Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Tensile testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Accounting for the effect of dislocation climb-mediated flow on the anisotropy and texture evolution of Mg alloy, AZ31B

The current study explores the role that dislocation climb has in mediating plasticity a Mg alloy at moderately elevated temperatures. Interrupted tensile tests were performed on samples of Mg alloy, AZ31B, sheet in the O temper condition over a range of strain rates (10 -5 to 10 -1 s -1 ) and temperatures (20–350°C) along the rolling and transverse directions. Experimental measurements of the resulting strain anisotropy and texture evolution were used as constraints during a parametric study employing a new crystal plasticity model (VPSC-CLIMB), which explicitly accounts for the kinematics of dislocation climb. The results reveal that the climb of basal (a) dislocations is not only important for dislocation recovery, but also demonstrate that climb accommodates a significant fraction of the strain in conditions where a power-law creep-type constitutive response prevails. This work does not discredit the notion that non-basal slip of (a) and (c+a) dislocations is important over a wide range of temperatures and strain rates. However, it demonstrates that the activation of dislocation climb as the mechanistic change within the power law regime provides an explanation for a wide range of observations, including the simultaneous reduction in strain anisotropy, slowed texture evolution, and rapid increase in strain rate sensitivity. Finally, it is hypothesized that these conclusions may even apply to cases in which grain boundary sliding and/or dynamic recrystallization are observed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Repurposing the θ (Al 2 Cu) phase to simultaneously increase the strength and ductility of an additively manufactured Al–Cu alloy

The Al–Cu–Mn–Zr (ACMZ) cast family of alloys offers unique properties and value propositions for higher strength, higher temperature lightweight components of future vehicles. Earlier research has demonstrated trade-offs in the selection of the alloy chemistry in which an increase in Cu content from 6 up to 9 wt% improves hot tear resistance but lowers ductility. However, a recent study has demonstrated that higher-Cu (9Cu) ACMZ fabricated with laser powder bed fusion additive manufacturing (AM) results in an increase in both ductility and strength when compared to as-aged microstructure of cast 9Cu alloys. The mechanisms of differing mechanical performance of the cast and AM ACMZ alloys are elucidated in the current paper through the utilization of in situ high energy x-ray diffraction (HEXRD) tensile testing wherein lattice strains of different phases are calculated and correlated to their stresses. The ACMZ alloys consisted of theta (θ) and theta prime (θ') phases (both Al 2 Cu in nominal composition) within an aluminum matrix. The larger micron-size θ phase which decorated the grain boundaries in 9Cu ACMZ cast alloys recorded small lattice strains, while the submicron, homogeneously distributed θ phase in the 9Cu ACMZ AM alloy recorded considerably higher lattice strains. The maximum stress reached in the θ phase for the cast 9Cu alloy was found to be ~280 MPa, which was lower than the AM 9Cu alloy which registered a maximum stress of ~1.4 GPa. These measurements indicate that delayed fracture of the finer intermetallic phases simultaneously improves the ductility and strength of AM 9Cu alloy relative to the cast 9Cu alloy, which exhibits early fracture of the larger intermetallic particles.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Two-step deformation-induced martensitic transformation in additively manufactured High-Si stainless steel

Deformation-induced phase transformation in the additively manufactured (AM) Fe–18Cr–8Ni-5.5Si (in wt.%) alloy was analyzed using the in-situ electron backscattered diffraction (EBSD) record during uniaxial tensile testing in a scanning electron microscope (SEM). Analysis of EBSD data was focused to investigate phase transformation behavior during deformation with consideration of mechanical interactions among phases and grains in the ultrafine AM microstructure. The initial EBSD phase map illustrated that the as-built microstructure was a duplex structure consisting of major austenite (γ) and minor ferrite phases, some of which showed non-traditional orientation relationship since the rapid solidification in the AM process has produced non-equilibrium state in phase formation. In the deformed as-built AM alloy, the two-step martensitic transformation (γ→ε→α´) was identified as the main deformation-induced transformation mechanism. Martensitic transformation steps were found to be associated with glides of Shockley partial dislocations on closed packed (111) planes under the influence of atomic disturbance in the γ and ε phases, respectively. Using the closed-packed plane pole figures and unit cell orientations, their evolutions and mechanisms accompanying with the transformation were analyzed. Finally, the results indicate that one variant of ε-martensite forms from their parent γ phase, while two variants of α´ form from their parent ε phase.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Interfacial microstructure and mechanical properties of rotary inertia friction welded dissimilar 422 martensitic stainless steel to 4140 low alloy steel joints

In this work, dissimilar rotary inertia friction welds between 422 martensitic stainless steel and 4140 martensitic low-alloy steel were made to fabricate prototype heavy-duty diesel engine pistons. The influence of the inertia friction welding process and post weld heat treatment (PWHT) temperature on the interfacial microstructure evolutions and corresponding effects on mechanical properties of the 422/4140 welds were evaluated in detail. Carbon diffused from the 4140 side to the 422 side during PWHT at 650 °C for 1.5 h, causing the formation of a hard carbide-rich layer on the 422 side, and a softer but discontinuous C-depleted layer the 4140 side. PWHT at 700 °C for 1.5 h greatly accelerated C diffusion across the interface relative to 650 °C, resulting in a thicker hard carbide-rich layer and a relatively thick and continuous layer of coarse C-depleted grains (ferrite) on the 4140 side. In addition, the PWHT temperature greatly influenced the tensile properties and fracture behavior of the welds, with the 650 °C PWHT-ed samples failing predominately in a ductile manner in the 4140 heat affected zone during tensile testing. Conversely, the 700 °C PWHT specimens exhibited a strength reduction compared with the 650 °C PWHT specimens because of additional coarsening of the interfacial ferrite layer and softening of the base materials during PWHT, with brittle fracture between the hard and soft layers the predominate failure mechanism. Based on the findings, a reduced PWHT temperature and/or time, minimizing the hardness differential of the base metals, and pre-heating the 422 steel prior to welding are the potential pathways to achieve a more optimal balance between desirable tempering and stress relief of the weld microstructure and undesirable C migration across the weld interface, and to reduce the strength mismatch across the weld.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The influence of thermomechanical treatment pathways on texture and mechanical properties in ARB Cu/Nb nanolaminates

Accumulative roll-bonded Cu/Nb nanolaminates (ARB Cu/Nb) possess high strength, thermal stability, and radiation tolerance arising from a high content of heterophase interfaces at fine layer thicknesses. These properties can be tailored by processing parameters used in the ARB Cu/Nb fabrication process, in which layer thickness, thermal history, and strain pathway determine the interface types and resultant properties found in the material. In this work, we subject ARB Cu/Nb to annealing, and then two different rolling pathways – one where rolling direction is held constant (longitudinal rolling, or LR), and one where rolling direction is rotated by 90º and held constant thereafter (cross rolling, or CR). Rolling is performed on ARB Cu/Nb over a targeted range of layer thicknesses from 193 to 25 nm and resultant bulk textures measured by neutron diffraction are correlated with mechanical properties measured by miniaturized tensile tests. The annealing procedure sharpens texture in both phases. We find that Cu mostly develops the same texture in LR and CR. In contrast, Nb develops a distinct texture along the CR pathway that is distinct from the LR texture. The composite texture of Cu/Nb is thus distinct between LR and CR pathways. This difference in texture development between Cu and Nb as a function of strain after change in rolling direction demonstrates the viability for deliberate pairing of Cu LR and Nb CR textures at a desired layer thickness. For mechanical properties, we find that differences in texture do not result in yield or flow stress differences above a layer thickness of 25 nm. Below a layer thickness of 25 nm, despite similar Taylor factors, yield and flow stress and are significantly different. In conclusion, this indicates texture only influences mechanical behavior at low layer thickness, where interface structure dominates mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Considering interplay between multiple physical phenomena to elucidate single crystal-like texture, phase transformations, and mechanical behavior of directed energy deposited SS316L

A widespread implementation of large scale additive manufacturing (AM) processes, such as wire arc-directed energy deposition (WA-DED) AM can transform the current manufacturing supply chain networks. Naturally, such implementation requires control of the microstructural attributes, such as texture and phase evolution in the processed alloys. Currently, the texture evolution in fusion-based AM (F-BAM) processes is majorly rationalized by the phenomena occurring only during solidification. However, such rationalization is insufficient for understanding the evolution of primary and secondary crystallographic orientations, and consequently, fails to offer a comprehensive understanding and control of overall texture in F-BAM processed alloys. To this end, we report a single crystal (SX)-like texture in WA-DED processed SS316L for the first time. Furthermore, we assess the physical phenomena that may lead to such unique microstructural evolution during WA-DED AM. Subsequently, using microstructural characterization spanning the build height and thermomechanical simulations we investigate the effect of competitive growth and epitaxial growth occurring during solidification and thermally induced plastic deformation occurring post solidification on the overall texture of WA-DED processed SS316L. A spatial variation in solidification pathway is also established and correlated with variation in undercoolings across the build. Tensile tests revealed a strong orientation dependence of deformation mechanisms with over 110% elongation to failure of specimens deformed along <011>. Such anisotropy is rationalized using Schmid's analysis of dislocation slip and deformation twinning. Importantly, overall, the mechanisms outlined in this work will facilitate an enhanced understanding and subsequent control of texture evolution, solidification behavior and mechanical behavior of WA-DED processed steels.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure, stored energy, and stability of H/He-filled nanocavities in low temperature irradiated Inconel 718

The microstructure, trapped transmutation gases, stored energy, and mechanical behavior of samples from an irradiated Inconel 718 proton beam window were characterized using transmission electron microcopy, thermal desorption spectrometry (TDS), differential scanning calorimetry (DSC), and tensile testing. In the as-irradiated condition the microstructure contained a high number density of 1–3 nm gas-filled nanocavities. Emissions of trapped gases, H and He, during TDS correlated with peaks of the energy release curves from DSC examinations, which suggest these gases were likely stored in highly stable defect traps. The stored energy from radiation damage saturated at doses of a few dpa and did not increase with increasing radiation dose, but the amount of stored H and He increased with increasing dose. Effects of post-irradiation annealing were studied as well. After exposure to 700 °C, the nanocavities grew only slightly to 2–4 nm in diameter, but after exposure to 900 °C, the cavities grew to 10–20 nm in diameter and electron energy-loss spectroscopy showed these cavities contained a core of He surrounded by a shell of H. Further, this study demonstrated that the irradiation defect structures containing H and He were remarkably stable during irradiation and after exposure up to 700 °C. The effect of the irradiation temperature, defect mobility, and interaction of H, He, and irradiation defects on mechanical behavior provides insight into the processes responsible for the unusual recovery in ductility with increasing radiation dose observed in Inconel 718 after high energy proton and spallation neutron irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A novel microstructural approach for TRIP/TWIP β-Ti alloys using intermetallic precipitation

Interest in metastable β-Ti has grown, due to the exceptional work hardening caused by TRansformation and TWinning Induced Plasticity (TRIP/TWIP). A current challenge is increasing the yield strength, while maintaining the benefits of TRIP/TWIP. This study presents the first report of TRIP/TWIP in a metastable β-Ti alloy containing intermetallic compounds, specifically Ti silicide precipitates. Silicon (Si) additions enable the formation of silicide particles, which can be precipitated, dissolved, and controlled through tailored heat treatments. In-situ synchrotron x-ray diffraction during tensile testing reveals primary {332}<113> twinning activates first, followed by TRIP, leading to extensive work hardening and uniform elongation in the solutionized state. In conclusion, these findings open a novel microstructural approach to the design of multiphase TRIP/TWIP titanium alloys, relying on intermetallic precipitation rather than allotropes such as α or ω phase, and lay the groundwork for future studies on intermetallic precipitation strengthening.

Materials science↗
DOE OSTI2025

Effects of magnetic field assisted heat treatment on the microstructure and mechanical properties of Fe-0.63 %C alloy

This study investigates the influence of an applied magnetic field on the microstructural evolution and mechanical properties of hypoeutectoid steels subjected to heat treatment. Tensile tests and microstructural analysis were performed on samples processed under varying magnetic field strengths (0 T, 5 T, and 9 T) and different austenitization incubation times. The results indicate that the application of a magnetic field alters the fraction of proeutectoid ferrite phase without changing the cooling rates and heat treatment process. Additionally, pearlite microstructural features such as lamellar spacing and misorientation angles exhibit variations under different field strengths. While the pearlite nodule diameter remains largely unaffected, an increase in percentage elongation and strength is observed in the 5 T treated sample, attributed to changes in microstructural features with the magnetic field. Additionally, the percentage elongation is reduced in the samples heat treated with reduced austenitization incubation times. The study further demonstrates that low-angle misorientations increased in the samples taken parallel to the magnetic field direction, influencing the mechanical response. These findings suggest that applying a magnetic field during heat treatment provides an additional driving force for phase transformations, offering a manufacturing process for tailoring microstructures and optimizing mechanical properties. Moreover, integrating magnetic fields in heat treatment processes has potential benefits in energy efficiency.

High magnetic field↗
DOE OSTI2021

Developing an experimental-computational framework to investigate the deformation mechanisms and mechanical properties of Al-8Ce-10Mg alloys at micro and macroscales

There is a promising future for the use of aluminum-cerium-magnesium alloys in a broad range of applications, including devices that operate at high temperatures. With cerium currently considered a waste product of rare earth mining validation studies of possible applications are essential to reduce the environmental waste. Here, a computational-experimental framework is developed to investigate the role both the intermetallic and matrix have on the mechanical properties of these alloys. A set of experiments, including SEM/EBSD imaging, nanoindentation, in-situ SEM tensile testing, and in-situ SEM-DIC tests are performed to characterize the microstructure and mechanical properties of these alloys. Furthermore, the elastic, plastic, and failure deformation mechanisms of the microstructure, and their correlation with the bulk scale mechanical properties are investigated. Experimental results are also used to calibrate parameters for a crystal plasticity finite element model, by performing a computational framework that minimizes the error between the computational and experimental results. This model is then utilized to investigate how the area percentage of intermetallics and the crystallographic texture control the mechanical properties of the alloy. Simulation results show that an increase in the percentage of intermetallics increase the strength but decrease the ductility of the alloy. Also, a change in material texture improves strength and reduces damage that leads to material failure. The development of the crystal plasticity model, as discussed in this work, opens opportunities for future investigations of similar aluminum-cerium-magnesium alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Synthesis and thermomechanical characteristics of zwitterionic poly(arylene ether sulfone) copolymers

Charge-containing polymeric materials have been widely studied for a range of applications. The fundamental relationships between the charge species, charge density, and the microscale morphology of charge-containing polymers are critical for defining the application in which they may be used. In this work, a series of thermoplastic poly(arylene ether sulfone) (PAES) copolymers with controllable sulfobetaine charge contents (0~100 mol%) and high molecular weights (Mw ~ 65 kDa) were prepared. All the zwitterionic PAESs synthesized showed thermal stability up to 250 °C. DSC and tensile tests showed a decreased T g and mechanical strength with the incorporation of increasing charge density, which suggests a plasticization effect by the charged group. Electron microscopy and X-ray scattering data confirmed the absence of microphase separation in the ion-containing random copolymer system, which corroborated with the observation of a single T g for all zwitterionic copolymers studied. Furthermore, the relative hydrophilicity of the samples was evaluated by water uptake measurements, which revealed that the water uptake of the zwitterionic PAESs can reach up to 64% for the 72 mol% zwitterion copolymer while the free-standing film in the wet state still maintains a Young's modulus of 185 MPa. Here, the thermoplastic charge-containing copolymers in this work demonstrated potential for applications such as coatings or water purification membranes, in which balancing hydrophilicity, processibility, and thermomechanical performance are important.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Evaluating the Taylor hardening model in polycrystalline Ti using high energy X-ray diffraction microscopy

High energy X-ray diffraction microscopy (HEDM) was employed to index nearly 1000 grains in a polycrystalline Ti specimen and characterize their deformation during an incremental tensile test. For each grain, the positions of its associated diffraction peaks were used for analyzing its evolving crystal orientation and stress tensor. The azimuthal breadth of each peak at different load steps was measured, allowing measurement of initial yielding and providing an estimate of the dislocation density evolution in each grain. Furthermore, the Taylor hardening model was evaluated grain by grain using the above data, indicating that it can represent hardening in most grains. The yield stress and the strain hardening coefficient for all grains were statistically analyzed with respect to grain orientation, grain size, slip systems, and the surrounding neighborhood to examine how the yield stress and hardening are correlated.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Experimental determination of critical resolved shear stress for strain-induced phase transformation

The current investigation reports the first attempt to measure the critical resolved shear stress to initiates strain-induced phase transformation in a three-dimensional polycrystalline aggregate using high-energy diffraction microscopy (HEDM). In situ tensile testing was performed on a Fe38.5Mn20Co20Cr15Si5Cu1.5 metastable alloy exhibiting transformation-induced plasticity (TRIP). Grains with a higher propensity for strain-induced phase transformation were tracked using HEDM. A sharp drop in grain specific stress, coinciding with the appearance of a new ε-hcp grain oriented relative to the parent γ-fcc phase, was taken as evidence of grain-specific stress required to trigger phase transformation. The highest resolved shear stress on the potential transformation systems was identified as the critical resolved shear stress (CRSS) for strain-induced phase transformation. For the studied metastable alloy, CRSS for transformation was determined to be 86±3 MPa which was very close to theoretical CRSS value determined using Schmid factor (89±12 MPa) compared to the value determined using Taylor factor (62±7 MPa).

Jain, Roopam↗
DOE OSTI2023

Well-Tunable, 3D-printable, and Fast Autonomous Self-Healing Elastomers

Self-healing elastomers provide extended longevity of functional materials, due to their unique adaptability and durability. However, a major scientific challenge remains in developing materials with a rapid healing process combined with decent mechanical properties, that can be prepared by a relatively simple synthesis approach. Herein, we report a versatile design approach on self-healing elastomers by incorporating two different hydrogen bonding containing monomers, i.e., 2-[[(butylamino)carbonyl]oxy]ethyl acrylate (BCOE) and 2-ureido-4[1H]pyrimidinone (UPy) functionalized ethyl methacrylate. Poly(BCOE-r-UPy)s are synthesized by reversible addition-fragmentation chain-transfer (RAFT) polymerization, and controlling the ratio of two monomers enables well-tunable mechanical properties with tensile strength ranging from 0.04 to 6.3 MPa and tensile strain up to 3,000 %. The characteristic dissociation energy is calculated from a temperature dependence of terminal relaxation followed by subtracting the segmental relaxation. The rapid autonomous self-healing is achieved when the molar composition of Poly(BCOE-r-UPy) is tailored to BCOE/UPy = 99/1. The self-healing process is monitored in situ by a helium-ion microscope, and its macroscopic study using tensile tests indicates that Poly(BCOE-r-UPy1) with 1 % molar ratio of UPy recovers 70 % of its original toughness at ambient temperature within 10 mins. 3D printing of Poly(BCOE-r-UPy) affords a self-healable 3D structure, demonstrating the adaptability of Poly(BCOE-r-UPy) for on-demand fabrication. The simplicity of synthesis, well-tunable mechanical properties, unique self-healability, and 3D printing capability of Poly(BCOE-r-UPy)s indicate their potential for a range of applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Analysis of the Amorphous and Interphase Influence of Comononomer Loading on Polymer Properties toward Forwarding Bioadvantaged Copolyamides

In this paper we present an approach for selectively modifying the properties of semicrystalline polymers by introducing “bioadvantaged” counits. With this approach, the unique functionality of biomass can be leveraged to tailor the properties of the amorphous phase of semicrystalline polymers with minimal impact on crystallinity and thermomechanical properties. As a model case, PA 6,6 copolyamides were produced using the bioadvantaged monomer trans-3-hexenedioic acid (t3HDA). The analogous structure of t3HDA to adipic acid, a PA 6,6 monomer, allows for seamless integration. Screening over the entire composition range identified the t3HDA loading (20 mol%) beyond which properties deviate appreciably from Nylon 6,6. Once identified, copolyamides of suitable compositions were upgraded to commercial quality and fully characterized to assess the influence of counit loading and polymer structure on thermal and mechanical properties. Samples were characterized using gel permeation chromatography (GPC), proton nuclear magnetic resonance spectroscopy (1H NMR), heteronuclear single quantum coherence spectroscopy (HSQC), wide-angle X-ray scattering (WAXS), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), tensile testing, flexural testing, and water absorption testing. t3HDA units were shown to hydrate during the harsh polycondensation to 3-hydroxyhexanedioic acid (3HHDA) and fully incorporate into the polymer backbone. Loading levels up to 20% were shown to have comparable thermal and mechanical properties in the dry state, yet moisture absorption—a known method for improving the toughness, yield strain, and elongation of polyamides—was enhanced by over 100% at 20% loading. This case study on bioadvantaged copolymers elucidates the governing structure-function principles that can be leveraged to forward value-added renewable polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Improved Polypropylene Thermoformability through Polyethylene Layering

Due to its low cost, stiffness, and recyclability, isotactic polypropylene (iPP) is an excellent candidate for packaging applications. However, iPP is notoriously difficult to thermoform due to its low melt strength. The addition of just 10 thin layers of high-molecular-weight, linear low-density polyethylene (LLDPE) into iPP sheets by coextrusion significantly increased extensional viscosity and reduced sag. Both LLDPE and iPP were metallocene-catalyzed with excellent adhesion as measured in our previous work. Here, we performed a series of hot tensile tests and sheet sag measurements to determine the properties of the iPP sheet and the multilayer sheet between 130 and 180 °C. To evaluate the thermoformability of these multilayer sheets, truncated conical cups were positive vacuum formed at different temperatures and heating times, and the crush strength was measured. Cups that released easily from the mold with good shape retention and a crush strength within 80% of the maximum value were used to define a temperature–time thermoformability window. We estimated the maximum stress that occurred during the thermoforming process to be 5 MPa. Layer thicknesses before and after thermoforming were used to estimate an average strain of 0.78. The thin LLDPE layers decreased the yield stress below 5 MPa. This enabled thermoforming at sheet temperatures as low as 150 °C. The immiscible LLDPE interfaces increased extensional viscosity, which decreased sag in the multilayer sheets compared to iPP. This broadened the thermoforming range to temperatures as high as 180 °C and allowed longer heating times. These highly thermoformable, layered sheets may be recycled as iPP since they contain only 8% of LLDPE.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Fluoropolymer Composites from Partially Perfluoroalkylated Waste Polyethylene

Chemically modified plastics have emerged as practical solutions to plastic waste increases. Here, the inherent novelty of decorating polymer chains with chemical functionality results in distinct properties that expand the available application space. Nevertheless, developing designer materials for specific applications beyond compatibilization or mild property enhancement is difficult due to the synergistic effects of both the polar functionality imparted and the parent materials' intrinsic properties. By incorporating perfluoro-alkyl side-chains onto the backbone of dehydrogenated waste HDPE, unique surface properties intermediate between polytetrafluoroethylene (PTFE, the model fluoropolymer) and HDPE become apparent, while the overall material mechanical and thermal properties result in more LLDPE-like materials. This is demonstrated through moderate decreases in the surface free energy of the perfluoroalkylated polyolefin surface (increase in H 2 O contact angle of ~ 6°) and increased ordering under shear when blended with PTFE nanoparticles where the crossover point occurred at higher strains. Critically, perfluoroalkylated HDPE possesses improved rheological modification properties at elevated temperatures with PTFE nanoparticles, resulting in more thermally robust and stable composite materials.

fluoropolymer↗
DOE OSTI2026

Ultrasonic-Assisted Extrusion Processing for Enhancing Physical Properties of High-Density Polyethylene by Flow-Induced Crystallization

The evolution of crystallinity resulting from stress imposed on a melt, known as flow-induced crystallinity, can strongly influence the mechanical and physical properties of semicrystalline polymers. This study investigates shear-induced crystallization by applying an ultrasonic field to the melt flow as it passes through dies with various geometries. A custom-built sonication die is employed for controlling the dynamic temperature and shear environment, resulting in molecular alignment and potential for flow-induced crystallization. Application of both conventional and ultrasonic shear rates at the equilibrium melt temperature of high-density polyethylene (HDPE) was investigated to accelerate crystallinity and manipulate the crystal morphology across the film in pursuit of improved mechanical and gas barrier properties without the need for additives or other polymer layers. The relationships among ultrasonic-assisted extrusion processing, polymer structure, and performance were analyzed using wide- and small-angle X-ray scattering (WAXS and SAXS), tensile testing, and oxygen transmission rate (OTR) analysis. Multiple linear regression models were implemented to predict the correlation among HDPE structure, process, and properties. Structural analysis revealed that both conventional and ultrasonic shear rates had the most significant influence on lamellar spacing and redistribution of rigid and soft amorphous fractions within the crystalline domains, ultimately dictating the mechanical and physical properties of the films. The goal is to explore the potential of the ultrasonic-assisted high crystallinity monolayer that can replace some of the functionality of complex, heterogeneous multilayer packaging with a single-material film having enhanced oxygen barrier properties.

crystallinity↗