Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WAVEGUIDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Evaporated As2S3 Luneburg lenses for LiNbO3:Ti optical waveguides

Luneburg lenses of good quality were formed on high index optical waveguides by evaporation of arsenic trisulfide glass through simple masks. Using only two thin circular aperture masks, lenses with focal spots of a few times the diffraction limited width at f/4 were obtained. These lenses were designed for and tested at both visible (633 nm) and infrared wavelengths. Procedures for the design, fabrication, and testing of lenses of this type are described.

Busch, J. R.↗
NASA NTRS1982

Studies of single-mode injection lasers and of quaternary materials. Volume 2: Measurement of electro-optic effects in InGaAsP junction waveguides

Both the linear electro-optic (Pockel's) effect and electroabsorption (Franz-Keldysh effect) in waveguiding junctions of InGaAsP were measured. The electro-optic coefficient is found to be 0.1-0.14x10 to the -12 power m/V at lambda = 1.54 - 1.65 micrometers. Possibly this is the first reported measurement of the electro-optic coefficient for InGaAsP. The value found for the electroabsorption is on the order of 7x10 to the -4 power cm to the -1 power/(V/cm) or approximately 100 cm/1 for fields of 200,000 V/cm at lambda 1.3 micrometers. All measurements were made on a quaternary film with a bandgap wavelength of 1.23 micrometers. Because of the rapid commercial introduction of quaternary lasers, LEDs, and detectors to take advantage of large optical fiber bandwidths and low losses in the 1.2- to 1.7- micrometer region, these measurements are significant in providing some of the basic physical constants needed to design modulators and switches capable of operating at microwave frequencies in this wavelength region.

Hammer, J. M.↗
NASA NTRS1982

Radiation from an open-ended waveguide with beam equalizer - A spectral domain analysis

A septum and an impedance matching post are used as a beam equalizer in an open-ended waveguide feed for reflectors used in satellite communications systems. The performance of this design over a frequency band is evaluated using a spectral domain approach. The computed radiation patterns in the E- and H-planes, as well as the results for the impedance match are presented.

Ko, W. L.↗
NASA NTRS1982

Optogalvanic stabilization and offset tuning of a carbon dioxide waveguide laser

A feedback loop employing the change in discharge impedance with output power is used to stabilize the frequency of a CO2 waveguide laser. The relatively high operating pressure of the laser combined with a zero offset feature in the feedback loop allows continuous tuning of the stabilized frequency over a 300-400 MHz range.

Kavaya, M. J.↗
NASA NTRS1982

Novel solution of 2-D waveguides using the finite element method

A novel technique is described for solving 2-D waveguide equations using the finite element method. The full-wave equation is solved, thus automatically taking care of various inhomogeneities in the medium. The solution yields the transverse components of the field, which are useful for calculating far-field radiation patterns.

Katz, J.↗
NASA NTRS1983

Fabricating Slotted-Waveguide Arrays From Sheet Metal

Low-cost lightweight waveguides formed from rolls of aluminum. Array formed from sheared, punched, and bent aluminum sheets. Sheets alined with punched jig holes and joined by laser-beam or resistance spot welding. Process permits use of thin metal to reduce raw material costs and mass. Also holds closer tolerances than usually attained in sheet-metal work.

Brown, W. C.↗
NASA NTRS1982

Investigation of semiconductor clad optical waveguides

Glass waveguides are studied because of the ease and economy of fabricating devices in glass. All calculations are based on the assumption of a glass guide and substrate, but the effects being studied will occur on other materials if the proper refractive indices are used in the calculations.

Batchman, T. E.↗
NASA NTRS1982

Ultrapure glass optical waveguide development in microgravity by the sol-gel process

Containerless melting of glasses in space for the preparation of ultrapure homogeneous glass for optical waveguides is discussed. The homogenization of the glass using conventional raw materials is normally achieved on Earth either by the gravity induced convection currents or by the mechanical stirring of the melt. Because of the absence of gravity induced convection currents, the homogenization of glass using convectional raw materials is difficult in the space environment. Multicomponent, homogeneous, noncrystalline oxide gels can be prepared by the sol-gel process and these gels are promising starting materials for melting glasses in the space environment. The sol-gel process is based on the polymerization reaction of alkoxysilane with other metal alkoxy compounds or suitable metal salts. Many of the alkoxysilanes or other metal alkoxides are liquids and thus can be purified by distillation.

Source record↗
NASA NTRS1983

Ultrapure glass optical waveguide: Development in microgravity by the sol gel process

The sol-gel process for the preparation of homogeneous gels in three binary oxide systems was investigated. The glass forming ability of certain compositions in the selected oxide systems (SiO-GeO2, GeO2-PbO, and SiO2-TiO2) were studied based on their potential importance in the design of optical waveguide at longer wavelengths.

Mukherjee, S. P.↗
NASA NTRS1983

Spectrophone stabilization and offset tuning of a carbon dioxide waveguide laser

A sensitive spectrophone containing CO2 gas is incorporated into a feedback loop to stabilize the frequency of a CO2 waveguide laser. First or second harmonic detection combined with a zero offset feature and the relatively high operating pressure of the laser allows continuous tuning of the stabilized frequency over a 400 MHz range. Frequency stability of better than + or - 1 MHz is achieved.

Kavaya, M. J.↗
NASA NTRS1984

Investigation of RF excited CW CO2 waveguide lasers

The RF excited 2 to 3W CW CO2 waveguide lasers with lifetimes of the order of 10(4) to 2.10(4) hours were produced. This was achieved with CO and N2 bearing gas mixtures and with internal as well as external discharge electrodes. It is noted that these tests were conducted with unstabilized lasers which drift around in their signatures. The average power output was reduced to about one half of the highest peak power output in the signature. One of the lasers, no. 1.1, still shows 60% of its original output power after it was cycled on and off every 10 minutes for more than 50,000 times. The starting voltage and driving point impedance of the RF excited gas discharge structure for different gas pressures and mixtures were measured. These data will serve as a basis for the matching and starting network optimization. The second laser body was frit and indium sealed. To our a vacuum leak between the bore and electrode holes was noted. The leak seems to be due to a defect or crack in the BeO body.

Hochuli, U.↗
NASA NTRS1985

Normal modes in an overmoded circular waveguide coated with lossy material

The normal modes in an overmoded waveguide coated with a lossy material are analyzed, particularly for their attenuation properties as a function of coating material, layer thickness, and frequency. When the coating material is not too lossy, the low-order modes are highly attenuated even with a thin layer of coating. This coated guide serves as a mode suppressor of the low-order modes, which can be particularly useful for reducing the radar cross section (RCS) of a cavity structure such as a jet inlet. When the coating material is very lossy, low-order modes fall into two distinct groups: highly and lowly attenuated modes. However, as a/lambda (a = radius of the cylinder; lambda = the free-space wavelength) increases, the separation between these two groups becomes less distinctive. The attenuation constants of most of the low-order modes become small, and decrease as a function of lambda sup 2/a sup 3.

Lee, C. S.↗
NASA NTRS1983

Shaped reflector beam waveguide and high gain antenna systems

In this paper the problem of synthesizing dual reflector antennas for both amplitude and phase control of the final aperture distribution is discussed. An approximate procedure for the offset synthesis problem is presented and applications of the procedure to the shaping of beam waveguides and reflectors for high-gain antenna systems are illustrated.

Galindo-Israel, V.↗
NASA NTRS1983

Computer model for a waveguide relay link

A computer model used for design of a ground microwave data relay link is described. The link includes long runs of waveguide for which simulated high-speed data distortion is experimentally verified.

Jones, S. C.↗
NASA NTRS1985

Waveguide PIN junction electrooptic phase modulators Theoretical analysis and design criteria

Basic design equations for waveguide PIN heterojunction electrooptic phase modulators utilizing the linear electrooptic effect are derived, and criteria for optimum operation (in terms of obtainable phase shifts) are discussed. Although the numerical examples pertain to devices fabricated of the AlGaAs system on (100) substrates, the same method can be directly applied to modulators fabricated of other materials.

Marshall, W. K.↗
NASA NTRS1985

Propagation and radiation characteristics of a multimode corrugated waveguide feedhorn

A prototype of the multimode corrugated feedhorn which will be used in the 400 kW CW Ka-band radar system is described. A rough design is done using coupled mode theory and standard corrugated waveguide modes. A more exact analysis using mode matching techniques is then used which takes into account the effect of a finite number of corrugations per wavelength and determines the modes which are reflected from the device. A prototype feedhorn has been constructed and measured. These experimental results are then compared to the theoretical predictions which agree satisfactorily closely.

Hoppe, D.↗
NASA NTRS1986

Low-loss optical waveguides made with molecular beam epitaxial In(0.012)Ga(0.988)As and In(0.2)Ga(0.8)As-GaAs superlattices

Low-loss optical guiding in In-doped GaAs is demonstrated for the first time. Ridge waveguides are made with single In(0.012)Ga(0.988)As ternary layers and In(0.2)Ga(0.8)As-GaAs superlattices. Attenuation constants of about 1.3 dB/cm are measured and the principal loss mechanism is identified to be scattering at the ridge walls. It is expected that improved fabrication techniques will lead to guides with attenuation less than or equal to 0.5 dB/cm.

Das, U.↗
NASA NTRS1986

Normal modes in an overmoded circular waveguide coated with lossy material

The normal modes in an overmoded waveguide coated with a lossy material are analyzed, particularly for their attenuation properties as a function of coating material, layer thickness, and frequency. When the coating material is not too lossy, the low-order modes are highly attenuated even with a thin layer of coating. This coated guide serves as a mode suppressor of the low-order modes, which can be particularly useful for reducing the radar cross section of a cavity structure such as a jet engine inlet. When the coating material is very lossy, low-order modes fall into two distinct groups: highly and lowly attenuated modes. However, as a/lambda (a = radius of the cylinder; lambda = the free-space wavelength) increases, the separation between these two groups becomes less distinctive. The attenuation constants of most of the low-order modes become small and decrease as a function of lambda-squared/a-cubed.

Lee, C. S.↗