Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Definition of the unsteady vortex flow over a wing/body configuration

A problem of current interest in computational aerodynamics is the prediction of unsteady vortex flows over aircraft at high angles of attack. A six-month experimental effort was conducted at the John H. Harper Wind Tunnel to acquire qualitative and quantitative information on the unsteady vortex flow over a generic wing-body configuration at high angles of attack. A double-delta flat-plate wing with beveled edges was combined with a slender sharp-nosed body-of-revolution fuselage to form the generic configuration. This configuration produces a strong attached leading edge vortex on the wing, as well as sharply-peaked flow velocity spectra above the wing. While it thus produces flows with several well-defined features of current interest, the model was designed for efficiency of representation in computational codes. A moderate number of surface pressure ports and two unsteady pressure sensors were used to study the pressure distribution over the wing and body surface at high angles of attack; the unsteady pressure sensing did not succeed because of inadequate signal-to-noise ratio. A pulsed copper vapor laser sheet was used to visualize the vortex flow over the model, and vortex trajectories, burst locations, mutual induction of vortex systems from the forebody, strake, and wing, were quantified. Laser Doppler velocimetry was used to quantify all 3 components of the time-average velocity in 3 data planes perpendicular to the freestream direction. Statistics of the instantaneous velocity were used to study intermittency and fluctuation intensity. Hot-film anemometry was used to study the fluctuation energy content in the velocity field, and the spectra of these fluctuations. In addition, a successful attempt was made to measure velocity spectra, component by component, using laser velocimetry, and these were compared with spectra measured by hot-film anemometry at several locations.

Liou, S. G.↗
NASA NTRS1930

Flow and Force Equations for a Body Revolving in a Fluid

Part I gives a general method for finding the steady-flow velocity relative to a body in plane curvilinear motion, whence the pressure is found by Bernoulli's energy principle. Integration of the pressure supplies basic formulas for the zonal forces and moments on the revolving body. Part II, applying this steady-flow method, finds the velocity and pressure at all points of the flow inside and outside an ellipsoid and some of its limiting forms, and graphs those quantities for the latter forms. Part III finds the pressure, and thence the zonal force and moment, on hulls in plane curvilinear flight. Part IV derives general equations for the resultant fluid forces and moments on trisymmetrical bodies moving through a perfect fluid, and in some cases compares the moment values with those found for bodies moving in air. Part V furnishes ready formulas for potential coefficients and inertia coefficients for an ellipsoid and its limiting forms. Thence are derived tables giving numerical values of those coefficients for a comprehensive range of shapes.

Zahm, A F↗
NASA NTRS1997

Planar Doppler Velocimetry for Large-Scale Wind Tunnel Testing

Recently, Planar Doppler Velocimetry (PDV) has been shown by several laboratories to offer an attractive means for measuring three-dimensional velocity vectors everywhere in a light sheet placed in a flow. Unlike other optical means of measuring flow velocities, PDV is particularly attractive for use in large wind tunnels where distances to the sample region may be several meters, because it does not require the spatial resolution and tracking of individual scattering particles or the alignment of crossed beams at large distances. To date, demonstrations of PDV have been made either in low speed flows without quantitative comparison to other measurements, or in supersonic flows where the Doppler shift is large and its measurement is relatively insensitive to instrumental errors. Moreover, most reported applications have relied on the use of continuous-wave lasers, which limit the measurement to time-averaged velocity fields. This work summarizes the results of two previous studies of PDV in which the use of pulsed lasers to obtain instantaneous velocity vector fields is evaluated. The objective has been to quantitatively define and demonstrate PDV capabilities for applications in large-scale wind tunnels that are intended primarily for the production testing of subsonic aircraft. For such applications, the adequate resolution of low-speed flow fields requires accurate measurements of small Doppler shifts that are obtained at distances of several meters from the sample region. The use of pulsed lasers provides the unique capability to obtain not only time-averaged fields, but also their statistical fluctuation amplitudes and the spatial excursions of unsteady flow regions such as wakes and separations. To accomplish the objectives indicated, the PDV measurement process is first modeled and its performance evaluated computationally. The noise sources considered include those related to the optical and electronic properties of Charge-Coupled Device (CCD) arrays and to speckle effects associated with coherent illumination from pulsed lasers. The signal noise estimates are incorporated into the PDV signal analysis process and combined with computed scattering signals using a Mie scattering theory for polydisperse smoke particles. The relevant parameters incorporate a range of practical aerodynamic test conditions and facility sizes. The results define the optimum instrument configurations, show that the expected signal levels from a practical PDV system are sufficiently large to allow its useful application in large facilities, and show that the expected velocity measurement uncertainties are small compared to the mean velocities of interest for most subsonic, large-scale wind tunnel testing. Experimental studies using several experimental bench-top setups are then described that validate the physics of the PDV model and to calibrate its computed results. The validated model allows estimates of the uncertainties of PDV measurements and a complete definition of the PDV capabilities to be made with sufficient confidence to decide the viability of PDV for large-scale wind tunnel applications.

McKenzie, Robert L.↗
NASA NTRS1997

Measurement Capabilities of Planar Doppler Velocimetry in Large-Scale Wind Tunnels

Over the past few years, Planar Doppler Velocimetry (PDT) has been shown by several laboratories to offer an attractive means for measuring three-dimensional velocity vectors everywhere in a light sheet placed in a flow. Unlike some other optical means of measuring flow velocities, PDT is particularly attractive for use in large wind tunnels where distances to the sample region may be several meters, because it does not require the spatial resolution and tracking of individual scattering particles or the alignment of crossed beams at large distances. To date, demonstrations of PDT (also called Doppler Global Velocimetry by some authors) have been made either in low speed flows without quantitative comparison to other measurements, or in supersonic flows where the Doppler shift is large and its measurement is relatively insensitive to instrumental errors. Moreover, most reported applications have relied on the use of continuous-wave lasers, which limit the measurement to time-averaged velocity fields. This work summarizes the results of two previous studies of PDT in which the use of pulsed lasers to obtain instantaneous velocity vector fields is evaluated. The objective has been to quantitatively define and demonstrate PDT capabilities for applications in large-scale wind tunnels that are intended primarily for the testing of rotorcraft and subsonic aircraft at speeds typically less than 100 m/s. For such applications, the adequate resolution of low-speed flow fields requires accurate measurements of small Doppler shifts that are obtained at distances of several meters from the sample region and with a field of view that is sufficient to encompass the entire region of interest. The use of pulsed lasers provides the unique capability to obtain not only time-averaged fields, but also their statistical fluctuation amplitudes and the spatial excursions of unsteady flow regions such as wakes, separations, and rotor-tip vortices. To accomplish the objectives of these studies, the PDT measurement process was first modeled and its performance evaluated computationally. The noise sources considered included those related to the optical and electronic properties of Charge-Coupled Device (CCD) arrays and to speckle effects associated with the coherent illumination of aerosols from pulsed lasers. The signal noise estimates were incorporated into the PDT signal analysis process and combined with computed scattering signals using a Mae scattering theory for a distributed range of aerosol particle sizes. The results are used to define the necessary instrument configuration, to show that the expected signal levels from a practical PDT system are sufficiently large to allow its useful application in large facilities, and to show that the expected velocity measurement uncertainties are small compared to the mean velocities of interest for most subsonic, large-scale wind tunnel testing, Experimental studies using several bench-top setups are then described that validate the physics of the PDT model and demonstrate the ability to obtain accurate PDT measurements using procedures that are compatible with large-scale wind tunnel operations. The PDT measurement capabilities found in this study lead to the conclusion that PDT offers significant advantages compared to other means of measuring velocity fields in large-scale wind tunnels, including those operating at low speeds.

McKenzie, Robert L.↗
NASA NTRS1980

Resonant Doppler velocimeter

A technique is presented for visualizing and quantitatively measuring velocity, temperature, and pressure by shining a single frequency laser beam into a gaseous flow which is seeded with an atomic species. The laser is tuned through the absorption frequencies of the seeded species and the absorption profile is detected by observing fluorescence as the atoms relax back to the ground state. The flow velocity is determined by observing the Doppler shift in the absorption frequency. Spectroscopic absorption line broadening mechanisms furnish information regarding the static temperature and pressure of the moving gas. Results of experiments conducted in the free stream and in the bow shock of a conical model mounted in a hypersonic wind tunnel indicate that the experimental uncertainties in the measurement of average values for the velocity, temperature and pressure of the flow are 0.1, 5 and 10 percent respectively.

Zimmermann, M.↗
NASA NTRS1981

Measuring molecular flows with high-resolution stimulated Raman spectroscopy

It is proposed to use high-resolution stimulated Raman spectroscopy to directly measure high-speed molecular flow velocities in wind tunnels and in combustive chambers. A feasibility study indicates that flow speeds from Mach 0.04 up may be measured with the proposed method using available laser systems. It is pointed out that the success of the proposed technique will make it possible to measure all interesting flow parameters, i.e., species concentration, temperature, and velocity, in a time of less than 1 microsecond at a repetition rate of 10,000/s using a single experimental arrangement.

She, C. Y.↗
NASA NTRS1975

Airframe noise measurements on a transport model in a quiet flow facility

An experimental investigation was conducted in an anechoic flow facility to explore problems and methods of measuring the airframe (nonpropulsive) noise associated with a 1/20-scale model of a B-737 transport. The test model geometry simulated the cruise and a landing configuration. Nonpropulsive model noise was detected at various flow velocities and at various angles of attack when turbulent flow was induced over the model. Discrete tones, associated with the extended undercarriage and wheel cavities, and an increase in broadband sound pressure level were observed with the model in a landing configuration.

Shearin, J. G.↗
NASA NTRS1978

Laser-velocimeter surveys of merging vortices in a wind tunnel

The merger of two vortices was studied with a laser velocimeter designed to measure the two cross-stream components of velocity. Measurements were made at several downstream distances in the vortex wake shed by two semispan wings mounted on the wind tunnel walls. The velocity data provided well difined contours of cross-flow velocity, stream function and vorticity. Downstream of the merger point the vorticity was shown to be independent of the downstream distance for small radii, and at larger radii was dependent on the distance from the wing rather than from the merger point. Upstream of the merger point a multicell vorticity pattern was shown.

Corsiglia, V. R.↗
NASA NTRS1986

Convection zone origins of solar atmospheric heating

Spicules are examined as a means for supplying the corona with mass, energy, and magnetic field. It is suggested that spicules form from the supersonic upward expansion of material on nearly evacuated network flux tubes embedded within the sun's convection zone. This allows supersonic but subescape velocities to be attained by the material as it flows outward through the photosphere. Although supersonic, the kinetic energy (subescape) of the spicule material, as observed, is insufficient for coronal heating. It is suggested that, through buoyancy changes on evacuated flux tubes, the magnetic field first 'wicks' material flow into the solar atmosphere. Subsequently, the magnetic field energizes the gaseous material to form the conventional hot, dynamically expanding, solar corona. This occurs through momentum and energy transport by Alfven waves and associated Maxwell stresses concurrently flowing upward on these 'geysers' (spicules). The vertical momentum equation governing fluid flow is examined, and a particular equipartition solution is presented for the flow velocity along a simple field geometry.

Schatten, Kenneth H.↗
NASA NTRS2002

UAH Analysis of TIDE/PSI Data for ISTP Solar Maximum Extended Mission

During the course of this research, several investigations have been carried out at both high and low altitudes. The low altitude studies are those associated with perigee observations of ion field-aligned flows measured by POLAR/TIDE near 5000 km altitude. High altitude studies employed ion observations near apogee (above 6 R(sub E) geocentric). In both cases the observations occur at high latitudes, in or near the polar regions: the southern polar region for the low altitude studies and the northern polar region for the high altitude studies. A study of the relationship between field-aligned flow velocities, fluxes, and densities to convection speeds was published in the Journal of Atmospheric and Terrestrial Physics . Here we have demonstrated an anti-correlation between the 0+ densities and the convection speeds, and a correlation between the parallel upward velocities and the convection speeds, and have discussed these results as being compatible with the Cleft Ion Fountain concept for supplying O(sup +) ions to the polar cap magnetosphere. Another topic investigated was the relationship between TIDE-observed upward and downward parallel O(sup +) bulk velocities near 5000 km altitude over the southern polar regions, and near-simultaneous auroral observations by the Ultra-Violet Imager. We have prepared several overlaid plots of such auroral images across an MLT-ILAT dial plot of the polar regions with upward and downward velocities, as well as other parameters such as ion densities and fluxes. The overlaid plots show quite nicely how upward velocities and crossovers between upward and downward velocities occur in association with auroral forms, while downward flows are associated with dark regions of the polar cap.

Comfort, Richard H.↗
NASA NTRS2017

Flow Cage Assemblies

Apparatus, systems and methods for implementing flow cages and flow cage assemblies in association with high pressure fluid flows and fluid valves are provided. Flow cages and flow assemblies are provided to dissipate the energy of a fluid flow, such as by reducing fluid flow pressure and/or fluid flow velocity. In some embodiments the dissipation of the fluid flow energy is adapted to reduce erosion, such as from high-pressure jet flows, to reduce cavitation, such as by controllably increasing the flow area, and/or to reduce valve noise associated with pressure surge.

Sherrit, Stewart↗
NASA NTRS1974

Theoretical surface velocity distributions on acoustic splitter geometries for an engine inlet

The potential-flow velocity distributions on several splitter geometries in an engine inlet and their variation with different splitter leading-edge shapes and distances from the inlet highlight were analyzed. The velocity distributions on the inner and outer surfaces of the splitters are presented for low-speed and cruise conditions. At zero incidence angle, the splitter with the 4-to-1 elliptical leading edge had lower peak velocities and velocity gradients than the splitter with the 2-to-1 elliptical leading edge. The velocity gradients decreased as the distance from the inlet highlight to the splitter leading edge was increased. For a given distance, the peak velocity on the splitter inner surface increased with increasing inlet incidence angle. At an incidence angle of 50 deg, the velocity level and gradients on the inner surface of the splitter in the forward position were sufficiently severe to suggest local separation.

Albers, J. A.↗
NASA NTRS1980

Flow measurements in a model swirl combustor

Flow measurements in a model combustor composed of two confined coaxial swirling jets under noncombusting conditions are presented. Mean flow results are obtained for five different flow conditions to determine the effect of outer swirl on the recirculation zone (which is used for flame stabilization under combustion conditions). As the outer swirl magnitude is first decreased from maximum counter-swirl to zero and then increased to give co-swirl conditions, the size and the reverse flow velocity in the recirculation zone diminish. Detailed time mean and fluctuating flow measurements are obtained for a co-swirl and a counter-swirl condition with a directional pitot probe and hot-wire anenometry. For these two cases, recirculation zone occurs only with counter-swirl, near the exit of the inner jet. The recirculation zone is in the form of a one celled toroidal vortex having very low swirl velocity. Axial development of fluctuation levels, energy dissipation rates and turbulence length scales are described for the two flow conditions. Spectral analysis reveals periodic oscillations in both flows. The oscillations originate from the inner jet and up to 4 harmonics are observed. The fundamental frequencies are comparable to the rotational frequencies of the inner jets at the exit which are approximately under solid body rotation. The significance of the present results for the combustion process is discussed.

Vu, B. T.↗
NASA NTRS2012

Experimental Study of Boundary Layer Flow Control Using an Array of Ramp-Shaped Vortex Generators

The objective of this study was to obtain a database on the flowfield past an array of vortex generators (VGs) in a turbulent boundary layer. All testing was carried out in a low speed wind tunnel with a flow velocity of 29 ft/sec, giving a Reynolds number of 17,500 based on the width of the VG. The flowfield generated by an array of five ramp-shaped vortex generators was examined with hot wire anemometry and smoke flow visualization. The magnitude and extent of the velocity increase near the wall, the penetration of the velocity deficit into the core flow, and the peak streamwise vorticity are examined. Influence of various parameters on the effectiveness of the array is considered on the basis of the ability to pull high momentum fluid into the near wall region.

Hirt, Stefanie M.↗
NASA NTRS1979

Flow and Force Equations for a Body Revolving in a Fluid

A general method for finding the steady flow velocity relative to a body in plane curvilinear motion, whence the pressure is found by Bernoulli's energy principle is described. Integration of the pressure supplies basic formulas for the zonal forces and moments on the revolving body. The application of the steady flow method for calculating the velocity and pressure at all points of the flow inside and outside an ellipsoid and some of its limiting forms is presented and graphs those quantities for the latter forms. In some useful cases experimental pressures are plotted for comparison with theoretical. The pressure, and thence the zonal force and moment, on hulls in plane curvilinear flight are calculated. General equations for the resultant fluid forces and moments on trisymmetrical bodies moving through a perfect fluid are derived. Formulas for potential coefficients and inertia coefficients for an ellipsoid and its limiting forms are presented.

Zahm, A. F.↗
DOE OSTI2021

Wave-kinetic approach to zonal-flow dynamics: recent advances

Basic physics of drift-wave turbulence and zonal flows has long been studied within the framework of wave-kinetic theory. Recently, this framework has been re-examined from first principles, which has led to more accurate yet still tractable "improved" wave-kinetic equations. In particular, these equations reveal an important effect of the zonal-flow "curvature" (the second radial derivative of the flow velocity) on dynamics and stability of drift waves and zonal flows. We overview these recent findings and present a consolidated high-level picture of (mostly quasilinear) zonal-flow physics within reduced models of drift-wave turbulence.

fusion plasmas↗
NASA NTRS1985

Prediction of the flow-field interference induced by the long-range laser velocimeter in the Ames 40- by 80-foot and the 80- by 120-foot wind tunnels

The predicted flow disturbances induced in the test sections of the Ames 40- by 80-Foot Wind Tunnels by the presence of the Long-Range Laser Velocimeter (LRLV) are presented. The predictions were made using a potential-flow paneling code to model the test section and the LRLV, and a calculation of the resulting flow field was made. The flow velocity and angularity were calculated at numerous locations in the flow field relative to the LRLV, and the results are presented.

Reinath, M. S.↗
NASA NTRS1994

MHD simulations of boundary layer formation along the dayside Venus ionopause due to mass loading

A two-dimensional magnetohydrodynamic (MHD) simulation of mass-loaded solar wind flow around the dayside of Venus is presented. For conditions appropriate to a low-altitude ionopause the simulations show that mass loading from the pickup of oxygen ions produces a boundary layer of finite thickness along the ionopause. Within this layer the temperatures exhibit strong gradients normal to and away from the ionopause. Furthermore, there is a shear in the bulk flow velocity across the boundary layer, such that the (predominantly tangential) flow decreases in speed as the ionopause is approached and remains small along the ionopause, consistent with Pioneer Venus observations. The total mass density increases significantly as the flow approaches the ionopause, where the contribution of O(+) to the total number density is a few percent. Numerical simulations are carried out for various mass addition rates and demonstrate that the boundary layer develops when oxygen ion production exceeds approximately 2 x 10(exp 5)/cu m/s. For the upstream solar wind parameters and mass loading rates chosen for these simulations, the results are consistent with observations made on the dayside of Venus for average ionopause conditions near 300 km.

Mcgary, J. E.↗