Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “backing layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Low-frequency noise in MoSe{sub 2} field effect transistors

One of the important performance metrics of emerging nanoelectronic devices, including low dimensional Field Effect Transistors (FETs), is the magnitude of the low-frequency noise. Atomically thin 2D semiconductor channel materials such as MoX{sub 2} (X ≡ S, Se) have shown promising transistor characteristics such as I{sub ON}/I{sub OFF} ratio exceeding 10{sup 6} and low I{sub OFF}, making them attractive as channel materials for next generation nanoelectronic devices. However, MoS{sub 2} FETs demonstrated to date exhibit high noise levels under ambient conditions. In this letter, we report at least two orders of magnitude smaller values of Hooge parameter in a back-gated MoSe{sub 2} FET (10 atomic layers) with nickel S/D contacts and measured at atmospheric pressure and temperature. The channel dominated regime of noise was extracted from the total noise spectrum and is shown to follow a mobility fluctuation model with 1/f dependence. The low noise in MoSe{sub 2} FETs is comparable to other 1D nanoelectronic devices such as carbon nanotube FETs (CNT-FETs) and paves the way for use in future applications in precision sensing and communications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

PROPAGATING WAVE PHENOMENA DETECTED IN OBSERVATIONS AND SIMULATIONS OF THE LOWER SOLAR ATMOSPHERE

We present high-cadence observations and simulations of the solar photosphere, obtained using the Rapid Oscillations in the Solar Atmosphere imaging system and the MuRAM magnetohydrodynamic (MHD) code, respectively. Each data set demonstrates a wealth of magnetoacoustic oscillatory behavior, visible as periodic intensity fluctuations with periods in the range 110-600 s. Almost no propagating waves with periods less than 140 s and 110 s are detected in the observational and simulated data sets, respectively. High concentrations of power are found in highly magnetized regions, such as magnetic bright points and intergranular lanes. Radiative diagnostics of the photospheric simulations replicate our observational results, confirming that the current breed of MHD simulations are able to accurately represent the lower solar atmosphere. All observed oscillations are generated as a result of naturally occurring magnetoconvective processes, with no specific input driver present. Using contribution functions extracted from our numerical simulations, we estimate minimum G-band and 4170 A continuum formation heights of 100 km and 25 km, respectively. Detected magnetoacoustic oscillations exhibit a dominant phase delay of -8 Degree-Sign between the G-band and 4170 A continuum observations, suggesting the presence of upwardly propagating waves. More than 73% of MBPs (73% from observations and 96% from simulations) display upwardly propagating wave phenomena, suggesting the abundant nature of oscillatory behavior detected higher in the solar atmosphere may be traced back to magnetoconvective processes occurring in the upper layers of the Sun's convection zone.

79 ASTRONOMY AND ASTROPHYSICS↗

The Effects of Sputtering Target Preparation and Deposition Temperature on ZnTe:Cu Film Properties

A back contact containing a sputtered ZnTe:Cu interface layer can produce high-performing thin-film CdS/CdTe photovoltaic devices. We have found that varying the ZnTe:Cu sputtering target fabrication processes and deposition temperature can affect material properties of the ZnTe:Cu films and the resulting device performance. Two different target 'recipes' with various copper contents were used to study changes in the compositional, structural, optical, and electrical properties of ZnTe:Cu films. Substrate temperature during deposition was also varied to investigate the temperature dependence of the films. It was found that the target recipe, Cu concentration in the target, and deposition temperature affect the composition of the ZnTe:Cu films, which impacts their structural, optical, and electrical properties.

14 SOLAR ENERGY↗

Programming correlated magnetic states with gate-controlled moiré geometry

The ability to control the underlying lattice geometry of a system may enable transitions between emergent quantum ground states. We report in situ gate switching between honeycomb and triangular lattice geometries of an electron many-body Hamiltonian in rhombohedral (R)–stacked molybdenum ditelluride (MoTe 2 ) moiré bilayers, resulting in switchable magnetic exchange interactions. At zero electric field, we observed a correlated ferromagnetic insulator near one hole per moiré unit cell with a widely tunable Curie temperature up to 14 K. Applying an electric field switched the system into a half-filled triangular lattice with antiferromagnetic interactions; further doping this layer-polarized superlattice tuned the antiferromagnetic exchange interaction back to ferromagnetic. Our work demonstrates R-stacked MoTe 2 moirés to be a laboratory for engineering correlated states with nontrivial topology.

Science & Technology - Other Topics↗

Hybrid dielectric light trapping designs for thin-film CdZnTe/Si tandem cells

Tandem solar cells consisting of high bandgap cadmium telluride alloys atop crystalline silicon have potential for high efficiencies exceeding the Shockley-Queisser limit. However, experimental results have fallen well below this goal significantly because of non-ideal current matching and light trapping. In this work, we simulate cadmium zinc telluride (CZT) and crystalline silicon (c-Si) tandems as an exemplary system to show the role that a hybrid light trapping and bandgap engineering approach can play in improving performance and lowering materials costs for tandem solar cells incorporating crystalline silicon. This work consists of two steps. First, we optimize absorption in the crystalline silicon layer with front pyramidal texturing and asymmetric dielectric back gratings, which results in 121% absorption enhancement from a planar structure. Then, using this pre-optimized light trapping scheme, we model the dispersion of the Cd x Zn 1-x Te alloys, and then adjust the bandgap to realize the best current matching for a range of CZT thicknesses. Using experimental parameters, the corresponding maximum efficiency is predicted to be 16.08 % for a total tandem cell thickness of only 2.2 μm.

14 SOLAR ENERGY↗

High efficiency (> 20%) heterojunction solar cell on 30μm thin crystalline Si substrates using a novel exfoliation technology

To achieve grid parity, photovoltaic (PV) technologies must reduce the production cost of PV modules to well below $0.50/Wp (peak Watt of power produced). In crystalline Si PV modules, which account for over 80% of all the PV modules in production worldwide, the cost of raw Si wafers is over 40% of the module cost. Therefore, there is an industry wide effort to reduce crystalline Si wafer thickness and improve efficiency. However, conventional wafer sawing technologies suffer from significant kerf losses and also are limited due to constraints on handling of free standing wafers that are thinner than 150μm. This project aims to develop low cost high efficiency crystalline Si solar cells using ultra thin (~ 30μm) layers of monocrystalline Silicon fabricated using a metal backed exfoliation technology. These exfoliated Si foils are backed by metal and rugged and flexible, which help in overcoming the yield losses and handling issues that are a problem for traditional thin Si wafers. The metal backing of the exfoliated foils poses new challenges in processing of such thin wafers and limits the temperature of processing to below 300C. The project develops further understanding of thin crystalline Si based cell architectures and potential processing issues involved in making high efficiency cells with metal backed monocrystalline Si foils. A 13.5% efficiency cell was demonstrated during this project and the individual components of surface passivation (Voc) and fill factor needed to obtain higher efficiency (16%) have also been shown. It is believed that with some changes to the cell manufacturing process and access to industrial quality passivation films, should enable high efficiency cells with this technology. The cost model indicates that with high efficiency cells in volume production, this technology can meet the Sunshot goals of < $0.50/Wp for PV module production. This project was run as a collaboration between AstroWatt, University of Texas, Austin, National Renewable Energy Laboratories, University of Florida, Gainesville and Georgia Institute of Technology with additional contributions from Institute for Energy Conversion, Delaware. The project has resulted in several conference publications and presentations during 2012.

14 SOLAR ENERGY↗

Prevention of cathode damage from positive ion bombardment

Mixed alkaline earth oxide compounds deposited into hole at cathode surface center prevent ion back bombardment damage to cathode by reducing oxide layer and by creating metallic diffusion along sides of hole for enhanced electron emission.

Bennett, W. H.↗

Wind-simulation tester for solar modules

Tester induces cyclic pressure loads across module surface, guaranteeing its mechanical integrity. Module to be tested is sandwiched between stiffened aluminum layers covered with rubber sheets. Automatic front and back pressure loading is cycled by pneumatic system on separate stand. Relief valves prevent overpressuring. Fixture operates at high speed, completing cycle in 5 seconds, and typically applies 2,400 pascals.

Griffith, J. S.↗

Viewing Integrated-Circuit Interconnections By SEM

Back-scattering of energetic electrons reveals hidden metal layers. Experiment shows that with suitable operating adjustments, scanning electron microscopy (SEM) used to look for defects in aluminum interconnections in integrated circuits. Enables monitoring, in situ, of changes in defects caused by changes in temperature. Gives truer picture of defects, as etching can change stress field of metal-and-passivation pattern, causing changes in defects.

Lawton, Russel A.↗

A Search of Large Amplitude Waves in Slow Shock in the Distant Tail and an Examination of Wave Turbulence in the Plasma Sheet Boundary Layer

Two fluid simulations predict that switch-off slow shocks should have large amplitude left-hand wave trains downstream of the shock. Recent simulations show that this feature depends on specific plasma parameters, such as Much number and ratio of electron-to-ion temperature. In this study we carefully examine all distant tail crossings using ISEE-3 field and plasma data. We seek large amplitude rotational waves and compare to shock parameters. We also investigate right-hand waves associated with ion beams in the plasma sheet boundary layer. We examine the role of those back-streaming ions from slow shocks in wave generation. Wave mode cascade and parametric decay in these regions also will be studied.

Ho, C. M.↗

Method for implementation of back-illuminated CMOS or CCD imagers

A method for implementation of back-illuminated CMOS or CCD imagers. An oxide layer buried between silicon wafer and device silicon is provided. The oxide layer forms a passivation layer in the imaging structure. A device layer and interlayer dielectric are formed, and the silicon wafer is removed to expose the oxide layer.

Pain, Bedabrata↗

Composite Bond Line Measurements Based on A Bayesian Analysis of Flash Thermography Data

For bonded composite materials, an accurate characterization of the adhesive bond line is needed to predict failure modes and fracture toughness. In this paper, bond line thickness was estimated from data obtained using through transmission flash thermography. The forward model that predicts back surface temperature is based on a three layer heat diffusion equation with varying diffusivity and flux boundary conditions. The corresponding inverse problem of estimating bond line thickness from measurement data was solved using a Bayesian approach that assumed Gaussian priors for the bond line thickness and thermal diffusivity of the adherends. Finally, the outputs of the thermography based method were compared to measurements that were collected using a micrometer and ultrasound testing.

Flash thermography↗

Composite Bond Line Measurements Based on a Bayesian Analysis of Flash Thermography Data

For bonded composite materials, an accurate characterization of the adhesive bond line is needed to predict failure modes and fracture toughness. In this paper, bond line thickness was estimated from data obtained using through transmission flash thermography. The forward model that predicts back surface temperature is based on a three layer heat diffusion equation with varying diffusivity and flux boundary conditions. The corresponding inverse problem of estimating bond line thickness from measurement data was solved using a Bayesian approach that assumed Gaussian priors for the bond line thickness and thermal diffusivity of the adherends. Finally, the outputs of the thermography based method were compared to measurements that were collected using a micrometer and ultrasound testing.

Flash thermography↗

Membrane electrode assembly and method of making the same

Disclosed herein is a method of manufacturing a membrane electrode assembly (MEA) including directly depositing a liquid suspension containing a platinum precursor onto an ionically conductive membrane (e.g., proton-exchange membrane) that, when the platinum precursor deposit layer is reduced, provides a layer that will scavenge hydrogen that has diffused back through the membrane due to cell stack pressure differential.

08 HYDROGEN↗

Enhancing secondary yield of a diamond amplifier using a nitrogen layer

A thin nitrogen-doped layer less than 4% of the total thickness in diamond thin film amplifier is shown to reduce losses of generated secondaries to the back contact, generated by a high energy primary electron beam compared to a thin film without the substitutional nitrogen layer modification. Simulation indicates that the losses due to absorption of diffusing electrons by the back contact may be considerably reduced by a factor of 2 (depending on field across the film, width of the nitrogen layer, and boron doping level), thereby mitigating undesirable effects associated with trace amounts of boron.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Photon and carrier management design for nonplanar thin-film copper indium gallium selenide photovoltaics

Nonplanar structured photovoltaic absorber design has potential to achieve high solar cell efficiency with significantly reduced material use. We report optoelectronic simulations that highlight photon and generated carrier management opportunities for improvement of thin film Cu(In x Ga 1-x )Se 2 (CIGS) device performance. Structures realized via either self-assembly or patterning via nanoimprint lithography, and also a combination of both are predicted to exhibit significant increases in short circuit current density and open circuit voltage simultaneously. The structures investigated include: 1) self-assembled nonplanar structures that strongly scatter incident light and enhance carrier generation near regions of high electric potential, 2) lithographicallypatterned embedded periodic dielectric structures, 3) planar dielectric layers that separate the CIGS absorber from the molybdenum back-contact via reduced-area contacts that minimize optical and electronic losses, 4) a combination of these for combined effects. We find that the self-assembled nonplanar CIGS cells with 700 nm planar equivalent thickness, combined with dielectric separation layers yield increases in short circuit current density and open circuit voltage up to 3.4 mA cm -2 and 29 mV, respectively. The absolute efficiency increases from 15.4% to 18.1%, compared to the predicted efficiency for planar CIGS thin film cells of equivalent thickness. The addition of a single layer MgF 2 anti-reflection coating brings the maximum predicted efficiency up to 19.7% for randomly textured devices.

14 SOLAR ENERGY↗

One-Dimensional Model for the Ultrasonic Response of Resin-Filled Gaps in Automated Tape Layup Composites

Automated tow placement has become a widely used fabrication technique, especially for large aerospace structures. Robotic heads lay down strips (tows) of preimpregnated fiber along programmed paths. The intention is to lay adjacent tows abutted to one another, but sometimes a gap is left between a tow and the previously-placed tow. If a tow gap exists, it fills with resin during cure, forming a fiber-free volume. In immersion ultrasonic pulse-echo measurements of a cured laminate, the gap can be observed to produce a noticeable echo, without significantly attenuating the back-wall reflection of the laminate. To understand this behavior, we considered a one dimensional model of the composite laminate, with a thin layer having the ultrasonic sound speed and density of neat resin, sandwiched between two layers of material having the sound speed and density of fiber-reinforced composite and surrounded on both sides by water. Neglecting attenuation, we considered the transmission and reflection coefficients of each interface, as well as that of the thin resin layer. Using the initial water/composite reflection as a reference, we computed the relative magnitude of the back surface/water reflection in the presence and in the absence of a resin-only layer, as well as the relative magnitude of the reflection arising from a thin resin layer in composite. While the one-dimensional model did not fully match the measurements, it did qualitatively explain the observed behavior.

Johnston, Patrick H.↗