Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fast”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Integral Measurement of the 237 Np($n$, γ) 238 Np Cross Section with Fast Neutrons

Accurate knowledge of the 237 Np($n$; γ) 238 Np cross section at fast neutron energies is important for applied nuclear science. The presently available experimental data has large disagreements in the fast neutron region. A measurement of the 237 Np($n$; γ) 238 Np cross section was performed using a well characterized fast neutron source and the results was compared with previous measurements and current nuclear data evaluations. This will provide an integral measurement that can be used as a benchmark for current evaluations. Multiple samples of 237 Np were irradiated in the Godiva-IV critical assembly. Following the irradiation, the samples placed in a γ-ray counting setup and the γ-rays emitted from the decay of 238 Np were measured over a time period of approximately 7 days. Multiple γ-ray decay branches of 238 Np were observed. The observed activity of 238 Np was used to calculate the amount of 238 Np produced during the irradiation via the 237 Np($n$; γ) 238 Np and an integral cross section of 359(10) mb was measured. The 238 Np half-life has been measured with a result of 50.34(7) hours. An integral measurement of the 237 Np($n$; γ) 238 Np cross section has been measured. This result has been compared to the calculated integral cross section using the ENDF/BVIII.0 and JENDL-4.0 evaluated cross sections and found to be in good agreement with ENDF/BVIII.0 value of 367 mb. The JENDL-4.0 evaluation yields a value of 312 mb, which is significantly lower than the measured cross section.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Fast faraday cup for measuring the longitudinal distribution of particle charge density in non-relativistic beams

A Fast Faraday Cup includes a group of electrodes including a grounded electrode having a through hole and a collector electrode configured with a blind hole that functions a collector hole. The electrodes are configured to allow a beam (e.g., a non-relativistic beam) to fall onto the grounded electrode so that the through hole cuts a beamlet that flies into the collector hole and facilitates measurement of the longitudinal distribution of particle charge density in the beam. The diameters, depths, spacing and alignment of the collector hole and the through hole are controllable to enable the Fast Faraday day cup to operate with a fast response time (e.g., fine time resolution) and capture secondary particles.

Sun, Ding↗
DOE OSTI2023

Comparison of FAST Experiments to BISON Simulations

The Fission Accelerated Steady-State Test (FAST) experiments utilize the effects of scaling to accelerate the burnup experienced by the fuel. This experimental technique offers a unique opportunity to evaluate the effects of scaling on fuel and cladding material modelling. Currently, models used in the BISON fuel performance code for metallic fuel performance are calibrated for EBR-II conditions and geometries. Comparing BISON simulations to FAST experimental data will allow for the identification of shortcomings in the models for conditions outside the EBR-II paradigm. FAST experiments have been performed on U-Zr and U-10Mo fuel types with HT9 cladding. Initial comparisons of simulated cladding strains to experimental results show that the BISON simulations consistently overpredict cladding strain in the fuel region but underpredict the cladding strain in the plenum region. This indicates potential issues with the simulation of swelling and gas pressure at smaller geometries. Further comparison with fission gas release measurements is planned as data becomes available.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

A High-Precision, Fast, Robust, and Cost-Effective Muon Detector Concept for the FCC-ee

We propose a high-precision, fast, robust and cost-effective muon detector concept for an FCC-ee experiment. This design combines precision drift tubes with fast plastic scintillator strips to enable both spatial and timing measurements. The drift tubes deliver two-dimensional position measurements perpendicular to the tubes with a resolution around 100~$\mu$m. Meanwhile, the scintillator strips, read out with the wavelength-shifting fibers and silicon photomultipliers, provide fast timing information with a precision of 200~ps or better and measure the third coordinate along the tubes with a resolution of about 1~mm.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2026

Assembly Bowing Reactivity Calculation Methodology Applied to Lead Fast Reactor

Ducted assemblies bow during operation due to power and temperature gradients which can be influenced by operating flow rates. For fast spectrum cores using ducted assemblies, the bowing behavior follows that of the duct and because there are gaps between the ducts, the bowing can result in compaction or expansion of the active core. This local displacement can have a positive or negative impact and knowing the net effect during transients is important for system reactivity control. Keeping the net bowing reactivity worth low is possible with attentive placement of load pads above the active core and selecting load pad gap thicknesses that result in a desired behavior at standard operating conditions. This paper considers a Lead Fast Reactor (LFR) concept fueled by HALEU UO2 developed by Westinghouse Electric Company (WEC) and applies a workflow of Argonne-developed codes to estimate the core bowing reactivity worth. Using orifice flow rates grouped by assembly type, the net reactivity impact due to core assembly bowing for the LFR was found to be small and in line with other liquid metal fast reactors: +29/+32/+35 pcm, or about +$0.049/+$0.055/+$0.059, for BOEC/MOEC/EOEC, respectively.

bowing reactivity↗
DOE OSTI2023

Fast All-sky Radiation Model for Solar applications (FARMS) 2023 [SWR-16-18]

The Fast All-sky Radiation Model for Solar applications (FARMS) is used to compute cloudy irradiance. Radiative transfer (RT) models simulating broadband solar radiation have been widely used by atmospheric scientists to model solar resources for various energy applications such as operational forecasting. Due to the complexity of solving the RT equation, the computation under cloudy conditions can be extremely time consuming though many approximations (e.g. two-stream approach and delta-M truncation scheme) have been utilized. Thus, a more efficient RT model is crucial for model developers as a new option for approximating solar radiation at the land surface with minimal loss of accuracy. We have developed a fast all-sky radiation model for solar applications (FARMS) using the simplified clear-sky RT model, REST2, and simulated cloud transmittances and reflectances from the Rapid Radiation Transfer Model (RRTM) with a sixteen-stream Discrete Ordinates Radiative Transfer (DISORT). Simulated lookup tables (LUTs) of cloud transmittances and reflectances were created by varying cloud optical thicknesses, cloud particle sizes, and solar zenith angles. Equations with optimized parameters were fitted to the cloud transmittances and reflectances to develop the model. Using this model the all-sky solar irradiance at the land surface can be computed rapidly by combining REST2 with the cloud transmittances and reflectances. This new RT model is more than 1000 times faster than those currently utilized in solar resource assessment and forecasting since it does not explicitly solve the RT equation for each individual cloud condition. Our results indicate the accuracy of the fast radiative transfer model is comparable to or better than two-stream approximation in term of computing cloud transmittance and solar radiation.

Xie, Yu↗
DOE OSTI2024

Development of a scintillator based fast-ion loss detector for the Wendelstein 7-X stellarator

A new scintillator based fast-ion loss detector (FILD) system has been designed for the Wendelstein 7-X (W7-X) stellarator. The mechanical design of the system is presented here along with engineering analyses of the system. This includes an assessment of the structural loads which also considers electromagnetic forces calculated for possible disruption scenarios as well as a mode frequency analysis of the system. Furthermore, an analysis of the thermal characteristics of the actively cooled probe head under prescribed steady state and transient heat loads is presented. Finally, the optical relay system is described and its properties used to forward model synthetic camera signals using the FILDSIM code and based on theoretical fast-ion losses incident on the probe head calculated using the ASCOT5 code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Fast-Charging Aging Considerations: Incorporation and Alignment of Cell Design and Material Degradation Pathways

Fast charging of batteries for electric vehicles is seen as one of the most direct ways to enhance adoption. Currently, fast charging is limited by increased cell aging, which is primarily driven by Li plating and degradation of cathode materials. Here, using combined sets of experimental and computational analysis and a suite of different charge protocols, we begin to examine the interplay between failure mode, cell designs, and ultimately aging mechanisms. Slight variation in cell design and the subsequent impacts that charge protocols have on aging can create distinct cell-to-cell variation. As little as 2% difference in porosity change at the cell negative electrode during cycling due to early Li metal plating has been found to alter the aging pathway and either accelerate or inhibit the loss due to Li plating.

25 ENERGY STORAGE↗
DOE OSTI2024

Progress in Fast Modular Reactor Conceptual Design

The Fast Modular Reactor (FMR) is a 100-MW(thermal) gas-cooled fast reactor being developed by General Atomics Electromagnetic System with the goal of developing a FMR for flexible and dispatchable power to the U.S. electricity market in the mid-2030s. The conceptual design aims to develop and verify simplified design features. These include an inert helium gas coolant, pellet-loaded fuel rods, installations with air cooling as ultimate heat sink, and small and passive heat removal systems. The goal is to ensure the development of a safe, maintainable, cost-effective, and distributed nuclear energy-generating station. The baseline technologies selected to achieve this goal are a helium coolant that is an inert gas with no chemical reaction with structural components, not activated, single phase, enabling high-temperature operation and a high thermal efficiency Brayton cycle; conventional uranium dioxide (UO 2 ) fuel, which is the most widely used and well-known fuel material, capable of high burnup (100 MWd/kg) and a long fuel life; and silicon carbide composite (SiGA®) cladding and internal structures that are chemically inert in the helium environment, exceptionally radiation tolerant, and being derisked by accident tolerant fuel technology development. Further, the reactor was specifically designed with passive safety features, including high-temperature in-core materials and a reactor vessel cooling system consisting of cooling panels of naturally circulating water. The passive safety of the core was confirmed for the depressurized loss-of–forced cooling accident, which showed the peak cladding temperature at ~1600°C during the transient, which is below the current design limit of 1800°C. The conceptual design of the FMR has been conducted for the reactor system, vessel system, generator and turbomachine, instrumentation and control, residual heat removal system, plant service system, and containment, as well as pre-application licensing documents.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2026

Technoeconomic Design Optimization for Fast Reactors. Part II: Impact of Technoeconomic Constraints on Optimal Design

There is a current drive toward optimizing reactors, particularly small/micro reactors to minimize cost and maximize performance. Previous work has investigated the development of technoeconomic workflows for the design optimization of pool-type fast reactors that aim to deploy into district energy grids. Initial scoping studies verified that the workflow was capable of capturing design trends throughout a variety of design configurations and problem formulations while remaining sufficiently flexible. In this paper, this methodology is applied to understand how cost functions and technoeconomic constraints can drive optimal reactor design. Specifically, the UPu10Zr-fueled fast reactor model from Part I is adapted to include changes in the fissile content limits, control rod worth limits, control rod drive cost, and assumed fuel form. In the case of constraint relaxation at fixed power (fissile content and control rod worth limits), cost sensitivities of 5% to 10% were uncovered. Multi-objective optimization at varying reactor power levels with individualized control rod drives for each assembly (as opposed to one operational and one safety drive) increased cost by $\$10$ to $\$25$ million and substantially altered the optimal core geometry, favoring geometries with substantially fewer control rod placements relative to baseline optimization. Finally, a multi-objective optimization was performed at varying power levels with the fuel form overhauled to metallic, high-assay low-enriched uranium–based U10Zr with more refined fuel cost models. In the case of uranium fueling, the costs increased by at least $50 million relative to the baseline case. Furthermore, economic fuel zoning and lower reactivity swing cores were recovered. Each case serves to demonstrate the value of applying technoeconomic workflows to initial reactor design scoping studies to better understand the trade-off for a proposed concept between different design options.

Argonne Reactor Computation (ARC) codes↗
DOE OSTI2021

An 802pW 93% Peak Efficiency Buck Converter with 5.5×10 6 Dynamic Range Featuring Fast DVFS and Asynchronous Load-Transient Control

Here this paper presents a buck converter with sub-nW quiescent power, high efficiency, and a wide dynamic range for ultra-low-power (ULP) IoT SoCs. To optimize the SoC power consumption, the buck converter supports fast dynamic voltage and frequency scaling (DVFS) and enables fast load-transient response (FLTR) through asynchronous control. In addition, the buck converter is fully self-contained with all features integrated on chip including a proposed adaptive deadtime controller. Fabricated in 65nm CMOS, measurement results show the buck converter has an 802pW quiescent power at 1.5V input voltage and a 93% peak efficiency. The measured dynamic range is from 0.5nW to 2.75mW, which is over 6 orders of magnitude. The measured voltage droop is 54mV for a 45nA-to-1mA load current step thanks to the asynchronous load-transient detector. The buck converter achieves the highest efficiency and widest dynamic range among all the state-of-the-art sub-nW switching voltage regulators, which makes it well suited for power management in ULP SoCs.

42 ENGINEERING↗
DOE OSTI2021

Ex Situ Catalytic Fast Pyrolysis of Lignocellulosic Biomass to Hydrocarbon Fuels: 2020 State of Technology

Biomass catalytic fast pyrolysis (CFP) research was funded by the Bioenergy Technologies Office (BETO) of the U.S. Department of Energy (DOE) to enable technical breakthroughs to help reduce the cost of conversion of biomass to liquid hydrocarbon fuels. The key goals were to achieve a mature plant modeled Minimum Fuel Selling Price of $3/GGE, with greater than 60% greenhouse gas (GHG) reduction over petroleum derived gasoline by 2022. Experimental results at NREL and PNNL, along with lifecycle analysis by ANL show that we achieved these goals based on performance at the bench scale. A Pt/TiO2 catalyst was used in a fixed bed reactor for upgrading pyrolysis vapors from an upstream fast pyrolysis reactor (ex-situ configuration) to produce CFP oil with 16.5% oxygen content. Subsequent co-hydrotreating of 10 vol% of CFP oil with 90 vol% straight run diesel (SRD) at the bench scale yielded greater than 95% carbon efficiency for the CFP oil portion of the feed. Light oxygenated coproducts were recovered from the off gases from the CFP process via adsorption and subsequent desorption. Aspen Plus modeling of purification of the desorbed stream using the UNIFAC property method showed that acetone and methyl-ethyl-ketone can be purified to chemicals grade and sold as coproducts to benefit the economics and reduce GHG emissions attributed to the fuel product. Some of the key risks and uncertainties associated with this process, and potential future work are mentioned in this report.

09 BIOMASS FUELS↗
DOE OSTI2022

Ultra-fast non-equilibrium synthesis of cathode materials for Li-ion batteries

Synthesis of cathode materials plays an important role in determining the production efficiency, cost and performance of lithium-ion batteries. However, the conventional synthesis methods always experience a slow heating rate and involve a complicated multi-step reaction process and sluggish reaction dynamics, leading to high energy and long time consuming. Herein, we report a high-temperature shock (HTS) strategy for the ultra-fast synthesis of cathode materials in seconds. The HTS process experiences an ultra-high heating rate, leading to a non-equilibrium reaction and fast reaction kinetics and avoiding high energy and long time consuming. Mainstream cathode materials (such as LiMn 2 O 4 , LiCoO 2 , LiFePO 4 , and Li-rich layered oxide/NiO heterostructured material) are successfully synthesized with pure phases, oxygen vacancies, ultra-small particle sizes and good electrochemical performance. In conclusion, the HTS process not only provides an efficient synthesis approach for cathode materials but also can be extended beyond lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Novel Fast Cure Silicone Inks for Single-Step, Support-Free 3D Printing of Tall, Overhanging, and High Aspect Ratio Structures

Silicone elastomers have a broad variety of applications, such as soft robotics, biomedical devices, and structural metamaterials. The extrusion-based method known as direct ink write (DIW) has enabled the production of additively manufactured silicone structures. However, this method is limited to manufacturing mostly planar or pseudo-3D structures. Due to the low self-supporting capabilities of extruded strands for traditional silicone-based “inks,” obtaining tall or overhanging structures, or structures comprised by thin walls is not feasible. Here, in this study, a novel Fast Cure silicone-based ink is demonstrated that enables manufacturing of complex 3D structures. The Fast Cure ink is a two-part mixture and silicone structures are produced by inline mixing and coextrusion of a part containing a catalyst (part A) and a part containing a crosslinker (part B). By the virtue of crosslinking, the extruded strands rapidly rigidize, increasing their self-supportive capacity. Hence, structures can be obtained with superior shape retention and previously unobtainable parts are realized that are tall, with aspect ratios higher than 3, and have overhanging features, achieving inclination angles smaller than 35° with respect to the printing plane. These minimal sag parts are achieved without requiring extra curing or mechanisms, support structures, or suspension baths.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Enabling 4C Fast Charging of Lithium–Ion Batteries by Coating Graphite with a Solid–State Electrolyte

Enabling fast-charging (≥4C) of lithium-ion batteries is an important challenge to accelerate the adoption of electric vehicles. However, the desire to maximize energy density has driven the use of increasingly thick electrodes, which hinders rate capability. Herein, atomic layer deposition is used to coat a single-ion conducting solid electrolyte (Li 3 BO 3 -Li 2 CO 3 ) onto postcalendered graphite electrodes, forming an artificial solid-electrolyte interphase (SEI). When compared to uncoated control electrodes, the solid electrolyte coating: 1) eliminates natural SEI formation during preconditioning; 2) decreases interphase impedance by >75% compared to the natural SEI; and 3) extends cycle life under 4C charging conditions, enabling retention of 80% capacity after 500 cycles (compared to 12 cycles in the uncoated control) in pouch cells with >3 mAh cm –2 loading. Furthermore, this work demonstrates that 4C charging without Li plating can be achieved through purely interfacial modification without sacrificing energy density and sheds new light on the role of the SEI in Li plating and fast-charge performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Insight into the Fast-Rechargeability of a Novel Mo 1.5 W 1.5 Nb 14 O 44 Anode Material for High-Performance Lithium-Ion Batteries

Wadsley–Roth phased niobates are promising anode materials for lithium-ion batteries, while their inherently low electrical conductivity still limits their rate-capability. Herein, a novel doped Mo 1.5 W 1.5 Nb 14 O 44 (MWNO) material is facilely prepared via an ionothermal-synthesis-assisted doping strategy. The detailed crystal structure of MWNO is characterized by neutron powder diffraction and aberration corrected scanning transmission electron microscope, unveiling the full occupation of Mo 6+ -dopant at the t1 tetrahedral site. In half-cells, MWNO exhibits enhanced fast-rechargeability. In this work, the origin of the improved performance is investigated by ultraviolet–visible diffuse reflectance spectroscopy, density functional theory (DFT) computation, and electrochemical impedance spectroscopy, revealing that bandgap narrowing improves the electrical conductivity of MWNO. Furthermore, operando X-ray diffraction elucidates that MWNO exhibits a typical solid-solution phase conversion-based lithium-ion insertion/extraction mechanism with reversible structural evolution during the electrochemical reaction. The boosted lithium-ion diffusivity of MWNO, due to the Mo 6+ /W 6+ doping effect, is confirmed by a galvanostatic intermittent titration technique and DFT. With the simultaneously enhanced electrical conductivity and lithium-ion diffusivity, MWNO successfully demonstrates its fast-rechargeability and practicality in the LiNi 0.5 Mn 1.5 O 4 -coupled full-cells. Therefore, this work illustrates the potential of ionothermal synthesis in energy storage materials and provides a mechanistic understanding of the doping effect on improving material's electrochemical performance.

25 ENERGY STORAGE↗
DOE OSTI2021

A simplified integrated framework for predicting the economic impacts of feedstock variations in a catalytic fast pyrolysis conversion process

Feedstock attributes of lignocellulosic biomass, such as particle size, compositional makeup, and moisture content, can vary substantially even within pre-processed materials and have a significant effect on conversion in fast pyrolysis-based processes. However, the economic impacts of these attributes are not well understood. To address this, biomass deconstruction phenomena captured with a versatile particle-scale simulation were linked to techno-economic impacts via reduced-order models. Parametric analysis of the particle-scale model, which was validated using literature data, was used in combination with multiple linear regression models to develop correlations between feedstock attributes and yields of pyrolysis oil, gas, and char. Yields were then correlated with the minimum fuel selling price (MFSP) using a techno-economic model, bridging the gap between physics-based biomass conversion simulations and predictions of MFSP for a catalytic fast-pyrolysis process. Empirical correlations derived from the literature regarding the impact of mineral matter (ash) on oil yield were also considered. The model correlations deployed in the integrated framework capture the impacts of variation in feedstock attributes on the MFSP. Variations in ash were shown to have the biggest impact, varying MFSP by -13%/+22% due to catalytic effects and lower relative amounts of convertible lignocellulosic material. It was also found that, if ash can be controlled to low levels, the increased extractives in forest residues can help compensate for some yield losses associated with increased ash. As a result, other inputs considered (particle size, moisture content, and reactor temperature) had relatively negligible effects on process economics within the ranges analyzed considering particle-scale effects alone.

BIOMASS FUELS↗
DOE OSTI2023

Manufacturing Water‐Based Low‐Tortuosity Electrodes for Fast‐Charge through Pattern Integrated Stamping

Achieving high energy density and fast charging of lithium‐ion batteries can accelerate the promotion of electric vehicles. However, the increased mass loading causes poor charge transfer, impedes the electrochemical reaction kinetics, and limits the battery charging rate. Herein, this work demonstrated a novel pattern integrated stamping process for creating channels in the electrode, which benefits ion transport and increases the rate performance of the electrode. Meanwhile, the pressure applied during the stamping process improved the contact between electrode and current collector and also enhanced the mechanical stability of the electrode. Compared to the conventional bar‐coated electrode with the same thickness of 155 μm (delivered a discharge capacity of 16 mAh g −1 at the rate of 3 C), the stamped low‐tortuosity LiFePO 4 electrode delivered 101 mAh g −1 capacity. Additionally, water was employed as a solvent in this study. Owing to its eco‐friendliness, high scalability, and minimal waste generation, this novel stamping technique inspire a new method for the industrial‐level efficient roll to roll fabrication of fast‐charge electrodes.

25 ENERGY STORAGE↗