Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dielectric materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Microwave dielectric properties of plant materials

Three waveguide transmission systems covering the 1-2, 3.5-6.5, and 7.5-8.5 GHZ bands were used to measure the dielectric properties of vegetation material as a function of moisture content and microwave frequency. The materials measured included, primarily, the leaves and stalks of corn and wheat. Dielectric measurements also were made of the liquid included in the vegetation material after it was extracted from the vegetation by mechanical means. The extracted liquids were found to have an equivalent NaCl salinity of about 10 per mil, which can have a significant effect on the dielectric loss at frequencies below 5 GHz. The results of attempts to model the dielectric constant of the vegetatioon-water mixture in terms of the dielectric constants and volume fractions of its constituent parts (i.e., bulk vegetation, air, bound water, and free water) are discussed. Additionally, measurements of the temporal variations in the total attenuation at 10.2 GHz are presented for a corn canopy and a soybean canopy.

Ulaby, F. T.↗
NASA NTRS1992

Dielectric-Particle Injector For Processing Of Materials

Device generates electrically charged particles of solid, or droplets of liquid, fabricated from dielectric material and projects them electrostatically, possibly injecting them into electrostatic-levitation chamber for containerless processing. Dielectric-particle or -droplet injector charges dielectric particles or droplets on zinc plate with photo-electrons generated by ultraviolet illumination, then ejects charged particles or droplets electrostatically from plate.

Leung, Philip L.↗
DOE OSTI2024

High-performance 2D electronic devices enabled by strong and tough two-dimensional polymer with ultra-low dielectric constant

As the feature size of microelectronic circuits is scaling down to nanometer order, the increasing interconnect crosstalk, resistance-capacitance (RC) delay and power consumption can limit the chip performance and reliability. To address these challenges, new low-k dielectric (k < 2) materials need to be developed to replace current silicon dioxide (k = 3.9) or SiCOH, etc. However, existing low-k dielectric materials, such as organosilicate glass or polymeric dielectrics, suffer from poor thermal and mechanical properties. Two-dimensional polymers (2DPs) are considered promising low-k dielectric materials because of their good thermal and mechanical properties, high porosity and designability. Here, we report a chemical-vapor-deposition (CVD) method for growing fluoride rich 2DP-F films on arbitrary substrates. We show that the grown 2DP-F thin films exhibit ultra-low dielectric constant (in plane k = 1.85 and out-of-plane k = 1.82) and remarkable mechanical properties (Young’s modulus > 15 GPa). We also demonstrated the improved performance of monolayer MoS 2 field-effect-transistors when utilizing 2DP-F thin films as dielectric substrates.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Dielectric particle injector for material processing

A device for use as an electrostatic particle or droplet injector is disclosed which is capable of injecting dielectric particles or droplets. The device operates by first charging the dielectric particles or droplets using ultraviolet light induced photoelectrons from a low work function material plate supporting the dielectric particles or droplets, and then ejecting the charged particles or droplets from the plate by utilizing an electrostatic force. The ejected particles or droplets are mostly negatively charged in the preferred embodiment; however, in an alternate embodiment, an ion source is used instead of ultraviolet light to eject positively charged dielectric particles or droplets.

Leung, Philip L.↗
NASA NTRS2006

Polarization Phase-Compensating Coats for Metallic Mirrors

A method of compensating for or minimizing phase differences between orthogonal polarizations of light reflected from metallic mirrors at oblique incidence, as, for example, from weakly curved mirrors, is undergoing development. The method is intended to satisfy a need to maintain precise polarization phase relationships or minimum polarization differences needed for proper operation of telescopes and other scientific instruments that include single or multiple mirrors. The basic idea of the method is to optimally coat mirrors with thin engineered layers of materials that introduce phase differences that, as nearly precisely as possible, are opposite of the undesired phase differences arising in reflection with non-optimum coatings. Depending on the specific optical system, the method could involve any or all of the following elements: a) Optimization of a single coat on all the mirrors in the system. b) Optimization of a unique coat for each mirror such that the polarization phase effects of the coat on one mirror compensate, to an acceptably high degree over an acceptably wide wavelength range, for those of the coat on another mirror. c) Tapering the coat on each mirror. Optimization could involve the choice of a single dielectric coating material and its thickness, or design of a more complex coat consisting of multiple layers of different dielectric materials and possibly some metallic materials. Such designs and coatings are particularly significant and needed for obtaining very high quality of wavefront required in high-contrast imaging instruments such as the NASA Terrestrial Planet Finder Coronagraph.

Balasubramanian, Kunjithapatham↗
NASA NTRS1970

Edge coating of flat wires

An apparatus and technique is described for the coating of the edge surfaces of flat ribbon conductors with an adherent coating of a dielectric insulating material. Means for passing the ribbon conductors between a pair of generally axially aligned rollers is provided. The edge surfaces of the conductor are disposed adjacent to and generally tangentially to the confronting surfaces of the roller so as to form a fillet of dielectric material along the edge surface of the conductor.

Marcell, G. V.↗
NASA NTRS2013

Stress-Dependent Voltage Offsets From Polymer Insulators Used in Rock Mechanics and Material Testing

Dielectric insulators are used in a variety of laboratory settings when performing experiments in rock mechanics, petrology, and electromagnetic studies of rocks in the fields of geophysics,material science, and civil engineering. These components may be used to electrically isolate geological samples from the experimental equipment, to perform a mechanical compliance function between brittle samples and the loading equipment, to match ultrasonic transducers, or perform other functions. In manyexperimental configurations the insulators bear the full brunt of force applied to the sample but do not need to withstand high voltages, therefore the insulators are often thin sheets of mechanically tough polymers. From an instrument perspective, transduction from various types of mechanical perturbation has beenqualitatively compared for a number of polymers [1, 2] and these error sources are readily apparent duringhigh-impedance measurements if not mitigated. However even when following best practices, a force dependent voltage signal still remains and its behavior is explored in this presentation. In this experimenttwo thin sheets (0.25 mm) of high-density polyethylene (HDPE) were set up in a stack, held alternatelybetween three aluminum bars; this stack was placed on the platen of a 60T capacity hydraulic testingmachine. The surface area, A, over which the force is applied to the PE sheets in this sandwich is roughly 40 square cm, each sheet forming a parallel-plate capacitor having roughly 320 pF [3], assuming therelative dielectric permittivity of PE is approximately 2.3. The outer two aluminum bars were connected to the LO input ofthe electrometer and the central aluminum bar was connected to the HI input of a Keithley model 617 electrometer. Once the stack is mechanically well-seated with no air gaps, the voltage offset is observed tobe a linear function of the baseline voltage for a given change in applied force. For a periodically appliedforce of 66.7 kN the voltage offsets were measured as a function of initial voltage, and these data were fitwith a linear function that was constrained to pass through the origin. The best fit solution had a correlation coefficient of R=0.85 and a slope of approximately -0.0228 volts/volt. The voltage offset when normalizedis demonstrated to be constant -2.28% for both positive and negative polarities over nearly 3 orders ofbaseline voltage magnitude. From this, the voltage-force coefficient is derived to be -0.34 ppm/N. Thiscorrelates well to a first-order parallel plate capacitor model that assumes constant area, and smalldeformation such that the polymer may be mechanically modeled by a spring that obeys Hookes law. Thissimple model predicts that the coefficient of proportionality is a function of Youngs modulus E= 0.8 GPaand surface area of the insulator, theoretically -1EA= -0.31 ppm/N. The outcome of this work is animproved insulator made from ultra-high molecular weight (UHMW) polyethylene and other approachestoward the minimization of and compensation for these experimental artifacts.

Electromagnetic Studies of Rocks↗
DOE OSTI2023

Behavior of soda-lime silicate glass under laser-driven shock compression up to 315 GPa

Shock experiments give a unique insight into the behavior of matter subjected to extremely high pressures and temperatures. Understanding the behavior of materials under such extreme conditions is key to modeling material failure and deformation dynamics under impact. While studies on pure silica are extensive, the shock behavior of other commercial silicates that contain additional oxides has not been systematically investigated. To better understand the role of composition in the dynamic behavior of silicates, we performed laser-driven dynamic compression experiments on soda-lime glass (SLG) up to 315 GPa. Using the accurate pulse shaping offered by the long pulse laser system at the Matter in Extreme Conditions end-station at the Linac Coherent Light Source, SLG was shock compressed along the Hugoniot to multiple pressure-temperature points. Velocity Interferometer System for Any Reflector was used to measure the velocity and determine the pressure inside the SLG. The U s –u p relationship obtained agrees well with the previous parallel plate impact studies. Within the error bars, no transformation to the crystalline phase was observed up to 70 GPa, which is in contrast to the behavior of pure silica under shock compression. Our studies show that the glass composition strongly influences the shock compression behavior of the silicate glasses.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Mineral equilibria and the high radar reflectivity of Venus mountaintops

The relationship between altitude and microwave emissivity in 10 highland regions of Venus is investigated on the basis of the Magellan data set. Highlands on Venus are found to display high radar reflectivity. The required change in surface electrical properties occurs abruptly at a 'critical altitude,' whose value varies from one highland area to another. Critical altitudes range from 4.75 km to 2.49 km. Differences in reflectivity are caused by differences in the surface mineral assemblage, which determines the dielectric constant of surface material. The mineral responsible for high radar reflectivity on mountaintops is pyrite, which occurs in weathered mineral assemblages at high altitudes. Conductive pyrite occurs dispersed in insulating materials, forming a loaded dielectric material.

Klose, K. B.↗
NASA NTRS1990

Dielectric properties measurement of substrate and support materials

In this paper a fast and straightforward waveguide measurement technique is described for the determination of the dielectric constant and loss tangent of many commercially available materials. These dielectric materials include Cuflon, Teflon, Arlon's polyimides, Lockheed's ceramic foams, and Rogers Duroid materials. The effective dielectric constant and loss tangent of Hexsel's honeycomb material is also measured by this method and is compared to the predicted data obtained using the volume averaging theory. The accuracy and other features of this measurement technique are also discussed.

Wu, Te-Kao↗
DOE OSTI2020

First-principles predictions of temperature-dependent infrared dielectric function of polar materials by including four-phonon scattering and phonon frequency shift

Recently, first-principles calculations based on density functional theory have been widely used to predict the temperature-dependent infrared spectrum of polar materials, but the calculations are usually limited to the harmonic frequency (0 K) and three-phonon scattering damping for the zone-center infrared-active optical phonon modes, and fail to predict the high-temperature infrared optical properties of materials such as sapphire (α–Al 2 O 3 ), GaAs, TiO 2 , etc., due to the neglect of high-order phonon scattering damping and phonon frequency shift. In this work, we implemented first-principles calculations to predict the temperature-dependent infrared dielectric function of polar materials by including four-phonon scattering and phonon frequency shift. The temperature-dependent phonon damping by including three- and four-phonon scattering as well as the phonon frequency shift by including cubic and quartic anharmonicity and the thermal expansion effect are calculated based on anharmonic lattice dynamics method. The infrared dielectric function of α–Al 2 O 3 is parameterized, and then the temperature-dependent infrared optical reflectance is determined. We find that our predictions agree better with the experimental data than the previous density functional theory-based methods. Lastly, this work will help to effectively predict the thermal radiative properties of polar materials at elevated temperature, which is generally difficult to measure, and will enable predictive design of new materials for radiative applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1991

Effective area of the AXAF X-ray telescope - Dependence upon dielectric constants of coating materials

This study examines the dependence of the effective area of the AXAF X-ray telescope upon the complex dielectric constants of possible mirror coatings, over the energy range 0.1-10 keV. At energies near and above the astrophysically important iron-line complex near 6.7 keV, the effective area is very sensitive to the coating density on the three innermost of the telescope's six mirror pairs. Thus, it is desirable to achieve as high a density as feasible. The telescope's spectral response exhibits sharp features at absorption edges of the coating materials. In view of the exceptional energy resolution of the AXAF spectrometers and uncertainties in reflectivities (especially near absorption edges), the AXAF goal of 1-percent accuracy requires both the precise X-ray calibration of the telescope and improved modeling of the telescope and calibration sources. Presented here in the form of plots, the results are also available (on floppy disks) in tabular form.

Elsner, R. F.↗
NASA NTRS1993

Measurements of the dielectric properties of simulated comet material as part of the KOSI 10 experiment

The dielectric constant epsilon of the snow-mineral used for the comet simulation in the German KOSI 10 experiment was measured in the radio frequency range from 2 to 4 GHz. The traditional microwave bridge method was used, but instead of using a waveguide that contains the sample material small lambda/4 antennas were used as sensors. A change in the dielectric properties indicates a change in density and/or composition, respectively. The method is presented as an analytical tool for measuring such density or composition changes during alteration snow-dust materials. The KOSI (determined from the German: Kometen Simulation) experiments, performed in the Space simulator of the DLR/Institut for Raumsimulation, during the last years revealed many processes that presumably take place on comets. So far, modifications of the internal structure could be identified only during the post-experiment inspection via hardness tests. It was the aim of the KOSI 10 and KOSI 10a experiments to emphasize on a synoptic detection of events like particle emission or crust formation. The composition of the KOSI 10 sample material was an ice-mineral mixture with about 10 percent mineral (olivine) content. An excellent method to investigate the change of the density of the probe material during its exposure to the artificial sun in situ is to do it via the measurement of the dielectric constant. The traditional method to determine epsilon, by using a microwave-bridge to measure the transmission and the reflection factor of the sample material for electromagnetic waves in the radio frequency range, was modified, since the commonly used practice to fill the sample material into a waveguide was not compatible with the need for in situ measurements during the simulation experiment.

Ulamec, S.↗
DOE OSTI2023

Autonomous hydrogel locomotion regulated by light and electric fields

Autonomous robotic functions in materials beyond simple stimulus-response actuation require the development of functional soft matter that can complete well-organized tasks without step-by-step control. We report the design of photo- and electroactivated hydrogels that can capture and deliver cargo, avoid obstacles, and return without external, stepwise control. By incorporating two spiropyran monomers with different chemical substituents in the hydrogel, we created chemically random networks that enabled photoregulated charge reversal and autonomous behaviors under a constant electric field. In addition, using perturbations in the electric field induced by a dielectric inhomogeneity, the hydrogel could be attracted to high dielectric constant materials and autonomously bypasses the low dielectric constant materials under the guidance of the electric field vector. The photo- and electroactive hydrogels investigated here can autonomously perform tasks using constant external stimuli, an encouraging observation for the potential development of molecularly designed intelligent robotic materials.

42 ENGINEERING↗
DOE OSTI2023

Temperature-dependent complex dielectric permittivity: a simple measurement strategy for liquid-phase samples

Abstract Microwaves (MWs) are an emerging technology for intensified and electrified chemical manufacturing. MW heating is intimately linked to a material’s dielectric permittivity. These properties are highly dependent on temperature and pressure, but such datasets are not readily available due to the limited accessibility of the current methodologies to process-oriented laboratories. We introduce a simple, benchtop approach for producing these datasets near the 2.45 GHz industrial, medical, and scientific (ISM) frequency for liquid samples. By building upon a previously-demonstrated bireentrant microwave measurement cavity, we introduce larger pressure- and temperature-capable vials to deduce temperature-dependent permittivity quickly and accurately for vapor pressures up to 7 bar. Our methodology is validated using literature data, demonstrating broad applicability for materials with dielectric constant ε' ranging from 1 to 100. We provide new permittivity data for water, organic solvents, and hydrochloric acid solutions. Finally, we provide simple fits to our data for easy use.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Negative capacitance regime in antiferroelectric PbZrO 3

The potential of antiferroelectrics to exhibit a negative capacitance regime has been largely overlooked as all the attention focused on their polar counterparts, ferroelectrics. We use nonequilibrium first-principles-based molecular dynamics to probe a negative capacitance regime in prototypical antiferroelectric PbZrO 3 . Simulations predict that this antiferroelectric can exhibit a negative capacitance/susceptibility regime in response of polarization to an internal electric field, which is a superposition of applied and residual depolarizing fields. Consequently, the regime emerges when the polarization surface charge in the polar phase of antiferroelectric is not fully screened, as is often the case in thin films and nanostructures. The negative capacitance regime occurs below the Curie temperature and disappears in the paraelectric phase. We find that the time the material spends in the negative capacitance regime is proportional to the time needed to complete antipolar–polar (or its reverse) transition and shortens as the frequency of the applied field increases. Furthermore, a negative susceptibility value exhibits strong dependence on the quality of surface charge screening with the largest in magnitude values occurring in the vicinity of the transition into a negative capacitance regime.

36 MATERIALS SCIENCE↗