Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cathode materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Large-scale synthesis of Li{sub 1.2}V{sub 3}O{sub 8} as a cathode material for lithium secondary battery via a soft chemistry route

Layered Li{sub 1.2}V{sub 3}O{sub 8} has been efficiently prepared via a sol-gel method. XRD and particle size analysis indicate that the final product with monoclinic structure consists of homogeneously distributed particles whose sizes are in a very narrow range. There are two different water molecules in the compound according to TGA and DTA. The structural water works as a pillar in the structure and is lost at higher temperature than the combined water. The as-prepared material was also compared with the one synthesized from the conventional solid-state method in terms of their morphology, electrochemistry capacity and electrodynamic characteristics. As a result, the Li{sub 1.2}V{sub 3}O{sub 8} obtained at 300 deg. C for 10 h has excellent electrochemical properties. A high-first discharge capacity of 286.4 mAh/g was observed at a current rate of C/5 between 1.7 and 3.8 V and the structure of Li{sub 1.2}V{sub 3}O{sub 8} remains stable in the subsequent cycles. EIS calculation suggests a better diffusion path for lithium ions in as-prepared material than in the solid-state compound.

36 MATERIALS SCIENCE↗

Organic-Acid-Assisted Fabrication of Low-Cost Li-Rich Cathode Material (Li[Li1/6Fe1/6Ni1/6Mn1/2]O-2) for Lithium-Ion Battery

A novel Li-rich cathode Li[Li1/6Fe1/6Ni1/6Mn1/2]O-2 (0.4Li(2)MnO(3-)0.6LiFe(1/3)Ni(1/3)Mn(1/3)O(2)) was synthesized by a solgel method, which uses citric acid (SC), tartaric acid (ST), or adipic acid (SA) as a chelating agent. The structural, morphological, and electrochemical properties of the prepared samples were characterized by various methods. X-ray diffraction showed that single-phase materials are formed mainly with typical alpha-NaFeO2 layered structure (R3 m), and the SC sample has the lowest Li/Ni cation disorder. The morphological study indicated homogeneous primary particles in good distribution size (100 nm) with small aggregates. The Fe, Ni, and Mn valences were determined by X-ray absorption near-edge structure analysis. In coin cell tests, the initial reversible discharge capacity of an SA electrode was 289.7 mAh g(-1) at the 0.1C rate in the 1.54.8 V voltage range, while an SC electrode showed a better cycling stability with relatively high capacity retention. At the 2C rate, the SC electrode can deliver a discharge capacity of 150 mAh g(-1) after 50 cycles. Differential capacity vs voltage curves were employed to further investigate the electrochemical reactions and the structural change process during cycling. This low-cost, Fe-based compound prepared by the solgel method has the potential to be used as the high capacity cathode material for Liion batteries.

cathode↗

Electrosprayed polyaniline as cathode material for lithium secondary batteries

Doped polyaniline with LiPF{sub 6} is electrosprayed onto aluminum foil using electrospinning technique, and evaluated as cathode active material for application in room-temperature lithium batteries. Doping level is characterized using FTIR and UV-vis spectroscopy. In FTIR Spectra, characteristic peaks of PANI are shifted to lower bands as a result of doping which indicates the effectiveness of doping. Doping level is also confirmed by UV-vis spectra. Surface morphology of the cathode is studied using scanning electron microscope. Electrochemical evaluation of the cell using electrosprayed PANI as cathode show good cycling properties. The cell delivers a high discharge value of 142.5 mAh/g which is about 100% of theoretical capacity, and the capacity is lowered during cycle and reached 61% of theoretical capacity after 50 cycles. The cell delivers a stable but lower discharge capacity at higher C-rates.

36 MATERIALS SCIENCE↗

Origins of Irreversibility in Layered NaNi x Fe y Mn z O 2 Cathode Materials for Sodium Ion Batteries

Layered NaNi x Fe y Mn z O 2 cathode (NFM) is of great interest in sodium ion batteries due to its high theoretical capacity and utilization of abundant, low-cost, environmentally-friendly raw materials. Nevertheless, there remains insufficient understanding on the concurrent local environment evolution in each transition metal (TM) that largely influences the reversibility of the cathode materials upon cycling. In this work, we investigate the reversibility of TM ions in layered NFMs with varying Fe contents and potential windows. Utilizing ex situ synchrotron X-ray absorption near edge spectroscopy (XANES) and extended X-ray absorption fine structure (EXAFS) of pre-cycled samples the valence and bonding evolution of the TMs are elucidated. It is found that Mn is electrochemically inactive as indicated by the insignificant change of Mn valence and Mn-O bonding distance. Fe is electrochemically inactive after the first five cycles. The Ni redox couple contributes most of the charge compensation for NFMs. Ni redox is quite reversible in the cathodes with less Fe contents. Furthermore, the Ni redox couple shows significant irreversibility with high Fe content of 0.8. The electrochemical reversibility of the NFM cathode becomes increasingly enhanced with the decrease of either Fe content or with lower upper charge cutoff potential.

25 ENERGY STORAGE↗

Developing rapid electrochemical relithiation protocols for scalable relithiation of lithium-ion battery cathode materials

The recent and ongoing boom in electric vehicle sales has caused the circularity of the supply chain for electric vehicle battery materials to come under a great deal of scrutiny. Innovative recycling processes, or direct recycling, that offer the possibility of reducing the cost of recycling are one possible solution to regaining resources from end-of-life (EoL) electric vehicle batteries. Electrochemically shuttling lithium back into the cathode, or electrochemical relithiation, is a possible technique for restoring lithium content to NMC materials (EoL) in a direct recycling process. This study provides essential understanding towards developing an electrochemical relithiation protocol that will restore lithium loss in intercalation cathode materials that reach EoL by loss of lithium inventory (LLI) as opposed to other degradation mechanisms like loss of active material (LAM), cation mixing or phase transition. Electrochemically aged NMC cathode materials have been prepared and characterized to establish the extent of EoL material structural degradation and lithium loss. A model-informed experimental process is used to identify the optimal electrochemical relithiation protocol to minimize the time taken to relithiate EoL materials and maximize the amount of lithium restored. Protocols were evaluated based on their ability to enable rapid lithium intercalation, maintain structural uniformity in the EoL material and fully restore lithium content. An optimal protocol was identified at elevated temperatures utilizing a novel scanning voltage step.

25 ENERGY STORAGE↗

Electrochemical properties of lithium polymer batteries with doped polyaniline as cathode material

Graphical abstract: -- Abstract: Polyaniline (PANI) was doped with different lithium salts such as LiPF{sub 6} and LiClO{sub 4} and evaluated as cathode-active material for application in room-temperature lithium batteries. The doped PANI was characterized by FTIR and XPS measurements. In the FTIR spectra, the characteristic peaks of PANI are shifted to lower bands as a consequence of doping, and it is more shifted in the case of PANI doped with LiPF{sub 6}. The cathodes prepared using PANI doped with LiPF{sub 6} and LiClO{sub 4} delivered initial discharge capacities of 125 mAh g{sup −1} and 112 mAh g{sup −1} and stable reversible capacities of 114 mAh g{sup −1} and 81 mAh g{sup −1}, respectively, after 10 charge–discharge cycles. The cells were also tested using polymer electrolyte, which delivered highest discharge capacities of 142.6 mAh g{sup −1} and 140 mAh g{sup −1} and stable reversible capacities of 117 mAh g{sup −1} and 122 mAh g{sup −1} for PANI-LiPF{sub 6} and PANI-LiClO{sub 4}, respectively, after 10 cycles. The cathode prepared with LiPF{sub 6} doped PANI shows better cycling performance and stability as compared to the cathode prepared with LiClO{sub 4} doped PANI using both liquid and polymer electrolytes.

36 MATERIALS SCIENCE↗

Electrode Separation and Froth Flotation for the Recovery of Li-ion Battery Cathode Materials

Increasing use of Li-ion batteries (LIBs) will significantly increase the quantity of LIB waste generated from end-of-life batteries. Spent LiCoO 2 (LCO) battery cathodes contain significant quantities of valuable metals, making them good candidates for recycling. Typical recycling processes rely on high temperatures (pyrometallurgy) and chemical leachants (hydrometallurgy) to completely decompose the cathode and enable material recovery. Direct recycling processes and recovery of active material from electrode scrap do not benefit from such destructive recycling, and an efficient means of separating the cathode active material from the inactive components (e.g., polyvinylidene fluoride (PVDF) binder, conductive carbon) is needed. Here, we explore PVDF removal from LCO cathodes by two separate methods, evaluating their suitability for coupling to subsequent separation by froth flotation (FF). We show that washing electrodes in the solvent PolarClean (PC) dissolves PVDF away from LCO cathodes, enabling separation of the remaining LCO and conductive carbon by FF. The process is suitable for use with both pristine and cycled LCO electrodes, and the pristine recovered material can be used to prepare electrodes capable of cycling at 140 mAh/g. In conclusion, this demonstrates the suitability of coupled PC washing and FF separation for recycling both end-of-life batteries and scrap electrode material.

Batteries↗

Influence of the synthesis method on the porosity, microstructure and electrical properties of La{sub 0.7}Sr{sub 0.3}MnO{sub 3} cathode materials

Lanthanum strontium manganite (La{sub 1-x}Sr{sub x}MnO{sub 3}, LSM) has been studied as a promising material for application as a cathode in solid oxide fuel cells. In the present work La{sub 0.7}Sr{sub 0.3}MnO{sub 3} nanopowders were synthesized by three different methods (combustion, citrate and solid-state) and characterized by thermal analysis, X-ray diffraction, physical adsorption of N{sub 2} and scanning electron microscopy. All powders exhibited single LSM phase formation with crystallite sizes in the range of 12-20 nm. Nanopowders were sintered at 1100 deg. C to produce porous pellets. The porosity, particle size and microstructure of LSM sintered bodies are strongly dependent on the preparation methodology. The samples synthesized by combustion and citrate methods presented smaller particle sizes and higher porosity after sintering than that derived from solid-state synthesis. However, the electrical conductivity, measured by two-probe technique, was very similar for all three samples.

36 MATERIALS SCIENCE↗

Turning Waste Chemicals into Wealth—A New Approach To Synthesize Efficient Cathode Material for an Li–O 2 Battery

An Li–O 2 battery requires the oxygen-breathing cathode to be highly electronically conductive, rapidly oxygen diffusive, structurally stable, and often times electrocatalytically active. Catalyst-decorated porous carbonaceous materials are the chosen air cathode in this regard. Alternatively, biomass-derived carbonaceous materials possess great ability to remove heavy and toxic metal ions from waste, forming a metal-adsorbed porous carbonaceous material. The similar structure between the air cathode and the metal-adsorbed biomass-derived carbon nicely bridges these two irrelevant areas. In this study, we investigated the electrochemical activity of a biochar material Ag-ESB directly synthesized from ethanol sludge residue in a rechargeable aprotic Li–O 2 battery. Ag ions were adsorbed from sewage and became Ag nanoparticles with uniform coverage on the biochar surface. The as-prepared material exhibits good electrochemical behavior in battery testing, especially toward the battery efficiency and cyclability. This study provides the possibility of synthetically efficient cathode material by reusing “waste” such as biofuel sludge residue. It is an economically and environmentally friendly approach both for an energy-storage system and for waste recycling.

25 ENERGY STORAGE↗

Optimized In Situ Doping Strategy Stabling Single-Crystal Ultrahigh-Nickel Layered Cathode Materials

Single-crystal Ni-rich cathodes offer promising prospects in mitigating intergranular microcracks and side reaction issues commonly encountered in conventional polycrystalline cathodes. However, the utilization of micrometer-sized single-crystal particles has raised concerns about sluggish Li + diffusion kinetics and unfavorable structural degradation, particularly in high Ni content cathodes. Herein, we present an innovative in situ doping strategy to regulate the dominant growth of characteristic planes in the singlecrystal precursor, leading to enhanced mechanical properties and effectively tackling the challenges posed by ultrahigh-nickel layered cathodes. Compared with the traditional dry-doping method, our in situ doping approach possesses a more homogeneous and consistent modifying effect from the inside out, ensuring the uniform distribution of doping ions with large radius (Nb, Zr, W, etc). Further, this mitigates the generally unsatisfactory substitution effect, thereby minimizing undesirable coating layers induced by different solubilities during the calcination process. Additionally, the uniformly dispersed ions from this in situ doping are beneficial for alleviating the two-phase coexistence of H2/H3 and optimizing the Li + concentration gradient during cycling, thus inhibiting the formation of intragranular cracks and interfacial deterioration. Consequently, the in situ doped cathodes demonstrate exceptional cycle retention and rate performance under various harsh testing conditions. Our optimized in situ doping strategy not only expands the application prospects of elemental doping but also offers a promising research direction for developing high-energy-density single-crystal cathodes with extended lifetime.

25 ENERGY STORAGE↗

Resolving Charge Distribution for Compositionally Heterogeneous Battery Cathode Materials

The isostructural nature of Li-layered cathodes allows for accommodating multiple transition metals (TMs). However, little is known about how the local TM stoichiometry influences the charging behavior of battery particles thus impacting battery performance. In this work, we develop heterogeneous compositional distributions in polycrystalline LiNi 1–x–y Mn x Co y O 2 (NMC) particles to investigate the interplay between local stoichiometry and charge distribution. These NMC particles exhibit a broad, continuous distribution of local Ni/Mn/Co stoichiometry, which does not compromise the global layeredness. The local Mn and Ni concentrations in individual NMC particles are positively and negatively correlated with the electrochemically induced Ni oxidation, respectively, whereas the Co concentration does not impose a clear effect on the Ni oxidation. The resulting material delivers excellent reversible capacity, rate capability, and cycle life at high operating voltages. Engineering Ni/Mn/Co distribution in NMC particles may provide a path toward controlling the charge distribution and thus chemomechanical properties of polycrystalline battery particles.

25 ENERGY STORAGE↗

Narrowing the Gap between Theoretical and Practical Capacities in Li-Ion Layered Oxide Cathode Materials

Although layered lithium oxides have become the cathode of choice for state–of–the–art Li–ion batteries, substantial gaps remain between the practical and theoretical energy densities. With the aim of supporting efforts to close this gap, this work reviews the fundamental operating mechanisms and challenges of Li intercalation in layered oxides, contrasts how these challenges play out differently for different materials (with emphasis on Ni–Co–Al (NCA) and Ni–Mn–Co (NMC) alloys), and summarizes the extensive corpus of modifications and extensions to the layered lithium oxides. Particular emphasis is given to the fundamental mechanisms behind the operation and degradation of layered intercalation electrode materials as well as novel modifications and extensions, including Na–ion and cation–disordered materials.

25 ENERGY STORAGE↗

Hollow nanoparticle cathode materials for sodium electrochemical cells and batteries

A cathode comprises, in its discharged state, a layer of hollow .gamma.-Fe.sub.2O.sub.3 nanoparticles disposed between two layers of carbon nanotubes, and preferably including a metallic current collector in contact with one of the layers of carbon nanotubes. Individual particles of the hollow .gamma.-Fe.sub.2O.sub.3 nanoparticles comprise a crystalline shell of .gamma.-Fe.sub.2O.sub.3 including cation vacancies within the crystal structure of the shell (i.e., iron vacancies of anywhere between 3% to 90%, and preferably 44 to 77% of available octahedral iron sites). Sodium ions are intercalated within at least some of the cation vacancies within the crystalline shell of the hollow .gamma.-Fe.sub.2O.sub.3 nanoparticles.

25 ENERGY STORAGE↗

Defect Chemistry in High‐Voltage Cathode Materials for Lithium‐Ion Batteries

High-voltage cathodes (HVCs) have emerged as a paramount role for the next-generation high-energy-density lithium-ion batteries (LIBs). However, the pursuit of HVCs comes with inherent challenges related to defective structures, which significantly impact the electrochemical performance of LIBs. The current obstacle lies in the lack of a comprehensive understanding of defects and their precise effects. This perspective aims to provide insights into defect chemistry for governing HVCs. The classifications, formation mechanisms, and evolution of defects are outlined to explore the intricate relationship between defects and electrochemical behavior. The pressing need for cutting-edge characterization techniques that comprehensively investigate defects across various temporal and spatial scales is emphasized. Building on these fundamental understandings, engineering strategies such as composition tailoring, morphology design, interface modification, and structural control to mitigate or utilize defects are thoroughly discussed for enhanced HVCs performance. Furthermore, these insights are expected to provide vital guidelines for developing high-performance HVCs for next-generation high-energy lithium-ion batteries.

cross-scale characterization↗

Construction of hierarchical porous NiCo{sub 2}O{sub 4} films composed of nanowalls as cathode materials for high-performance supercapacitor

Graphical abstract: Hydrothermal-synthesized NiCo{sub 2}O{sub 4} mesowall films exhibit porous structure and high capacity as well as good cycling life for supercapacitor application. - Highlights: • Hierarchical porous NiCo{sub 2}O{sub 4} nanowall films are prepared by a hydrothermal method. • NiCo{sub 2}O{sub 4} nanowall films show excellent electrochemical performance. • Hierarchical porous film structure is favorable for fast ion/electron transfer. - Abstract: Hierarchical porous NiCo{sub 2}O{sub 4} films composed of nanowalls on nickel foam are synthesized via a facile hydrothermal method. Besides the mesoporous walls, the NiCo{sub 2}O{sub 4} nanowalls are interconnected with each other to form hierarchical porous structure. These unique porous structured films possess a high specific surface area. The supercapacitor performance of the hierarchical porous NiCo{sub 2}O{sub 4} film is fully characterized. A high capacity of 130 mA h g{sup −1} is achieved at 2 A g{sup −1} with 97% capacity maintained after 2,000 cycles. Importantly, 75.6% of capacity is retained when the current density changes from 3 A g{sup −1} to 36 A g{sup −1}. The superior electrochemical performance is mainly due to the unique hierarchical porous structure with large surface area as well as shorter diffusion length for ion and charge transport.

36 MATERIALS SCIENCE↗