Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “core optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Perceived Noise Analysis for Offset Jets Applied to Commercial Supersonic Aircraft

A systems analysis was performed with experimental jet noise data, engineaircraft performance codes and aircraft noise prediction codes to assess takeoff noise levels and mission range for conceptual supersonic commercial aircraft. A parametric study was done to identify viable engine cycles that meet NASAs N+2 goals for noise and performance. Model scale data from offset jets was used as input to the aircraft noise prediction code to determine the expected sound levels for the lateral certification point where jet noise dominates over all other noise sources. The noise predictions were used to determine the optimal orientation of the offset nozzles to minimize the noise at the lateral microphone location. An alternative takeoff procedure called programmed lapse rate was evaluated for noise reduction benefits. Results show there are two types of engines that provide acceptable range performance; one is a standard mixed-flow turbofan with a single-stage fan, and the other is a three-stream variable-cycle engine with a multi-stage fan. The engine with a single-stage fan has a lower specific thrust and is 8 to 10 EPNdB quieter for takeoff. Offset nozzles reduce the noise directed toward the thicker side of the outer flow stream, but have less benefit as the core nozzle pressure ratio is reduced and the bypass-to-core area ratio increases. At the systems level for a three-engine N+2 aircraft with full throttle takeoff, there is a 1.4 EPNdB margin to Chapter 3 noise regulations predicted for the lateral certification point (assuming jet noise dominates). With a 10 reduction in thrust just after takeoff rotation, the margin increases to 5.5 EPNdB. Margins to Chapter 4 and Chapter 14 levels will depend on the cumulative split between the three certification points, but it appears that low specific thrust engines with a 10 reduction in thrust (programmed lapse rate) can come close to meeting Chapter 14 noise levels. Further noise reduction is possible with additional reduction in takeoff thrust using programmed lapse rate, but studies are needed to investigate the practical limits for safety and takeoff regulations.

Jet Noise↗

Automatic Generation of Algorithms for the Statistical Analysis of Planetary Nebulae Images

Analyzing data sets collected in experiments or by observations is a Core scientific activity. Typically, experimentd and observational data are &aught with uncertainty, and the analysis is based on a statistical model of the conjectured underlying processes, The large data volumes collected by modern instruments make computer support indispensible for this. Consequently, scientists spend significant amounts of their time with the development and refinement of the data analysis programs. AutoBayes [GF+02, FS03] is a fully automatic synthesis system for generating statistical data analysis programs. Externally, it looks like a compiler: it takes an abstract problem specification and translates it into executable code. Its input is a concise description of a data analysis problem in the form of a statistical model as shown in Figure 1; its output is optimized and fully documented C/C++ code which can be linked dynamically into the Matlab and Octave environments. Internally, however, it is quite different: AutoBayes derives a customized algorithm implementing the given model using a schema-based process, and then further refines and optimizes the algorithm into code. A schema is a parameterized code template with associated semantic constraints which define and restrict the template s applicability. The schema parameters are instantiated in a problem-specific way during synthesis as AutoBayes checks the constraints against the original model or, recursively, against emerging sub-problems. AutoBayes schema library contains problem decomposition operators (which are justified by theorems in a formal logic in the domain of Bayesian networks) as well as machine learning algorithms (e.g., EM, k-Means) and nu- meric optimization methods (e.g., Nelder-Mead simplex, conjugate gradient). AutoBayes augments this schema-based approach by symbolic computation to derive closed-form solutions whenever possible. This is a major advantage over other statistical data analysis systems which use numerical approximations even in cases where closed-form solutions exist. AutoBayes is implemented in Prolog and comprises approximately 75.000 lines of code. In this paper, we take one typical scientific data analysis problem-analyzing planetary nebulae images taken by the Hubble Space Telescope-and show how AutoBayes can be used to automate the implementation of the necessary anal- ysis programs. We initially follow the analysis described by Knuth and Hajian [KHO2] and use AutoBayes to derive code for the published models. We show the details of the code derivation process, including the symbolic computations and automatic integration of library procedures, and compare the results of the automatically generated and manually implemented code. We then go beyond the original analysis and use AutoBayes to derive code for a simple image segmentation procedure based on a mixture model which can be used to automate a manual preproceesing step. Finally, we combine the original approach with the simple segmentation which yields a more detailed analysis. This also demonstrates that AutoBayes makes it easy to combine different aspects of data analysis.

Fischer, Bernd↗

Spitzer Space Telescope Sequencing Operations Software, Strategies, and Lessons Learned

The Space Infrared Telescope Facility (SIRTF) was launched in August, 2003, and renamed to the Spitzer Space Telescope in 2004. Two years of observing the universe in the wavelength range from 3 to 180 microns has yielded enormous scientific discoveries. Since this magnificent observatory has a limited lifetime, maximizing science viewing efficiency (ie, maximizing time spent executing activities directly related to science observations) was the key operational objective. The strategy employed for maximizing science viewing efficiency was to optimize spacecraft flexibility, adaptability, and use of observation time. The selected approach involved implementation of a multi-engine sequencing architecture coupled with nondeterministic spacecraft and science execution times. This approach, though effective, added much complexity to uplink operations and sequence development. The Jet Propulsion Laboratory (JPL) manages Spitzer s operations. As part of the uplink process, Spitzer s Mission Sequence Team (MST) was tasked with processing observatory inputs from the Spitzer Science Center (SSC) into efficiently integrated, constraint-checked, and modeled review and command products which accommodated the complexity of non-deterministic spacecraft and science event executions without increasing operations costs. The MST developed processes, scripts, and participated in the adaptation of multi-mission core software to enable rapid processing of complex sequences. The MST was also tasked with developing a Downlink Keyword File (DKF) which could instruct Deep Space Network (DSN) stations on how and when to configure themselves to receive Spitzer science data. As MST and uplink operations developed, important lessons were learned that should be applied to future missions, especially those missions which employ command-intensive operations via a multi-engine sequence architecture.

missions operations↗

Design and Assembly of an Integrated Metabolic Heat Regenerated Temperature Swing Adsorption (MTSA) Subassembly Engineering Development Unit

Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO2) control for a Portable Life Support System (PLSS), as well as water recycling. The core of the MTSA technology is a sorbent bed that removes CO2 from the PLSS ventilation loop gas via a temperature swing. A Condensing Icing Heat eXchanger (CIHX) is used to warm the sorbent while also removing water from the ventilation loop gas. A Sublimation Heat eXchanger (SHX) is used to cool the sorbent. Research was performed to explore an MTSA designed for both lunar and Martian operations. Previously the sorbent bed, CIHX, and SHX had been built and tested individually on a scale relevant to PLSS operations, but they had not been done so as an integrated subassembly. Design and analysis of an integrated subassembly was performed based on this prior experience and an updated transient system model. Focus was on optimizing the design for Martian operations, but the design can also be used in lunar operations. An Engineering Development Unit (EDU) of an integrated MTSA subassembly was assembled based on the design. Its fabrication is discussed. Some details on the differences between the as-assembled EDU and the future flight unit are considered.

Padilla, Sebastian A.↗

Numerical modeling for an electric-field hyperthermia applicator

Hyperthermia, in conjunction with radiation and chemotherapy for treatment of cancers, is an area of current concern. Experiments have shown that hyperthermia can increase the potency of many chemotherapy drugs and the effectiveness of radiation for treating cancer. A combination of whole body or regional hyperthermia with chemotherapy or radiation should improve treatment results. Conventional methods for inducing whole body hyperthermia, such as exposing a patient in a radiant cabinet or under a hot water blanket, conduct heat very slowly from the skin to the body core. Thus a more efficient system, such as the three-plate electric-field hyperthermia applicator (EHA), is developed. This three-plate EHA has one top plate over and two lower plates beneath the patient. It is driven at 27.12 MHz with 500 Watts through a matching circuit. Using this applicator, a 50 kg pig was successfully heated to 42 C within 45 minutes. However, phantom and animal studies have indicated non-uniform heating near the side of the body. In addition, changes in the size and distance between the electrode plates can affect the heating (or electromagnetic field) pattern. Therefore, numerical models using the method of moments (MOM) or the finite difference time domain (FDTD) technique are developed to optimize the heating pattern of this EHA before it is used for human trials. The accuracy of the numerical modeling has been achieved by the good agreement between the MOM and FDTD results for the three-plate EHA without a biological body. The versatile FDTD technique is then applied to optimize the EHA design with a human body. Both the numerical and measured data in phantom blocks will be presented. The results of this study will be used to design an optimized system for whole body or regional hyperthermia.

Wu, Te-Kao↗

Design and Assembly of an Integrated Metabolic Heat Regenerated Temperature Swing Adsorption (MTSA) Subassembly Engineering Development Unit

Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO2) control for a Portable Life Support System (PLSS), as well as water recycling. The core of the MTSA technology is a sorbent bed that removes CO2 from the PLSS ventilation loop gas via a temperature swing. A Condensing Ice Heat eXchanger (CIHX) is used to warm the sorbent while also removing water from the ventilation loop gas. A Sublimation Heat eXchanger (SHX) is used to cool the sorbent. Research was performed to explore an MTSA designed for both lunar and Martian operations. Previously each the sorbent bed, CIHX, and SHX had been built and tested individually on a scale relevant to PLSS operations, but they had not been done so as an integrated subassembly. Design and analysis of an integrated subassembly was performed based on this prior experience and an updated transient system model. Focus was on optimizing the design for Martian operations, but the design can also be used in lunar operations. An Engineering Development Unit (EDU) of an integrated MTSA subassembly was assembled based on the design. Its fabrication is discussed. Some details on the differences between the as-assembled EDU to the future flight unit are considered.

Padilla, Sebastian A.↗

Onboard Autonomous Trajectory Planning for Mars Power Descent

In recent years, there has been an increasing interest in space-qualified processors such as multi-core central processing units and graphics processing units that can withstand the adverse effects of space radiation. These processors can allow parallel programming to perform tasks that typically demand high computational power. One can study guidance schemes that can take advantage of these currently developing processors and provide more robust guidance. Software for Multi-model Autonomous Real-time Trajectories (SMART) guidance can identify robust trajectories by running an onboard Monte Carlo analysis. SMART guidance can take advantage of knowledge updates obtained from the onboard sensors, allowing it to consider the off-nominal cases that it would not typically encounter during the offline trajectory analysis. This work uses the SMART guidance for the powered divert at Mars simulation in Program to Optimize and Simulated Trajectories- II.

Pardha Sai Chadalavada↗

Onboard Autonomous Trajectory Planning for Mars Power Descent

In recent years, there has been an increasing interest in space-qualified processors such as multi-core central processing units and graphics processing units that can withstand the adverse effects of space radiation. These processors can allow parallel programming to perform tasks that typically demand high computational power. One can study guidance schemes that can take advantage of these currently developing processors and provide more robust guidance. Software for Multi-model Autonomous Real-time Trajectories (SMART) guidance can identify robust trajectories by running an onboard Monte Carlo analysis. SMART guidance can take advantage of knowledge updates obtained from the onboard sensors, allowing it to consider the off-nominal cases that it would not typically encounter during the offline trajectory analysis. This work uses the SMART guidance for the powered divert at Mars simulation in Program to Optimize and Simulated Trajectories- II.

Autonomous Planning↗

Conductive Tether Coating for Electrodynamic Tethers

The Propulsive Small Expendable Deployer System (ProSEDS), which is an on-orbit demonstration of the propulsion capabilities of electrodynamic tethers in space, is a secondary payload on a Delta 11 unmanned expendable booster. The ProSEDS tether consists of a 5 km bare electrodynamic tether and a 1 0-km non-conductive leader tether. Near the Delta 11, 160 m of the conductive tether is insulated to prevent plasma electron collection from the plasma contactor and for other science requirements. The remainder of the 5-km conductive tether is coated with a new conductive coating to collect plasma electrons. A bare metal tether easily collects electrons from the plasma, but thermal concerns preclude this design. A highly emissive conductive polymer developed by Triton Systems, Inc. has been optimized for both conductivity and thermo-optical properties. The current design for the ProSEDS conductive tether is seven individually coated strands of 28 AWG aluminum wire, coated with an atomic oxygen-resistant conductive polymer composed of a mixture of COR (Colorless Oxygen Resistant) and polyanaline (PANI) known as C-COR (Conductive-Colorless Oxygen Resistant). The conductive-coated wire strands are cold-welded to individually coated strands of the insulated tether. The insulated tether is coated with 1 mil of polyimide and an atomic oxygen resistant polymer TOR-BP. The insulated tether must stand off the entire voltage of the tether (1 200 V) at various times during the mission. All seven wires are twisted around a Kevlar-29 core using the Hi-wire design. Extensive testing has been performed at the Marshall Space Flight Center to qualify both the conductive coating and insulating coating for use on the ProSEDS tether. The conductive coating has been exposed to a plasma to verify the coatings ability to collect electrons from the space plasma from 0 to 1500 V, and to verify the coatings ability to collect electrons after atomic oxygen exposure. The insulated coating has been tested to verify its dielectric strength both in a vacuum and air. Thermal optical properties on both coatings have been measured before and after atomic oxygen testing. The results of these tests will be presented.

Jason A Vaughn↗

PIV Measurements of Chevrons on F400-Series Tactical Aircraft Nozzle Model

Reducing noise of tactical jet aircraft has taken on fresh urgency as core engine technologies allow higher specific-thrust engines and as society become more concerned for the health of its military workforce. Noise reduction on this application has lagged the commercial field as incentives for quieting military aircraft have not been as strong as in their civilian counterparts. And noise reduction strategies employed on civilian engines may not be directly applicable due to the differences in exhaust system architecture and mission. For instance, the noise reduction technology of chevrons, examined in this study, will need to be modified to take into account the special features of tactical aircraft nozzles. In practice, these nozzles have divergent slats that are tied to throttle position, and at take off the jet flow is highly overexpanded as the nozzle is optimized for cruise altitude rather than sea level. In simple oil flow visualization experiments conducted at the onset of the current test program flow barely stays attached at end of nozzle at takeoff conditions. This adds a new twist to the design of chevrons. Upon reaching the nozzle exit the flow shrinks inward radially, meaning that for a chevron to penetrate the flow it must extend much farther away from the baseline nozzle streamline. Another wrinkle is that with a variable divergence angle on the nozzle, the effective penetration will differ with throttle position and altitude. The final note of realism introduced in these experiments was to simulate the manner in which bypass flow is bled into the nozzle wall in real engines to cool the nozzle, which might cause very fat boundary layer at exit. These factors, along with several other issues specific to the application of chevrons to convergent-divergent nozzles have been explored with particle image velocimetry measurements and are presented in this paper.

Bridges, James↗

Atmospheric Mining in the Outer Solar System: Aerial Vehicle Mission and Design Issues

Atmospheric mining in the outer solar system has been investigated as a means of fuel production for high energy propulsion and power. Fusion fuels such as Helium 3 (3He) and deuterium can be wrested from the atmospheres of Uranus and Neptune and either returned to Earth or used in-situ for energy production. Helium 3 and deuterium were the primary gases of interest with hydrogen being the primary propellant for nuclear thermal solid core and gas core rocket-based atmospheric flight. A series of analyses were undertaken to investigate resource capturing aspects of atmospheric mining in the outer solar system. This included the gas capturing rate, storage options, and different methods of direct use of the captured gases. While capturing 3He, large amounts of hydrogen and 4He are produced. With these two additional gases, the potential for fueling small and large fleets of additional exploration and exploitation vehicles exists. The mining aerospacecraft (ASC) could fly through the outer planet atmospheres, for global weather observations, localized storm or other disturbance investigations, wind speed measurements, polar observations, etc. Analyses of orbital transfer vehicles (OTVs), landers, and in-situ resource utilization (ISRU) mining factories are included. Preliminary observations are presented on near-optimal selections of moon base orbital locations, OTV power levels, and OTV and lander rendezvous points.

orbital mechanics↗

A CFD-based aerodynamic design procedure for hypersonic wind-tunnel nozzles

A new procedure which unifies the best of current classical design practices, computational fluid dynamics (CFD), and optimization procedures is demonstrated for designing the aerodynamic lines of hypersonic wind-tunnel nozzles. The new procedure can be used to design hypersonic wind tunnel nozzles with thick boundary layers where the classical design procedure has been shown to break down. An efficient CFD code, which solves the parabolized Navier-Stokes (PNS) equations using an explicit upwind algorithm, is coupled to a least-squares (LS) optimization procedure. A LS problem is formulated to minimize the difference between the computed flow field and the objective function, consisting of the centerline Mach number distribution and the exit Mach number and flow angle profiles. The aerodynamic lines of the nozzle are defined using a cubic spline, the slopes of which are optimized with the design procedure. The advantages of the new procedure are that it allows full use of powerful CFD codes in the design process, solves an optimization problem to determine the new contour, can be used to design new nozzles or improve sections of existing nozzles, and automatically compensates the nozzle contour for viscous effects as part of the unified design procedure. The new procedure is demonstrated by designing two Mach 15, a Mach 12, and a Mach 18 helium nozzles. The flexibility of the procedure is demonstrated by designing the two Mach 15 nozzles using different constraints, the first nozzle for a fixed length and exit diameter and the second nozzle for a fixed length and throat diameter. The computed flow field for the Mach 15 least squares parabolized Navier-Stokes (LS/PNS) designed nozzle is compared with the classically designed nozzle and demonstrates a significant improvement in the flow expansion process and uniform core region.

Korte, John J.↗

Distributed Spacecraft Autonomy (DSA): Development of Swarm Autonomy Capability and Scalability for Spacecraft

The Distributed Spacecraft Autonomy project is developing a suite of software tools that enable an operator to command and receive data from a swarm as a single entity, enable a swarm to autonomously coordinate its actions via distributed decision making and reactive closed-loop control, and model swarm behavior in the presence of anomalies or failures. Our use case is the mapping of the electron density of the ionosphere using radio tomography by coordinating the selection of appropriate GPS channels, and by recording Total Electron Count (TEC)measurements. DSA will be demonstrated on board the NASA Ames Starling mission a swarm of four small, LEO spacecraft, scheduled to launch in 2021. We will also perform a ground demonstration with simulated and hardware-in-the-loop elements, to validate the tools for controlling swarms of up to 100 assets.The capability to communicate autonomously between the swarm satellites is demonstrated via a sophisticated simulation architecture. Historical Plasma sphere TEC data obtained via dual-band Novatel GPS Receivers are utilized as a representative input data set for the swarm. The representative TEC data and GPS satellite observability information is fed to the autonomous software package in place of a true real-time ground data collection process. The swarm satellites actively share status updates amongst one another and utilize multi-agent decision making to optimally identify regions of interest in the TEC distribution. The software,aware of the bandwidth limitations of the swarm satellites, prioritizes explorative measurements,which define the range of observability for the satellites, as well as exploitative measurements,which focus on maximizing the observance potential of regions with prolonged, elevated TEC density. The science of this study can ultimately be used to determine the dynamics and coupling of Earth's magnetosphere, ionosphere, and atmosphere and their response to solar and terrestrial inputs. The findings can be applied to the imaging of critical, transient phenomena in the magnetosphere in later missions. Meanwhile, the swarm autonomy capabilities have far reaching potential in future satellite missions.As an experimental demonstration of the autonomous capabilities of the network, a message is first printed within a core Flight Executive (cFE) application. Two cFE applications that communicate with one another within the same core Flight System (cFS) are shown.Communication between mission applications on the internal cFE bus is extended to utilize Data Distribution Service (DDS) for vehicle-to-vehicle networking. The DDS middle ware provides reliable delivery, routing, and topic subscription features over User Data gram Protocol (UDP).Leveraging Linux containerization, a networked set of satellite instances are generated by script to simulate swarm behavior. Swarm commanding and synchronization through the network is demonstrated under various topologies and data-loss conditions. Finally, autonomous swarms calability from 2 satellites to 100 satellites is shown.

Fugate, Jason↗

Distributed Spacecraft Autonomy - Development of Swarm Autonomy Capability and Scalability for Spacecraft

The Distributed Spacecraft Autonomy project is developing a suite of software tools that enable an operator to command and receive data from a swarm as a single entity, enable a swarm to autonomously coordinate its actions via distributed decision making and reactive closed-loop control, and model swarm behavior in the presence of anomalies or failures. Our use case is the mapping of the electron density of the ionosphere using radio tomography by coordinating the selection of appropriate GPS channels, and by recording Total Electron Count (TEC) measurements. DSA will be demonstrated onboard the NASA Ames Starling mission – a swarm of four small, LEO spacecraft, scheduled to launch in 2021. We will also perform a ground demonstration with simulated and hardware-in-the-loop elements, to validate the tools for controlling swarms of up to 100 assets. The capability to communicate autonomously between the swarm satellites is demonstrated via a sophisticated simulation architecture. Historical Plasmasphere TEC data obtained via dual-band Novatel GPS Receivers are utilized as a representative input dataset for the swarm. The representative TEC data and GPS satellite observability information is fed to the autonomous software package in place of a true real-time ground data collection process. The swarm satellites actively share status updates amongst one another and utilize multi-agent decision making to optimally identify regions of interest in the TEC distribution. The software, aware of the bandwidth limitations of the swarm satellites, prioritizes explorative measurements, which define the range of observability for the satellites, as well as exploitative measurements, which focus on maximizing the observance potential of regions with prolonged, elevated TEC density. The science of this study can ultimately be used to determine the dynamics and coupling of Earth’s magnetosphere, ionosphere, and atmosphere and their response to solar and terrestrial inputs. The findings can be applied to the imaging of critical, transient phenomena in the magnetosphere in later missions. Meanwhile, the swarm autonomy capabilities have far reaching potential in future satellite missions. As an experimental demonstration of the autonomous capabilities of the network, a message is first printed within a core Flight Executive (cFE) application. Two cFE applications that communicate with one another within the same core Flight System (cFS) are shown. Communication between mission applications on the internal cFE bus is extended to utilize Data Distribution Service (DDS) for vehicle-to-vehicle networking. The DDS middleware provides reliable delivery, routing, and topic subscription features over User Datagram Protocol (UDP). Leveraging Linux containerization, a networked set of satellite instances are generated by script to simulate swarm behavior. Swarm commanding and synchronization through the network is demonstrated under various topologies and data-loss conditions. Finally, autonomous swarm scalability from 2 satellites to 100 satellites is shown.

Distributed Autonomy↗

Development of a Data Fusion Methodology for Lineload Aerodynamic Databases for a Launch Vehicle during Liftoff and Transition

The need for databases for the distributed loading on launch vehicles during the early portion of flight necessitates the use of expensive computational flows in regimes where wake effects dominate. While also being expensive, this is a regime that computational tools tend to historically have problems simulating accurately. To help tackle this problem, a method of data fusion to combine computational results to wind tunnel derived force and moment data is developed. Using this method, significant reduction in computational costs and increases in confidence of the final product is possible and has been used to generate several databases for the Space Launch System (SLS) at NASA. While the full details of database generation are not part of this work, the crucial method at its core is developed here. Two SLS geometries are used throughout the work to demonstrate the techniques. These are two of the larger geometries and represent both planned crewed missions to the Moon as well as potential cargo missions to deep space. The method uses principal component analysis (PCA) to generate a reduced ordered model (ROM) to help fill in the full parameter space. Other similar techniques are explored, but were not found to have a significant result on the predictions of the ROM. Because the full number of components are kept to generate the model, this lack of difference is expected. This method is then extended to ensure that predicted surfaces match trusted force and moment data derived from wind tunnel testing. This extension is done by setting up a constrained optimization problem in order to minimize the deviation from the surface resolved computational data while still integrating to the desired values. When generating the constrained optimization problem, a weighting factor to balance these competing needs is introduced. The work compares previously introduced weighting terms from similar work to the proposed terms and shows that the previously used terms do not have as desirable behavior in this flow regime. This method is then expanded by developing a technique to incorporate uncertainty quantification into the developed data fusion methodology. This expansion takes a two pronged approach. One examines transferring the uncertainties in the force and moment database and characterizes how those adjustments change the predicted lineloads. The second looks at model form error and looks how rebuilding the model using slightly different data changes the predictions. These two terms are then combined in order to create an uncertainty model that takes both effects into account. The limitations of the proposed methods is then discussed as well as possible techniques to address these shortcomings.

Launch Vehicles↗

Single-Mode WGM Resonators Fabricated by Diamond Turning

A diamond turning process has made possible a significant advance in the art of whispering-gallery-mode (WGM) optical resonators. By use of this process, it is possible to fashion crystalline materials into WGM resonators that have ultrahigh resonance quality factors (high Q values), are compact (ranging in size from millimeters down to tens of microns), and support single electromagnetic modes. This development combines and extends the developments reported in "Few- Mode Whispering-Gallery-Mode Resonators" (NPO-41256), NASA Tech Briefs, Vol. 30, No. 1 (January 2006), page 16a and "Fabrication of Submillimeter Axisymmetric Optical Components" (NPO-42056), NASA Tech Briefs, Vol. 31, No. 5 (May 2007), page 10a. To recapitulate from the first cited prior article: A WGM resonator of this special type consists of a rod, made of a suitable transparent material, from which protrudes a thin circumferential belt of the same material. The belt is integral with the rest of the rod and acts as a circumferential waveguide. If the depth and width of the belt are made appropriately small, then the belt acts as though it were the core of a single-mode optical fiber: the belt and the rod material adjacent to it support a single, circumferentially propagating mode or family of modes. To recapitulate from the second cited prior article: A major step in the fabrication of a WGM resonator of this special type is diamond turning or computer numerically controlled machining of a rod of a suitable transparent crystalline material on an ultrahigh-precision lathe. During the rotation of a spindle in which the rod is mounted, a diamond tool is used to cut the rod. A computer program is used to control stepping motors that move the diamond tool, thereby controlling the shape cut by the tool. Because the shape can be controlled via software, it is possible to choose a shape designed to optimize a resonator spectrum, including, if desired, to limit the resonator to supporting a single mode. After diamond turning, a resonator can be polished to increase its Q. By virtue of its largely automated, computer-controlled nature, the process is suitable for mass production of nominally identical single-mode WGM resonators. In a demonstration of the capabilities afforded by this development, a number of WGM resonators of various designs were fabricated side by side on the surface of a single CaF2 rod (see figure).

Grudinin, Ivan↗

Fiber Reinforcement Architectures of PMCs on the Hygrothermal-Mechanical Performance for Aeropropulsion Applications

A rigid lightweight sandwich support structure, for the combustor chamber of a new generation liquid propellant rocket engine, was designed and fabricated using Polymer Matric Composite (PMC) facesheet on a Ti honeycomb or Carbon foam core. The facesheet consisted of high stiffness carbon fiber, M40JB, and high temperature Polyimides, such as PMR-11-50 and HFPE-II. Six different fiber architectures; 4HS woven fabric, uni-fabric, woven-uni hybrid, stitched woven fabric, stitched uni-fabric and tri-axial braided structures have been investigated for optimum stiffness-thickness-weight-performance design criteria for the hygrothermal-mechanical propulsion service exposure conditions including rapid heating up to 200 F/sec, maximum operating temperature of 600 F, internal pressure up to 100 psi. An extensive property and performance database including dry-wet mechanical properties at both 25 F and 600 F in various loading modes, thermal and physical properties including blistering onset condition was developed for fiber architecture down-selection and design guidelines. Various optimized process methods including vacuum bag compression molding, solvent assistant RTM (SaRTM), resin film infusion (RFI) were utilized for PMC panel fabrication depending on the architecture type. In the case of stitched woven fabric architecture, the optimal stitch pattern was chosen in terms of stitch density and yarn size, based on both in-plane mechanical properties and blistering performance. Potential reduction of the in-plane properties transverse to the line of stitching was also evaluated. Attempt to correlate the experimental results with theoretical micro-mechanics predictions will be presented.

Shin, Eugene↗

Effect of Apex Flap Deflection on Vertical Tail Buffeting

A computational study of the effect of vortex breakdown location on vertical tail buffeting is conducted. The position of the breakdown is modified by employing an apex flap deflected by an experimentally determined optimal angle. The delayed breakdown flow and buffeting response is then compared to the nominal undeflected case. This multidisciplinary problem is solved sequentially for the fluid flow, the elastic tail deformations and the grid displacements. The fluid flow is simulated by time accurately solving the unsteady, compressible, Reynolds-averaged Navier-Stokes equations using an implicit, upwind, flux-difference splitting finite volume scheme. The elastic vibrations of the tails are modeled by uncoupled bending and torsion beam equations. These equations are solved accurately in time using the Galerkin method and a five-stage Runge-Kutta-Verner scheme. The grid for the fluid dynamics calculations is continuously deformed using interpolation functions to disperse the displacements smoothly throughout the computational domain. An angle-of-attack of 35 deg.is chosen such that the wing primary-vortex cores experience vortex breakdown and the resulting turbulent wake flow impinges on tile vertical tails. The dimensions and material properties of the vertical tails are chosen such that the deflections are large enough to insure interaction with the flow, and the natural frequencies are high enough to facilitate a practical computational solution. Results are presented for a baseline uncontrolled buffeting case and a delayed breakdown case in which the apex flap has been deflected 15 deg. The flap was found to be very effective in delaying the breakdown, increasing the location from 50%c to 94%c, which resulted in a 6% increase in lift coefficient and pitching moment. However, the integrated buffet loads and tip responses were roughly equivalent for the two cases.

Massey, Steven J.↗