Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “adhesion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Adhesion in thermomechanically processed seaweed-lignocellulosic composite materials

The increasing concerns associated with petroleum-derived polymers motivate the development of sustainable, renewably sourced alternatives. In ubiquitous applications such as structural materials for infrastructure, the built environment as well as packaging, where natural materials such as wood are used, we rely on nonrenewable and nondegradable polymers to serve as adhesives. In wood panels, such as medium density fiberboards (MDFs), formaldehyde-based resins are predominantly used to bond wood fibers and to provide strength to the materials. To further mitigate the environmental impact of construction materials, more sustainable adhesives need to be investigated. Here, in this article, we introduce Ulva seaweed as an adhesive to enable cohesion and strength in hot-pressed wood panels. Upon hot-pressing, powdered Ulva flows in between the wood particles, generating a matrix, which provides strong binding. We show that the flexural strength of Ulva-bonded wood biocomposites increases with increasing Ulva concentrations. At an Ulva concentration of 40 wt%, our composites reach an average elastic modulus of 6.1 GPa, and flexural strength of 38.2 MPa (compared to 4.7 GPa and 22.6 MPa, respectively, for pure wood compressed at the same pressing conditions). To highlight the bonding mechanisms, we performed infrared and x-ray photoelectron spectroscopy and identified indications of fatty acid mobility during hot-pressing. In addition, we demonstrate that the presence of Ulva improves other properties of the composites such as water resistance and fame retardancy. Ulva is also shown to behave as an excellent adhesive agent between two prepressed beams. Finally, we perform an in-depth analysis of the environmental impact of wood-Ulva biocomposites.

36 MATERIALS SCIENCE↗

Potting Adhesion Investigation Using Double Cantilever Beam Tests

The adhesive properties of an elastomeric potting material were investigated experimentally using double cantilever beam (DCB) specimens. In these tests, the applied load and opening displacement were measured, with the goal of quantitatively characterizing the adhesive strength of the thin layer of potting material. The DCB tests were also simulated using a finite element model that incorporated an adhesive traction-separation model to represent the compliance of the potting layer and evolving (weakening) strength of the potting-to-metal adhesive interfaces. The test and simulation results were used to determine a range of traction-separation model parameters, expressed in the form of correlated probability distributions, that constitute a good calibration of the model over the range of variability exhibited in the test series.

36 MATERIALS SCIENCE↗

Anti-Adhesion Elastomer Seal Coatings for Ultraviolet and Atomic Oxygen Protection

Radiation blocking sunscreen coatings have been developed for the protection of elastomer seals used in low-Earth-orbit (LEO). The coatings protect the seals from ultraviolet (UV) radiation and atomic oxygen (AO) damage. The coatings were developed for use on NASA docking seals. Docking seal damage from the UV and AO present in LEO can constrain mission time-line, flight mode options, and increases risk. A low level of adhesion is also required for docking seals so undocking push-off forces can be low. The coatings presented also mitigate this unwanted adhesion. Greases with low collected volatile condensable materials (CVCM) and low total mass loss (TML) were mixed with slippery and/or UV blocking powders to create the protective coatings. Coatings were applied at rates up to 2 milligrams per square centimeter. Coated seals were exposed to AO and UV in the NUV (near-UV) and UV-C wavelength ranges (300 to 400 nanometers and 254 nanometers, respectively). Ground based ashers were used to simulate the AO of space. The Sun's UV energy was mimicked assuming a nose forward flight mode, resulting in an exposure rate of 2.5 megajoules per square meter per day. Exposures between 0 and 147 megajoules per square meter (UV-C) and 245 megajoules per square meter (NUV) were accomplished. The protective coatings were durable, providing protection from UV after a simulated docking and undocking cycle. The level of protection begins to decline at coverage rates less than 0.9 milligrams per square centimeter. The leakage of seals coated with Braycote plus 20 percent Z-cote ZnO sunscreen increased by a factor of 40 after moderate AO exposure; indicating that this coating might not be suitable due to AO intolerance. Seals coated with DC-7-16.4 percent Z-cote ZnO sunscreen were not significantly affected by combined doses of 2 x 10 (sup 21) atoms per square AO with 73 megajoules per square meter UV-C. Unprotected seals were significantly damaged at UV-C exposures of 0.3 megajoules per square meter and DC-7-16.4 percent Z-cote coated seals were undamaged at all exposures up to the limits tested thus far which were 147 megajoules per square meter UV-C and 245 megajoules per square meter NUV. The coatings decreased adhesion sufficiently for docking seals at temperatures equal to or greater than -8 degrees Centigrade thus offer a simple and inexpensive way to mitigate adhesion.

adhesion↗

Bio-inspired Surface Structures to Mitigate Interfacial Particle Adhesion and Erosion - A Review

Lunar dust known as regolith is a huge challenge for lunar exploration missions. Formed over millennia by a complex process involving impacts of meteoroids and micrometeoroids on the lunar surface, lunar dust is porous, highly abrasive with sharp jagged edges, chemically reactive, electrostatically charged and sometimes magnetic. The chemical composition and thickness of the dust layer also varies in different regions of the lunar surface. From samples obtained by previous lunar missions, the average particle size is below 100 microns. This dust has the tendency to strongly adhere to any exposed surfaces, and often degrades the material functionality to eventually cause failure. Any material on the lunar surface is also subject to harsh temperature cycles ranging from -178 ̊C to + 123 ̊C and extreme ultraviolet radiation. While on the lunar surface, different classes of materials would be required for different applications. Advanced materials have been and will be used throughout the lunar lander, habitat, and mission equipment. Examples include: polymeric materials for astronaut protective clothing; metals and ceramics for the lunar lander legs and habitats, and excavating equipment; and semiconductors for solar panels and on-board electronics. In all these applications, the surfaces of the materials are expected or understood to be exposed to the extreme lunar environment condition that includes the regolith dust. During the Apollo missions, the dust clung to and abraded the astronaut’s suits, degraded seals, optics, clogged sensors and reduced performance of thermal radiators. The lunar dust adheres to the surface by various mechanisms, which include electrostatic and Coulombic interactions, Van-der-Waals forces, magnetic forces, mechanical interlocking, chemical bonding and donor-acceptor interactions. There are three primary strategies for developing technologies to minimize the lunar dust adhesion: active, passive and a combination of active and passive. In the active approach, an external energy is needed to prevent or remove particles from collecting on the surface. Mechanically powered brushes and electrodynamic dust screens are two examples. In the passive approach, no external power is needed, and the material surface properties are able to mitigate dust adhesion. A well-known example of this strategy is the low work function coatings for non-stick surfaces. In most cases a combination of active and passive methods might be needed to optimally manage the lunar regolith. The passive method is significantly more attractive as it does not require any external power or an additional control subsystem. These approaches optimize the mission payload and reduce risk. Surface modification to minimize the dust adhesion is thus very important to lunar missions. Here, naturally evolved surface structures might provide guidance for solutions. There are several factors that have to be considered for minimizing particle adhesion to a surface. These include the substrate material properties, surface topography, chemistry, and the characteristics of the adhering particles. When engineering a surface, the substrate material chosen would be dependent on the needs of the application. Tailoring the surface microstructure or chemistry opens up more possibilities for its optimal utilization

Lunar Dust↗

Designed Adhesion - Exploring the Unknown

The ability to design materials and substrates for adhesive properties is highly desirable for the aeronautics industry. This includes the ability to design substrates that have low ice adhesion to increase efficiency of the fleet, as well as the ability to design structural adhesives to improve manufacturing rate. The Designed Adhesion group was chosen during the 2023 Wicked Wild Pitch Event sponsored by CAS and is currently in the discovery phase.

Design↗

Pre-photolithographic GaAs surface treatment for improved photoresist adhesion during wet chemical etching and improved wet etch profiles.

Results of several experiments aimed at remedying photoresist adhesion failure during spray wet chemical etching of InGaP/GaAs NPN HBTs are reported. Several factors were identified that could influence adhesion and a Design of Experiment (DOE) approach was used to study the effects and interactions of selected factors. The most significant adhesion improvement identified is the incorporation of a native oxide etch immediately prior to the photoresist coat. In addition to improving adhesion, this pre-coat treatment also alters the wet etch profile of (100) GaAs so that the reaction limited etch is more isotropic compared to wafers without surface treatment; the profiles have a positive taper in both the [011] and [011] directions, but the taper angles are not identical. The altered profiles have allowed us to predictably yield fully probe-able HBTs with 5 x 5 {micro}m emitters using 5200 {angstrom} evaporated metal without planarization.

36 MATERIALS SCIENCE↗

Damage prognosis of adhesively-bonded joints in laminated composite structural components of unmanned aerial vehicles

The extensive use of lightweight advanced composite materials in unmanned aerial vehicles (UAVs) drastically increases the sensitivity to both fatigue- and impact-induced damage of their critical structural components (e.g., wings and tail stabilizers) during service life. The spar-to-skin adhesive joints are considered one of the most fatigue sensitive subcomponents of a lightweight UAV composite wing with damage progressively evolving from the wing root. This paper presents a comprehensive probabilistic methodology for predicting the remaining service life of adhesively-bonded joints in laminated composite structural components of UAVs. Non-destructive evaluation techniques and Bayesian inference are used to (i) assess the current state of damage of the system and, (ii) update the probability distribution of the damage extent at various locations. A probabilistic model for future loads and a mechanics-based damage model are then used to stochastically propagate damage through the joint. Combined local (e.g., exceedance of a critical damage size) and global (e.g.. flutter instability) failure criteria are finally used to compute the probability of component failure at future times. The applicability and the partial validation of the proposed methodology are then briefly discussed by analyzing the debonding propagation, along a pre-defined adhesive interface, in a simply supported laminated composite beam with solid rectangular cross section, subjected to a concentrated load applied at mid-span. A specially developed Eliler-Bernoulli beam finite element with interlaminar slip along the damageable interface is used in combination with a cohesive zone model to study the fatigue-induced degradation in the adhesive material. The preliminary numerical results presented are promising for the future validation of the methodology.

42 ENGINEERING↗

Synthetic Butterfly Scale Surfaces with Compliance‐Tailored Anisotropic Drop Adhesion

Abstract Many natural surfaces such as butterfly wings, beetles' backs, and rice leaves exhibit anisotropic liquid adhesion; this is of fundamental interest and is important to applications including self‐cleaning surfaces, microfluidics, and phase change energy conversion. Researchers have sought to mimic the anisotropic adhesion of butterfly wings using rigid surface textures, though natural butterfly scales are sufficiently compliant to be deflected by capillary forces exerted by drops. Here, inspired by the flexible scales of the Morpho aega butterfly wing, synthetic surfaces coated with flexible carbon nanotube (CNT) microscales with anisotropic drop adhesion properties are fabricated. The curved CNT scales are fabricated by a strain‐engineered chemical vapor deposition technique, giving ≈5000 scales of ≈10 µm thickness in a 1 cm 2 area. Using various designed CNT scale arrays, it is demonstrated that the anisotropy of drop roll‐off angle is influenced by the geometry, compliance, and hydrophobicity of the scales; and a maximum roll‐off anisotropy of 6.2° is achieved. These findings are supported by a model that relates the adhesion anisotropy to the scale geometry, compliance, and wettability. The electrical conductivity and mechanical robustness of the CNTs, and the ability to fabricate complex multidirectional patterns, suggest further opportunities to create engineered synthetic scale surfaces.

Zhao, Hangbo↗

Dissimilar material joining of densified superwood to aluminum by adhesive bonding

Abstract Superwood is a densified wood product that shows promise as a lightweight and renewable alternative for metallic materials. In order for this high-performance new material to be used in multi-material products, it must be able to be joined with other major materials. For example, joining superwood to aluminum would provide a key enabling technology for its use in automotive components since aluminum is presently a major lightweight material for such applications. In this paper, a methacrylate-based adhesive has been identified to provide high lap shear strength (7.5 MPa) for aluminum-to-superwood joints. The aluminum-to-superwood samples were prepared with different amounts of pre-polishing to create openings to the pores in the superwood so adhesive could penetrate into them and create a mechanical interlock, in addition to the hydrogen/chemical bonding at the surface between the methyl methacrylate (MMA) in methacrylate-based adhesive and the cellulose in superwood. For aluminum samples, a thin layer (typically a few nanometers) of oxide film on the surfaces provides hydrogen/chemical bond to MMA structure in the adhesive layer. The failure strength of the superwood-to-aluminum joint sample is about 50% higher than that of natural wood to natural wood joint sample and comparable to that of aluminum-to-aluminum joint sample.

Automation & Control Systems↗

Improving Joint Formation and Tensile Properties of Dissimilar Friction Stir Welding of Aluminum and Magnesium Alloys by Solving the Pin Adhesion Problem

Friction stir welding (FSW), as a solid-state welding technology invented by TWI in 1991, has potential to join dissimilar Al/Mg alloys. In this study, the pin adhesion phenomenon affecting joint quality during FSW of 6061-T6 aluminum and AZ31B magnesium alloys was investigated. The adhesion phenomenon induced by higher heat input easily transformed the tapered-and-screwed pin into a tapered pin, which greatly reduced the tool’s ability to drive the plasticized materials and further deteriorated joint formation. Under the condition without the pin adhesion, the complex intercalated interlayer at the bottom of stir zone was beneficial to mechanical interlocking of Al/Mg alloys, improving tensile properties. However, the formation of intermetallic compounds was still the main reason of the joint fracture, significantly deteriorating tensile properties. Under the welding speed of 60 mm/min without the pin adhesion phenomenon, the maximum tensile strength of 107 MPa and elongation of 1.2% were achieved.

36 MATERIALS SCIENCE↗

PI3K{gamma} activation by CXCL12 regulates tumor cell adhesion and invasion

Tumor dissemination is a complex process, in which certain steps resemble those in leukocyte homing. Specific chemokine/chemokine receptor pairs have important roles in both processes. CXCL12/CXCR4 is the most commonly expressed chemokine/chemokine receptor pair in human cancers, in which it regulates cell adhesion, extravasation, metastatic colonization, angiogenesis, and proliferation. All of these processes require activation of signaling pathways that include G proteins, phosphatidylinositol-3 kinase (PI3K), JAK kinases, Rho GTPases, and focal adhesion-associated proteins. We analyzed these pathways in a human melanoma cell line in response to CXCL12 stimulation, and found that PI3K{gamma} regulates tumor cell adhesion through mechanisms different from those involved in cell invasion. Our data indicate that, following CXCR4 activation after CXCL12 binding, the invasion and adhesion processes are regulated differently by distinct downstream events in these signaling cascades.

60 APPLIED LIFE SCIENCES↗

RhoA GTPase regulates radiation-induced alterations in endothelial cell adhesion and migration

Highlights: Black-Right-Pointing-Pointer We explore the role of RhoA in endothelial cell response to ionizing radiation. Black-Right-Pointing-Pointer RhoA is rapidly activated by single high-dose of radiation. Black-Right-Pointing-Pointer Radiation leads to RhoA/ROCK-dependent actin cytoskeleton remodeling. Black-Right-Pointing-Pointer Radiation-induced apoptosis does not require the RhoA/ROCK pathway. Black-Right-Pointing-Pointer Radiation-induced alteration of endothelial adhesion and migration requires RhoA/ROCK. -- Abstract: Endothelial cells of the microvasculature are major target of ionizing radiation, responsible of the radiation-induced vascular early dysfunctions. Molecular signaling pathways involved in endothelial responses to ionizing radiation, despite being increasingly investigated, still need precise characterization. Small GTPase RhoA and its effector ROCK are crucial signaling molecules involved in many endothelial cellular functions. Recent studies identified implication of RhoA/ROCK in radiation-induced increase in endothelial permeability but other endothelial functions altered by radiation might also require RhoA proteins. Human microvascular endothelial cells HMEC-1, either treated with Y-27632 (inhibitor of ROCK) or invalidated for RhoA by RNA interference were exposed to 15 Gy. We showed a rapid radiation-induced activation of RhoA, leading to a deep reorganisation of actin cytoskeleton with rapid formation of stress fibers. Endothelial early apoptosis induced by ionizing radiation was not affected by Y-27632 pre-treatment or RhoA depletion. Endothelial adhesion to fibronectin and formation of focal adhesions increased in response to radiation in a RhoA/ROCK-dependent manner. Consistent with its pro-adhesive role, ionizing radiation also decreased endothelial cells migration and RhoA was required for this inhibition. These results highlight the role of RhoA GTPase in ionizing radiation-induced deregulation of essential endothelial functions linked to actin cytoskeleton.

60 APPLIED LIFE SCIENCES↗

Vasostatin-2 inhibits cell proliferation and adhesion in vascular smooth muscle cells, which are associated with the progression of atherosclerosis

Recently, the serum expression level of vasostatin-2 was found to be reduced and is being studied as an important indicator to assess the presence and severity of coronary artery disease; the functional properties of vasostatin-2 and its relationship with the development of atherosclerosis remains unclear. In this study, we attempted to detect the expression of vasostatin-2 and its impact on human vascular smooth muscle cells (VSMCs). Quantitative real-time PCR (qRT-PCR) and western blot were used to assess the expression level of vasostatin-2 in VSMCs between those from atherosclerosis and disease-free donors; we found that vasostatin-2 was significantly down-regulated in atherosclerosis patient tissues and cell lines. In addition, the over-expression of vasostatin-2 apparently inhibits cell proliferation and migration in VSMCs. Gain-of-function in vitro experiments further show that vasostatin-2 over-expression significantly inhibits inflammatory cytokines release in VSMCs. In addition, cell adhesion experimental analysis showed that soluble adhesion molecules (sICAM-1, sVCAM-1) had decreased expression when vasostatin-2 was over-expressed in VSMCs. Therefore, our results indicate that vasostatin-2 is an atherosclerosis-related factor that can inhibit cell proliferation, inflammatory response and cell adhesion in VSMCs. Taken together, our results indicate that vasostatin-2 could serve as a potential diagnostic biomarker and therapeutic option for human atherosclerosis in the near future. - Highlights: • Vasostatin-2 levels were down-regulated in atherosclerosis patient tissues and VSMCs. • Ectopic expression of vasostatin-2 directly affects cell proliferation and migration in vitro. • Ectopic expression of vasostatin-2 protein affects pro-inflammatory cytokines release in VSMCs. • Ectopic expression of vasostatin-2 protein affects cell adhesion in VSMCs.

60 APPLIED LIFE SCIENCES↗

Improved adhesion of polyurethane-based nanocomposite coatings to tin surface through silane coupling agents

Conformal coatings with higher adhesion strength is critical for mitigating the growth of whiskers from the pure tin (Sn) or Sn-rich surfaces of the Pb-free electronics. Silane coupling agents have the ability to form a durable bond between polymeric coatings and metallic materials. The main goal of this paper is to investigate the effect of silane agents on the adhesion behavior of polyurethane (PU), polyurethane acrylate (PUA) and both coatings filled with silicone rubber (SR) nanoparticles on the tin solder pads. It was found that an isocyanate-based silane provided excellent adhesion for PU and PU + SR coatings and an acrylic-based silane for PUA and PUA + SR coatings on the tin surface. This was due to the reaction bond formation between the silane coupling agent and the coating. Hence, the selection of silane coupling agents with the organofunctional group similar to the coating material is crucial to improve the adhesion properties of the coating.

36 MATERIALS SCIENCE↗

Self-adhesive ionomers for durable low-temperature anion exchange membrane electrolysis

Low-temperature water electrolysis using an anion conductive polymer electrolyte has several potential advantages over other technologies, however, the fabrication of durable alkaline electrodes remains a challenge. Detachment of catalysts results in the loss of electrochemical surface area. Simple mixtures of ionomer and catalyst can suffer from poor catalyst adhesion because only physical adhesion is used to bind the components together. A family of chemically bonded, self-adherent, hydroxide conducting ionomers were synthesized and tested under alkaline electrolysis conditions with nickel ferrite anode electrocatalysts and platinum-nickel cathode catalyst. The ionomers are based on hydroxide conducting poly(norbornene) polymers used as the solid polymer electrolyte in alkaline fuel cells and electrolyzers. The synthesized terpolymer ionomers have been functionalized to provide pendant sites for covalent chemical bonding of bis(phenyl)-A-diglycidyl ether to the ionomer, catalyst, and porous transport layer. The electrodes show excellent adhesion between the catalyst particles, porous transport layer and ionomer, as determined by adhesion measurements and electrolysis performance. As a result, the AEM electrolyzer had stable voltage performance under high current density (1 A/ cm 2 at 1.83 V (67% voltage efficiency)) for extended time periods (>600 h) without degradation.

08 HYDROGEN↗

Regulation of promyogenic signal transduction by cell-cell contact and adhesion

Skeletal myoblast differentiation involves acquisition of the muscle-specific transcriptional program and morphological changes, including fusion into multinucleated myofibers. Differentiation is regulated by extracellular signaling cues, including cell-cell contact and adhesion. Cadherin and Ig adhesion receptors have been implicated in distinct but overlapping stages of myogenesis. N-cadherin signals through the Ig receptor Cdo to activate p38 MAP kinase, while the Ig receptor neogenin signals to activate FAK; both processes promote muscle-specific gene expression and myoblast fusion. M-cadherin activates Rac1 to enhance fusion. Specific Ig receptors (Kirre and Sns) are essential for myoblast fusion in Drosophila, also signaling through Rac, and vertebrate orthologs of Kirre and Sns have partially conserved function. Mice lacking specific cytoplasmic signaling factors activated by multiple receptors (e.g., Rac1) have strong muscle phenotypes in vivo. In contrast, mice lacking individual adhesion receptors that lie upstream of these factors have modest phenotypes. Redundancy among receptors may account for this. Many of the mammalian Ig receptors and cadherins associate with each other, and multivalent interactions within these complexes may require removal of multiple components to reveal dramatic defects in vivo. Nevertheless, it is possible that the murine adhesion receptors rate-limiting in vivo have not yet been identified or fully assessed.

60 APPLIED LIFE SCIENCES↗

Annexin A6 contributes to the invasiveness of breast carcinoma cells by influencing the organization and localization of functional focal adhesions

The interaction of annexin A6 (AnxA6) with membrane phospholipids and either specific extracellular matrix (ECM) components or F-actin suggests that it may influence cellular processes associated with rapid plasma membrane reorganization such as cell adhesion and motility. Here, we examined the putative roles of AnxA6 in adhesion-related cellular processes that contribute to breast cancer progression. We show that breast cancer cells secrete annexins via the exosomal pathway and that the secreted annexins are predominantly cell surface-associated. Depletion of AnxA6 in the invasive BT-549 breast cancer cells is accompanied by enhanced anchorage-independent cell growth but cell-cell cohesion, cell adhesion/spreading onto collagen type IV or fetuin-A, cell motility and invasiveness were strongly inhibited. To explain the loss in adhesion/motility, we show that vinculin-based focal adhesions in the AnxA6-depleted BT-549 cells are elongated and randomly distributed. These focal contacts are also functionally defective because the activation of focal adhesion kinase and the phosphoinositide-3 kinase/Akt pathway were strongly inhibited while the MAP kinase pathway remained constitutively active. Compared with normal human breast tissues, reduced AnxA6 expression in breast carcinoma tissues correlates with enhanced cell proliferation. Together this suggests that reduced AnxA6 expression contributes to breast cancer progression by promoting the loss of functional cell-cell and/or cell-ECM contacts and anchorage-independent cell proliferation.

60 APPLIED LIFE SCIENCES↗

The Src homology 2 protein Shb promotes cell cycle progression in murine hematopoietic stem cells by regulation of focal adhesion kinase activity

The widely expressed adaptor protein Shb has previously been reported to contribute to T cell function due to its association with the T cell receptor and furthermore, several of Shb's known interaction partners are established regulators of blood cell development and function. In addition, Shb deficient embryonic stem cells displayed reduced blood cell colony formation upon differentiation in vitro. The aim of the current study was therefore to explore hematopoietic stem and progenitor cell function in the Shb knockout mouse. Shb deficient bone marrow contained reduced relative numbers of long-term hematopoietic stem cells (LT-HSCs) that exhibited lower proliferation rates. Despite this, Shb knockout LT-HSCs responded promptly by entering the cell cycle in response to genotoxic stress by 5-fluorouracil treatment. In competitive LT-HSC transplantations, Shb null cells initially engrafted as well as the wild-type cells but provided less myeloid expansion over time. Moreover, Shb knockout bone marrow cells exhibited elevated basal activities of focal adhesion kinase/Rac1/p21-activated kinase signaling and reduced responsiveness to Stem Cell Factor stimulation. Consequently, treatment with a focal adhesion kinase inhibitor increased Shb knockout LT-HSC proliferation. The altered signaling characteristics thus provide a plausible mechanistic explanation for the changes in LT-HSC proliferation since these signaling intermediates have all been shown to participate in LT-HSC cell cycle control. In summary, the loss of Shb dependent signaling in bone marrow cells, resulting in elevated focal adhesion kinase activity and reduced proliferative responses in LT-HSCs under steady state hematopoiesis, confers a disadvantage to the maintenance of LT-HSCs over time. -- Highlights: • Shb is an adaptor protein operating downstream of tyrosine kinase receptors. • Shb deficiency reduces hematopoietic stem cell proliferation. • The proliferative effect of Shb occurs via increased focal adhesion kinase activity. • Shb is critical for the long-term maintenance of the hematopoietic stem cell pool.

60 APPLIED LIFE SCIENCES↗