Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “alloying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Characterization of Ternary NiTiPt High-Temperature Shape Memory Alloys

Pt additions substituted for Ni in NiTi alloys are known to increase the transformation temperature of the alloy but only at fairly high Pt levels. However, until now only ternary compositions with a very specific stoichiometry, Ni50-xPtxTi50, have been investigated and then only to very limited extent. In order to learn about this potential high-temperature shape memory alloy system, a series of over twenty alloys along and on either side of a line of constant stoichiometry between NiTi and TiPt were arc melted, homogenized, and characterized in terms of their microstructure, transformation temperatures, and hardness. The resulting microstructures were examined by scanning electron microscopy and the phase compositions quantified by energy dispersive spectroscopy."Stoichiometric" compositions along a line of constant stoichiometry between NiTi to TiPt were essentially single phase but by any deviations from a stoichiometry of (Ni,Pt)50Ti50 resulted in the presence of at least two different intermetallic phases, depending on the overall composition of the alloy. Essentially all alloys, whether single or two-phase, still under went a martensitic transformation. It was found that the transformation temperatures were depressed with initial Pt additions but at levels greater than 10 at.% the transformation temperature increased linearly with Pt content. Also, the transformation temperatures were relatively insensitive to alloy stoichiometry within the range of alloys examined. Finally, the dependence of hardness on Pt content for a series of Ni50-xPtxTi50 alloys showed solution softening at low Pt levels, while hardening was observed in ternary alloys containing more than about 10 at.% Pt. On either side of these "stoichiometric" compositions, hardness was also found to increase significantly.

Rios, Orlando↗
NASA NTRS1989

Elevated temperature aluminum alloys

Three aluminum-lithium alloys are provided for high performance aircraft structures and engines. All three alloys contain 3 wt % copper, 2 wt % lithium, 1 wt % magnesium, and 0.2 wt % zirconium. Alloy 1 has no further alloying elements. Alloy 2 has the addition of 1 wt % iron and 1 wt % nickel. Alloy 3 has the addition of 1.6 wt % chromium to the shared alloy composition of the three alloys. The balance of the three alloys, except for incidentql impurities, is aluminum. These alloys have low densities and improved strengths at temperatures up to 260.degree. C. for long periods of time.

Meschter, Peter↗
NASA NTRS2006

Development and Characterization of Improved NiTiPd High-Temperature Shape-Memory Alloys by Solid-Solution Strengthening and Thermomechanical Processing

The need for compact, solid-state actuation systems for use in the aerospace, automotive, and other transportation industries is currently motivating research in high-temperature shape-memory alloys (HTSMA) with transformation temperatures greater than 100 C. One of the basic high-temperature alloys investigated to fill this need is Ni(19.5)Ti(50.5)Pd30. Initial testing has indicated that this alloy, while having acceptable work characteristics, suffers from significant permanent deformation (or ratcheting) during thermal cycling under load. In an effort to overcome this deficiency, various solid-solution alloying and thermomechanical processing schemes were investigated. Solid-solution strengthening was achieved by substituting 5at% gold or platinum for palladium in Ni(19.5)Ti(50.5)Pd30, the so-called baseline alloy, to strengthen the martensite and austenite phases against slip processes and improve thermomechanical behavior. Tensile properties, work behavior, and dimensional stability during repeated thermal cycling under load for the ternary and quaternary alloys were compared. The relative difference in yield strength between the martensite and austenite phases and the dimensional stability of the alloy were improved by the quaternary additions, while work output was only minimally impacted. The three alloys were also thermomechanically processed by cycling repeatedly through the transformation range under a constant stress. This so-called training process dramatically improved the dimensional stability in these samples and also recovered the slight decrease in work output caused by quaternary alloying. An added benefit of the solid-solution strengthening was maintenance of enhanced dimensional stability of the trained material to higher temperatures compared to the baseline alloy, providing a greater measure of over-temperature capability.

Bigelow, Glen↗
NASA NTRS2011

Effects of Annealing Process on the Formability of Friction Stir Welded Al-Li Alloy 2195 Plates

Large rocket cryogenic tank domes have typically been fabricated using Al-Cu based alloys like Al-Cu alloy 2219. The use of aluminum-lithium based alloys for rocket fuel tank domes can reduce weight because aluminum-lithium alloys have lower density and higher strength than Al-Cu alloy 2219. However, Al-Li alloys have rarely been used to fabricate rocket fuel tank domes because of the inherent low formability characteristic that make them susceptible to cracking during the forming operations. The ability to form metal by stretch forming or spin forming without excessive thinning or necking depends on the strain hardening exponent "n". The stain hardening exponent is a measure of how rapidly a metal becomes stronger and harder. A high strain hardening exponent is beneficial to a material's ability to uniformly distribute the imposed strain. Marshall Space Flight Center has developed a novel annealing process that can achieve a work hardening exponent on the order of 0.27 to 0.29, which is approximately 50% higher than what is typically obtained for Al-Li alloys using the conventional method. The strain hardening exponent of the Al-Li alloy plates or blanks heat treated using the conventional method is typically on the order of 0.17 to 0.19. The effects of this novel annealing process on the formability of friction stir welded Al-Li alloy blanks are being studied at Marshall Space Flight Center. The formability ratings will be generated using the strain hardening exponent, strain rate sensitivity and forming range. The effects of forming temperature on the formability will also be studied. The objective of this work is to study the deformation behavior of the friction stir welded Al-Li alloy 2195 blank and determine the formability enhancement by the new annealing process.

Chen, Po-Shou↗
DOE OSTI2021

Design of heterogeneous structured Al alloys with wide processing window for laser-powder bed fusion additive manufacturing

Required microstructural attributes of an alloy vary with structural applications. The microstructural fine-tuning capability of laser-powder bed fusion (L-PBF) additive manufacturing (AM) enables application specific manufacture of the components. Such manufacture with L-PBF AM requires alloys that exhibit wide processing window and are amenable to multiple deformation mechanisms. However, high hot cracking susceptibility of Al alloys poses a barrier to such printability-performance synergy. In this work we show that an integration of, a) grain refinement through heterogeneous nucleation, and b) eutectic solidification, leads to crack-free parts at wide range of process parameters, microstructural heterogeneity, and hierarchy in the Al-Ni-Ti-Zr alloy. Such an integration targets hot cracking at multiple stages of solidification in L-PBF as opposed to the contemporary alloy design strategies that target hot-cracking at only specific stages of solidification. The Al-Ni-Ti-Zr alloy exhibits excellent printability and a high as-built tensile performance. Due to the wide processing window and amenability to multiple deformation mechanisms, the alloy microstructure and subsequently the performance, can be fine-tuned. Here, such strategy opens the gateway for application-specific manufacture of Al alloys with L-PBF AM and establishes a fundamental shift in current methodologies for design of these alloys for L-PBF AM.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structural stability of mechanically alloyed amorphous (FeCoNi) 70 Ti 10 B 20 under high-temperature and high-pressure

Nanostructured (FeCoNi) 70 Ti 10 B 20 (at%) alloy was synthesized by mechanical alloying from elemental powder mixture of Fe, Co, Ni, Ti and B using ball milling. The effect of ball milling time on the evolution of structure and morphology was investigated by X-ray diffraction, scanning and transmission electron microscopy and differential thermal analysis. It was observed that the formation of solid solution of (FeCoNi) 70 Ti 10 B 20 started from the very onset of the milling process. Crystallite size and lattice strains seemed to be leveled off after 20 h of milling with no further major changes. The milling process for longer periods introduced severe plastic deformations causing formation of amorphous phase of (FeCoNi) 70 Ti 10 B 20 . The amorphous alloy composition was confirmed by energy dispersive X-ray spectroscopy analysis that showed an excellent homogeneity of the alloying elements. The phase stability of the mechanically alloyed amorphous sample was further verified by employing high-temperature and high-pressure studies. The alloy samples heat-treated at 700 °C revealed crystallization of the amorphous phase. However, synchrotron-based high-pressure ambient temperature X-ray diffraction studies confirmed that the amorphous phase of the alloy remained stable up to the pressure of 30 GPa. Here, the 50 h milled sample after being annealed at 350 °C showed improvement in the soft magnetic properties of the alloy, which was due to the probable elimination of the residual stress in the amorphous phase of the alloy powders.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ordering effects on deformation substructures and strain hardening behavior of a CrCoNi based medium entropy alloy

Here, a CrCoNi based medium entropy alloy with small additions of Ti, Al and Nb (denoted as (CrCoNi) 93 Al 4 Ti 2 Nb) in the as-quenched condition, exhibits tensile properties comparable to those of the equiatomic CrCoNi alloy at room temperature. Dark field transmission electron microscopy (TEM), atomic resolution high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) together with atom probe tomography (APT) show that spatially-localized long range ordering (LRO) L1 2 domains exist in this alloy. The evolution of deformation substructure with plastic deformation in this alloy was characterized using electron backscatter diffraction (EBSD), electron channeling contrast imaging (ECCI) and STEM based techniques including the recently developed weak beam dark field STEM imaging. Plastic deformation occurs by the slip of a/2<110>dislocations, which are narrowly dissociated into Shockley partial dislocations on {111} slip planes. Their dissociation distances in the (CrCoNi) 93 Al 4 Ti 2 Nb alloy are much smaller than the widths of the corresponding partials in the equiatomic CrCoNi alloy due to one or more of the minor alloying elements (Al, Ti, Nb). Dislocation slip in this alloy has a pronounced planar character. The leading dislocations in slip bands glide as pairs due to the existence of LRO domains. Multipoles were formed through the slip of dislocations with opposite signs on adjacent {111} slip planes. Those multipoles serve as building blocks for the formation of subgrain structures consisting of fine slip bands. The distances between slip bands were continuously refined during plastic deformation and dynamic refinement of slip bands plays a crucial role in strain hardening. The effects of LRO domains on planar dislocation slip, the deactivation of deformation twinning and strain hardening of this alloy are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Glass formation during combinatorial sputtering in binary alloys

Glass formation is a complex phenomenon influenced by thermodynamic and kinetic aspects, which are often controlled by extrinsic contributions. While bulk metallic glasses are typically multicomponent alloys, binary alloys offer a simplified approach to studying glass formation. In this study, we fabricated 57 binary alloy systems through combinatorial sputtering, where each alloy system is represented in 66 different alloys. We developed an automated analysis to determine structure and composition using X-ray diffraction and energy-dispersive X-ray spectroscopy for over 3700 alloys. We found that ∼17 % of the alloys form glasses under the estimated cooling rate during sputtering of ∼10 8 K/s. Data analysis revealed that commonly used factors like atomic size ratio and heat of mixing are ineffective in predicting glass formation. However, the crystal structure mismatch of the alloys’ elements emerged as the strongest indicator of glass formation under sputtering conditions of binary alloys. Here, the differences in glass formation under slow cooling rates used for bulk glass formation and the here observed glass formation under rapid cooling rates are discussed.

Binary alloys↗
DOE OSTI2023

Additively manufactured Al-Ce-Ni-Mn alloy with improved elevated-temperature fatigue resistance

Here, the high cycle fatigue behavior of an additively manufactured (AM) Al-10.5Ce-3.1Ni-1.2Mn wt% alloy was evaluated at 350 °C. The measured fatigue strength of 50 MPa at this temperature is comparable to the most fatigue resistant wrought Al alloys (2618-T6 and 7079-T6) at 315 °C. Refinement of pore populations through advanced AM processing in the examined alloy led to oxide inclusions becoming dominant fatigue crack initiation sites. The distribution of microstructural features that determine crack initiation was measured by X-ray computed tomography and served as input to make fatigue strength model predictions with various methodologies. A Monte-Carlo based approach that was previously applied to predict the fatigue strength of cast aluminum alloys through pore size distributions yielded accurate predictions for the fatigue strength of this AM alloy. Given the tunability of defect distributions in AM alloys, the sensitivity of the Al-Ce-Ni-Mn alloy fatigue behavior to defect distributions and outstanding elevated-temperature fatigue resistance of this alloy; the results together suggest the possibility of a new generation of fatigue-resistant alloys produced by the additive manufacturing route.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase stability in cast and additively manufactured Al-rich Al-Cu-Ce alloys

Additively manufactured (AM) eutectic Al alloy systems have been studied extensively for advantageous thermal stability and mechanical properties due to their refined microstructures. Al-Cu-Ce alloys are one subset of these AM eutectic alloys. Here we studied phase stability in AM Al-Cu-Ce alloys and compared it to that of conventionally cast ones. A new phase, Al 8 Cu 3 Ce, was identified in the microstructures of both AM and cast Al-Cu-Ce alloys. This Al 8 Cu 3 Ce phase was not previously included on experimental or thermodynamically calculated phase diagrams of the Al-Cu-Ce system. Therefore, we performed additional thermodynamic modeling of the system. These models were experimentally validated with cast and subsequently heat-treated Al-Cu-Ce alloys. We found that despite the refined microstructure of the AM alloys, the phases formed were consistent with the cast alloys, suggesting that AM processing did not significantly alter the formation and stability of phases from that in the conventional alloys. In conclusion, this work has resolved inconsistent previous descriptions of the Al-Cu-Ce ternary phase diagram in the Al-rich region and resulted in the addition of the Al 8 Cu 3 Ce as an equilibrium phase above 500 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Evaluating the efficacy of aluminide coatings to improve oxidation resistance of high performance engine valve alloys

Increasing peak cylinder pressures and operating temperatures of turbo-charged internal combustion engines (ICEs) engines present new challenges for existing materials employed in engine exhaust valves. Oxidation induced degradation of current Ni based alloys for these components will be a life-limiting mechanism while strict cost margins in the automotive transportation industry further limit the choice of suitable candidate materials. Metallic diffusion aluminide coatings can provide a cost-effective way to improve the oxidation resistance of underlying materials. In this study, the high temperature oxidation behavior of diffusion nickel aluminide coatings on two Ni based alloys (commercially available alloy 31V and a developmental alloy) during cyclic oxidation behavior in air+10% H 2 O at 900 °C was investigated. A complete depletion of the beneficial Al-rich β-(NiFe)Al phase was observed in the coating on alloy 31V while a significant fraction of this phase was retained in the coating on the second alloy. A coupled thermodynamic-kinetic model showed that the disappearance of the Al-rich phase in the coating on 31V was mainly due to the combined effect of steeper chemical potential gradients of Al and Ti between the coating and the substrate and their faster diffusivities compared to the coated developmental alloy. Finally, a higher content of Fe was shown to support the retention of β-(NiFe)Al phase in the coating on the developmental alloy while the presence of Ti in the alloy was shown to be detrimental for long-term coating performance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Additively manufactured and cast high-temperature aluminum alloys for electric vehicle brake rotor application

Electric vehicle brake rotors demand lightweight, high thermal conductivity materials with good resistance to wear, creep, salt corrosion, and thermal fade, all of which present challenges to the traditionally used cast iron. In this work, we investigated the braking performance of recently developed high-temperature aluminum alloys in both cast and 3D printed forms, that possess excellent microstructural and mechanical stability at elevated temperatures. Three aluminum alloys, Al-6Cu-Mn-Zr, Al-9Cu-Mn-Zr, and Al-Ce-Ni-Mn-Zr and a reference cast iron were tested on a sub-scale brake tester against a commercial brake pad material over a range of sliding speeds between 2 and 15 m/s. The performance of these alloys was evaluated for wear resistance, friction behavior, temperature elevation, and surface morphological change. Although all three candidate alloys had lower wear-resistance than cast iron, Al-Ce-Ni-Mn-Zr showed a significantly reduced wear rate in comparison to the Al-Cu-Mn-Zr alloys. Moreover, Al-Ce-Ni-Mn-Zr alloy had the most consistent friction behavior at all sliding speeds and good fade resistance, as the coefficient of friction did not dramatically decrease with temperature rise but stayed within a desirable range of 0.35–0.50 instead. The superior wear resistance and braking performance of the Al-Ce-Ni-Mn-Zr alloy were attributed to its higher hardness, and high temperature yield strength and creep resistance compared with the Al-Cu-Mn-Zr alloys. In conclusion, the results suggest that the braking performance of these aluminum alloys could be further enhanced by increasing the hardness and forming a more stable transfer layer on the sliding surface.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Upward band gap bowing and negative mixing enthalpy in multi-component cubic halide perovskite alloys

Physical properties intermediate between constituents of alloys can be achieved as downward convex positive bowing, upward concave negative bowing, or zero bowing. Such bowing effects are essential for band gap engineering in semiconductor alloys. Upward band gap bowing effects are rather rare, hindering the exploration on half of the available physical property space of alloys. Part of this being a rare event is related to the need to stabilize an alloy with low mixing enthalpy, so it does not phase separate. Here, in this paper, we find via density functional theory that one can satisfy the simultaneous conditions of negative mixing enthalpy and upward band gap bowing in four-component AB⁢X 3 halide perovskite alloys in the cubic perovskite structure. Such perovskite alloys have the B-site occupied by a mixture of group IVB and IIB elements that have the IVB-𝑠 and IIB-s states in the valence bands and conduction bands, respectively, leaving the delocalized 𝑠 states to strongly repel each other. This 𝑠−𝑠 repulsion leads to the upward band gap bowing and negative mixing enthalpies simultaneously. Remarkably, we identify a perovskite alloy that has a band gap much larger than all its components. Analogous trends of upward band gap bowing and negative mixing enthalpy also appear in the corresponding three-component and two-component AB⁢X 3 halide perovskite alloys. These observations of upward band gap bowing and negative mixing enthalpy will significantly accelerate the design of stable upward band gap bowing alloys in a broad range of material families.

14 SOLAR ENERGY↗
DOE OSTI2023

Compositional Modifications to Alter and Suppress Laves Phases in Al x CrMoTa y Ti Alloys

The development of refractory complex concentrated alloys in the Al–Cr–Mo–Ta–Ti alloy system is reported. Alloys with modified Al and Ta concentrations are designed using CALPHAD tools and produced via arc melting and characterized in both as-cast and annealed forms. Properties of the alloys, nature of the microstructures, and phase transformation behavior are described via X-ray diffraction, microstructural characterization, microhardness, and differential scanning calorimetry. Two alloys, namely, Al 0.25 CrMoTa 0.8 Ti and Al 0.75 CrMoTa 0.8 Ti, are represented by a body-centered-cubic matrix phase after annealing, along with a secondary Cr–Ta Laves phase of the C15 and C14 polytypes, respectively. In as-cast and annealed forms, the Al 0.75 CrMoTa 0.45 Ti alloy comprises a single-bcc phase. Microhardness of the Laves phase containing alloys demonstrates susceptibility to cracking, whereas the Al 0.75 CrMoTa 0.45 Ti alloy displays high specific hardness, signs of ductility as evidenced by slip traces near indentations, and minimal scatter of hardness values.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Evaluation of Equiatomic CrMnFeCoNiCu System and Subsequent Derivation of a Non-Equiatomic MnFeCoNiCu Alloy

Investigation into non-equiatomic high-entropy alloys has grown in recent years due to questions about the role of entropy stabilization in forming single-phase solid solutions. Non-equiatomic alloys have been shown to retain the outstanding mechanical properties exhibited by their equiatomic counterparts and even improve electrical, thermal, and magnetic properties, albeit with relaxed composition bounds. However, much remains to understand the processing–structure–property relationships in all classes of so-called high-entropy alloys (HEAs). Here, we are motivated by the natural phenomena of crystal growth and equilibrium conditions to introduce a method of HEA development where controlled processing conditions determine the most probable and stable composition. This is demonstrated by cooling an equiatomic CrMnFeCoNiCu alloy from the melt steadily over 3 days (cooling rate ~4 °C/h). The result is an alloy containing large Cr-rich precipitates and an almost Cr-free matrix exhibiting compositions within the MnFeCoNiCu system (with trace amounts of Cr). From this juncture, it is argued that the most stable composition is within the CrMnFeCoNiCu system rather than the CrMnFeCoNi system. With further optimization and evaluation, a unique non-equiatomic alloy, Mn 17 Fe 21 Co 24 Ni 24 Cu 14 , is derived. The alloy solidifies and recrystallizes into a single-phase face-centered cubic (FCC) polycrystal. In addition to possible applications where Invar is currently utilized, this alloy can be used in fundamental studies that contrast its behavior with its equiatomic counterpart and shed light on the development of HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Characterization of Recrystallized Grains During Static Recrystallization of Hot-Compressed Mg–Zn–Ca Alloys Using In Situ Far-Field High-Energy Diffraction Microscopy

In this study, we explored the effect of Zn content on the static recrystallization of three 80 pct hot-compressed alloys, Mg–0.5Zn–0.1Ca wt pct (ZX050), Mg–1Zn–0.1Ca wt pct (ZX10), and Mg–3.2Zn–0.1Ca wt pct (ZX30), using far-field high-energy microscopy (ff-HEDM). Individual recrystallized grains were tracked and their 3D centroid, relative volume, and grain-averaged crystallographic orientation were measured during annealing. These measurements were used to compare the recrystallization kinetics and texture evolution of recrystallized grains in ZX alloys as a function of the Zn content. Fully recrystallized microstructures were observed for the ZX30 and the ZX10 alloys after annealing at 230 °C and 330 °C, respectively. In contrast, only a partially recrystallized microstructure for the ZX050 alloy was observed after > 1 hour of annealing at 430 °C. The resistance to recrystallization with decreasing Zn content was also confirmed by detecting faster growth rates of recrystallized grains in the ZX10 and ZX30 alloys, and slower growth rates in the ZX050 alloy. The significant recrystallization texture weakening of the ZX10 and ZX30 alloys and the development of a basal texture in the ZX05 alloy were described based on the orientation dependency of nucleation and growth of recrystallized grains. The analysis demonstrated that texture weakening was associated with increasing Zn content in Mg–Zn–Ca alloys.

Roumina, Reza [Univ. of Michigan, Ann Arbor, MI (U↗
DOE OSTI2021

Void swelling of conventional and composition engineered HT9 alloys after high-dose self-ion irradiation

Ferritic/martensitic (F/M) steels are being considered as potential structural materials for next generation nuclear reactors, and variants of the alloy HT9 are some of the most promising candidates. In this study, two conventional and two composition engineered HT9 alloys were irradiated using 3.5 MeV Fe 2+ up to 600 peak displacement-per-atom (dpa) at 450 °C. Void swelling and microstructure evolution were characterized for each alloy and compared. The two conventional HT9 alloys (INL and ACO3) showed similar void swelling behavior due to their similar elemental composition and processing conditions. The INL HT9 exhibited a maximum of 2.4% swelling and the ACO3 HT9 showed a maximum of 2.8% swelling at 342 and 393 average local dpa, respectively. On the other hand, the two-composition engineered HT9 alloys with varying N contents (10 ppm for low N and 440 ppm for high N) showed disparate swelling behavior. The low N HT9 exhibited a maximum of 4.6% swelling, while the high N HT9 showed a maximum of 0.7% swelling at 342 average local dpa. Changes in the N content also affected Ni/Si rich G-phase formation. The low N HT9 showed a larger size and lower density of G-phase precipitates compared with the high N HT9 after 600 peak dpa irradiation. This study compares the void swelling behavior of the ion irradiated four current HT9 alloys to extremely high doses, with the void swelling data from neutron irradiated HT9 alloys. Furthermore, the comparison lends critical insights into how well these current alloys can withstand high neutron fluxes in future reactors, especially since the low N and high N HT9 alloys have never been exposed to such high doses before.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Insights into radiation resistance of titanium alloys from displacement cascade simulations

Radiation damage in beam window materials limits the use of high power proton beams in high energy physics research. The alloy Ti-6Al-4V is presently used as a beam window material but a prospective alternative, Ti-15V-3Cr-3Sn-3Al has been proposed. Since both these alloys contain dual phases at room temperature, we compare the radiation damage in the α and ß-phases of these two materials via primary knock-on atom (PKA) cascade simulations in the 10-40keV energy range. At PKA energies 30 and 40keV, the number of Frenkel pairs in the ballistic stage is higher in the ß-phase of Ti-6Al-4V than that in the ß-phase of Ti-15V-3Cr-3Sn-3Al almost by a factor of 2. The α-phase, of both these alloys, by far outperforms the ß-phases of the two alloys, both in terms of damage during the ballistic stage and in terms of the surviving defects. The average displacement threshold energy (E d ) in the α-phase of both alloys was found to be 66eV while that in the ß-phase of Ti-15-3 was 55 eV and in the ß-phase of Ti-6-4 was 46. Further, while the number of surviving defects is almost equal in both alloys, the vacancy and interstitial clustering mechanisms differ notably, which can impact the degree of radiation hardening and loss of ductility. Our simulations show larger vacancy and interstitial clusters form in Ti-6Al-4V as compared to that in Ti-15-3-3-3 alloy. These results indicate that Ti-15-3-3-3 alloys may be a promising candidate for next generation beam window material with a higher radiation tolerance than the existing Ti-6-4 alloy.

36 MATERIALS SCIENCE↗