Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “designed experiment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Development of an Integrated Nozzle for a Symmetric, RBCC Launch Vehicle Configuration

The development of rocket based combined cycle (RBCC) engines is highly dependent upon integrating several different modes of operation into a single system. One of the key components to develop acceptable performance levels through each mode of operation is the nozzle. It must be highly integrated to serve the expansion processes of both rocket and air-breathing modes without undue weight, drag, or complexity. The NASA GTX configuration requires a fixed geometry, altitude-compensating nozzle configuration. The initial configuration, used mainly to estimate weight and cooling requirements was a 1 So half-angle cone, which cuts a concave surface from a point within the flowpath to the vehicle trailing edge. Results of 3-D CFD calculations on this geometry are presented. To address the critical issues associated with integrated, fixed geometry, multimode nozzle development, the GTX team has initiated a series of tasks to evolve the nozzle design, and validate performance levels. An overview of these tasks is given. The first element is a design activity to develop tools for integration of efficient expansion surfaces With the existing flowpath and vehicle aft-body, and to develop a second-generation nozzle design. A preliminary result using a "streamline-tracing" technique is presented. As the nozzle design evolves, a combination of 3-D CFD analysis and experimental evaluation will be used to validate the design procedure and determine the installed performance for propulsion cycle modeling. The initial experimental effort will consist of cold-flow experiments designed to validate the general trends of the streamline-tracing methodology and anchor the CFD analysis. Experiments will also be conducted to simulate nozzle performance during each mode of operation. As the design matures, hot-fire tests will be conducted to refine performance estimates and anchor more sophisticated reacting-flow analysis.

Smith, Timothy D.↗
NASA NTRS2015

The Rapid Response Radiation Survey (R3S) Mission Using the HISat Conformal Satellite Architecture

The Rapid Response Radiation Survey (R3S) experiment, designed as a quick turnaround mission to make radiation measurements in LEO, will fly as a hosted payload in partnership with NovaWurks using their Hyper-integrated Satlet (HiSat) architecture. The need for the mission arises as the Nowcast of Atmospheric Ionization Radiation for Aviation Safety (NAIRAS) model moves from a research effort into an operational radiation assessment tool. The data collected by R3S, in addition to the complementary data from a NASA Langley Research Center (LaRC) atmospheric balloon mission entitled Radiation Dosimetry Experiment (RaDX), will validate exposure prediction capabilities of NAIRAS. This paper discusses the development of the R3S experiment as made possible by use of the HiSat architecture. The system design and operational modes of the experiment are described, as well as the experiment interfaces to the HiSat satellite via the user defined adapter (UDA) provided by NovaWurks. This paper outlines the steps taken by the project to execute the R3S mission in the 4 months of design, build, and test. Finally, description of the engineering process is provided, including the use of facilitated rapid/concurrent engineering sessions, the associated documentation, and the review process employed.

Miller, Nathanael↗
NASA NTRS1975

Supplement to the 1975 report on active and planned spacecraft and experiments

A listing and brief description of spacecraft and experiments designed to update the January 1975 report on active and planned spacecraft and experiments to March 31, 1975 was presented. The information is given in two sections. In the first, spacecraft and experiments that have become known to NSSDC since the original report or that have changed significantly are described. In the second, an alphabetical listing is given for all spacecraft and experiments described in the first section and in the original report. It also updates status of operation and launch dates to March 31, 1975.

Horowitz, R.↗
NASA NTRS1989

Designers as users - Design supports based on crew system design practices

The behavioral processes in aviation crew system design are theoretically discussed. Interviews with designers concerning actual design experiences were conducted in a structured manner, focusing on the nature of the design problem, the designers's tasks, how decisions governing the human operator's role are made, and how this decision making can be supported. Two taxonomies emerge, one of which summarizes the nature of the design problem and the second of which summarizes the tasks that designers perform toward solving the problem. Combining the taxonomies yields a design problem space that is used to classify existing forms of support. The results of this classification and the implications for needed supports are discussed.

Cody, William J.↗
NASA NTRS1993

Development Of Infrared Imager For Spacelab

Terrestrial instrument modified for use in outer space. Report discusses progress in development of infrared-imaging instrument for use in microgravity scientific experiments in manned module in payload bay of Space Shuttle. Imager intended primarily for characterization of surface temperatures in microgravity fluid-physics experiment. Design versatile so instrument serves as "off-the-shelf" unit for other experiments, eliminating need to duplicate development and qualifications for spacecraft for future experiments.

Pline, Alexander D.↗
NASA NTRS1992

An overview of the first International Satellite Land Surface Climatology Project (ISLSCP) Field Experiment (FIFE)

This paper reviews the history and scientific background leading up to FIFE, the experiment design, the scientific teams and equipment involved, and the actual execution of the experiment. The experiment was tasked with exploring techniques for utilizing satellite data to quantify important biophysical states and rates for model input. During the intensive field campaigns the fluxes of moisture, heat, carbon dioxide and radiation were measured with airborne and surface equipment in coordination with measurements of atmospheric and surface parameters and satellite overpasses.

Sellers, P. J.↗
NASA NTRS1976

Spacelab payload accommodation handbook. Preliminary issue

The main characteristics of the Spacelab system are described. Sufficient information on Spacelab capabilities is provided to enable individual experimenters or payload planning groups to determine how their payload equipment can be accomodated by Spacelab topics discussed include major spacelab/experiment interfaces; Spacelab payload support systems and requirements the experiments must comply with to allow experiment design; and development and integration up to a level where a group of individual experiments are integrated into a complete Spacelab payload using Spacelab racks/floors and pallet segments. Integration of a complete Spacelab payload with Spacelab subsystems, primary module structure etc., integration of Spacelab with the Orbiter and basic operational aspects are also covered in this preliminary edition of the handbook which reflects the current Spacelab baseline design and is for information only.

Source record↗
NASA NTRS2010

HIFiRE Direct-Connect Rig (HDCR) Phase I Ground Test Results from the NASA Langley Arc-Heated Scramjet Test Facility

The initial phase of hydrocarbon-fueled ground tests supporting Flight 2 of the Hypersonic International Flight Research Experiment (HIFiRE) Program has been conducted in the NASA Langley Arc-Heated Scramjet Test Facility (AHSTF). The HIFiRE Program, an Air Force-lead international cooperative program includes eight different flight test experiments designed to target specific challenges of hypersonic flight. The second of the eight planned flight experiments is a hydrocarbon-fueled scramjet flight test intended to demonstrate dual-mode to scramjet-mode operation and verify the scramjet performance prediction and design tools. A performance goal is the achievement of a combusted fuel equivalence ratio greater than 0.7 while in scramjet mode. The ground test rig, designated the HIFiRE Direct Connect Rig (HDCR), is a full-scale, heat sink, direct-connect ground test article that duplicates both the flowpath lines and the instrumentation layout of the isolator and combustor portion of the flight test hardware. The primary objectives of the HDCR Phase I tests are to verify the operability of the HIFiRE isolator/combustor across the Mach 6.0-8.0 flight regime and to establish a fuel distribution schedule to ensure a successful mode transition prior to the HiFIRE payload Critical Design Review. Although the phase I test plans include testing over the Mach 6 to 8 flight simulation range, only Mach 6 testing will be reported in this paper. Experimental results presented here include flowpath surface pressure, temperature, and heat flux distributions that demonstrate the operation of the flowpath over a small range of test conditions around the nominal Mach 6 simulation, as well as a range of fuel equivalence ratios and fuel injection distributions. Both ethylene and a mixture of ethylene and methane (planned for flight) were tested. Maximum back pressure and flameholding limits, as well as a baseline fuel schedule, that covers the Mach 5.84-6.5 test space have been identified.

Hass, Neal E.↗
NASA NTRS1972

The liquid metal slip ring experiment for the Communications Technology Satellite.

Description of an experiment designed to demonstrate liquid metal slip ring (LMSR) performance in a space environment. The experiment, based on currently developed LMSR technology, is to make possible an evaluation of those features of a LMSR where improvement in performance over conventional slip rings might be feasible. The experiment-prompting, potential LMSR advantages include: lower electrical noise, higher current capability, higher voltage capability, longer life, and small variation in friction torque.

Lovell, R. R.↗
NASA NTRS1992

Be-Cu precipitation hardening experiment

The following is a laboratory experiment designed to further a student's understanding of materials science. The student performing this experiment should have a knowledge of binary phase diagrams. The objectives of this experiment are as follows: (1) to give the student a hands-on approach to changing materials properties through heat treatment of a specimen; (2) to quantify the amount of strengthening obtained in the specimen; and (3) to encourage the student to speculate about the structural changes that have occurred in the material to cause the changes in strength.

Cowan, Richard L.↗
NASA NTRS1992

Numerical simulation of unsteady flow in a hypersonic shock tunnel facility

This paper describes the computational work performed on the simulation of a 16-in shock-tunnel facility. The numerical problems encountered during the computation of these flows are discussed along with the validity of some approximations used, notably concerning the reduction of the problem into problems of smaller dimensionality. Quasi-1D simulations can be used to help design experiments, or to better understanding the characteristics of the facility. An application to the design of a nonintrusive diagnostic is shown. The multidimensional flow transients computed include the shock reflection at the end of the driven tube, the shock propagation down the nozzle, and the breaking of the main diaphragm.

Cambier, Jean-Luc↗
NASA NTRS1994

Topography and tectonics of the central New Madrid seismic zone: Results of numerical experiements using a three-dimensional boundary element program

We present results of a series of numerical experiments designed to test hypothetical mechanisms that derive deformation in the New Madrid seismic zone. Experiments are constrained by subtle topography and the distribution of seismicity in the region. We use a new boundary element algorithm that permits calcuation of the three-dimensional deformation field. Surface displacement fields are calculated for the New Madrid zone under both far-field (plate tectonics scale) and locally derived driving strains. Results demonstrate that surface displacement fields cannot distinguish between either a far-field simple or pure shear strain field or one that involves a deep shear zone beneath the upper crustal faults. Thus, neither geomorphic nor geodetic studies alone are expected to reveal the ultimate driving mechanism behind the present-day deformation. We have also tested hypotheses about strain accommodation within the New Madrid contractional step-over by including linking faults, two southwest dipping and one vertical, recently inferred from microearthquake data. Only those models with step-over faults are able to predict the observed topography. Surface displacement fields for long-term, relaxed deformation predict the distribution of uplift and subsidence in the contractional step-over remarkably well. Generation of these displacement fields appear to require slip on both the two northeast trending vertical faults and the two dipping faults in the step-over region, with very minor displacements occurring during the interseismic period when the northeast trending vertical faults are locked. These models suggest that the gently dippling central step-over fault is a reverse fault and that the steeper fault, extending to the southeast of the step-over, acts as a normal fault over the long term.

Gomberg, Joan↗
NASA NTRS2003

Multiple Input Design for Real-Time Parameter Estimation in the Frequency Domain

A method for designing multiple inputs for real-time dynamic system identification in the frequency domain was developed and demonstrated. The designed inputs are mutually orthogonal in both the time and frequency domains, with reduced peak factors to provide good information content for relatively small amplitude excursions. The inputs are designed for selected frequency ranges, and therefore do not require a priori models. The experiment design approach was applied to identify linear dynamic models for the F-15 ACTIVE aircraft, which has multiple control effectors.

Morelli, Eugene↗
NASA NTRS2016

AirSTAR Hardware and Software Design for Beyond Visual Range Flight Research

The National Aeronautics and Space Administration (NASA) Airborne Subscale Transport Aircraft Research (AirSTAR) Unmanned Aerial System (UAS) is a facility developed to study the flight dynamics of vehicles in emergency conditions, in support of aviation safety research. The system was upgraded to have its operational range significantly expanded, going beyond the line of sight of a ground-based pilot. A redesign of the airborne flight hardware was undertaken, as well as significant changes to the software base, in order to provide appropriate autonomous behavior in response to a number of potential failures and hazards. Ground hardware and system monitors were also upgraded to include redundant communication links, including ADS-B based position displays and an independent flight termination system. The design included both custom and commercially available avionics, combined to allow flexibility in flight experiment design while still benefiting from tested configurations in reversionary flight modes. A similar hierarchy was employed in the software architecture, to allow research codes to be tested, with a fallback to more thoroughly validated flight controls. As a remotely piloted facility, ground systems were also developed to ensure the flight modes and system state were communicated to ground operations personnel in real-time. Presented in this paper is a general overview of the concept of operations for beyond visual range flight, and a detailed review of the airborne hardware and software design. This discussion is held in the context of the safety and procedural requirements that drove many of the design decisions for the AirSTAR UAS Beyond Visual Range capability.

Laughter, Sean↗
NASA NTRS1986

Modified Petri net model sensitivity to workload manipulations

Modified Petri Nets (MPNs) are investigated as a workload modeling tool. The results of an exploratory study of the sensitivity of MPNs to work load manipulations in a dual task are described. Petri nets have been used to represent systems with asynchronous, concurrent and parallel activities (Peterson, 1981). These characteristics led some researchers to suggest the use of Petri nets in workload modeling where concurrent and parallel activities are common. Petri nets are represented by places and transitions. In the workload application, places represent operator activities and transitions represent events. MPNs have been used to formally represent task events and activities of a human operator in a man-machine system. Some descriptive applications demonstrate the usefulness of MPNs in the formal representation of systems. It is the general hypothesis herein that in addition to descriptive applications, MPNs may be useful for workload estimation and prediction. The results are reported of the first of a series of experiments designed to develop and test a MPN system of workload estimation and prediction. This first experiment is a screening test of MPN model general sensitivity to changes in workload. Positive results from this experiment will justify the more complicated analyses and techniques necessary for developing a workload prediction system.

White, S. A.↗
NASA NTRS1987

Guided-wave approaches to spectrally selective energy absorption

Results of experiments designed to demonstrate spectrally selective absorption in dielectric waveguides on semiconductor substrates are reported. These experiments were conducted with three waveguides formed by sputtering films of PSK2 glass onto silicon-oxide layers grown on silicon substrates. The three waveguide samples were studied at 633 and 532 nm. The samples differed only in the thickness of the silicon-oxide layer, specifically 256 nm, 506 nm, and 740 nm. Agreement between theoretical predictions and measurements of propagation constants (mode angles) of the six or seven modes supported by these samples was excellent. However, the loss measurements were inconclusive because of high scattering losses in the structures fabricated (in excess of 10 dB/cm). Theoretical calculations indicated that the power distribution among all the modes supported by these structures will reach its steady state value after a propagation length of only 1 mm. Accordingly, the measured loss rates were found to be almost independent of which mode was initially excited. The excellent agreement between theory and experiment leads to the conclusion that low loss waveguides confirm the predicted loss rates.

Stegeman, G. I.↗
NASA NTRS1993

Design and implementation of fuzzy logic controllers

The main objectives of our research are to present a self-contained overview of fuzzy sets and fuzzy logic, develop a methodology for control system design using fuzzy logic controllers, and to design and implement a fuzzy logic controller for a real system. We first present the fundamental concepts of fuzzy sets and fuzzy logic. Fuzzy sets and basic fuzzy operations are defined. In addition, for control systems, it is important to understand the concepts of linguistic values, term sets, fuzzy rule base, inference methods, and defuzzification methods. Second, we introduce a four-step fuzzy logic control system design procedure. The design procedure is illustrated via four examples, showing the capabilities and robustness of fuzzy logic control systems. This is followed by a tuning procedure that we developed from our design experience. Third, we present two Lyapunov based techniques for stability analysis. Finally, we present our design and implementation of a fuzzy logic controller for a linear actuator to be used to control the direction of the Free Flight Rotorcraft Research Vehicle at LaRC.

Abihana, Osama A.↗