Results for “capability development” — Page 21

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRS1997

Developing Nationally Competitive NASA Research Capability in West Virginia

In May, 1995 West Virginia EPSCOR was awarded $150,000 to support activities to develop research capabilities in West Virginia in support of the National Aeronautics and Space Administration (NASA). These funds were used to support three projects: 1) Information Processing and the Earth Observing System, directed by Dr. Stuart Tewksbury of West Virginia University; 2) Development of Optical Materials for Atmospheric Sensing Experiments, directed by Dr. Nancy Giles of West Virginia University; and 3) Development of Doppler Global Velocimeter (DGV) for Aeronautical and Combustion Studies, directed by Dr. John Kuhlman of West Virginia University. The funding provides the means to develop capability in each of these areas. This report summarizes the technical accomplishments in each project supported under this award.

Calzonetti, Frank J.↗

NASA NTRS1995

Nascom System Development Plan: System Description, Capabilities and Plans

The NASA Communications (Nascom) System Development Plan (NSDP), reissued annually, describes the organization of Nascom, how it obtains communication services, its current systems, its relationship with other NASA centers and International Partner Agencies, some major spaceflight projects which generate significant operational communication support requirements, and major Nascom projects in various stages of development or implementation.

Source record↗

NASA NTRS2022

Development of Gas Analysis Capabilities

Project Description: The project objective was to develop gas analysis methodology and processes to identify and quantify contaminants specific to KSC, primarily volatile organic compounds (VOCs), utilizing the recently purchased gas chromatograph-mass spectrometer (GCMS) coupled with a sample pre-concentrator. This work established a standing, quick-turnaround quantitative GCMS methodology for KSC-specific VOCs associated with launching and landing spacecraft at trace-levels far below previous detection limits. Closeout Summary: This project established a standing methodology for rapid turnaround identification and quantification of 119 targeted VOCs considered most likely to be encountered at KSC. Of these, 111 of the calibration files are based on manufacturer-certified gas standard mixes. The other eight were generated using standards generated in-house from neat, certified reference materials using procedures for standard generation that were developed under this project. Additionally, the spectral signatures of two hydrofluorocarbon precision cleaning solvents, that are widely used in flight hardware processing, have been added to the mass spectral library for rapid qualitative identification.

Cristina Oropeza↗

NASA NTRS1983

Center of Excellence for Applied Mathematical and Statistical Research in support of development of multicrop production monitoring capability

Efforts in support of the development of multicrop production monitoring capability are reported. In particular, segment level proportion estimation techniques based upon a mixture model were investigated. Efforts have dealt primarily with evaluation of current techniques and development of alternative ones. A comparison of techniques is provided on both simulated and LANDSAT data along with an analysis of the quality of profile variables obtained from LANDSAT data.

Woodward, W. A.↗

NASA NTRS1980

Three-dimensional perspective software for representation of digital imagery data

A generalized three dimensional perspective software capability was developed within the framework of a low cost computer oriented geographically based information system using the Earth Resources Laboratory Applications Software (ELAS) operating subsystem. This perspective software capability, developed primarily to support data display requirements at the NASA/NSTL Earth Resources Laboratory, provides a means of displaying three dimensional feature space object data in two dimensional picture plane coordinates and makes it possible to overlay different types of information on perspective drawings to better understand the relationship of physical features. An example topographic data base is constructed and is used as the basic input to the plotting module. Examples are shown which illustrate oblique viewing angles that convey spatial concepts and relationships represented by the topographic data planes.

Junkin, B. G.↗

NASA NTRS1969

Automatic frequency discriminators and control for a phase-lock loop providing frequency preset capabilities Patent

Development of automatic frequency discriminators and control for phase lock loop providing frequency preset capabilities

Kline, A. J., Jr.↗

NASA NTRS1994

NASCOM system development plan: System description, capabilities, and plans, FY 94-2

The Nascom System Development Plan (NSDP) for FY 94-2 contains 17 sections. It is a management document containing the approved plan for maintaining the Nascom Network System. Topics covered include an overview of Nascom systems and services, major ground communication support systems, low-speed data system, voice system, high-speed data system, Nascom support for NASA networks, Nascom planning for NASA missions, and network upgrade and advanced systems developments and plans.

Source record↗

NASA NTRSDate not supplied

cFS Test Framework (CTF)

NASA's Core Flight System (cFS) provides a generic flight software framework architecture for developing flight software. As the cFS framework has gained popularity over the years within the flight software community, supporting software tools have been developed to assist in the design, development, testing and verification of flight software. The cFS Test Framework (CTF) is a recently developed cFS tool with capabilities to develop and run automated test and verification scripts against flight software targets. The CTF tool parses and executes JSON-based test scripts containing test instructions, while logging and reporting the results. CTF utilizes a plugin-based architecture to allow developers to extend CTF with new test instructions, external interfaces, and custom functionality. To interface with flight software, CTF parses a set of CCSDS message definition files to create the necessary command and telemetry structures for use during the test run. Additionally, CTF also supports interfacing with multiple cFS instances, allowing a test script to verify requirements that involve multiple flight software targets. Lastly, CTF provides support for executing test scripts against FSW running on remote or embedded hardware. This allows CTF to execute the same test scripts across different target configurations throughout the development process. In this presentation, we will introduce the cFS Test Framework (CTF) architecture, discuss the history of cFS testing frameworks, and present the features and capabilities currently provided by CTF. Lastly, we will show a demo of the CTF tool being used to execute test scripts against flight software.

Aly I Shehata↗

NASA NTRSDate not supplied

CFS Test Framework

NASA's Core Flight System (cFS) provides a generic flight software framework architecture for developing flight software. As the cFS framework has gained popularity over the years within the flight software community, supporting software tools have been developed to assist in the design, development, testing and verification of flight software. The cFS Test Framework (CTF) is a recently developed cFS tool with capabilities to develop and run automated test and verification scripts against flight software targets. The CTF tool parses and executes JSON-based test scripts containing test instructions, while logging and reporting the results. CTF utilizes a plugin-based architecture to allow developers to extend CTF with new test instructions, external interfaces, and custom functionality. To interface with flight software, CTF parses a set of CCSDS message definition files to create the necessary command and telemetry structures for use during the test run. Additionally, CTF also supports interfacing with multiple cFS instances, allowing a test script to verify requirements that involve multiple flight software targets. Lastly, CTF provides support for executing test scripts against FSW running on remote or embedded hardware. This allows CTF to execute the same test scripts across different target configurations throughout the development process. In this presentation, we will introduce the cFS Test Framework (CTF) architecture, discuss the history of cFS testing frameworks, and present the features and capabilities currently provided by CTF. Lastly, we will show a demo of the CTF tool being used to execute test scripts against flight software.

cfs↗

NASA NTRSDate not supplied

TPS to Enable a Uranus Orbiter Probe

Recent mission studies point to delivery of the probe either at Uranus or at Neptune will require 3-D Woven TPS, either the two layer HEEET or the single layer 3MDCP. Recent studies point to 3MDCP being more mass efficient. The 3MDCP capability being developed to support MSR EES is sufficient if the probe size is 1.25 m or less. If the prove diameter is larger than 1.25 m, a possibility then Dual layer HEEET which is scalable is at TRL 6 is certified and ready. It is possible to develop a seam approach that would allow 3MDCP and the mass savings could warrant development of a seam capability. Depending on the outcome of the planned Flagship mission study that Ames plans to support, Ames is already working on a concept that can be developed and demonstrated in the coming years. If in case Aerocapture is demonstrated through a Earth Flight Test and becomes part of the mission design for Uranus, this makes delivery of the probes from orbit easier. Whether the probe is to delivered from Orbit or not, still 3-D Woven (HEEET or 3MDCP) is the only TPS qualified to enable the Ice Giant in situ probes.

Matthew J Gasch↗

NASA NTRS2020

Distributed Spacecraft Autonomy (DSA): Development of Swarm Autonomy Capability and Scalability for Spacecraft

The Distributed Spacecraft Autonomy project is developing a suite of software tools that enable an operator to command and receive data from a swarm as a single entity, enable a swarm to autonomously coordinate its actions via distributed decision making and reactive closed-loop control, and model swarm behavior in the presence of anomalies or failures. Our use case is the mapping of the electron density of the ionosphere using radio tomography by coordinating the selection of appropriate GPS channels, and by recording Total Electron Count (TEC)measurements. DSA will be demonstrated on board the NASA Ames Starling mission a swarm of four small, LEO spacecraft, scheduled to launch in 2021. We will also perform a ground demonstration with simulated and hardware-in-the-loop elements, to validate the tools for controlling swarms of up to 100 assets.The capability to communicate autonomously between the swarm satellites is demonstrated via a sophisticated simulation architecture. Historical Plasma sphere TEC data obtained via dual-band Novatel GPS Receivers are utilized as a representative input data set for the swarm. The representative TEC data and GPS satellite observability information is fed to the autonomous software package in place of a true real-time ground data collection process. The swarm satellites actively share status updates amongst one another and utilize multi-agent decision making to optimally identify regions of interest in the TEC distribution. The software,aware of the bandwidth limitations of the swarm satellites, prioritizes explorative measurements,which define the range of observability for the satellites, as well as exploitative measurements,which focus on maximizing the observance potential of regions with prolonged, elevated TEC density. The science of this study can ultimately be used to determine the dynamics and coupling of Earth's magnetosphere, ionosphere, and atmosphere and their response to solar and terrestrial inputs. The findings can be applied to the imaging of critical, transient phenomena in the magnetosphere in later missions. Meanwhile, the swarm autonomy capabilities have far reaching potential in future satellite missions.As an experimental demonstration of the autonomous capabilities of the network, a message is first printed within a core Flight Executive (cFE) application. Two cFE applications that communicate with one another within the same core Flight System (cFS) are shown.Communication between mission applications on the internal cFE bus is extended to utilize Data Distribution Service (DDS) for vehicle-to-vehicle networking. The DDS middle ware provides reliable delivery, routing, and topic subscription features over User Data gram Protocol (UDP).Leveraging Linux containerization, a networked set of satellite instances are generated by script to simulate swarm behavior. Swarm commanding and synchronization through the network is demonstrated under various topologies and data-loss conditions. Finally, autonomous swarms calability from 2 satellites to 100 satellites is shown.

Fugate, Jason↗

NASA NTRSDate not supplied

Distributed Spacecraft Autonomy - Development of Swarm Autonomy Capability and Scalability for Spacecraft

The Distributed Spacecraft Autonomy project is developing a suite of software tools that enable an operator to command and receive data from a swarm as a single entity, enable a swarm to autonomously coordinate its actions via distributed decision making and reactive closed-loop control, and model swarm behavior in the presence of anomalies or failures. Our use case is the mapping of the electron density of the ionosphere using radio tomography by coordinating the selection of appropriate GPS channels, and by recording Total Electron Count (TEC) measurements. DSA will be demonstrated onboard the NASA Ames Starling mission – a swarm of four small, LEO spacecraft, scheduled to launch in 2021. We will also perform a ground demonstration with simulated and hardware-in-the-loop elements, to validate the tools for controlling swarms of up to 100 assets. The capability to communicate autonomously between the swarm satellites is demonstrated via a sophisticated simulation architecture. Historical Plasmasphere TEC data obtained via dual-band Novatel GPS Receivers are utilized as a representative input dataset for the swarm. The representative TEC data and GPS satellite observability information is fed to the autonomous software package in place of a true real-time ground data collection process. The swarm satellites actively share status updates amongst one another and utilize multi-agent decision making to optimally identify regions of interest in the TEC distribution. The software, aware of the bandwidth limitations of the swarm satellites, prioritizes explorative measurements, which define the range of observability for the satellites, as well as exploitative measurements, which focus on maximizing the observance potential of regions with prolonged, elevated TEC density. The science of this study can ultimately be used to determine the dynamics and coupling of Earth’s magnetosphere, ionosphere, and atmosphere and their response to solar and terrestrial inputs. The findings can be applied to the imaging of critical, transient phenomena in the magnetosphere in later missions. Meanwhile, the swarm autonomy capabilities have far reaching potential in future satellite missions. As an experimental demonstration of the autonomous capabilities of the network, a message is first printed within a core Flight Executive (cFE) application. Two cFE applications that communicate with one another within the same core Flight System (cFS) are shown. Communication between mission applications on the internal cFE bus is extended to utilize Data Distribution Service (DDS) for vehicle-to-vehicle networking. The DDS middleware provides reliable delivery, routing, and topic subscription features over User Datagram Protocol (UDP). Leveraging Linux containerization, a networked set of satellite instances are generated by script to simulate swarm behavior. Swarm commanding and synchronization through the network is demonstrated under various topologies and data-loss conditions. Finally, autonomous swarm scalability from 2 satellites to 100 satellites is shown.

Distributed Autonomy↗

NASA NTRS2022

In-space Servicing, Assembly, and Manufacturing (ISAM) State of Play 2022 Edition

The future of spaceflight will yield increasingly more ambitious missions to support civil, national security, and commercial space sectors. Achieving these ambitious missions is not feasible using the traditional paradigm of launching an integrated, fully functioning system on a single launch vehicle. For example, science and human exploration missions will desire payloads that are larger than any foreseeable launch vehicle fairing, national security missions will require persistent assets that are mobile and resilient, and commercial space missions will require cost-effective ways to update to the latest technology on orbit. In-space Servicing, Assembly, and Manufacturing (ISAM) can vastly expand the performance, availability, and lifetime of space systems compared to the traditional paradigm of launching an asset with no intent to ever touch it again. ISAM capabilities foster an ecosystem that changes the space operations paradigm, creating the foundation for sustainable exploration and serving as a multiplier for other capabilities like space logistics, power generation, and reusability. Previous achievements in ISAM have enabled ambitious human and robotic space missions. NASA’s International Space Station (ISS) operations and maintenance, servicing missions of the Hubble Space Telescope (HST), and Northrop Grumman’s Mission Extension Vehicle (MEV) demonstrate the dramatic operational missions that can be achieved using ISAM capabilities. Many current and upcoming flight demonstrations are advancing areas that will enable the next generation of civil, national security, and commercial space missions. This document describes the current state of ISAM missions, capabilities, and developments. Compiling and organizing the available ISAM capabilities will help mission designers incorporate ISAM technologies into their concepts, create the starting point for technology development plans and roadmaps, and provide technologists a survey of the field they are developing. This document divides the ISAM capabilities into 11 capability areas that describe the functions or activities that would be performed in space using ISAM. This version of the ISAM State of Play is part of a continuing journey to encourage the use of ISAM capabilities in space. Compiling and organizing the current state of ISAM provides a simple resource for those working in the ISAM ecosystem to ensure that the advancements being made build upon the investments of the past. The state of play is ever changing as new capabilities are developed, and this document will be periodically updated to ensure that it is relevant to those who need it in the future.

ISAM↗

NASA NTRS2015

Upper Stage Engine Composite Nozzle Extensions

Carbon-carbon (C-C) composite nozzle extensions are of interest for use on a variety of launch vehicle upper stage engines and in-space propulsion systems. The C-C nozzle extension technology and test capabilities being developed are intended to support National Aeronautics and Space Administration (NASA) and United States Air Force (USAF) requirements, as well as broader industry needs. Recent and on-going efforts at the Marshall Space Flight Center (MSFC) are aimed at both (a) further developing the technology and databases for nozzle extensions fabricated from specific CC materials, and (b) developing and demonstrating low-cost capabilities for testing composite nozzle extensions. At present, materials development work is concentrating on developing a database for lyocell-based C-C that can be used for upper stage engine nozzle extension design, modeling, and analysis efforts. Lyocell-based C-C behaves in a manner similar to rayon-based CC, but does not have the environmental issues associated with the use of rayon. Future work will also further investigate technology and database gaps and needs for more-established polyacrylonitrile- (PAN-) based C-C's. As a low-cost means of being able to rapidly test and screen nozzle extension materials and structures, MSFC has recently established and demonstrated a test rig at MSFC's Test Stand (TS) 115 for testing subscale nozzle extensions with 3.5-inch inside diameters at the attachment plane. Test durations of up to 120 seconds have been demonstrated using oxygen/hydrogen propellants. Other propellant combinations, including the use of hydrocarbon fuels, can be used if desired. Another test capability being developed will allow the testing of larger nozzle extensions (13.5- inch inside diameters at the attachment plane) in environments more similar to those of actual oxygen/hydrogen upper stage engines. Two C-C nozzle extensions (one lyocell-based, one PAN-based) have been fabricated for testing with the larger-scale facility.

Valentine, Peter G.↗

NASA NTRS2014

Development of a Microphone Phased Array Capability for the Langley 14- by 22-Foot Subsonic Tunnel

A new aeroacoustic measurement capability has been developed for use in open-jet testing in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22 tunnel). A suite of instruments has been developed to characterize noise source strengths, locations, and directivity for both semi-span and full-span test articles in the facility. The primary instrument of the suite is a fully traversable microphone phased array for identification of noise source locations and strengths on models. The array can be mounted in the ceiling or on either side of the facility test section to accommodate various test article configurations. Complementing the phased array is an ensemble of streamwise traversing microphones that can be placed around the test section at defined locations to conduct noise source directivity studies along both flyover and sideline axes. A customized data acquisition system has been developed for the instrumentation suite that allows for command and control of all aspects of the array and microphone hardware, and is coupled with a comprehensive data reduction system to generate information in near real time. This information includes such items as time histories and spectral data for individual microphones and groups of microphones, contour presentations of noise source locations and strengths, and hemispherical directivity data. The data acquisition system integrates with the 14x22 tunnel data system to allow real time capture of facility parameters during acquisition of microphone data. The design of the phased array system has been vetted via a theoretical performance analysis based on conventional monopole beamforming and DAMAS deconvolution. The performance analysis provides the ability to compute figures of merit for the array as well as characterize factors such as beamwidths, sidelobe levels, and source discrimination for the types of noise sources anticipated in the 14x22 tunnel. The full paper will summarize in detail the design of the instrumentation suite, the construction of the hardware system, and the results of the performance analysis. Although the instrumentation suite is designed to characterize noise for a variety of test articles in the 14x22 tunnel, this paper will concentrate on description of the instruments for two specific test campaigns in the facility, namely a full-span NASA Hybrid Wing Body (HWB) model entry and a semi-span Gulfstream aircraft model entry, tested in the facility in the winter of 2012 and spring of 2013, respectively.

Humphreys, William M.↗

NASA NTRSDate not supplied

Progressive Development of Fleet Management Capabilities for a High Density Vertiplex Environment

The High Density Vertiplex (HDV) Sub-Project, as part of NASA’s Advanced Air Mobility (AAM) Project, has been developing a reference automation architecture with a far-term view of scalable, high-density operations in and around vertiport terminal areas. One of the components of that architecture under development has been focused on fleet management capabilities to support the management of multiple AAM operations from a supervisory role of a fleet manager. This capability relies on connectivity and information exchanges with other services for airspace and vertiport management as well as with flight crews responsible for operation execution. This paper will present this capability with a focus on its user interface developments as well as its integration into the simulation and flight testing performed as part of the HDV research roadmap.

AAM↗