Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “X RADIATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Implications of Abiotic Oxygen Buildup for Earth-like Complex Life

One of the chief paradoxes of molecular oxygen (O{sub 2}) is that it is an essential requirement for multicellular eukaryotes on Earth while simultaneously posing a threat to their survival via the formation of reactive oxygen species. In this paper, the constraints imposed by O{sub 2} on Earth-like complex life are invoked to explore whether worlds with abiotic O{sub 2} inventories can harbor such organisms. By taking the major O{sub 2} sources and sinks of Earth-like planets into account using a simple model, it is suggested that worlds that receive time-averaged X-ray and extreme ultraviolet fluxes that are ≳10 times higher than Earth might not be capable of hosting complex lifeforms because the photolysis of molecules such as water may lead to significant O{sub 2} buildup. Methods for testing this hypothesis by searching for anticorrelations between biosignatures and indicators of abiotic O{sub 2} atmospheres are described. In the event, however, that life successfully adapts to high-oxygen environments, these worlds could permit the evolution of large and complex organisms.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

The 2024 July 16 solar event: a challenge to the coronal mass ejection origin of long-duration gamma-ray flares

We present a multi-spacecraft analysis of the 2024 July 16 long-duration gamma-ray flare (LDGRF) detected by the Large Area Telescope on the Fermi satellite. The measured > 100 MeV γ-ray emission persisted for over seven hours after the flare impulsive phase, and was characterized by photon energies exceeding 1 GeV and a remarkably hard parent-proton spectrum. In contrast, the phenomena related to the coronal mass ejection (CME)-driven shock linked to this eruption were modest, suggesting an inefficient proton acceleration unlikely to achieve energies well above the 300 MeV pion-production threshold to account for the observed γ-ray emission. Specifically, the CME was relatively slow (∼600 km/s) and the accompanying interplanetary type-II/III radio bursts were faint and short-lived, unlike those typically detected during large events. In particular, the type-II emission did not extend to kilohertz frequencies and disappeared ∼5.5 hours prior to the LDGRF end time. Furthermore, the associated solar energetic particle (SEP) event was very weak, short-duration, and limited to a few tens of MeV, even at magnetically well-connected spacecraft. These findings demonstrate that a very fast CME resulting in a high-energy SEP event is not a necessary condition for the occurrence of LDGRFs, challenging the idea that the high-energy γ-ray emission is produced by the back-precipitation of shock-accelerated ions into the solar surface. The alternative origin scenario based on local particle trapping and acceleration in large-scale coronal loops is instead favored by the observation of giant arch-like structures of hot plasma over the source region that persisted for the entire duration of this LDGRF.

Sun: UV radiation↗
DOE OSTI2026

thornado+FLASH-X: A Hybrid Discontinuous Galerkin–Implicit-explicit and Finite-volume Framework for Neutrino-radiation Hydrodynamics in Core-collapse Supernovae

We present neutrino-transport algorithms implemented in the toolkit for high-order neutrino-radiation hydrodynamics (thornado) and their coupling to self-gravitating hydrodynamics within the adaptive mesh refinement–based multiphysics simulation framework FLASH-X. thornado, developed primarily for simulations of core-collapse supernovae (CCSNe), employs a spectral, six-species two-moment formulation with algebraic closure and special-relativistic observer corrections accurate to $\mathcal{O}(v/c)$, and uses discontinuous Galerkin (DG) methods for phase-space discretization combined with implicit-explicit time stepping. A key development is a nonlinear neutrino–matter coupling algorithm based on nested fixed-point iteration with Anderson acceleration, enabling fully implicit treatment of collisional processes, including energy-coupling interactions such as neutrino–electron scattering and pair production. Coupling to finite-volume (FV) hydrodynamics is achieved through a hybrid DG-FV representation of the fluid variables and operator-split evolution within FLASH-X. The implementation is verified using basic transport tests with idealized opacities and relaxation and deleptonization problems with tabulated microphysics. Spherically symmetric CCSN simulations demonstrate accuracy and robustness of the coupled scheme, including close agreement with the CCSN simulation code Chimera. An axisymmetric CCSN simulation further demonstrates the viability of DG-based neutrino transport for multidimensional supernova modeling within FLASH-X. thornado’s neutrino-transport solver is GPU-enabled using OpenMP offloading or OpenACC, and all CCSN applications included in this work use the GPU implementation. Together, these results establish a foundation for future enhancements in physics fidelity, numerical algorithms, and computational performance, for increasingly realistic large-scale CCSN simulations.

Endeve, Eirik [Oak Ridge National Laboratory (ORNL↗
DOE OSTI2021

Ligand assisted growth of perovskite single crystals with low defect density

A low defect density in metal halide perovskite single crystals is critical to achieve high performance optoelectronic devices. Here we show the reduction of defect density in perovskite single crystals grown by a ligand-assisted solution process with 3-(decyldimethylammonio)-propane-sulfonate inner salt (DPSI) as an additive. DPSI ligands anchoring with lead ions on perovskite crystal surfaces not only suppress nucleation in solution, but also regulate the addition of proper ions to the growing surface, which greatly enhances the crystal quality. The grown CH 3 NH 3 PbI 3 crystals show better crystallinity and a 23-fold smaller trap density of 7 × 10 10 cm -3 than the optimized control crystals. The enhanced material properties result in significantly suppressed ion migration and superior X-ray detection sensitivity of CH 3 NH 3 PbI 3 detectors of (2.6 ± 0.4) × 10 6 µC Gy -1 air cm -2 for 60 kVp X-ray and the lowest detectable dose rate reaches (5.0 ± 0.7) nGy s -1 , which enables reduced radiation dose to patients in medical X-ray diagnostics.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Discovery of a bright extended X-ray jet in RGB J1512+020A

ABSTRACT We report the discovery of a bright, extended X-ray jet in the quasar RGB J1512+020A (z = 0.22). Chandra observations show the X-ray core and 13 arcsec (∼45 kpc projected) extended emission coincident with the radio jet. The jet stands out as one of brightest X-ray jets (LX ∼ 7 × 1043 erg s−1) at low redshift (z < 0.5) discovered so far, with remarkably large X-ray to radio luminosity ratios (LX/Lr up to ∼50). We identified four main components, two unresolved knots and two extended structures, one being the jet brightest feature (JBF). All jet features are also detected in ALMA archival observations. The radio, sub-mm to X-ray spectra of the two knots can be modelled with a single synchrotron component. For the two resolved structures, the ALMA data unveil a turnover of the low-energy continuum at ∼460 GHz. External Comptonization of cosmic microwave background photons can account for the observed X-ray emission if the jet speed remains highly relativistic, with bulk motion Γbulk > 15, up to tens of kiloparsec from the core. However, the comparison with the spectral energy distribution of similar X-ray detected jets shows that the alternative hypothesis of synchrotron emission from an additional population of ultra-high-energy electrons is also possible. We report a tentative (≳2σ) optical detection of the JBF in images of the Dark Energy Camera Legacy Survey. If confirmed, the optical emission should be either the low-energy tail of the radiative component responsible for the X-ray emission or a third, separate component.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

The effect of autoionization on the HBr + X 2 Π 3/2,1/2 state photoelectron angular distributions

A double-imaging photoelectron-photoion spectrometer and synchrotron radiation have been used to measure the HBr + X 2 Π 3/2 v + = 0, 1, 2 and the 2 Π 1/2 v + = 0 state photoelectron angular distributions, as characterized by the anisotropy parameter β , the total ion yield, and the threshold photoelectron spectrum. Particular attention has been focussed on the photon energy range between the 2 Π 3/2 and the 2 Π 1/2 spin–orbit components of the ground ionic state. This region encompasses Rydberg states, belonging to series converging onto the upper 2 Π 1/2 ionization limit, which may decay by autoionization into the 2 Π 3/2 ionization continuum. A detailed study has been performed on the effects of autoionization on the 2 Π 3/2 v + = 0 state photoelectron angular distributions. Furthermore, the observed energy dependent variations in the β -values exhibit a regular pattern that correlates with excitation into members of a very broad d-type Rydberg series. Additional rapid variations in the β -parameters, which occur over a narrow energy range, appear to coincide with sharp autoionizing Rydberg states belonging to s, p and d series. The present experimental results for the HBr + X 2 Π 3/2 v + = 0 state photoelectron anisotropy parameter are compared to previously reported theoretical predictions and to earlier studies of the Kr + 4p 5 2 P 3/2 state β -parameter. The threshold photoelectron spectrum of the X 2 Π 3/2 v + = 0 band exhibits partially resolved rotational structure. A simulation of this structure yields an ionization threshold of 11.6673 ± 0.0010 eV, which is consistent with previous measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Orbital Hybridization and Magnetic Coupling at Cuprate–Manganite Interfaces Driven by Manganite Doping

Fundamental understanding of interface mechanisms that generate unexpected physical properties in the cuprate/manganite heterostructures is essential for possible applications as spintronic devices. In this study, CaCuO 2 /La 1–x Sr x MnO 3 (CCO/LSMO) superlattices are investigated, where the infinite-layer cuprate CCO does not have apical oxygen for Cu in the Ca-plane so that the Mn–O–Cu superexchange coupling can be only present at the MnO 2 –(La,Sr)O–CuO 2 interface. Two different doping states for the manganites are studied, namely x = 0.1 and x = 0.3, corresponding to the ferromagnetic insulating and ferromagnetic metallic states, respectively, in the manganite phase diagram. Linear and circular dichroism in X-ray absorption by synchrotron radiation at Cu and Mn L-edges clearly demonstrate that in the absence of apical oxygen in the cuprate block, the magnetic coupling between the LSMO and CCO is weakly ferromagnetic when LSMO is metallic, while it is antiferromagnetic when LSMO is insulating, along with an increased Cu 3d(3z 2 –r 2 ) and Mn 3d(3z 2 –r 2 ) orbital occupation. It is proposed that the Mn 3d valence band upward shift driven by the enhancement of Mn 3+ content in the underdoped sample enhances the orbital hybridization. The stronger hybridization at the interface MnO 2 –(La,Sr)O–CuO 2 gives rise to the antiferromagnetic coupling between cuprate and underdoped manganite.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Elucidating the structural properties and reversible regional texture effect of GdB 6 under high pressure

As hard and refractory materials with high chemical resistance and mechanical strength, lanthanide hexaborides (LnB 6 ) have attracted much attention. Among the family of LnB 6 , gadolinium hexaboride (GdB 6 ) occupies a special position due to the half-filled 4f shell of Gd. Here, using in situ synchrotron radiation angle-dispersive X-ray diffraction in a diamond anvil cell at room temperature, the structural stability and compression behavior of GdB 6 are investigated extensively, GdB 6 is observed to be structurally stable up to 73 GPa, and the bulk modulus of 177 GPa is obtained under hydrostatic compression. In this paper, an interesting observation of pressure-induced spotty diffraction rings of GdB6 is reported, its formation mechanism can be well described by the reversible regional texture effect, which highlights the rearrangement of crystal grains under high pressure. The rearrangement mechanism has been well explained by investigating the pressure dependence of full width at half maximum, macro-differential stress and grain size. Collective grain rotation behavior motivated by stress difference is critical for the rearrangement process, the strong isotropy and strong stability of GdB 6 structure also provide necessary conditions for high-pressure grain rotation behavior. These results will help to promote the understanding of high-pressure structural properties of GdB 6 , and provide novel insights on the high-pressure grain behavior in hard materials with strong isotropy and three-dimensional skeleton constituted of strong covalent bonds.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Post-irradiation examination of commercial tantalum alloys following neutron irradiation

Post irradiation examination of two commercial tantalum alloys (based on Ta-8 %W) revealed significant irradiation hardening following neutron irradiation in the High Flux Isotope Reactor at Oak Ridge National Laboratory. Tensile samples of commercial Ta alloys T-111 and ASTAR-811C were irradiated to a total neutron fluence (E > 0.1 MeV) in the range (2–4)x10 21 n/cm 2 (0.39–0.75 dpa) at an irradiation temperature near 900 °C. Tensile testing conducted at room temperature and at 800 °C revealed significant irradiation hardening under all test conditions. Samples that were tensile tested at room temperature exhibited brittle failure, whereas ductility was maintained for elevated temperature testing. The irradiation hardening and embrittlement noted for both alloys was attributed to irradiation-induced dislocation loop formation as confirmed through scanning transmission electron microscopy analysis. Corresponding energy dispersive x-ray spectroscopy revealed radiation-induced segregation of Hf in these loop populations. This Hf enrichment is shown to result in eventual co-precipitation of elongated (Hf,O)-rich precipitates along the dislocation loops. Further, these results show that irradiation hardening is enhanced via irradiation-enhanced precipitation at elevated irradiation temperatures. Consequently, the minimum recommended operating temperature window for Ta alloys should be increased to account for observed hardening/embrittlement at irradiation temperatures as high as 900 °C (1,173 K).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Spatiotemporal mapping of microscopic strains and defects to reveal Li-dendrite-induced failure in all-solid-state batteries

Solid-state electrolytes (SSEs) are key to the success and reliability of all-solid-state lithium batteries, potentially enabling improvements in terms of safety and energy density over state-of-the-art lithium-ion batteries. However, there are several critical challenges to their implementation, including the interfacial instability stemming from the dynamic interaction of as-formed dendritic lithium during cycling. Here, we emphasize the importance of studying the spatial distribution and temporal evolution of strains and defects in crystalline solid-state electrolytes at the micro-scale, and how this affects dendrite growth. A proof-of-principle study is demonstrated using the synchrotron radiation based micro Laue X-ray diffraction method, and a custom-developed in-situ cycling device. Defects and residual strains are mapped, and the evolution of intragranular misorientation is observed. The feasibility of using this technique is discussed, and recommendations for micro-strain engineering to address the Li/SSEs interfacial issues are given. Additionally, work directions are pointed out with the consideration of combining multi-techniques for “poly-therapy”.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructural stability of tantalum-alloyed ferritic-martensitic steel with neutron irradiation to 7.4 dpa at ~490 °C

Specimens of a reduced-activation ferritic-martensitic steel, called CNA1, were irradiated to 7.4 displacements per atom at ~490 °C in the High Flux Isotope Reactor. Vickers hardness and tensile properties revealed consistent softening that is attributed to some recovery during irradiation, with reduced laths and dislocation density. Detailed microstructural characterization by transmission electron microscopy and energy dispersive x-ray spectroscopy showed radiation-induced dislocation loops, few cavities, and slight dissolution of M 23 C 6 and MX precipitates. Partial amorphization was only observed in M 23 C 6 precipitated in matrix. Transmutation somewhat destabilized M 23 C 6 and MX, with a stronger effect on the later one by noticeable depletion of Ta with enriched W, which is consistent with the transmutation calculations. The microstructural evolution and associated strength changes were discussed with the assistance of computational thermodynamics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The O K -2 V spectrum of CO: the influence of the second core-hole

Using synchrotron radiation in the tender X-ray regime, a photoelectron spectrum showing the formation of single site double-core-hole pre-edge states, involving the K shell of the O atom in CO, has been recorded by means of high-resolution electron spectroscopy. The experimentally observed structures have been simulated, interpreted and assigned, employing state-of-the-art ab initio quantum chemical calculations, on the basis of a theoretical model, accounting for their so-called direct or conjugate character. Features appearing above the double ionization threshold have been reproduced by taking into account the strong mixing between multi-excited and continuum states. The shift of the σ* resonance below the double ionization threshold, in combination with the non-negligible contributions of multi-excited configurations in the final states reached, gives rise to a series of avoided crossings between the different potential energy curves.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2022

Thermal conductivity evaluation of ion irradiated Si 3 N 4 and ZrN ceramics using spatial domain thermoreflectance

Nitride ceramics have been investigated for different applications in the nuclear industry, such as space nuclear power, fusion reactor diagnostics and plasma heating, inert matrix fuels, and accident tolerant fuels. Although thermal conductivity remains one of the most important properties to track following irradiation, traditional techniques such as laser flash and xenon flash are limited to bulk sample characterization, which requires lengthy and cost-consuming neutron irradiation. This work used spatial domain thermoreflectance (SDTR) for the micrometer-scale measurement of thermal conductivity in 15 MeV Ni ion-irradiated silicon nitride and zirconium nitride from 1 to 50 dpa and 300 to 700 °C. Here, the SDTR-measured unirradiated thermal conductivity was found to be consistent with the published data on bulk samples. Electrically conductive ZrN exhibits modest reduction after irradiation which is minimal at the highest irradiation temperatures. In electrically insulating Si 3 N 4 , the reduction is more significant and unlike ZrN, the reduction remains significant even at a higher irradiation temperature. The thermal resistance evolution following irradiation was compared with lattice swelling, which was determined using grazing incidence x-ray diffraction, and radiation-induced defects were observed using transmission electron microscopy. A saturation value was observed between 15 and 50 dpa for thermal conductivity degradation in both nitride ceramics and a direct correlation with high-temperature defect recombination was observed, as well as the potential presence of additional carrier scattering mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2023

TOI-908: a planet at the edge of the Neptune desert transiting a G-type star

ABSTRACT We present the discovery of an exoplanet transiting TOI-908 (TIC-350153977) using data from TESS sectors 1, 12, 13, 27, 28, and 39. TOI-908 is a T = 10.7 mag G-dwarf (Teff = 5626 ± 61 K) solar-like star with a mass of 0.950 ± 0.010 M⊙ and a radius of 1.028 ± 0.030 R⊙. The planet, TOI-908 b, is a 3.18 ± 0.16 R⊕ planet in a 3.18 d orbit. Radial velocity measurements from HARPS reveal TOI-908 b has a mass of approximately 16.1 ± 4.1 M⊕, resulting in a bulk planetary density of $2.7^{+0.2}_{-0.4}$ g cm−3. TOI-908 b lies in a sparsely populated region of parameter space known as the Neptune desert. The planet likely began its life as a sub-Saturn planet before it experienced significant photoevaporation due to X-rays and extreme ultraviolet radiation from its host star, and is likely to continue evaporating, losing a significant fraction of its residual envelope mass.

Hawthorn, Faith (ORCID:000000028675182X)↗
DOE OSTI2022

Use of diamond sensors for a high-flux, high-rate X-ray pass-through diagnostic

X-ray free-electron lasers (XFELs) deliver pulses of coherent X-rays on the femtosecond time scale, with potentially high repetition rates. While XFELs provide high peak intensities, both the intensity and the centroid of the beam fluctuate strongly on a pulse-to-pulse basis, motivating high-rate beam diagnostics that operate over a large dynamic range. The fast drift velocity, low X-ray absorption and high radiation tolerance properties of chemical vapour deposition diamonds make these crystals a promising candidate material for developing a fast (multi-GHz) pass-through diagnostic for the next generation of XFELs. A new approach to the design of a diamond sensor signal path is presented, along with associated characterization studies performed in the XPP endstation of the LINAC Coherent Light Source (LCLS) at SLAC. Qualitative charge collection profiles (collected charge versus time) are presented and compared with those from a commercially available detector. Quantitative results on the charge collection efficiency and signal collection times are presented over a range of approximately four orders of magnitude in the generated electron–hole plasma density.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Algorithm-Driven Advances for Scientific CT Instruments: From model-based to deep learning-based approaches

Multiscale 3D characterization is widely used by materials scientists to further their understanding of the relationships between microscopic structure and macroscopic function. Scientific computed tomography (SCT) instruments are one of the most popular choices for 3D nondestructive characterization of materials at length scales ranging from the angstrom scale to the micron scale. These instruments typically have a source of radiation (such as electrons, X-rays, or neutrons) that interacts with the sample to be studied and a detector assembly to capture the result of this interaction (see Figure 1 ). A collection of such high-resolution measurements is made by reorienting the sample, which is mounted on a specially designed stage/holder after which reconstruction algorithms are used to produce the final 3D volume of interest. The specific choice of which instrument to use depends on the desired resolution and properties of the materials being imaged. Additionally, the end goal of SCT scans includes determining the morphology, chemical composition, or dynamic behavior of materials when subjected to external stimuli. In summary, SCT instruments are powerful tools that enable 3D characterization across multiple length scales and play a critical role in furthering the understanding of the structure–function relationships of different materials.

42 ENGINEERING↗
DOE OSTI2024

Study of electro-physical properties of CsPbBr3 perovskite single crystals

Methods have been developed for the synthesis and growth of lead halide perovskites CsPbBr3, which can be used as detectors of optical, X-ray and gamma-radiation. Single crystals of these compounds were grown by the Bridgman method. The melt temperature was 580 °C, the gradient at the crystallization front was 5 K/cm, and the ampoule lowering speed was 3 mm/hour. In this work, the electro-physical properties of the inorganic perovskite CsPbBr3 were investigated. Crystals for research were cut from the beginning and end of the ingot. The optical absorption spectra were measured depending on the crystal thickness and temperature, the differential resistivity dif and the product  were determined from the I-V characteristics. It was established that dif practically does not change for samples made from the beginning and the end of the ingot, and is dif  21010 Ωcm at 100 V and 293 K.

Sklyarchuk, V.↗
DOE OSTI2025

Sparse measurement medical CT reconstruction using multi-fused block matching denoising priors

A major challenge for medical X-ray CT imaging is reducing the number of X-ray projections to lower radiation dosage and reduce scan times without compromising image quality. However these under-determined inverse imaging problems rely on the formulation of an expressive prior model to constrain the solution space while remaining computationally tractable. Traditional analytical reconstruction methods like Filtered Back Projection (FBP) often fail with sparse measurements, producing artifacts due to their reliance on the Shannon-Nyquist Sampling Theorem. Consensus Equilibrium, which is a generalization of Plug and Play, is a recent advancement in Model-Based Iterative Reconstruction (MBIR), has facilitated the use of multiple denoisers are prior models in an optimization free framework to capture complex, non-linear prior information. However, 3D prior modelling in a Plug and Play approach for volumetric image reconstruction requires long processing time due to high computing requirement. Instead of directly using a 3D prior, this work proposes a BM3D Multi Slice Fusion (BM3D-MSF) prior that uses multiple 2D image denoisers fused to act as a fully 3D prior model in Plug and Play reconstruction approach. Our approach does not require training and are thus able to circumvent ethical issues related with patient training data and are readily deployable in varying noise and measurement sparsity levels. In addition, reconstruction with the BM3D-MSF prior achieves similar reconstruction image quality as fully 3D image priors, but with significantly reduced computational complexity. We test our method on clinical CT data and demonstrate that our approach improves reconstructed image quality.

Hossain, Maliha [ORNL]↗