Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Shock-induced kinetics and cellular structures of liquid nitromethane detonation

Using a combination of high-speed diagnostics, optical pyrometry, velocimetry and video photography, we examine the spatiotemporal reaction kinetics of a prototypical high-energy explosive, liquid nitromethane (NM), as we drive this high explosive into detonation. The detonations were initiated by powerful shock waves whose durations (4 ns) were shorter than the characteristic time associated with the reaction (7 ns). Simple optical spectroscopy alone cannot characterize the kinetics with high time resolution because the reactants and products are flowing at a high velocity of ~6 km/s (6 µm/ns). Additionally, every detection volume behind the shock front contains material initiated over a range of times. High spatial resolution can be obtained by probing interfaces where the shock enters or breaks out of the NM. In addition, we obtain cellular patterns imprinted on the luminous shock front by the two-stage explosion in NM. These spatiotemporal patterns arise naturally as a result of the asymmetry produced by the moving shock front. In this way the shock front serves as a thin moving intrinsic optical gauge that reports and characterizes the two-stage NM explosion behind the front.

42 ENGINEERING↗
DOE OSTI2020

The effects of outdoor air-side fouling on frost growth and heat transfer characteristics of a microchannel heat exchanger: An experimental study

Air source heat pumps have the potential to efficiently heat and cool buildings, but their effectiveness in many climates is limited by frost growth on the outdoor heat exchanger in heating mode. These heat exchanger coils are also subject to fouling from fibers and particulates outdoors. Frost and fouling have each independently been studied extensively, and newly available research on fouling provides a method to realistically foul the air-side of coils in the laboratory. The current paper uses this method to conduct the first laboratory study of the important interactions between fouling and frost growth for a heat pump outdoor coil. A microchannel heat exchanger is tested clean and fouled, with variations in fouling level, humidity, and initial face velocity of air. Air flow rate is allowed to vary with resistance, and a surprising result is that light fouling increases heat transfer and frost growth rates, even with a 3.5% reduction in initial airflow caused by the fouling. However, heavier fouling decreases both rates. When frost growth is normalized to heat transfer, it is found to be increased by fouling; i.e. the coil’s sensible heat ratio decreases.

42 ENGINEERING↗
DOE OSTI2021

A reactive flow model for the 3,3'-diamino-4,4'-azoxyfurazan based plastic bonded explosive (PBX 9701)

Here, this paper describes the calibration of the Arrhenius Wescott–Stewart–Davis (AWSD) reactive flow model for the recently developed high explosive PBX 9701, which consists of 97% 3,3'-diamino-4,4'-azoxyfurazan (DAAF) and 3% FK-800 binder by weight. DAAF-based explosive formulations have several desirable qualities as they are relatively insensitive to non-shock insults but have higher performance than triaminotrinitrobenzene based formulations. Equations of state for the explosive reactants and products are calibrated using a combination of existing and new experimental data and theoretical calculations. The AWSD rate law calibration utilizes both one-dimensional shock-to-detonation and multidimensional rate stick experiments to capture the shock initiation and propagating detonation regimes. Validation of the calibrated model is demonstrated through comparison with recent gas-gun experiments.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2024

Modification of wind turbine wakes by large-scale, convective atmospheric boundary layer structures

In this study, we consider the impact of large-scale, convective structures in an unstable atmospheric boundary layer on wind turbine wakes. Simulation data from a high-fidelity large-eddy simulation (LES) of the AWAKEN wind farm site matching unstable atmospheric conditions were analyzed, and both turbine performance and wake behavior were affected based on their location relative to the convective structures. Turbines located in updraft regions of the flow experienced lower inflow velocity and generated less power, but their wakes were observed to recover faster and saw greater turbulent kinetic energy mixing higher in the boundary layer. The opposite effect was found for turbines in the downdraft regions of the convective structures. A simplified model of this wake behavior was also developed based on a two-dimensional k–ε Reynolds-Averaged Navier–Stokes formulation. This simplified model included the effects of vertical transport, but could be efficiently solved as a parabolic system, and was found to capture similar wake modifications observed in the high-fidelity LES computations.

16 TIDAL AND WAVE POWER↗
DOE OSTI2024

A Vision–based Robust $\mathcal{H}$ ∞ Gain Scheduling Longitudinal and Lateral Following Controller for Autonomous Vehicles on Urban Curved Roads

Implementing advanced driver assistance systems (ADAS) in congested and intricate urban traffic scenarios poses significant challenges. To address the frequent stop–and–go motions exhibited by autonomous vehicles (AVs) navigating urban roads with changes in curvature, we propose a vision–based robust $\mathcal{H}$ ∞ adaptive cruise control system (ACC) for longitudinal control, plus a lane keeping assist system (LKAS) for lateral control. For the vision-based ACC, a weighted probability objective function for the vehicle following behavior is formulated. We incorporate $\mathcal{H}$ ∞ performance and gain scheduling techniques to mitigate the impact of uncertainty in visual sensor measurements. Furthermore, the optimal time headway is scheduled based on the velocity to ensure traffic flow efficiency and safety during the vehicle following process. For the LKAS, we introduce a road curvature estimation method that integrates lane and vehicle dynamics information to obtain the lateral and heading offsets. Next, the design criterion of the observer–based robust gain scheduling lateral motion controller is established by linear matrix inequality (LMI). Here, a series of experiments conducted within a camera–in–loop platform validate the proposed method.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Convection in Scaled Turbine Internal Cooling Passages With Additive Manufacturing Roughness

Abstract Additive manufacturing processes, such as direct metal laser sintering (DMLS), enable the creation of novel turbine cooling internal passages and systems. However, the DMLS method produces a significant and unique surface roughness. Previous work in scaled passages analyzed pressure losses and friction factors associated with the rough surfaces, as well as investigated the velocity profiles and turbulent flow characteristics within the passage. In this study, the heat transfer characteristics of scaled additively manufactured surfaces were measured using infrared (IR) thermography. Roughness panels were CNC machined from plates of aluminum 6061 to create near isothermal roughness elements when heated. Fluid resistance differences between the aluminum roughness panels and roughness panels constructed from ABS plastic using the same roughness patterns from McClain et al. (2020, “Flow in a Simulated Turbine Blade Cooling Channel With Spatially Varying Roughness Caused by Additive Manufacturing Orientation,” ASME Turbo Expo 2020, Turbomachinery Technical Conference and Exposition, Virtual Conference, Sept. 21–25, GT2020-16069) were investigated. Finally, the overall thermal performance enhancements and friction losses were assessed through the calculation of surface averaged “global thermal performance” ratios. The global thermal performance characterizations indicate results in-line with those found for traditional commercial roughness and slightly below traditional internal passage convection enhancement methods such as swirl chambers, dimples, and ribs. The passages investigated in this study do not include compressibility effects or the long-wavelength artifacts and channel geometric deviations observed by Wildgoose et al. (2020, “Impact of Additive Manufacturing on Internal Cooling Channels with Varying Diameters and Build Directions,” ASME Turbo Expo 2020, Turbomachinery Technical Conference and Exposition, Virtual Conference, Sept. 21–25, GT2020-15049). However, the results of this study indicate that, based on the roughness augmentation alone, artificial convective cooling enhancers such as turbulators or dimples may still be required for additively manufactured turbine component cooling.

Engineering↗
DOE OSTI2024

Modeling Dense Particle Flow in Multistage and Obstructed Flow Receivers Using High Fidelity Simulations

Particles are a leading contender for next-generation, concentrating solar power technologies, and the design of the particle receiver is critical to minimize the levelized cost of electricity. Falling particle receivers (FPRs) are a viable receiver concept, but many new designs feature complex particle obstructions that include dense discrete phase flows. This creates additional challenges for modeling as particle-to-particle interactions (i.e., collisions) and particle drag become more complex. To improve upon existing modeling strategies, a CFD-DEM simulation capability was created by coupling two independent codes: Sierra/Fuego and LAMMPS. A suitable receiver model was then defined using a traditional continuum-based model for the air and a granular model for the particle curtain. A sensitivity study was executed using this model to determine the relevance of different granular model inputs on important quantities of interest in obstructed flow FPRs: the particle velocity and curtain opacity. The study showed that the granular model inputs had little effect on the particle velocity magnitude and curtain opacity after an obstruction.

Mills, Brantley↗
DOE OSTI2023

System efficiency of packed bed TES with radial flow vs. axial flow – Influence of aspect ratio

Here, this paper compares the net system efficiency, including thermal efficiency and pressure drop effects, of radial versus axial flow packed beds for thermal energy storage. The traditional packed bed system is a cylindrical geometry where fluid flows axially from one end to another. However, issues of thermal stratification and high-pressure drop have led to recent studies on radial flow systems. One potential benefit is the reduced pressure drop in a radial flow system. This paper compares the performance of radial flow and axial flow systems at a range of aspect ratios (AR = H/D bed ) from 0.21 to 1.92 using a numerical model where the storage volume is held constant in all cases. When the radial flow bed is at a low aspect ratio (short/wide), the thermal front is improved but the pressure drop is high. At a high aspect ratio, the velocity is reduced in radial flow, leading to decreased pressure drop but an increased spreads in the thermal front that lowers thermal efficiency. The opposite trends are noted in axial flow. Thermal efficiencies of 83–91 % were noted for radial flow, while they ranged from 85 to 94 % in axial flow. Net efficiencies including pressure drop ranged from 74 to 82 % for radial flow and 80–87 % for axial flow. In both systems, a peak net efficiency was noted between the highest and lowest aspect ratio. While some aspect ratios with radial flow outperform axial flow from a net efficiency perspective, the results show that the highest net efficiency from axial flow is higher than that from radial flow. Overall, this paper highlights the importance of innovative TES designs and their potential to improve energy efficiency.

25 ENERGY STORAGE↗
DOE OSTI2023

Particle Flow Distribution in a Fluidized-Particles Multitube Solar Receiver

A fluidized-particles two-tube solar receiver was tested at ambient temperature at PROMES Laboratory to investigate the influence of an inhomogeneous solar flux density on the particle mass flow rate between the tubes. The principle of this 3rd generation solar receiver is to fluidize the particles in a container, called dispenser, in which the tubes’ bottom are immersed. The fluidized particles are flowing upward the tubes by applying an overpressure in the dispenser. Air velocities are changed inside the tubes, thanks to air mass flow controllers, to represent temperature heterogeneity between the tubes. Air velocities from 0.05 up to 0.52 m/s were tested, both in homogeneous and heterogeneous conditions. In the heterogeneous ones, the differences in air velocity between the tubes aim to mimic a difference in temperature from 20 to 100 % with homogeneous air flow rates injected. The following conclusions were drawn. First, the particle mass flux in the tubes are the same with homogeneous air velocities, each one following a calibration map previously obtained. Second, different air velocities lead to different particle mass flux. Third, the rise of the total particle mass flux diminishes the pressure in the dispenser. Four, this diminution of pressure leads to a decrease of the particle mass flow rate of the tube with the lower air velocity. This influence can lead in some cases to the stop of the fluidized bed circulation in the affected tube.

Sahuquet, Guillaume (ORCID:0000000302752890)↗
DOE OSTI2023

High-resolution simulations of a turbulent boundary layer impacting two obstacles in tandem

High-fidelity large-eddy simulations of the flow around two rectangular obstacles are carried out at a Reynolds number of 10 000 based on the freestream velocity and the obstacle height. The incoming flow is a developed turbulent boundary layer. Mean-velocity components, turbulence fluctuations, and the terms of the turbulent-kinetic-energy budget are analyzed for three flow regimes: skimming flow, wake interference, and isolated roughness. Three regions are identified where the flow undergoes the most significant changes: the first obstacle’s wake, the region in front of the second obstacle, and the region around the second obstacle. In the skimming-flow case, turbulence activity in the cavity between the obstacles is limited and mainly occurs in a small region in front of the second obstacle. In the wake-interference case, there is a strong interaction between the freestream flow that penetrates the cavity and the wake of the first obstacle. Furthermore, this interaction results in more intense turbulent fluctuations between the obstacles. In the isolated-roughness case, the wake of the first obstacle is in good agreement with that of an isolated obstacle. Separation bubbles with strong turbulent fluctuations appear around the second obstacle.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Critical analysis of velocimetry methods for particulate flows from synthetic data

Particle tracking methods that extract high-fidelity particle velocity data from high speed video of particle laden flows is a common experimental technique applied to chemical processes. These measurements are used to better understand the motion of particles and fluids in complex systems and create data against which computational models are validated. However, the methods, codes, and experimental setups all have limitations. It is imperative that practitioners verify the methods and their implementation as well as understand the limitations of experimental setups. This work focuses on quantifying the visible depth of field in a high particle concentration fluidized bed. Following a precedent set by the particle imaging velocimetry community, a particle velocity field is manufactured using a computational fluid dynamics and discrete element method simulation. Photo realistic high-speed videos are rendered based on the simulated data using the three-dimensional creation software Blender. Particle velocities are extracted from the synthetic high-speed videos using three variants of Particle Tracking Velocimetry and Optical Flow Velocimetry methodologies. Here, the tracked results are then compared to the known solution, quantifying the error associated with the assumed visible depth. The results indicate that at depth of one particle diameter, all three particle tracking codes give accurate measurements, largely within 5%. However, the error increases when the full bed video measurements are compared to the known solution at one particle diameter, i.e., mimicking a validation study. Finally, for some statistics the constant depth assumption only increases the error slightly, for others significantly.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Understanding the role of flow dynamics in thermoacoustic combustion instability

Thermoacoustic combustion instability is one of the most challenging operational issues in several high-performance, low-emissions combustion technologies, including gas turbines, aircraft engines, rockets, and industrial boilers. Driven by the coupling between combustor acoustics and flame heat release rate fluctuations, thermoacoustic combustion instability can lead to reduced operability, increased emissions, and, in the most extreme cases, catastrophic failure of combustor components. The feedback loop between acoustics and combustion is often facilitated by fluid mechanic oscillations, referred to as “velocity coupling,” whereby acoustic oscillations drive flow fluctuations, which in turn create fluctuations in the flame. The character of these fluid mechanic oscillations is highly dependent on the structure of the flow field and the receptivity of the flow to external excitation. Combustor flow fields use features like fluid recirculation and shear to enhance flame holding and reduce emissions, but these are also the same features that can make the flow receptive to acoustic excitation or even drive self-excited oscillations. Here, in this paper, we discuss the basics of thermoacoustic instability with a focus on the role of hydrodynamic oscillations in typical combustor flows. To facilitate this discussion, we explore the hydrodynamic instability characteristics of several key combustor unit flows (wakes, swirling jets, etc.) and show how the hydrodynamic stability of a flow is an important consideration in determining a combustor’s propensity for thermoacoustic oscillations. Several examples of coupling between hydrodynamics and thermoacoustics are discussed to illustrate this important link. The paper concludes by discussing the potential for designing flow fields that are thermoacoustic instability resistant, either through a reduction in the receptivity of the flow or through nonlinear coupling mechanisms by which self-excited flow instabilities can suppress velocity-coupled combustion oscillations.

42 ENGINEERING↗
DOE OSTI2021

Spatially and Temporally Resolved Velocimetry for Hypersonic Flows

The development of new hypersonic flight vehicles is limited by the physical understanding that may be obtained from ground test facilities. This has motivated the present development of a temporally and spatially resolved velocimetry measurement for Sandia National Laboratories (SNL) Hypersonic Wind Tunnel (HWT) using Femtosecond Laser Electronic Excitation Tagging (FLEET). First, a multi-line FLEET technique has been created for the first time and tested in a supersonic jet, allowing simultaneous measurements of velocities along multiple profiles in a flow. Secondly, two different approaches have been demonstrated for generating dotted FLEET lines. One employs a slit mask pattern focused into points to yield a dotted line, allowing for two- or three-component velocity measurements free of contamination between components. The other dotted-line approach is based upon an optical wedge array and yields a grid of points rather than a dotted line. Two successful FLEET measurement campaigns have been conducted in SNL’s HWT. The first effort established optimal diagnostic configurations in the hypersonic environment based on earlier benchtop reproductions, including validation of the use of a 267 nm beam to boost the measurement signal-to-noise ratio (SNR) with minimal risk of perturbing the flow and greater simplicity than a comparable resonant technique at 202 nm. The same FLEET system subsequently was reconstituted to demonstrate the ability to make velocimetry measurements of hypersonic turbulence in a realistic flow field. Mean velocity profiles and turbulence intensity profiles of the shear layer in the wake of a hypersonic cone model were measured at several different downstream stations, proving the viability of FLEET as a hypersonic diagnostic.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Numerical Investigation of Butterfly Valve Performance in Variable Valve Sizes, Positions and Flow Regimes

Reliability and efficiency of valves are necessary for precise control and sufficient heat-flow to heat application plants for the integrated energy systems of nuclear power plants (NPPs). Strategic Management Analysis Requirement and Technology (SMART) valves’ ability to control flow and assess environmental parameters stands out for these requirements. Their ability to sustain the downstream flow rate, prevent reverse flow, and maintain pressure in the heat transport loop is much more efficient with the integration of sensors and intelligent algorithms. For assessing valve performance and monitoring, mechanical design and operating conditions are two important parameters. In this study, the butterfly valves of three different sizes are simulated with water and steam using STAR-CCM+ in various flow regimes and positions to analyze performance parameters to strategize an automated control system for efficiently balancing the heat–transport network. Also, flow behavior is studied using velocity and pressure fields for valve–body geometry optimization. It can be observed, through performance parameters, that the valves are suitable for operation between 30° and 90° positions with significantly low loss coefficients and high flow coefficients, and the performance parameters follow a certain pattern in both water and steam flow in each scenario.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

FreeMHD: Validation and verification of the open-source, multi-domain, multi-phase solver for electrically conductive flows

The extreme heat fluxes in the divertor region of tokamaks may require an alternative to solid plasma-facing components, for the extraction of heat and the protection of the surrounding walls. Flowing liquid metals are proposed as an alternative, but raise additional challenges that require investigation and numerical simulations. Free surface designs are desirable for plasma-facing components, but steady flow profiles and surface stability must be ensured to limit undesirable interactions with the plasma. Previous studies have mainly used steady-state, 2D, or simplified models for internal flows and have not been able to adequately model free-surface liquid metal (LM) experiments. Therefore, FreeMHD has been recently developed as an open-source magnetohydrodynamics (MHD) solver for free-surface electrically conductive flows subject to a strong external magnetic field. The FreeMHD solver computes incompressible free-surface flows with multi-region coupling for the investigation of MHD phenomena involving fluid and solid domains. The model utilizes the finite-volume OpenFOAM framework under the low magnetic Reynolds number approximation. FreeMHD is validated using analytical solutions for the velocity profiles of closed channel flows with various Hartmann numbers and wall conductance ratios. Next, experimental measurements are then used to verify FreeMHD, through a series of cases involving dam breaking, 3D magnetic fields, and free-surface LM flows. These results demonstrate that FreeMHD is a reliable tool for the design of LM systems under free surface conditions at the reactor scale. Furthermore, it is flexible, computationally inexpensive, and can be used to solve fully 3D transient MHD flows.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Stress effects on flow and transport in three-dimensional fracture networks

We investigate the effects of various external stress regimes on fracture apertures, fluid flow, and solute transport in three-dimensional fracture networks. We use well-established geomechanics equations coupled with discrete fracture network modeling to characterize changes in primary flow paths within a complex network as a function of stress magnitude and orientation. These changes manifest in the alterations of the fluid flow field and are measured in terms of Eulerian and Lagrangian flow observables including solute transport, which is a key problem in many hydrologic applications. Changes in primary flow paths affect the solute transport in the network by promoting anomalously early arrival or long tailing behavior. However, early time arrival is not ubiquitous in anisotropically stressed networks and in most cases there is a delayed arrival of solute, which is attributed to (i) the presence of low-velocity zones normal to the flow direction, (ii) the angle between flow direction and major compressive principal stress directions, and (iii) changes in the primary flow paths (i.e., increases in tortuosity and active network structure). Overall, flows become more channelized in anisotropically stressed fracture networks than in unstressed and isotropically stressed networks.

58 GEOSCIENCES↗