SEARCH · Engineering Papers
Results for “difficult”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Correlating Catalyst Design and Discharged Product to Reduce Overpotential in Li-CO 2 Batteries
Li-CO 2 batteries with dual efficacy for greenhouse gas CO 2 sequestration and high energy output have been regarded as a promising electrochemical energy storage technology. However, battery feasibility has been hampered by inferior electrochemical performance due to large overpotentials and low cyclability primarily caused by the difficult decomposition of ultra-stable Li 2 CO 3 during charge. The use of cathode catalysts has been highlighted as a promising solution and catalyst properties, as well as the nature of discharge products, are closely correlated with electrochemical performance. Here, the catalyst design strategies that include active site enrichment, electrical transport enhancement, and mass transfer improvement are summarized. Catalyst effects on product decomposition are then subsequently introduced, while product geometry and chemical composition will be explored, with an emphasis on the formation/decomposition of Li 2 C 2 O 4 instead of Li 2 CO 3 . Building on previous research, future directions that facilitate improvements in catalyst design are put forward to reinforce the fundamental development of Li-CO 2 batteries.
Monolayer Plasmonic Nanoframes as Large‐Area, Broadband Metasurface Absorbers
Abstract Broadband absorbers are useful ultraviolet protection, energy harvesting, sensing, and thermal imaging. The thinner these structures are, the more device‐relevant they become. However, it is difficult to synthesize ultrathin absorbers in a scalable and straightforward manner. A general and straightforward synthetic strategy for preparing ultrathin, broadband metasurface absorbers that do not rely on cumbersome lithographic steps is reported. These materials are prepared through the surface‐assembly of plasmonic octahedral nanoframes (NFs) into large‐area ordered monolayers via drop‐casting with subsequent air‐drying at room temperature. This strategy is used to produce three types of ultrathin broadband absorbers with thicknesses of ≈200 nm and different lattice symmetries (loose hexagonal, twisted hexagonal, dense hexagonal), all of which exhibit efficient light absorption (≈90%) across wavelengths ranging from 400–800 nm. Their broadband absorption is attributed to the hollow morphologies of the NFs, the incorporation of a high‐loss material (i.e., Pt), and the strong field enhancement resulting from surface assembly. The broadband absorption is found to be polarization‐independent and maintained for a wide range of incidence angles (±45°). The ability to design and fabricate broadband metasurface absorbers using this high‐throughput surface‐based assembly strategy is a significant step toward the large‐scale, rapid manufacturing of nanophotonic structures and devices.
High Sensitivity of Non–Fullerene Organic Solar Cells Morphology and Performance to a Processing Additive
Although solvent additives are used to optimize device performance in many novel non-fullerene acceptor (NFA) organic solar cells (OSCs), the effect of processing additives on OSC structures and functionalities can be difficult to predict. Here, two polymer-NFA OSCs with highly sensitive device performance and morphology to the most prevalent solvent additive chloronaphthalene (CN) are presented. Devices with 1% CN additive are found to nearly double device efficiencies to 10%. However, additive concentrations even slightly above optimum significantly hinder device performance due to formation of undesirable morphologies. A comprehensive analysis of device nanostructure shows that CN is critical to increasing crystallinity and optimizing phase separation up to the optimal concentration for suppressing charge recombination and maximizing performance. Here, domain purity and crystallinity are highly correlated with photocurrent and fill factors. However, this effect is in competition with uncontrolled crystallization of NFAs that occur at CN concentrations slightly above optimal. This study highlights how slight variations of solvent additives can impart detrimental effects to morphology and device performance of NFA OSCs. Furthermore, successful scale-up processing of NFA-based OSCs will require extreme formulation control, a tuned NFA structure that resists runaway crystallization, or alternative methods such as additive-free fabrication.
Hydrogen Storage in Partially Exfoliated Magnesium Diboride Multilayers
Metal boride nanostructures have shown significant promise for hydrogen storage applications. However, the synthesis of nanoscale metal boride particles is challenging because of their high surface energy, strong inter- and intraplanar bonding, and difficult-to-control surface termination. Here, it is demonstrated that mechanochemical exfoliation of magnesium diboride in zirconia produces 3-4 nm ultrathin MgB 2 nanosheets (multilayers) in high yield. High-pressure hydrogenation of these multilayers at 70 MPa and 330 °C followed by dehydrogenation at 390 °C reveals a hydrogen capacity of 5.1 wt%, which is ≈50 times larger than the capacity of bulk MgB 2 under the same conditions. This enhancement is attributed to the creation of defective sites by ball-milling and incomplete Mg surface coverage in MgB 2 multilayers, which disrupts the stable boron-boron ring structure. The density functional theory calculations indicate that the balance of Mg on the MgB 2 nanosheet surface changes as the material hydrogenates, as it is energetically favorable to trade a small number of Mg vacancies in Mg(BH 4 ) 2 for greater Mg coverage on the MgB 2 surface. To conclude, the exfoliation and creation of ultrathin layers is a promising new direction for 2D metal boride/borohydride research with the potential to achieve high-capacity reversible hydrogen storage at more moderate pressures and temperatures.
Tailoring a 3D Covalent Organic Framework Toward Facile Functionalization
Three-dimensional covalent organic frameworks (3D COFs) are notably crystalline and stable, but their architectures and monomer structures make them difficult to functionalize. Here, a new strategy is presented to render COF-300 and other imine-linked frameworks amenable to facile functionalization in the last step of synthesis. By reducing the imine linkages to secondary amines and appending them with acetyl halide groups, the linkages are converted to electrophiles that can be readily reacted with nucleophilic guests. This route yields eight new COF-300 derivatives, bearing chloroacetyl, bromoacetyl, azide, cyano, amino, hydroxyl, methoxy, or thiomethyl groups appended to the inter-monomer linkages. The new materials are characterized through solid-state NMR, infrared spectroscopy, and powder X-ray diffraction, among other techniques, finding that the reported linkage transformations proceed to complete conversion while retaining the crystallinity of the materials. Microcrystal electron diffraction (microED) data are used to solve the evacuated structure of the amine-linked framework COF-300-AR for the first time, providing conclusive evidence of this framework's guest-induced phase change, along with the structure of the new framework COF-300-NH 2 . Finally, COF-300-NH 2 is shown to have significantly improved adsorption capacity for CO 2 and perfluoroalkyl substances (PFAS), highlighting the benefits of this synthetic strategy for the generation of customized adsorbents.
HRTEM Imaging and Mechanistic Insights Into Carbon Nanotube Nucleation and Growth on Fe Nanocatalysts in a Thermal Plasma
Thermal plasma decomposition of natural gas is a scalable pathway for the production of hydrogen alongside high-value carbon nanotubes (CNTs). Metals evaporate from an electrode and condense to form seed nanoparticles that nucleate and grow CNTs. However, the lack of mechanistic understanding of the CNT nucleation and growth processes in thermal plasma makes control over CNT diameter, chirality, length, and yield difficult. We debundled and separated CNTs from soots produced using iron (Fe) nanocatalysts, and distributed them on monolayer graphene for high-resolution transmission electron microscopy (HRTEM) imaging to gain mechanistic insights. Full graphene encapsulation was found for relatively small Fe nanoparticles that were molten at high temperatures. Zigzag single-wall or double-wall CNTs (SWCNTs or DWCNTs) appeared to have grown out directly from the graphene covering on the conical or cylindrical bodies of small molten Fe nanodroplets with high curvature. Also, SWCNTs likely grew out from H- or O-atom etched single-wall carbon nanocones observed on conical Fe nanoparticles. A SWCNT/DWCNT could also be generated from the cracked opening of the graphene covering on a face-centered cubic (FCC) Fe nanoparticle. A simple, plausible pathway is proposed for the growth of an open, H-passivated, zigzag SWCNT involving reaction of CH 2 and CH radicals at high temperatures.
Codesigning Alloy Compositions of CdSe y Te 1− y Absorbers and Mg x Zn 1− x O Contacts to Increase Solar Cell Efficiency
Thin‐film solar cells such as CdTe are a major commercial photovoltaic technology, with more than 25 GW installed worldwide and levelized costs of electricity competitive with fossil fuels. Further progress may result from integrating CdSe y Te 1− y absorbers with Mg x Zn 1− x O contacts, but the device efficiency is difficult to maximize due to coupled dependence on chemical composition of both alloys. Herein, a high‐throughput approach is demonstrated to codesign chemical compositions in alloyed Mg x Zn 1− x O/CdSe y Te 1− y thin‐film solar cells, using combinatorial libraries of PV devices with orthogonal composition gradients in CdSe y Te 1− y absorbers and Mg x Zn 1− x O contacts. It is found that the solar cell performance is a strong and coupled function of both elemental compositions, with efficiency up to 17.7% ( V OC = 836 mV, fill factor = 69%, J SC = 30.6 mA cm −2 ) at atomic compositions of Mg/(Mg + Zn) ≈18% and average Se/(Se + Te) ≈4%. These performance trends among >100 devices are explained by >100 ns lifetime of photoexcited charge carriers at the Mg x Zn 1− x O/CdSe y Te 1− y interface where strong Se accumulation is also observed. This study reports the optimal compositions of the commercially relevant Mg x Zn 1− x O/CdSe y Te 1− y solar cells and demonstrates a general approach to codesigning performance of alloyed thin‐film solar cells and other optoelectronic devices.
Blade Coating Inverted Perovskite Solar Cells with Vacuum-Assisted Nucleation Based on Bottom Quasi-2D Passivation
Metal halide perovskite solar cells (PSCs) attract an enormous attention because of their high power conversion efficiency (PCE) and low fabrication cost. However, their commercialization is limited by fabricating highly efficient large-area solar cells. Controlling the morphology and crystallization of perovskite for large-area fabrication is difficult but important. Here, in this work, a vacuum-assisted approach is developed to obtain mirror-like, pinhole-free, highly crystalline, and uniform blade-coated perovskite films, without the use of antisolvent and air knife. This method can be a universal approach for various perovskite compositions. Meanwhile, the phenethylammonium iodide passivation effect at the top and bottom interfaces of perovskite layer based on FTO/NiO x /perovskite/C 60 /BCP/Cu inverted p-i-n structure is systematically investigated. The optimized device fabricated by blade coating under an ambient environment exhibits the champion PCE of 20.7% and is among the top few records of blade coating inverted structure based on NiOx hole transport layer. The encapsulated device retains 97% of its maximum efficiency under open-circuit condition after 1000 h of photostability test in an ambient environment at room temperature with a relative humidity of 40–60%. Herein, low-cost, easy, and reproducible strategies to fabricate efficient and stable blade-coated PSCs are demonstrated.
Charge Carrier Lifetime Determination in Graded Absorber Solar Cells Using Time‐Resolved Photoluminescence Simulations and Measurements
Thin‐film photovoltaic device efficiencies are limited by carrier recombination, thus understanding recombination mechanisms is critical for performance improvements. Bulk minority carrier lifetime ( τ bulk ) is a critical parameter for solar cells but is difficult to determine in P–N junction devices, especially for high doping. As doping ≥10 16 cm −3 is required for efficient drift‐charge‐carrier‐collection devices, a method for τ bulk determination in doped P–N junction devices is necessary. This work utilizes time‐resolved photoluminescence (TRPL) simulations to quantify bulk and interface recombination properties in highly doped, graded absorber CdSeTe structures. The two methods developed here for τ bulk determination include utilization of an instantaneous lifetime representation to guide TRPL fitting and direct comparison between measured and simulated decays. Simulations verified that both methods are valid for state‐of‐the‐art device architectures which include graded bandgap absorbers, graded doping, and graded lifetimes. Shifts in the dominant recombination mechanism are identified for sufficiently long τ bulk , where front and back interface quality plays a more prominent role. Evaluation of surface recombination velocities and conduction band offset illustrate electro‐optical advantages of a positive conduction band offset and highlight the necessity of improved interfaces as bulk quality in photovoltaic devices improves.
Improving Stability of Triple-Cation Perovskite Solar Cells under High-Temperature Operation
Metal halide perovskite photovoltaic performance required for commercial technology encompasses both efficiency and stability. Advances in both these parameters have recently been reported; however, these strategies are often difficult to directly compare due to differences in perovskite composition, device architecture, fabrication methods, and accelerated stressors applied in stability tests. In particular, it is found that there is a distinct lack of elevated temperature, operational (light and bias) stability data. Furthermore, significant testing is required to understand the interactions when combinations are used (e.g., additives used with posttreatments). Herein, individual and combined additive, posttreatment, and contact layer strategies from recent literature reports under standardized operational stability tests of p-i-n CsMAFA perovskites at 70 degrees C are evaluated. Through analysis of over 1000 devices, it is concluded that the hole-transport layer (HTL) is the most significant component impacting elevated temperature operational stability. This analysis motivates future development of high-performance HTLs.
Understanding and Advancing Bifacial Thin Film Solar Cells under Dual Illumination
There is a great deal of interest in increasing the energy yield from thin film solar cells by implementing bifacial operation. However, deleterious band bending and high interface recombination at the back transparent electrode can cause problems. Herein, it is investigated how bifacial thin film devices perform when illuminated through the front, back, and simultaneously through both interfaces using numerical modeling. It is shown that the downward band bending near the back interface is reduced during illumination when the carrier concentration is low. This effect is not found when the doping is relatively high, but the minority carrier distribution is still modified. Under either condition, the power generated under bifacial illumination exceeds the sum of the power generated when the illumination is solely from the back or the front. It is also shown that the back-illuminated device performance is independent of the angle at which the light enters the back of the device, which provides accommodation for scattered light. Finally, the power enhancement is calculated for bifacial devices relative to front-illuminated devices, and is shown that any significant loss in frontside power generation is difficult to overcome with back illumination under real-world albedo conditions.
Holistic Microstructure Control Strategies in Photopolymerization‐Induced Phase Separation of Acrylate Systems
Open porous materials, known for their large surface area and interconnected structures, are essential in various applications, including batteries, ion exchange, catalysis, filtration, and electronic waste recycling. A critical aspect of the functionality of porous membranes is the precise control of pore size and morphology. Photopolymerization-induced phase separation (photo-PIPS) offers a convenient and versatile methods for creating porous structures. However, controlling the porous morphology remains challenging due to the complex interplay between thermodynamics, polymerization kinetics, and monomer structures, which makes it difficult to establish the relationship between processing conditions and resulting morphology in photo-PIPS. Herein, a physics-based phase-field model capable of generating and characterizing the microstructures of porous materials based on both average and localized features is developed. Using the phase-field simulations as test bed, the effects of polarity, light intensity, and curing temperature, as well as the previously unexplored roles of chain transfer agents and substrates, on the morphology of the resulting porous microstructure are investigated. Experiments are performed to verify the results predicted by the simulations. This work lays out a comprehensive guide for designing PIPS-derived porous microstructures and offers practical engineering strategies for tailoring microstructure-level topology and size of pores for application-specific needs.
Visualisation and outlier detection for probability density function ensembles
Abstract Exploratory data analysis (EDA) for functional data—data objects where observations are entire functions—is a difficult problem that has seen significant attention in recent literature. This surge in interest is motivated by the ubiquitous nature of functional data, which are prevalent in applications across fields such as meteorology, biology, medicine and engineering. Empirical probability density functions (PDFs) can be viewed as constrained functional data objects that must integrate to one and be nonnegative. They show up in contexts such as yearly income distributions, zooplankton size structure in oceanography and in connectivity patterns in the brain, among others. While PDF data are certainly common in modern research, little attention has been given to EDA specifically for PDFs. In this paper, we extend several methods for EDA on functional data for PDFs and compare them on simulated data that exhibit different types of variation, designed to mimic that seen in real‐world applications. We then use our new methods to perform EDA on the breakthrough curves observed in gas transport simulations for underground fracture networks.
Calibration, measurement, and characterization of soil moisture dynamics in a central Amazonian tropical forest
Soil moisture plays a key role in hydrological, biogeochemical, and energy budgets of terrestrial ecosystems. Accurate soil moisture measurements in remote ecosystems such as the Amazon are difficult and limited because of logistical constraints. Time domain reflectometry (TDR) sensors are widely used to monitor soil moisture and require calibration to convert the TDR's dielectric permittivity measurement (K a ) to volumetric water content (θ v ). In this study, our objectives were to develop a field-based calibration of TDR sensors in an old-growth upland forest in the central Amazon, to evaluate the performance of the calibration, and then to apply the calibration to determine the dynamics of soil moisture content within a 14.2 -m-deep vertical soil profile. Depth-specific TDR calibration using local soils in a controlled laboratory setting yielded a novel K a –θ v third-degree polynomial calibration. The sensors were later installed to their specific calibration depth in a 14.2-m pit. The widely used K a –θ v relationship (Topp model) underestimated the site-specific θ v by 22–42%, indicating significant error in the model when applied to these well-structured, clay-rich tropical forest soils. The calibrated wet- and dry-season θ v data showed a variety of depth and temporal variations highlighting the importance of soil textural differentiation, root uptake depths, as well as event to seasonal precipitation effects. Data such as these are greatly needed for improving our understanding of ecohydrological processes within tropical forests and for improving models of these systems in the face of changing environmental conditions.
Microbial O 2 consumption as a function of pore structure in soils of sorghum, switchgrass, and prairie vegetation systems
Abstract Microscale O 2 availability in soil, a main factor influencing microbial processing of soil carbon and nitrogen, is a function of O 2 diffusion and microbial O 2 consumption. While O 2 diffusivity is widely studied, it is difficult to quantify the rate of microbial O 2 consumption ( MO ). In this study, we quantified the MO using O 2 microsensor profiling to compare MO in different soils and vegetation systems while manipulating the soil pore structure. Soil samples were collected from three bioenergy vegetation systems, sorghum ( Sorghum bicolor L. Moench), switchgrass ( Panicum virgatum L.), and prairie, at an experimental site in Southeast Michigan, and from switchgrass and prairie systems at two sites in South and North Wisconsin. We prepared soil cores with two contrasting pore structures, that is, large (>30 µm Ø) pore‐dominated soil (LP) and small (<10 µm Ø) pore‐dominated soil (SP), from the same 1‐ to 2‐mm soil size fraction. We quantified MO (nmol O 2 cm −3 s −1 ) using a microprofiler with an oxygen (OX‐100 µm) microsensor (Unisense) pre‐ and post‐38‐day incubation. Across all studied systems, there was a trend for a decrease in SP MO post‐incubation, suggesting a change in microbial metabolism to lower O 2 utilization. However, sizeable microbial O 2 consumption continued in the LP soils, further corroborated by a positive correlation between the C‐CO 2 emission rate and the post‐incubation MO , highlighting that LP provided a better physical microenvironment for the soil microbes.
Investigations of water/oxide interfaces by molecular dynamics simulations
Water/oxide interfaces are ubiquitous on earth and show significant influence on many chemical processes. For example, understanding water and solute adsorption as well as catalytic water splitting can help build better fuel cells and solar cells to overcome our looming energy crisis; the interaction between biomolecules and water/oxide interfaces is one hypothesis to explain the origin of life. However, knowledge in this area is still limited due to the difficulty of studying water/solid interfaces. As a result, research using increasingly sophisticated experimental techniques and computational simulations has been carried out in recent years. Although it is difficult for experimental techniques to provide detailed microscopic structural information, molecular dynamics (MD) simulations have satisfactory performance. In this report, we discuss classical and ab initio MD simulations of water/oxide interfaces. Generally, we are interested in the following questions: How do solid surfaces perturb interfacial water structure? How do interfacial water molecules and adsorbed solutes affect solid surfaces and how do interfacial environments affect solvent and solute behavior? Finally, we discuss progress in the application of neural network potential based MD simulations, which offer a promising future because this approach has already enabled ab initio level accuracy for very large systems and long trajectories.
New insights on wind turbine wakes from large‐eddy simulation: Wake contraction, dual nature, and temperature effects
Abstract Large‐eddy simulation (LES) has been adopted to study wind turbine wakes because it can capture fine‐scale details of turbulent wind flows and interactions with wind turbines. Here, we use the LES version of the Weather Research and Forecasting (WRF) model with an actuator disk model to gain insights on several wake effects that have been traditionally difficult to measure. The first finding is that the wake has a “dual nature,” meaning that the wind speed deficit behaves differently from the added turbulent kinetic energy (TKE) and the two are not co‐located in space. For example, the wind speed deficit peaks at hub height and reaches the ground within 8D (D is the rotor diameter), but added TKE peaks near the rotor tip and generally remains aloft. Second, temperature changes near the ground are driven by the added TKE in the rotor area and by atmospheric stability. The combination of these two factors determines the sign and intensity of the vertical heat flux divergence below the rotor, with convergence and warming associated with stable conditions and weak divergence and modest cooling with unstable conditions. Third, wakes do not expand indefinitely, as suggested by similarity theory applied to the wind speed deficit, but eventually stop expanding and actually contract, at different rates depending on atmospheric stability. The implication of these findings is that, in order to study wakes, it is not sufficient to focus on wind speed deficit alone, because TKE is also important and yet behaves differently from the wind speed deficit.