SEARCH · Engineering Papers

Results for “floating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Morphological instability in a float zone

This paper examines the morphological instability of the freezing interface of the float zone in a crystal sheet for which the height of the liquid zone L = Lf + Lm (where Lf and Lm are the planar positions of the solidifying and melting interfaces) is smaller than the width and the thickness of the sheet. The Lf and Lm positions are calculated, and basic state concentration profiles are determined for a planar interfacial system. A linear stability analysis of this system is performed showing that the growth rate of disturbances is a modified version of the growth rate for a directional solidification system. It was found that shorter melt zone configurations are less susceptible to long wavelength morphological instability, indicating that, to suppress morphological instability in a float zone system, it is necessary to decrease the liquid zone height.

Humphreys, Laura B.↗

NASA NTRS1990

A half-zone study of Marangoni convection in floating-zone crystal growth under microgravity

Floating-zone crystal growth under microgravity, though free from natural convection, can still be susceptible to Marangoni convection. The use of a ring heater in contact with most of the surface of the melt zone, has recently been considered as one way of reducing Marangoni convection in the melt zone. In order to study Marangoni convection in the melt zone in this modified floating-zone crystal growth process, a half-zone system was adopted. Computer simulation and direct observation of Marangoni convection in the half-zone system were carried out for two different cases. In the first case, the surface of the melt zone was completely free, while in the second it was mostly in contact with a quartz ring. The results of computer simulation and direct observation both indicated that in the second case Marangoni convection was significantly reduced near the melt/solid interface as well as in the bulk melt.

Lan, C. W.↗

NASA NTRS1991

On the nature of control algorithms for free-floating space manipulators

It is suggested that nearly any control algorithm that can be used for fixed-based manipulators also can be employed in the control of free-floating space manipulator systems, with the additional conditions of estimating or measuring a spacecraft's orientation and of avoiding dynamic singularities. This result is based on the structural similarities between the kinematic and dynamic equations for the same manipulator but with a fixed base. Barycenters are used to formulate the kinematic and dynamic equations of free-floating space manipulators. A control algorithm for a space manipulator system is designed to demonstrate the value of the analysis.

Papadopoulos, Evangelos↗

NASA NTRS1992

Numerical simulations of inductive-heated float-zone growth

The present work provides an improved fluid flow and heat-transfer modeling of float-zone growth by introducing a RF heating model so that an ad hoc heating temperature profile is not necessary. Numerical simulations were carried out to study the high-temperature float-zone growth of titanium carbide single crystal. The numerical results showed that the thermocapillary convection occurring inside the molten zone tends to increase the convexity of the melt-crystal interface and decrease the maximum temperature of the molten zone, while the natural convection tends to reduce the stability of the molten zone by increasing its height. It was found that the increase of induced heating due to the increase of applied RF voltage is reduced by the decrease of zone diameter. Surface tension plays an important role in controlling the amount of induced heating. Finally, a comparison of the computed shape of the free surface with a digital image obtained during a growth run showed adequate agreement.

Chan, Y. T.↗

NASA NTRS1990

Accurate GPS measurement of the location and orientation of a floating platform

This article describes the design and initial tests of the GPS portion of a system for making seafloor geodesy measurements. In the planned system, GPS antennas on a floating platform will be used to measure the location of an acoustic transducer, attached below the platform, which interrogates an array of transponders on the seafloor. Since the GPS antennas are necessarily some distance above the transducer, a short-baseline GPS interferometer consisting of three antennas is used to measure the platform's orientation. A preliminary test of several crucial elements of the system was performed. The test involved a fixed antenna on the pier and a second antenna floating on a buoy about 80 m away. GPS measurements of the vertical component of this baseline, analyzed independently by two groups using different software, agree with each other and with an independent measurement within a centimeter. The first test of an integrated GPS/acoustic system took place in the Santa Cruz Basin off the coast of southern California in May 1990. In this test a much larger buoy, designed and built at SIO, was equipped with three GPS antennas and an acoustic transducer that interrogated a transponder on the ocean floor. Preliminary analysis indicates that the horizontal position of the transponder can be determined with a precision of about a centimeter.

Purcell, G. H., Jr.↗

NASA NTRS1930

The Effect of Wing Tip Floating Ailerons on the Autorotation of a Monoplane Wing Model

The preliminary tests described here were made to determine the extent to which wing tip floating ailerons might be effective in reducing airplane spinning tendencies. The tests showed that initial spinning tendencies and rates of stable spinning could doubtless be reduced by the use of tip floating ailerons on an airplane. It also appears to be desirable to reduce to a minimum the interference between wing and aileron. This would serve to maintain uniformity of action at all angles of attack and enable calculation of the aileron characteristics.

Knight, Montgomery↗

NASA NTRS1939

Hydrodynamic and Aerodynamic Tests of a Family of Models of Seaplane Floats with Varying Angles of Dead Rise - N.A.C.A. Models 57-A, 57-B, and 57-C

Three models of V-bottom floats for twin-float seaplanes (N.A.C.A. models 57-A, 57-B, and 57-C) having angles of dead rise of 20 degrees, 25 degrees, and thirty degrees, respectively, were tested in the N.A.C.A. tank and in the N.A.C.A. 7- by 10-foot wind tunnel. Within the range investigated, the effect of angle of dead rise on water resistance was found to be negligible at speeds up to and including the hump speed, and water resistance was found to increase with angle of dead rise at planing speeds. The height of the spray at the hump speed decreased with increase in angle of dead rise and the aerodynamic drag increased with dead rise. Lengthening the forebody of model 57-B decreased the water resistance and the spray at speeds below the hump speed. Spray strips provided an effective means for the control of spray with the straight V sections used in the series but considerably increased the aerodynamic drag. Charts for the determination of the water resistance and the static properties of the model with 25 degrees dead rise and for the aerodynamic drag of all the models are included for use in design.

Parkinson, John B↗

NASA NTRS1927

Tests on airplane fuselages, floats and hulls

This report is a compilation of test data on airplane fuselages, nacelles, airship cars, seaplane floats, and seaplane hulls, prepared by the Bureau of Aeronautics, at the requests of the National Advisory Committee for Aeronautics. The discussion of the data includes the derivation of a scale correction curve to be used in obtaining the full scale drag. Composite curves of drag and L/D for floats and hulls are also given. (author)

Diehl, Walter S↗

NASA NTRS1929

Water-Pressure Distribution on Seaplane Float

The investigation presented in this report was conducted for the purpose of determining the distribution and magnitude of water pressures likely to be experienced on seaplane hulls in service. It consisted of the development and construction of apparatus for recording water pressures lasting one one-hundredth second or longer and of flight tests to determine the water pressures on a UO-1 seaplane float under various conditions of taxiing, taking off, and landing. The apparatus developed was found to operate with satisfactory accuracy and is suitable for flight tests on other seaplanes. The tests on the UO-1 showed that maximum pressures of about 6.5 pounds per square inch occur at the step for the full width of the float bottom. Proceeding forward from the step the maximum pressures decrease in magnitude uniformly toward the bow, and the region of highest pressures narrows toward the keel. Immediately abaft the step the maximum pressures are very small, but increase in magnitude toward the stern and there once reached a value of about 5 pounds per square inch. (author)

Thompson, F L↗

NASA NTRS1938

A Flight Comparison of Conventional Ailerons on a Rectangular Wing and of Conventional and Floating Wing-Tip Ailerons on a Tapered Wing

Report presents the results of flight tests comparing the relative effectiveness of conventional ailerons of the same size on wings of rectangular and tapered plan forms made with a Fairchild 22 airplane. Information is included comparing conventional and floating wing-tip ailerons on a tapered wing. The results showed that the conventional ailerons were somewhat more effective on the tapered than on the rectangular wing. The difference, however, was so small as to be imperceptible to the pilots. The floating wing-tip ailerons were only half as effective as the conventional ailerons and, for this reason, were considered unsatisfactory.

Soule, H A↗

NASA NTRS1944

Experimental Verification of the Rudder-Free Stability Theory for an Airplane Model Equipped with Rudders Having Negative Floating Tendency and Negligible Friction

An investigation has been made in the Langley free-flight tunnel to obtain an experimental verification of the theoretical rudder-free stability characteristics of an airplane model equipped with conventional rudders having negative floating tendencies and negligible friction. The model used in the tests was equipped with a conventional single vertical tail having rudder area 40 percent of the vertical tail area. The model was tested both in free flight and mounted on a strut that allowed freedom only in yaw. Tests were made with three different amounts of rudder aerodynamic balance and with various values of mass, moment of inertia, and center-of-gravity location of the rudder. Most of the stability derivatives required for the theoretical calculations were determined from forced and free-oscillation tests of the particular model tested. The theoretical analysis showed that the rudder-free motions of an airplane consist largely of two oscillatory modes - a long-period oscillation somewhat similar to the normal rudder-fixed oscillation and a short-period oscillation introduced only when the rudder is set free. It was found possible in the tests to create lateral instability of the rudder-free short-period mode by large values of rudder mass parameters even though the rudder-fixed condition was highly stable. The results of the tests and calculation indicated that for most present-day airplanes having rudders of negative floating tendency, the rudder-free stability characteristics may be examined by simply considering the dynamic lateral stability using the value of the directional-stability parameter Cn(sub p) for the rudder-free condition in the conventional controls-fixed lateral-stability equations. For very large airplanes having relatively high values of the rudder mass parameters with respect to the rudder aerodynamic parameters, however, analysis of the rudder-free stability should be made with the complete equations of motion. Good agreement between calculated and measured rudder-free stability characteristics was obtained by use of the general rudder-free stability theory, in which four degrees of lateral freedom are considered. When this assumption is made that the rolling motions alone or the lateral and rolling motions may be neglected in the calculations of rudder-free stability, it is possible to predict satisfactorily the characteristics of the long-period (Dutch roll type) rudder-free oscillation for airplanes only when the effective-dihedral angle is small. With these simplifying assumptions, however, satisfactory prediction of the short-period oscillation may be obtained for any dihedral. Further simplification of the theory based on the assumption that the rudder moment of inertia might be disregarded was found to be invalid because this assumption made it impossible to calculate the characteristics of the short-period oscillations.

STABILITY- FAIRCHILD R2K-1↗

NASA NTRS1942

Strength Tests on Hulls and Floats

The present report deals with strength tests on hulls and floats intended in part for the collection of construction data for the design of these components and in part for the stress analysis of the finished hulls and floats.

Matthaes, K↗

NASA NTRS1937

The Scale Effect in Towing Tests with Airplane-float Systems

The present report includes a description of the making of three-component measurements on a full-size float mounted on an actual airplane and the comparison of the results with those from two models of the same form but of different size which had been tested in the towing tank. The purpose of the comparison is to determine the effect of the Reynolds Number on the results of model tank tests. Following a brief discussion of previous tests intended to elucidate the problem of scale effect on float systems and a description of the testing equipment, the choice of the reference quantities to be used in the comparison is discussed. The selection of load, speed, and trim as a basis of comparison seems best suited to the practical operation of making this comparison. The quantities affected by scale are then: resistance, trimming moment, and their derivatives; planing number (resistance/weight on water); and position of center of pressure.

Schmidt, Rudolph↗

NASA NTRS1936

The impact on floats or hulls during landing as affected by bottom width

For floats and hulls having V bottoms the impact force does not necessarily increase with increasing width. Therefore, the weight of the float landing gear, side walls, and other parts, and of the fuselage construction need not be increased with increasing bottom width, but the weight of the bottom construction itself, on the other hand, does not increase with increase in bottom width and is largely determined by the type of construction.

Mewes, E↗

NASA NTRS1935

Hydrodynamic Tests of Models of Seaplane Floats

This report contains the results of tank tests carried out at free trim on seventeen hulls and floats of various types. The data as to the weight on water, trim, and relative resistance for each model are plotted nondimensionally and are referenced both to the total weight and to the weight on water. Despite the fact that the experiments were not made systematically, a study of the models and of the test data permits nevertheless some general deductions regarding the forms of floats and their resistance. One specific conclusion is that the best models have a maximum relative resistance not exceeding 20 percent of the total weight.

Eula, Antonio↗

NASA NTRS1994

Floating Vacuum Skimmer For Emulsion Cleaning

Floating skimmer, when connected to wet/dry vacuum cleaner and placed on surface of liquid in emulsion cleaning tank, draws off floating emulsified residue. Eliminates need for tedious operation.

Morgan, Gene E.↗

NASA NTRS1993

Computer-controlled float zone crystal growth

A PC-based computer control system to automate a high-temperature float zone growth of titanium carbide is reported. The control strategy of the computer control system relies on the relations derived from a combination of empirical relations and results from detailed mathematical analysis of the physical transports of the entire float zone assembly. A system control computer program was written to establish real-time determination of the size of the molten zone from a thermal image, control parameters from established relationships, and collected processed data to achieve control objectives. We found that the developed computer control allows the growth process to be operated nearer the stability limit. Any slight variations in growth conditions can be corrected in time to avoid any instability growth, which otherwise cannot be adjusted via manual control.

Chan, Y. T.↗

NASA NTRS1994

Thermocapillary convection in floating zones under simulated reduced-gravity conditions

The present study demonstrated that calculated thermocapillary convection in a non-cylindrical floating zone can now be compared with measured one, by considering the lens effect of the floating zone. Flow visualization and computer simulation of thermocapillary convection in a silicone oil zone and a molten zone in an NaNO3 rod were conducted. The calculated results agree very well with the measured ones, including the free surface shapes, the solid/melt interface shapes and the velocity fields.

Tao, Y.↗