Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “friction experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

"Coulombic Viscosity" In Granular Materials: Planetary and Astrophysical Implications

The term "Coulombic viscosity" is introduced here to define an empirically observed phenomenon from experiments conducted in both microgravity, and in ground-based 1-g conditions. In the latter case, a sand attrition device was employed to test the longevity of aeolian materials by creating two intersecting grain-circulation paths or cells that would lead to most of the grain energy being expended on grain-to-grain collisions (simulating dune systems). In the areas in the device where gravitationally-driven grain-slurries recycled the sand, the slurries moved with a boundary-layer impeded motion down the chamber walls. Excessive electrostatic charging of the grains during these experiments was prevented by the use of an a.c. corona (created by a Tesla coil) through which the grains passed on every cycle. This created both positive and negative ions which neutralized the triboelectrically-generated grain charges. When the corona was switched on, the velocity of the wall-attached slurries increased by a factor of two as approximately determined by direct observation. What appeared to be a freely-flowing slurry of grains impeded only by intergranular mechanical friction, had obviously been significantly retarded in its motion by electrostatic forces between the grains; with the charging reduced, the grains were able to move past one another without a flow "viscosity" imposed by the Coulombic intergranular forces. A similar phenomenon was observed during microgravity experiments aboard Space Shuttle in USML-1 & USML-2 spacelabs where freely-suspended clouds of sand were being investigated for their potential to for-m aggregates. In this environment, the grains were also charged electrostatically (by natural processes prior to flight), but were free from the intervention of gravity in their interactions. The grains were dispersed into dense clouds by bursts of air turbulence and allowed to form aggregates as the ballistic and turbulent motions damped out. During this very brief (30-60 sec) damping period, motion of the grains was observed to be retarded by the electrostatic interactions. The fact that the grains almost instantly formed aggregates was evidence that their ballistic motions had been constrained and redirected by the dipole-dipole interactions that led to filamentary aggregate development. Undoubtedly, the "Coulombic viscosity" of the cloud assisted in damping grain motion so rapidly. The electrostatically-induced grain-cloud viscosity or drag exerted on grain motion, is a complex function of three major parameters: charge magnitude, charge sign, and mean intergranular distance. The above experiments illustrate one particular type of granular behavior. The discussion here will therefore be restricted to drag relationships: (a) between grains that are naturally charged triboelectrically and thus exhibit dipole-dipole attractions between one another even if there are slight net charges present (which can be overwhelmed by dipole coupling at short distances), and (b) between grains that are densely spaced where the intergranular distance varies between zero and some value (usually tens or hundreds of grain diameters) that permits each grain to detect the dipole moment of another grain -- the distance is not so great that other grains appears as neutral electrical "singularities. I. Aeolian transport: During motion of grains in a saltation cloud (on Earth, Mars, or Venus), triboelectric charging must occur as a result of multiple grain contacts, and by friction with the entraining air. A situation might develop that is similar to the one described above in the attrition device: grain motion becoming significantly retarded (reduced flux) as grains find it increasingly difficult to either separate from the surface, or to pass one another without Coulombic retarding forces. A "Coulombic drag" will exist at flux initiation and increase with time to work in direct opposition to the aerodynamic drag that drives the grain motion. It is predicted that this will lead to an increase with time of both the aerodynamic and bed-dilatancy thresholds (3). Because of Paschen discharge effects in the martian atmosphere, the electrostatic charging in a saltation cloud may be partially abated, but this will lead to greater grain mobility, more charging, and thus to a charge-discharge steady state mediated by mechanical interactions. II. Dry colluvial systems: Sand avalanches on dunes, dry debris flows, talus flows, avalanches, and pyroclastic surges are examples of gravity-driven, dense granular flows where rock/grain fragmentation and grain-to-grain interactions cause triboelectrification (sometimes augmented by other electrical charging processes), and where the grain densities of the systems are such that strong dipole-dipole interactions between grains might be expected to be present. Because it is expected that the Coulombic forces between grains will cause a sluggishness or enhanced granular-flow viscosity, the motion of a grain mass will be retarded or damped so that this will assist, ultimately, in terminating the flow. The greatest Coulombic viscosity will be created in the most highly charged systems, which will also be the most energetic. Thus, grain flows have some tendency to be self-limiting by internal energy partitioning; gravitational potential is converted to Coulombic potential, which manifests itself as a drag force between the grains. III. Volcanic eruption plumes and impact ejecta curtains: The violence of these systems leads to powerful electrical charging of particulates. Lightning storms emanating from volcanic plumes are a testimony to the levels of charging. As pyroclastic grains interact forcefully and frequently within eruption plumes, it is reasonable to predict that the internal turbulent motions of the plume will be significantly damped by the Coulombic viscosity exerted by grain charges. Additional information is contained in the original.

Marshall, J. R.↗

Dynamic behavior of the mercury damper

The dynamic behavior of the mercury nutation damper is investigated. Particular attention is paid to the eccentric annular mercury configuration, which is the final continuous ring phase that occurs in the operation of all mercury dampers. In this phase, damping is poorest, and the system is closely linear. During the investigation, the hydrodynamic problem is treated as three dimensional, and extensive use is made of a variational principle of least-viscous frictional power loss. A variational principle of least-constraint is also used to advantage. Formulas for calculating the behavior of the mercury damper are obtained. Some confirmatory experiments were performed with transparent ring channels on a laboratory gyroscope. Selected movie frames taken during wobble damping are shown along with the results of film measurements.

Crout, P. D.↗

Comparison of Several Different Sputtered Molybdenum Disulfide Coatings for Use in Space Applications

Tribology experiments on different types of sputtered molybdenum disulfide (MoS2) coatings (obtained from different vendors) using accelerated testing techniques were conducted. The purpose was to determine which would be the best coating for use with auxiliary journal bearings for spacecraft energy storage flywheels. Experiments were conducted in moist air (50% relative humidity) and in dry air (<100 PPM water vapor content) on a Pin-on-Disk Tribometer to determine how well the coatings would perform in air. Experiments were also conducted on a Block-on-Ring Tribometer in dry nitrogen (<100 PPM water vapor) to simulate how well the coatings would perform in vacuum. Friction, counterface wear, coating wear, endurance life and surface morphology were investigated.

Fusaro, Robert L.↗

Electrostatic Regolith Interaction Experiment (ERIE) Electrometer Initial Flight Results

The Electrostatic Regolith Interaction Experiment (ERIE) is a suborbital flight payload studying electrostatically charged dust particle dynamics under microgravity, jointly developed by University of Central Florida (UCF) and NASA Kennedy Space Center (KSC). ERIE combines components from two systems, the COLLisions Into Dust Experiment (COLLIDE) from UCF and the Wheel Electrostatic Spectrometer (WES) from NASA KSC, to advance understanding of charged grain behavior on low gravity bodies such as the Moon and asteroids. ERIE slides a door containing an electrometer system monitoring various insulating disks across the surface of a regolith simulant bed. The experiment is activated when the payload enters the microgravity potion of the flight. The grains in the simulant bed tribocharge via agitation during launch as well as through frictional interactions with the door and its protruding insulators. As the retention door retracts, particles are allowed to loft into an open volume, achieving motion due to electrostatic repulsion. The electrometer system measures the charge transfer between the granular material and the insulators. As the charged grains exit the bed, they travel through an applied electric field and a camera observes the kinematics of the individual grains whose trajectories are determined by their net charges. The design of the ERIE electrometer instrument and initial results from the first flight was presented at the 2021 AGU Fall Meeting under P55E-2002. Shortly after microgravity was achieved and the retaining door began to open, the rate of charge acquisition measured by the electrometer increased, indicating the insulators were accumulating triboelectric charge. Charged grains were observed in the video data to traverse across the external electric field and become deflected from a linear path due to their charges. Pairs of grains were also observed to orbit one another as expected from two oppositely charged bodies in proximity to one another. Improvements to the design of the instrument and preliminary results obtained from the second flight scheduled for Q3 2022 will be presented at this meeting.

Electrostatics↗

Electrostatic Regolith Interaction Experiment (ERIE) Electrometer Initial Flight Results

The Electrostatic Regolith Interaction Experiment (ERIE) is a suborbital flight payload studying electrostatically charged dust particle dynamics under microgravity, jointly developed by University of Central Florida (UCF) and NASA Kennedy Space Center (KSC). ERIE combines components from two systems, the COLLisions Into Dust Experiment (COLLIDE) from UCF and the Wheel Electrostatic Spectrometer (WES) from NASA KSC, to advance understanding of charged grain behavior on low gravity bodies such as the Moon and asteroids. ERIE slides a door containing an electrometer system monitoring various insulating disks across the surface of a regolith simulant bed. The experiment is activated when the payload enters the microgravity potion of the flight. The grains in the simulant bed tribocharge via agitation during launch as well as through frictional interactions with the door and its protruding insulators. As the retention door retracts, particles are allowed to loft into an open volume, achieving motion due to electrostatic repulsion. The electrometer system measures the charge transfer between the granular material and the insulators. As the charged grains exit the bed, they travel through an applied electric field and a camera observes the kinematics of the individual grains whose trajectories are determined by their net charges. The design of the ERIE electrometer instrument and initial results from the first flight was presented at the 2021 AGU Fall Meeting under P55E-2002. Shortly after microgravity was achieved and the retaining door began to open, the rate of charge acquisition measured by the electrometer increased, indicating the insulators were accumulating triboelectric charge. Charged grains were observed in the video data to traverse across the external electric field and become deflected from a linear path due to their charges. Pairs of grains were also observed to orbit one another as expected from two oppositely charged bodies in proximity to one another. Improvements to the design of the instrument and preliminary results obtained from the second flight scheduled for Q3 2022 will be presented at this meeting.

Electrostatics↗

Mechanism of lubrication by tricresylphosphate (TCP)

The coefficient of friction was measured as a function of temperature on a pin-on-disk tribometer. Pins and disks of 440C and 52100 steels were lubricated with tricresylphosphate (TCP), 3.45 percent TCP in squalene, and pure squalene. The M-50 pins and disks were lubricated with 3.45 percent TCP in squalene and pure squalene. Experiments were conducted under limited lubrication conditions in dry ( 100 ppm H2O) air and dry ( pp H2O) nitrogen at 50 rpm (equivalent to a sliding velocity of 13 cm sec) and a constant load of 9.8 N (1 kg). Characteristic temperatures T sub r were identified for TCP on 52100 steel and for squalene on M-50 and 52100 steels, where the friction decreased because of a chemical reaction between the lubricant and the metal surface. The behavior of squalene obscured the influence of 3.45 percent TCP solute on the friction of the system. Wear volume measurements demonstrated that wear was lowest at temperatures just above T sub r. Comparing the behavior of TCP on M-50, 440C, and 52100 steels revealed that the TCP either reacted to give T sub r behavior or produced initial failure in the temperature range 223 + or - 5 C.

Faut, O. D.↗

Re-examination of compliant wall experiments in air with water substrates

A possible alternative explanation is proposed for compliant wall drag reductions measured in previous investigations. Standing waves were observed to form on the surfaces of compliant wall models in air with water substrates as the freestream velocity was increased from 15 to 30 m/s. These waves resembled sine waves with half of the wave protruding over the upstream portion of the model and the other half being recessed over the downstream end of the model. These data coupled with results of recent drag reduction experiments suggest that standing waves could have caused a shift in the model center of gravity creating a bending moment that was interpreted as a reduction in the skin friction drag.

Hefner, J. N.↗

Investigation of blown boundary layers with an improved wall jet system

Measurements were made in a two dimensional incompressible wall jet submerged under a thick upstream boundary layer with a zero pressure gradient and an adverse pressure gradient. The measurements included mean velocity and Reynolds stresses profiles, skin friction, and turbulence spectra. The measurements were confined to practical ratios (less than 2) of the jet velocity to the free stream velocity. The wall jet used in the experiments had an asymmetric velocity profile with a relatively higher concentration of momentum away from the wall. An asymmetric jet velocity profile has distinct advantages over a uniform jet velocity profile, especially in the control of separation. Predictions were made using Irwin's (1974) method for blown boundary layers. The predictions clearly show the difference in flow development between an asymmetric jet velocity profile and a uniform jet velocity profile.

Saripalli, K. R.↗

Planetary and Primitive Object Strength Measurement and Sampling Apparatus

Support is requested for continuation of a program of dynamic impact (harpoon) coring of planetary, comet, or asteroid surface materials. We have previously demonstrated that good quality cores are obtainable for planetary materials with compressive strengths less than 200 MPa. Since the dynamics of penetration are observable on a Discovery class spacecraft, which images the sampling operation, these data can be used with a model developed under this project, to measure in-situ strength and frictional strength of the crust of the object. During the last year we have developed a detailed analytic model of penetrator mechanics. Progress is reported for the solid penetrators experiments, the CIT penetrator model, and the impact spall sampling apparatus.

Ahrens, Thomas J.↗

Results of the Imager for Mars Pathfinder Windsock Experiment

The IMP windsock experiment measured wind speeds at three heights within 1.2 m of the martian surface during Pathfinder landed operations. Data from the strongest breezes indicate aerodynamic roughness = 3 cm, wind friction speeds up to 1 m/sec.

Sullivan, R.↗

Implementation and Verification of the SST-𝜸 and SA-AFT Transition Models in FUN3D

The transition modeling capability in the NASA unstructured FUN3D suite of codes has been augmented by incorporating two additional transport-equation-based transition models, namely, the 𝜸 transition model coupled with Menter’s 2003 Shear-Stress Transport (SST) turbulence model and Coder’s Amplification Factor Transport (AFT) transition model combined with the Spalart-Allmaras (SA) turbulence model. Both of these models, SST-𝜸 and SA-AFT, are used to compute transition characteristics of several test cases from the literature. The selected test cases cover a range of transition scenarios including bypass transition over a flat plate (ERCOFTAC T3A and T3A- flow configurations), transition in the presence of separation bubbles (NLF-0416 airfoil at selected angles of attack), and natural transition due to Tollmien-Schlichting instabilities (flat-plate experiment by Schubauer and Klebanoff). To address the urgent need for model verification as highlighted in recent workshops on transition modeling, the drag, lift, surface pressure, and skin-friction coefficients from the FUN3D solutions for a sequence of meshes are compared with the results obtained with the same models implemented in the NASA structured grid flow solver OVERFLOW. Comparisons between the local and global surface coefficients from the FUN3D and OVERFLOW solvers for all test cases resulted in good agreement for the finest meshes.

Verification↗

Thin-wall Internal Channel Geometry and Surface Enhancements for Heat Exchangers using Laser Powder Directed Energy Deposition

Additive Manufacturing (AM) has offered many new design and manufacturing opportunities for components across various industries. As AM evolves there is a need to better understand outputs of the process including geometric limitations, surface texture, and post-processing surface enhancements for specific application requirements. One possible application area of AM are components using thin-wall (~1 mm) microchannel heat exchangers for subsystems across aerospace and industrial applications. Laser Powder Bed Fusion (L-PBF) is a common process for complex internal channels but the build diameter is limited to approximately 600 mm. Laser Powder Directed Energy Deposition (LP-DED) is being evaluated to produce thin-wall microchannel heat exchangers at scales beyond the L-PBF process. Successful deployment of the LP-DED technology requires characterization of geometric features from the process and potential improvements to the surface using post-processing. Surface texture, inclusive of roughness and waviness, is one of the critical attributes of AM that effects the friction factor and pressure drop within a heat exchanger and lacks data for the LP-DED process. This presentation will provide an overview of the characterization work completed of the LP-DED process for thin-walls and small channel geometry representative of various high performance alloys including NASA HR-1 and GRCop-42. An overview of the experiments conducted with varying LP-DED parameters, evaluation of various internal channel geometry, geometric build features, and resulting surface texture will be provided along with a summary of conclusions from these experiments. This study presents characterization of 2.5 mm microchannels using LP-DED, mechanisms that cause the surface texture which include powder adherence and material droop, and angled walls have a significant impact on the thickness and surface texture. Results will also be presented on various surface enhancement processes that allow for tuning of the wetting surface for friction factor, heat transfer, or fatigue life performance requirements.

Additive Manufacturing↗

PS300 Tribomaterials Evaluated at 6500C by Bushing Test Rig

A new facility has been developed to test the tribological behavior (friction and wear) of PS300 solid lubricant bushings at high temperatures. PS300 is a commercially available solid lubricant invented at the NASA Glenn Research Center. It can be prepared as a plasma spray coating or as a free-standing powder metallurgy component, designated PM300. PS300 and PM300 composites are designed to lubricate sliding components at temperatures above the capability of today's best oils, greases, and solid lubricants. One of the primary applications being pursued for PM300 is the development of bushings for use in high-temperature machinery. Examples include inlet guide vane bushings for gas turbines and conveyors, and bearings for industrial furnaces and ovens. Encouraging preliminary field trials indicate that PS300 and PM300 lubricant materials have been commercialized successfully in several industrial applications. However, the lack of laboratory performance data has hindered further commercialization especially for new applications that differ significantly from the established experience base. The purpose of the newly developed bushing test rig will be to determine the performance characteristics of PM300, and other materials, under conditions closely matching intended applications. The data will be used to determine engineering friction and wear rates and to estimate the life expectancy of bushings for new applications. In the new rig, the bushing is loaded against a rotating shaft inside a furnace enclosure (see the preceding photograph). Loads can vary from 5 to 200 N, speeds from 1 to 400 rpm, and temperatures from 25 to 800 C. Furnace temperature, bushing temperature, shaft speed, and torque are monitored during the test, and wear of both the bushing and the shaft is measured after testing is completed. Initially, PM300 bushings will be evaluated and compared with lower temperature, traditional bushing materials like graphite and porous bronze. The baseline PM304 composition is 60 wt% NiCr (a binder), 20 wt% Cr2O3 (a hardener), 10 wt% BaF2/CaF2 (a high-temperature lubricant), and 10 wt% Ag (a low-temperature lubricant). Future research efforts will include determining the effects of load, sliding speed, and temperature on tribological performance and, possibly, tailoring composition for specific applications. We expect that the availability of measured performance data will enhance the market penetration of PM300 technology.

Striebing, Donald R.↗

Mars Exploration Rovers as Virtual Instruments for Determination of Terrain Roughness and Physical Properties

The two 2003 Mars Exploration Rovers (MERs), in combination with the Athena Payload, will be used as virtual instrument systems to infer terrain properties during traverses, in addition to using the rover wheels to excavate trenches, exposing subsurface materials for remote and in-situ observations. The MERs are being modeled using finite element-based rover system transfer functions that utilize the distribution of masses associated with the vehicle, together with suspension and wheel dynamics, to infer surface roughness and mechanical properties from traverse time series data containing vehicle yaw, pitch, roll, encoder counts, and motor currents. These analyses will be supplemented with imaging and other Athena Payload measurements. The approach is being validated using Sojourner data, the FIDO rover, and experiments with MER testbed vehicles. In addition to conducting traverse science and associated analyses, trenches will be excavated by the MERs to depths of approximately 10-20 cm by locking all but one of the front wheels and rotating that wheel backwards so that the excavated material is piled up on the side of the trench away from the vehicle. Soil cohesion and angle of internal friction will be determined from the trench telemetry data. Emission spectroscopy and in-situ observations will be made using the Athena payload before and after imaging. Trenching and observational protocols have been developed using Sojourner results; data from the FIDO rover, including trenches dug into sand, mud cracks, and weakly indurated bedrock; and experiments with MER testbed rovers. Particular attention will be focused on Mini-TES measurements designed to determine the abundance and state of subsurface water (e.g. hydrated, in zeolites, residual pore ice?) predicted to be present from Odyssey GRS/NS/HEND data.

R E Arvidson↗

The relationship between the microwave radar cross section and both wind speed and stress: Model function studies using Frontal Air-Sea Interaction Experiment data

The Frontal Air-Sea Interaction Experiment (FASINEX) provided a unique data set with coincident airborne scatterometer measurements of the ocean surface radar cross section (RCS)(at Ku band) and near-surface wind and wind stress. These data have been analyzed to study new model functions which relate wind speed and surface friction velocity (square root of the kinematic wind stress) to the radar cross section and to better understand the processes in the boundary layer that have a strong influence on the radar backscatter. Studies of data from FASINEX indicate that the RCS has a different relation to the friction velocity than to the wind speed. The difference between the RCS models using these two variables depends on the polarization and the incidence angle. The radar data have been acquired from the Jet Propulsion Laboratory airborne scatterometer. These data span 10 different flight days. Stress measurements were inferred from shipboard instruments and from aircraft flying at low altitudes, closely following the scatterometer. Wide ranges of radar incidence angles and environmental conditions needed to fully develop algorithms are available from this experiment.

Weissman, David E.↗

A study of turbulence models for prediction of transitional boundary layers

Calculations of two-dimensional transitional boundary layer flows in zero and favorable pressure gradients are presented. The major focus is on the evaluation of current turbulence models to predict quantities such as skin-friction and heat transfer coefficients. Three turbulence models using the mixing length concept along with a one-equation model are considered. These models are tested by comparison with the experiments of Blair and Werle, who investigated flows over a heated flat plate for various levels of free-stream turbulence.

Abid, Ridha↗

Numerical study to assess sulfur hexafluoride as a medium for testing multielement airfoils

A methodology is described for computing viscous flows of air and sulfur hexafluoride (SF6). The basis is an existing flow solver that calculates turbulent flows in two dimensions on unstructured triangular meshes. The solver has been modified to incorporate the thermodynamic model for SF6 and used to calculate the viscous flow over two multielement airfoils that have been tested in a wind tunnel with air as the test medium. Flows of both air and SF6 at a free-stream Mach number of 0.2 and a Reynolds number of 9 x 10(exp 6) are computed for a range of angles of attack corresponding to the wind-tunnel test. The computations are used to investigate the suitability of SF6 as a test medium in wind tunnels and are a follow-on to previous computations for single-element airfoils. Surface-pressure, lift, and drag coefficients are compared with experimental data. The effects of heavy gas on the details of the flow are investigated based on computed boundary-layer and skin-friction data. In general, the predictions in SF6 vary little from those in air. Within the limitations of the computational method, the results presented are sufficiently encouraging to warrant further experiments.

Bonhaus, Daryl L.↗

Percussive Force Magnitude in Permafrost

An in-depth look at percussive drilling shows that the transmission efficiency is very important; however, data for percussive drilling in hard rock or permafrost is rarely available or the existing data are very old. Transmission efficiency can be used as a measurement of the transmission of the energy in the piston to the drill steel or bit and from the bit to the rock. Having a plane and centralized impact of the piston on the drill steel can optimize the transmission efficiency from the piston to the drill steel. A transmission efficiency of near 100% between piston and drill steel is possible. The transmission efficiency between bit and rock is dependent upon the interaction within the entire system. The main factors influencing this transmission efficiency are the contact area between cutting structure and surrounding rock (energy loss due to friction heat), damping characteristics of the surrounding rock (energy dampening), and cuttings transport. Some of these parameters are not controllable. To solve the existing void regarding available drilling data, an experiment for gathering energy data in permafrost for percussive drilling was designed. Fifteen artificial permafrost samples were prepared. The samples differed in the grain size distribution to observe a possible influence of the grain size distribution on the drilling performance. The samples were then manually penetrated (with a sledge-hammer) with two different spikes.

Eustes, A. W., III↗