduction in the heat loading and damage to the divertor nearby and internal components in the case when lithium is used on the divertor plates. While if tungsten or carbon are used on the divertor plate, significant melting areas and vaporization spots can occur (less for carbon) on the reflector, dome, and stainless steel tubes, and even parts of the first walls can melt due to the high radiation power of the secondary divertor plasma. Lithium photon radiation deposition into the divertor and nearby surfaces was decreased by two orders of magnitude compared to tungsten and by one order of magnitude compared to carbon. This analysis showed that using liquid lithium for ITER-like surfaces and future DEMO can lead to significant enhancement in components lifetime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Scenario optimization for the tokamak ramp-down phase in RAPTOR: Part B. safe termination of DEMO plasmas

An optimized plasma current ramp-down strategy is critical for safe and fast termination of plasma discharges in a tokamak demonstration fusion reactor (DEMO), both in planned and emergency scenarios, avoiding plasma disruptions and excessive heat loads to the first wall. Plasma stability limits and machine-specific technical requirements constrain the stable envelope through which the plasma must be navigated. Large amounts of auxiliary heating are required throughout the ramp-down phase, to avoid a radiative collapse in the presence of intrinsic tungsten and seeded xenon impurities, as quantitatively estimated in this work. As the plasma current is reduced, the current density becomes increasingly peaked, reflected by a growing value of the internal inductance $\ell$ $i3$ , resulting in reduced controllability of the vertical position of the plasma. The feasibility of different plasma current ramp-down rates is tested by applying an automated optimization framework embedding the RAPTOR core transport solver. Optimal time traces for plasma current $I$ $p$ $(t)$ and plasma elongation $κ(t)$ are proposed, to satisfy an $I$ $p$ -dependent upper limit on the plasma internal inductance, as obtained from vertical stability studies using the CREATE-NL code, as well as a constraint on the time evolution of $q$ 95 , to avoid an ideal MHD mode. A negative current density near the plasma edge is observed in our simulations, even for the most conservative $I$ $p$ ramp-down rate, indicating significant transient dynamics due to a large resistive time.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Qualification and Commissioning of Helium Flow Loop Experiment for Blanket Design Measurements

Sufficient cooling of plasma-facing materials remains an outstanding challenge in the design of fusion reactor blankets in commercial power demonstration plants. Due to its chemical inertness and low neutron interaction cross section, pressurized helium is a candidate coolant fluid for such systems; however, helium has a small thermal mass compared to liquid coolants, potentially reducing heat removal performance. To address this need, a number of heat transfer enhancements have been proposed to improve the cooling efficiency of such components, thereby decreasing pumping power needs and improving overall plant efficiency. Toward this end, a helium flow loop experiment (HFLE) has been designed and commissioned to test advanced passive heat transfer enhancements in unit-cell test sections, providing necessary data for model validation and subsequent system design. The HFLE is designed to provide flow of pressurized (up to 4 MPa) helium at flow rates up to 80 g/s, enabling heat transfer and pressure drop measurements in test pieces at Reynolds numbers in excess of 180 000. To explore the effects of novel and complex heat transfer enhancements, test sections are produced via additive manufacturing, providing geometries not typically obtainable by conventional machining. Here in this work, we present results from HFLE commissioning and the initial thermal-hydraulic tests of an additively manufactured rifled-rib test section. Results are compared to smooth pipe correlations, and plans are described for future HFLE measurements. These preliminary experiments indicate the utility of the HFLE for heat transfer enhancement testing and simulation validation activities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Generation of shear flows induced by AE / EPM in LHD plasma

The generation of shear flows (SFs) by Alfven Eigenmodes (AEs) and energetic particle modes (EPMs) have important effects on the operation of future nuclear fusion reactors, because SFs regulate the saturation of the AEs/EPMs, the transport of EPs and thermal plasma, as well as the formation of transport barriers among other consequences. The aim of this study is the analysis of SFs generation during the saturation phase of AEs and EPMs in LHD plasma. Experiments performed in the 23rd and 24th LHD experimental campaigns are dedicated to explore the destabilization of AEs/EPMs in discharges with different heating patterns, thermal plasma and magnetic field configurations. In particular, the shots 176490 and 179697 show the destabilization of MHD bursts and energetic-ion-driven resistive interchange modes (EIC), respectively. Charge exchange spectroscopy measurements in both discharges indicate that the generation of SFs by AE/EPM is uncorrelated with the perturbation induced by the neutral beam injector (NBI). Nonlinear simulations performed using the gyro-fluid code FAR3d show the generation of zonal structures, especially SFs, induced during the saturation phase of Toroidal Alfven Eigenmodes (TAEs) triggered in the MHD burst as well as by the 1/1 EIC in the bursting phase. The simulations indicate that SFs are caused by the radial electric fields powered by energy transfers from the unstable AE/EPM towards the thermal plasma. The strongest SFs are measured during the EIC bursting phase once the 1/1 EPM overlaps with nearby resonances at the plasma periphery. Likewise, the largest SFs during the MHD burst are observed once TAEs radially overlap in the inner-middle plasma region.

AE↗

DOE OSTI2025

Turbulence suppression at extreme plasma densities on DIII-D and EAST

Recent high-poloidal-beta (high-βP) experiments on DIII-D and EAST have made coordinated breakthroughs for high confinement quality at high density near the Greenwald limit. Density gradient amplification of turbulence suppression at high βP can explain both of these achievements. Experiments on DIII-D have achieved Greenwald fraction (fGr = line-averaged density/Greenwald density) above 1 simultaneously with normalized energy confinement (H98y2) around 1.5, as required in fusion reactor designs but never before verified in tokamak experiments with the divertor configuration. A synergy between increased H98y2 and fGr is observed with strong gas puffing, due to the build-up of an internal transport barrier at large radius in the temperature and density channels. Transport simulations reveal that the favorable trend of reduced turbulent energy transport at higher density is only expected when increasing the density gradient at high local safety factor and high β, thus at high βP to ensure strong α-stabilization. These conditions are crucial to many conceptual designs for steady-state reactors. New experiments on EAST have nearly doubled the ion temperature at fGr ∼ 0.9, consistent with predict-first modeling results based on the same physics revealed from the DIII-D analysis. All previous EAST long-pulse H-modes have Ti ≪ Te near plasma axis. Transport modeling indicates that the profiles are limited by ion-temperature-gradient modes at mid-radius. The modeling also suggested potential solutions, including reducing magnetic shear, enhancing density gradients, and higher impurity concentration. Following this guidance, EAST experiments directly show a strong enhancement of Ti achieved with a combination of a second plasma current ramp-up, a density gradient increase, and a Zeff perturbation by a short pulse (100 ms) of impurity injection, as predicted by the earlier modeling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Techno-Economic Analysis of Gas-Liquid Contactors for Tritium Extraction from Lead-Lithium

To enable a sustainable fuel cycle, any deuterium-tritium fusion reactor must breed its tritium fuel onsite. Lead-lithium (PbLi), a eutectic metal, is a leading liquid breeder material for tritium generation. One challenge with PbLi blanket technology is the extraction of tritium from the molten eutectic. Three technologies are the focus of worldwide research: the vacuum permeator, the vacuum sieve tray, and the gas-liquid contactor (GLC). The present work offers a methodology for designing, sizing, optimizing, and costing a trickle-bed GLC. Here, we analyzed tritium extraction from PbLi using MELODIE experimental data by applying traditional packed bed mass transfer efficiency models along with supplementary models, like film theory. Our analysis revealed that traditional packed bed mass transfer efficiency models do not fit the MELODIE loop experimental data. Moreover, uncertainty in PbLi solubility resulted in a 325-fold increase in required gas flow rates when comparing identical packing heights. The film theory liquid mass transfer coefficient, Delt-Olujic wettability model, and Reiter tritium solubility values fit the MELODIE data best and were used both in the design and to conduct the economic analysis. Techno-economic analysis of the GLC was performed to evaluate three design sizes, all achieving a minimum extraction efficiency of 90 [%] for a total tritium extraction of 31 [kg/yr].

Fusion Fuel Cycle↗

DOE OSTI2023

Influence of fatigue precracking and specimen size on Master Curve fracture toughness measurements of EUROFER97 and F82H steels

EUROFER97 and F82H steels are two leading reduced-activation ferritic-martensitic (RAFM) steels for fusion first wall and blanket applications. Exposure to the harsh environment of fusion reactors can result in severe degradation of fracture toughness. Thus, the post-irradiation evaluation of fracture toughness is critical for understanding the material behavior. Due to the space constraints of irradiation facilities and challenges in controlling a uniform irradiation condition for large size specimens, the development of small specimen test techniques (SSTT) is indispensable to evaluate the performance of irradiated materials. In this study, we evaluated specimen size effects on the Master Curve fracture toughness of EUROFER97 and F82H steels. A wide variety of specimens, including 0.5 T compact tension (C(T)) specimens, 0.16 T mini-compact tension (miniC(T)) specimens, and 1.65 mm miniature bend bar specimens, were tested. The testing methodology was based on the Master Curve method in the ASTM E1921 standard. No specimen size effect was observed in 0.5 T C(T) and 0.16 T miniC(T) specimens on the Master Curve reference temperature T0, while 1.65 mm miniature bend bar specimens yielded a higher T 0Q . A strong effect of fatigue precracking on T 0 for 0.5 T C(T) and 0.16 T miniC(T) specimens was observed, such that testing on specimens with skewed fatigue precrack fronts resulted in lower T 0 than for specimens with ASTM standard qualified straight fatigue precrack fronts. The results highlight the importance of experimental quality control in developing SSTT for Master Curve fracture toughness testing. Lastly, we also evaluated and provided recommendations on the minimum number of specimens needed for each specimen type for yielding reliable T 0Q values.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Optimization of lithium vapor box divertor evaporator location on NSTX-U using SOLPS-ITER

Commercial fusion reactors will be faced with extremely high divertor target heat fluxes that will require mitigation. Simulations of detachment in an NSTX-U scenario projected to have 92 MW/m 2 unmitigated peak target heat flux are presented, which reaches sub-10 MW/m 2 target heat flux using a highly dissipating lithium vapor box divertor design. The lithium vapor box is a detached divertor design which employs lithium vapor evaporation and condensation to contain lithium below the X-point. Previous SOLPS modeling has indicated a lithium vapor box can reduce the heat flux down to 10 MW/m 2 via simultaneous evaporation from the Private Flux Region (PFR) and the Common Flux Region (CFR) sides of the vapor box. It is found here that PFR evaporation has improved access to the separatrix leading to significantly more efficient power dissipation than CFR evaporation. Simulations of target evaporation with an evaporation distribution that is self-consistent with the temperature of a Capillary Porous System with Fast flowing liquid lithium (CPSF) could reach n Li / n e ~ 0.025-0.030 at the Last Closed Flux Surface (LCFS) depending on the liquid metal flow speeds and lithium sputtering yield, while PFR-side evaporation can reach acceptable heat fluxes with n Li / n e ~ 0.038 at the LCFS. However, PFR evaporator performance can be improved if the target is allowed to be hot enough such that it reflects lithium, reaching n Li / n e ~ 0.028 and reducing required lithium evaporation. Ultimately PFR evaporation and target evaporation are found to have similar ability to produce acceptable heat flux solutions with minimal upstream concentration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

MX precipitate behavior in an irradiated advanced Fe-9Cr steel: Self-ion irradiation effects on phase stability

In an effort to optimize Fe-9Cr reduced activation ferritic/martensitic (RAFM) steels and to inform the design and operation of fusion reactors, this work represents the first in a series of cohesive studies dedicated to the evolution of MX-TiC precipitates under accelerated single and dual ion irradiations. This study investigates CNA9, a simplified Fe-9Cr RAFM steel featuring initial MX-TiC precipitate densities of (2.3±0.3)×10²¹ m⁻³. This material was subjected to single self-ion irradiation at damage levels ranging from 1 to 100 displacements per atom (dpa) over a temperature range of 300 to 600°C, with a nominal dose rate of 7×10⁻⁴ dpa/s. Irradiation-induced coarsening was observed, as evidenced by statistically significant increases in mean diameter sizes, at 15 dpa at both 500°C and 600°C, whereas no coarsening was noted at 300°C or 400°C. Further, complete dissolution of precipitates occurred at damage levels of 50 and 100 dpa across the two temperatures tested (300°C and 500°C) while no significant changes were observed at any doses below 15 dpa at 500°C. Experimentally parameterized recoil resolution modeling suggests that the observed radiation stability of MX-TiC precipitates is intricately linked to diffusional changes of solutes resulting from the co-evolution of microstructural features within the experiments. The findings align with current theoretical perspectives on radiation-induced precipitate stability in complex alloys.

36 MATERIALS SCIENCE↗

DOE OSTI2024

One-dimensional simulation and validation of divertor detachment induced through nitrogen seeding on HL-2A

Divertor detachment is a promising method to solve the power exhaust problem in tokamak devices or even in future magnetic fusion reactors. In this work, a detachment experiment (HL-2A shot #38008) with mixed gas seeding (60% nitrogen and 40% deuterium) is simulated using the SD1D module in BOUT++. In the process from attachment to detachment, the target electron temperature and the target ion saturation current in simulations are found to be consistent with the experimental results measured by Langmuir probes on the target plate. In order to understand the underlying detachment mechanism on HL-2A, this work analyses the role of different particle species in the cases with different seeding rates. It shows that the plasma density varies little and the density of neutrals (D and D 2 ) slightly decreases with the increase of nitrogen seeding rate, such that plasma–neutral interactions cannot effectively reduce plasma energy and plasma momentum in the divertor. The case with a high seeding rate predicts that increasing seeding rate cannot reach a target temperature lower than 2.5 eV, which is the required temperature for strong plasma–molecule interactions. Thus, the plasma–molecule interactions may not be important in the divertor during nitrogen seeding. Here this work also studies the parallel forces including (1) force due to the parallel electric field, (2) friction forces, (3) ion- and electron-thermal forces, and (4) collisional reactions (e.g. charge exchange recombination and ionisation). It is found that the friction force between nitrogen ions and other particle species (primarily D + ) is the dominant force towards the target, while ion- and electron-thermal forces are the dominant force pushing nitrogen ions back to upstream. Parallel forces determine the parallel distribution of nitrogen impurities, and therefore decide the region of nitrogen radiation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Material Plasma Exposure eXperiment (MPEX) High Heat Flux Bellows for Component Alignment in High Microwave Environment

The Material Plasma Exposure eXperiment (MPEX) device is a linear plasma device developed to perform plasma material interaction experiments under the conditions prototypic of a fusion reactor divertor. MPEX has multiple systems that must be precisely aligned to the plasma axis, including an electron cyclotron heating system that emits up to 400 kW of microwave power into the vacuum vessel. Five distinct systems require precise alignment on the MPEX device, thus requiring four bellows, all of which are adjacent to the plasma at a relatively high heat flux of approximately 47 kW/m2 and microwave power regions. The MPEX high heat flux bellows (HHFB) is designed to deliver 6 degrees of freedom positioning. The HHFB includes titanium–zirconium–molybdenum (TZM) inserts that are brazed into a Glidcop AL-15 body using a high-temperature braze alloy, thus blocking direct line of sight to an edge-welded bellows from the plasma and microwave screen to block microwaves from the bellows. Further, a custom ConFlat knife edge is machined into the Glidcop AL-15, so the vacuum flanges do not need a braze or weld joint on the vacuum interface. Fingerstock or copper mesh is used to restrict microwave power from entering the interstitial space between the water-cooled Glidcop AL-15 body and edge-welded bellows. Glidcop AL-15 was selected as the material of choice for the water-cooled body because it can maintain mechanical integrity at elevated temperatures, and it also allows for a high-temperature braze. TZM was selected for its machinability and compatibility with vacuum and plasma requirements. A test article is also being considered for a similarly shaped component, the MPEX limiter, that will demonstrate the integrity of the braze joint under high thermal load. Results from this testing will be extrapolated to deduce the lifetime and integrity of the HHFB design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Innovative laser-based methods for monitoring fuel retention in ITER

This paper addresses the challenge of tritium inventory management in ITER and future fusion reactors, highlighting the importance of accurate tritium measurement and its spatial distribution within the vacuum vessel. Given ITER’s operational constraints, especially the limit on tritium retention, precise measurement is essential for both safety and regulatory compliance. To tackle these questions, the paper presents the T-monitor diagnostic system developed by Forschungszentrum Jülich, which uses Laser-Induced Desorption (LID) in combination with Diagnostic Residual Gas Analysis (DRGA) to measure hydrogen isotope concentrations on the surface of divertor tiles. The system integrates a high-power laser, advanced optical components, and a Fast Scanning Mirror Unit (FSMU) for accurate laser spot positioning with rapid response. Designed to measure in situ tritium retention, the diagnostic provides high-resolution spatial mapping, vital for evaluating detritiation strategies. The laser heating process increases the divertor surface temperature to 1600 K within the laser spot, promoting hydrogen isotope desorption. Accurate measurements require the precise control of laser parameters, including pulse duration and spot size, with a target relative accuracy of 20%. The optical design includes both in-vessel and ex-vessel components, such as durable high-reflectivity mirrors made of gold and copper, selected not only for their infrared performance but also for their transmission of visible wavelengths for observation purposes. To protect optical components from contamination, a pneumatic shutter is used.

Hydrogen isotopes↗

DOE OSTI2022

Benchmarking a 9Cr-2WVTa Reduced Activation Ferritic Martensitic Steel Fabricated via Additive Manufacturing

Reduced activation ferritic (RAF) martensitic steels are promising candidates for the first wall of fusion reactors. However, current manufacturing capabilities call for these components to be made by welding wrought plates. This limits design freedom and necessitates the use of post-weld heat treatments (PWHT) in accordance with the boiler and pressure vessel code. Additive manufacturing (AM) can offer a unique solution to solve this challenge by leveraging the layer-wise deposition strategy to come up with temper bead deposition techniques to eliminate post-processing heat treatments (PPHT). However, it is necessary to benchmark the properties of RAF steels fabricated by AM with their wrought counterparts to identify the process-structure-property correlation, which is the goal of this study. The study demonstrates that while tensile properties at room temperature and high temperatures are satisfactory, the as fabricated and samples after PPHT have significant heterogeneity in tensile elongation. This has been attributed to the presence of discontinuities in the build. The as-fabricated samples have an average tensile strength of 1190 + 12 MPa and an average elongation of 15 + 5% at room temperature and 658 ± 20 MPa ultimate tensile strength (UTS) and 14 ± 7% at 600 °C. After the post-weld heat treatment, mechanical properties decrease to around 600–650 MPa and an elongation between 20–25% at room temperature to 300 MPa UTS and 25–28% elongation at 600 °C. The characterization of microstructures at various length scales demonstrates that the as-fabricated structure has a significant fraction of delta ferrite in a lath martensitic matrix. No precipitates could be identified in the as-fabricated structure. PPHT led to a decrease in the area fraction of delta ferrite and precipitation of M 23 C 6 and MX. Detailed characterization clearly demonstrates that the lack of precipitates in the as-fabricated structure could be due to the slow tempering response of the alloy. Finally, the needs to develop new alloys to achieve the objectives stated above are articulated.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Density drop at the divertor target in the prototype material plasma exposure eXperiment (Proto-MPEX)

The steady-state linear device “Material Plasma Exposure eXperiment” (MPEX) is currently under construction at Oak Ridge National Laboratory with the goal of enabling Plasma-Material Interaction studies at future fusion reactor relevant plasma conditions. In this work, a newly in-house developed hybrid Particle-In-Cell code-PICOS++ is applied to understand the experimental results obtained from the prototype of MPEX referred to as the “Proto-MPEX” during its helicon-only and helicon with ion cyclotron resonance heating (ICRH) experiments. This study explains the physics of the experimentally observed plasma density-drop at the divertor target in Proto-MPEX device during ICRH. In contrast to previous work on ICRH in MPEX, this study demonstrates that the mirror force plays a central role in the Proto-MPEX plasma transport during ICRH, which has new features not previously explored. Force balance analyses reveal that the temperature anisotropy produced by ICRH leads to a significant increase in the mirror force downstream of the resonance where the magnetic field is diverging. This force accelerates ions toward the target and leads to a drop in plasma density to ensure conservation of particle flux. Simulations with ICRH where the magnetic field divergence downstream of the resonance has been removed, do not produce plasma acceleration nor density drop at the target despite efficient ion heating at the resonance. Moreover, simulation results demonstrate that for a given ICRH power, lowering the source rate produces ions with increased perpendicular energy which interact with the mirror force to produce higher plasma acceleration which increases the strength of the density-drop at the target. The strength of the density drop appears to reach an asymptotic limit at a certain threshold ICRH power. Simulations show that this threshold power increases with increasing particle source rate.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗