SEARCH · Engineering Papers

Results for “Strain mapping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Reducing the Strain Required for Ambient‐Pressure Superconductivity in Ruddlesden‐Popper Bilayer Nickelates

ABSTRACT The discovery of high‐temperature superconductivity in pressurized bulk Ruddlesden‐Popper (RP) bilayer nickelates has prompted the conjecture that epitaxial compressive strain might mimic essential aspects of hydrostatic pressure. The realization of superconductivity in films on SrLaAlO 4 (001) (SLAO) supports this correspondence, yet it remains unclear whether the pressure–temperature phase diagram of RP bilayer nickelates can be systematically mapped (and studied at ambient pressure) as a function of epitaxial strain. To this end, experimental access near the elusive edge of the superconducting phase boundary would provide invaluable insight into the nature of the superconducting state and the ground state from which it emerges. Here we report superconducting RP bilayer nickelates grown on LaAlO 3 (001) (LAO), where the compressive strain required for ambient‐pressure superconductivity is nearly halved to −1.2%. These films exhibit a superconducting onset above 10 K and reach zero resistance at 3 K, with normal‐state transport properties differing from those of films grown on SLAO. Our comparative study shows that strain–rather than interfacial structure is the primary factor governing the superconductivity and normal‐state properties. This work offers a new opportunity to probe emergent phenomena near the superconducting phase boundary in the strain–temperature phase diagram of RP bilayer nickelates.

Tarn, Yaoju [Department of Applied Physics Stanfor↗

DOE OSTI2019

Study on Tensile Deformation Behavior of TC21 Titanium Alloy

To investigate the tensile deformation behavior of TC21 titanium alloy wires, the isothermal tensile deformation tests were conducted by a Geeble-1500D simulator in the temperature range of 720-880 °C and strain rates of 0.01-10 s{sup −1}. The in situ tensile deformation behavior has been studied by SEM SURPA40. The stress–strain curves indicate that the flow stress has shown an inverse relationship with temperature and a direct relationship with strain rate. The flow stress immediately reached the peak value and, then, gradually decreased due to the dynamic softening induced by dynamic recovery and dynamic recrystallization. According to the hot processing maps, the temperatures ranging from 720 to 760 °C (corresponding to the strain rates of 0.01-0.032 s{sup −1}) and 800-840 °C (corresponding to the strain rates of 0.01-0.056 s{sup −1}) are suitable for processing. The in situ tensile results reveal that the cracks initiated at the pre-fabricated defects with the concentrated stress and mainly propagated in the transgranular mode.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Towards data-driven constitutive modelling for granular materials via micromechanics-informed deep learning

The analytical description of path-dependent elastic-plastic responses of a granular system is highly complicated because of continuously evolving microstructures and strain localisation within the system undergoing deformation. This study offers an alternative to the current analytical paradigm by developing micromechanics-informed machine-learning based constitutive modelling approaches for granular materials. A set of critical variables associated with the constitutive behaviour of granular materials are identified through an incremental stress-strain relationship analysis. Depending on the strategy to exploit the priori micromechanical knowledge, three different training strategies are explored. The first model uses only the measurable external variables to make stress predictions; the second model utilises a directed graph to link all the external strain sequences and internal microstructural evolution variables into a single prediction model comprised of a series of sub-mappings, and the third model explicitly integrates the physically important non-temporal properties with external strain paths into training through an enhanced Gated Recurrent Unit (GRU). These three models show satisfactory agreement with unseen test specimens based on multi-directional loading cases. The basic features and potential applications of each model are explained. Lastly, the key factors for constitutive training and limitations of the current work are also discussed in detail.

36 MATERIALS SCIENCE↗

DOE OSTI2018

Study on hot deformation behavior and workability of squeeze-cast 20 vol%SiCw/6061Al composites using processing map

Highlights: • Prasad’s and Murty’s criteria were better than Gegel’s criterion in predicting the flow instability for the composites. • Partial melting and DRX at high temperature and high strain rate improved the workability of the composites. • The softening mechanism changed from DRV to DRX with the increase of deformation temperature and strain rate. • The safe deformation region of the composites was at higher temperature of 450-500°C and higher strain rate of 0.1-1s{sup -1}. • The safe deformation region predicted by processing maps was validated by uniaxial upsetting and two-directional forging. - Abstract: The hot deformation behavior and workability of squeeze-cast 20 vol%SiCw/6061Al composites were investigated by isothermal compression test and development of processing map, which was verified by uniaxial upsetting and two-directional forging of big cylindrical billets. Due to dispersed strengthening caused by SiC whiskers, the activation energy of 20 vol%SiCw/6061Al composites was much higher than the self-diffusion activation energy of pure Al. Both the DMM and MDMM were reliable in predicting the safe deformation regions. The instability regions predicted by the Prasad's and Murty's instability criterion were smaller than the actual ones, while the Gegel's instability criterion was not appropriate in predicting the instability regions of 20 vol%SiCw/6061Al composites. The optimum deformation region was at higher temperature of 450–500 °C and higher strain rate of 0.1–1 s{sup − 1}, in which the compressed samples exhibited perfect surface without cracks and microstructure with few of cavities due to the occurrence of partial melting and dynamic recrystallization. With the increase of deformation temperature and strain rate, the deformation mechanism changed from dynamic recovery to dynamic recrystallization. Squeezing casting technique with high filtration pressure may also contribute to the increase of strain rate of DRX, which was helpful for hot forging of Al matrix composites with high productivity.

36 MATERIALS SCIENCE↗

NASA NTRS2005

Salt Kinematics and InSAR

As part of a long-term attempt to learn how the climatic and tectonic signal interact to shape a steady state mountain monitored displacement of a markers in SE termination and also near the summit of a small viscous salt fountain extruding onto the Central plateau of Iran. The marker displacements relate to the first InSAR interferograms of salt extrusion (980913 to 990620) calculated Earth tides, winds, air pressures and temperatures. In the first documented staking exercise, hammered wooden stakes vertically through the surgical marl (c. 1 Ocm deep) onto the top of crystalline salt. These stakes installed in an irregular array elongate E-W along the c.50 m high cliff marking the effective SE terminus of the glacier at Qum Kuh(Centra1 Iran) ,just to the E of a NE trending river cliff about 40 m high. We merely measured the distances between pairs of stakes with known azimuth about 2 m apart to calculate sub horizontal strain in a small part of Qum Kuh. Stakes moved and micro strains for up to 46 pairs of stakes (p strain= ((lengthl-length2)/1engthl) x 10-1) was calculated for each seven stake epochs and plotted against their azimuth on simplified array maps. The data fit well the sine curves cxpected of the maximum and minimum strain ellipses. The first documented stakes located on the SE where the InSAR image show -1 1 to 0 mm pink to purple, 0 to lOmm purple to blue, and show high activity of salt in low activity area of the InSAR image (980913 to 990620).Short term micro strains of stake tie lines record anisotropic expansions due to heating and contraction due to cooling. All epochs changed between 7 to 1 17 days (990928 to000 1 16), showed 200 to 400 micro strain lengthening and shortening. The contraction and extension existed in each epoch, but the final strain was extension in E-W in Epoch land 6, contraction in E-W direction during epochs 2-3-4-5 and 7. The second pair of stakes hammered about 20 cm deep into the deep soils(more than 1 m) , near summit, where the colors change between 19 to 29mm in InSAR image(9809 13 to 990620). Additional information is included in the original abstract.

Aftabi, Pedarm↗

DOE OSTI2018

Non-Destructive Measurement of Residual Strain in Connecting Rods Using Neutrons

Increasing the strength of materials is effective in reducing weight and boosting structural part performance, but there are cases in where the residual strain generated during the process of manufacturing of high-strength materials results in a decline of durability. It is therefore important to understand how the residual strain in a manufactured component changes due to processing conditions. In the case of a connecting rod, because the strain load on the connecting rod rib sections is high, it is necessary to clearly understand the distribution of strain in the ribs. However, because residual strain is generally measured by using X-ray diffractometers or strain gauges, measurements are limited to the surface layer of the parts. Neutron beams, however, have a higher penetration depth than X-rays, allowing for strain measurement in the bulk material. The research discussed within this paper consists of non-destructive residual strain measurements in the interior of connecting rods using the 2nd Generation Neutron Residual Stress Mapping Facility (NRSF2) at Oak Ridge National Laboratory, measuring the Fe (211) diffraction peak position of the ferrite phase. The interior strain distribution of connecting rod, which prepared under different manufacturing processes, was revealed. By the visualization of interior strains, clear understandings of differences in various processing conditions were obtained. In addition, it is known that the peak width, which is also obtained during measurement, is suggestive of the size of crystallites in the structure; however the peak width can additionally be caused by microstresses and material dislocations.

Ikeda, Tomohiro↗

DOE OSTI2021

In-situ synchrotron X-ray micro-diffraction investigation of ultra-low-strain deformation microstructure in laminated Ti-Al composites

An ultra-low-strain deformation microstructure was revealed for the first time non-destructively in the bulk interior of an annealed laminated Ti-Al composite-in the "fully recrystallized" Al layer-by a synchrotron-based micro-diffraction technique, namely differential aperture X-ray microscopy (DAXM), through real space mapping with a very high angular resolution (0.01 degrees). This ultra-low-strain deformation microstructure was found to result from the thermal stress, induced during cooling after annealing, due to the different coefficients of thermal expansion for the Ti and Al layers. The annealed sample was further tensile deformed to a strain of 1.66% and followed by in situ DAXM and analyzed by various misorientation mapping methods. The results pointed to the important effects of the initial microstructure and the interface constraint, as well as the grain size and crystal orientation, on the plastic deformation. A gradient in dislocation density from the layer interface to the center was found in the Al layer of the annealed sample, and this gradient increased slightly during tensile deformation. The variation of the dislocation density was further discussed based on the activation and interaction of dislocations in grains of different sizes and orientations during plastic deformation. The findings of this study provided valuable insights in understanding the constraint effect of the laminated metal composite and the design of novel composite materials. (c) 2020 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Crystallographic orientation↗

NASA NTRS2001

Laboratory multiple-crystal X-ray topography and reciprocal-space mapping of protein crystals: influence of impurities on crystal perfection

Double-axis multiple-crystal X-ray topography, rocking-curve measurements and triple-axis reciprocal-space mapping have been combined to characterize protein crystals using a laboratory source. Crystals of lysozyme and lysozyme crystals doped with acetylated lysozyme impurities were examined. It was shown that the incorporation of acetylated lysozyme into crystals of lysozyme induces mosaic domains that are responsible for the broadening and/or splitting of rocking curves and diffraction-space maps along the direction normal to the reciprocal-lattice vector, while the overall elastic lattice strain of the impurity-doped crystals does not appear to be appreciable in high angular resolution reciprocal-space maps. Multiple-crystal monochromatic X-ray topography, which is highly sensitive to lattice distortions, was used to reveal the spatial distribution of mosaic domains in crystals which correlates with the diffraction features in reciprocal space. Discussions of the influence of acetylated lysozyme on crystal perfection are given in terms of our observations.

Muramidase/chemistry↗

DOE OSTI2015

Nanoscale mapping of electromechanical response in ionic conductive ceramics with piezoelectric inclusions

Electromechanical (EM) response in ion conductive ceramics with piezoelectric inclusions was spatially explored using strain-based atomic force microscopy. Since the sample is composed of two dominant phases of ionic and piezoelectric phases, it allows us to explore two different EM responses of electrically induced ionic response and piezoresponse over the same surface. Furthermore, EM response of the ionic phase, i.e., electrochemical strain, was quantitatively investigated from the comparison with that of the piezoelectric phase, i.e., piezoresponse. These results could provide additional information on the EM properties, including the electrochemical strain at nanoscale.

36 MATERIALS SCIENCE↗

DOE OSTI2016

Investigation of deformation twinning under complex stress states in a rolled magnesium alloy

We employed a specially designed semi-circular notch specimen in the current study to generate the various strain conditions, including uniaxial, biaxial, shear, and plane strains, which was utilized to explore the evolution of different deformation twinning systems under complex loading conditions. We found that when using in situ synchrotron X-ray diffraction mapping method, that the extensive double twins were activated during loading, while nearly no extension twinning activity was detected. After the formation of {10.1} and {10.3} compression twins, they transformed into {10.1}-{10.2} and {10.3}-{10.2} double twins instantaneously at the early stage of deformation. The lattice strain evolutions in different hkls were mapped at selected load levels during the loading-unloading sequence. Finally, the relationship between the macroscopic straining and microscopic response was established.

36 MATERIALS SCIENCE↗

DOE OSTI2019

Nondestructive Measurement of Residual Strain in Connecting Rods Using Neutrons

Increasing the strength of materials is effective in reducing weight and boosting structural part performance, but there are cases where the residual strain generated during the process of manufacturing of high-strength materials results in a decline of durability. It is therefore important to understand how the residual strain in a manufactured component changes due to processing conditions. In the case of a connecting rod, because the strain load on the connecting rod rib sections is high, it is necessary to clearly understand the distribution of strain in the ribs. However, because residual strain is generally measured by using X-ray diffractometers or strain gauges, measurements are limited to the surface layer of the parts. Neutron beams, however, have a higher penetration depth than X-rays, allowing for strain measurement in the bulk material. The research discussed within this article consists of nondestructive residual strain measurements in the interior of connecting rods using the Second Generation Neutron Residual Stress Mapping Facility (NRSF2) at Oak Ridge National Laboratory (ORNL), measuring the Fe (211) diffraction peak position of the ferrite phase. The interior strain distribution of the connecting rod, which was prepared under different manufacturing processes, was revealed. By the visualization of interior strains, clear understandings of differences in various processing conditions were obtained. In addition, it is known that the peak width, which is also obtained during measurement, is suggestive of the size of crystallites in the structure; however, the peak width can additionally be caused by microstresses and material dislocations.

36 MATERIALS SCIENCE↗

DOE OSTI2018

Hot-worked microstructure and hot workability of cold-work tool steels

Highlights: • Hot compression tests were conducted for D2 and an 8% Cr steel. • Processing maps were constructed for the evaluation of their hot workability. • They had similar hot workability concerning the flow instability. • The 8% Cr steel exhibited a larger resistance to dynamic recrystallization. - Abstract: The hot workability of two cold-work tool steels were evaluated and compared. A D2 and an advanced alloy based on 8% Cr steels (TDx) were deformed at high temperatures between 900 and 1100 °C with strain rates 0.001–10 s{sup − 1} via hot compression test. From the flow curves, processing maps were constructed based on the dynamic material model. The deformed microstructures were observed and compared in various scales with respect to the deformation conditions. Although the two alloys exhibited a large similarity in the flow instability consideration of the processing map, their behavior in microstructure evolution was different. While both alloys exhibited a tendency of strain localization in the conditions of instability, the efficiency of power dissipation in the processing maps showed an intricate correlation with the progress of dynamic recrystallization and carbide precipitation. TDx showed a distinctive behavior of carbide precipitation and a larger resistance to dynamic recrystallization, which implied a requirement on more delicate control of hot working conditions.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Low-temperature state in strontium titanate microcrystals using in situ multireflection Bragg coherent x-ray diffraction imaging

Strontium titanate is a classic quantum paraelectric oxide material that has been widely studied in bulk and thin films. It exhibits a well-known cubic-to-tetragonal antiferrodistortive phase transition at 105 K, characterized by the rotation of oxygen octahedra. A possible second phase transition at lower temperature is suppressed by quantum fluctuations, preventing the onset of ferroelectric order. However, recent studies have shown that ferroelectric order can be established at low temperatures by inducing strain and other means. Here, we used in situ multireflection Bragg coherent x-ray diffraction imaging to measure the strain and rotation tensors for two strontium titanate microcrystals at low temperature. We observe strains induced by dislocations and inclusion-like impurities in the microcrystals. Based on radial magnitude plots, these strains increase in magnitude and spread as the temperature decreases. Pearson's correlation heat maps show a structural transition at 50 K, which could possibly be the formation of a low-temperature ferroelectric phase in the presence of strain. We do not observe any change in local strains associated with the tetragonal phase transition at 105 K.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2012

Mapping N-linked Glycosylation Sites in the Secretome and Whole Cells of Aspergillus niger Using Hydrazide Chemistry and Mass Spectrometry

Protein glycosylation is known to play an essential role in both cellular functions and the secretory pathways; however, little information is available on the dynamics of glycosylated N-linked glycosites of fungi. Herein we present the first extensive mapping of glycosylated N-linked glycosites in industrial strain Aspergillus niger by applying an optimized solid phase enrichment of glycopeptide protocol using hydrazide modified magnetic beads. The enrichment protocol was initially optimized using mouse plasma and A. niger secretome samples, which was then applied to profile N-linked glycosites from both the secretome and whole cell lysates of A. niger. A total of 847 unique N-linked glycosites and 330 N-linked glycoproteins were confidently identified by LC-MS/MS. Based on gene ontology analysis, the identified N-linked glycoproteins in the whole cell lysate were primarily localized in the plasma membrane, endoplasmic reticulum, golgi apparatus, lysosome, and storage vacuoles. The identified N-linked glycoproteins are involved in a wide range of biological processes including gene regulation and signal transduction, protein folding and assembly, protein modification and carbohydrate metabolism. The extensive coverage of glycosylated N-linked glycosites along with identification of partial N-linked glycosylation in those enzymes involving in different biochemical pathways provide useful information for functional studies of N-linked glycosylation and their biotechnological applications in A. niger.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2016

Mitochondrial protein functions elucidated by multi-omic mass spectrometry profiling

Mitochondrial dysfunction is associated with many human diseases, including cancer and neurodegeneration, that are often linked to proteins and pathways that are not well-characterized. To begin defining the functions of such poorly characterized proteins, we used mass spectrometry to map the proteomes, lipidomes and metabolomes of 174 yeast strains, each lacking a single gene related to mitochondrial biology. 144 of these genes have human homologs, 60 of which are associated with disease and 39 of which are uncharacterized. We present a multi-omic data analysis and visualization tool that we use to find covariance networks that can predict molecular functions, correlations between profiles of related gene deletions, gene-specific perturbations that reflect protein functions, and a global respiration deficiency response. Using this multi-omic approach, we link seven proteins including Hfd1p and its human homolog ALDH3A1 to mitochondrial coenzyme Q (CoQ) biosynthesis, an essential pathway disrupted in many human diseases. This Resource should provide broad molecular insights into mitochondrial protein functions.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2019

High‐quality genome‐scale metabolic modelling of Pseudomonas putida highlights its broad metabolic capabilities

Summary Genome‐scale reconstructions of metabolism are computational species‐specific knowledge bases able to compute systemic metabolic properties. We present a comprehensive and validated reconstruction of the biotechnologically relevant bacterium Pseudomonas putida KT2440 that greatly expands computable predictions of its metabolic states. The reconstruction represents a significant reactome expansion over available reconstructed bacterial metabolic networks. Specifically, i JN1462 (i) incorporates several hundred additional genes and associated reactions resulting in new predictive capabilities, including new nutrients supporting growth; (ii) was validated by in vivo growth screens that included previously untested carbon (48) and nitrogen (41) sources; (iii) yielded gene essentiality predictions showing large accuracy when compared with a knock‐out library and Bar‐seq data; and (iv) allowed mapping of its network to 82 P . putida sequenced strains revealing functional core that reflect the large metabolic versatility of this species, including aromatic compounds derived from lignin. Thus, this study provides a thoroughly updated metabolic reconstruction and new computable phenotypes for P . putida , which can be leveraged as a first step toward understanding the pan metabolic capabilities of Pseudomonas .

Microbiology↗

DOE OSTI2018

Complete Status Report Documenting the Development of Friction Stir Welding for Producing a Butt Joint in Thin Wall Tubing of ODS Alloys

A challenging attempt using friction stir welding to produce a butt joint between two 1.0 mm thick plates of 14YWT was nearly successful. The modified tool pin mostly penetrated the thickness of the adjoined thin plate samples resulting in a small blunt notch on the bottom surface of the butt joint. A bend occurred in the thin plate sample due to formation of stresses from clamping the thin plate sample during FSW. The peak displacement of the bend occurred along the center line of the butt joint. The weld zone showed good microstructure mixing with some flashing mostly on the retreating side that suggested excess heat input by friction between the traveling and spinning tool pin and thin plates of 14YWT. Neutron diffraction experiments were performed on the bent sample of 14YWT to measure the residual stresses in the butt joint on the HB-2B beam line at the Neutron Residual Stress Facility at HFIR. However, the neutron scattering to background noise ratio was very low during data acquisition. Measurements of lattice strains were obtained in the rolling (RD) and normal (ND) directions but not in the extrusion direction (ED) of the thin plate sample. Unfortunately, the quality of the data was not sufficient for determining the residual stresses in the butt joint. From the previous neutron scattering experiments conducted on four hot rolled plates (R1, R2, R3 and R4) of 14YWT, the residual stresses were calculated from lattice strain data and plotted in 2-D color contour maps for ED, RD and ND. The results showed variations in the magnitude and spatial position of residual stresses in the microstructure of the four plates. The magnitude in residual stresses in ED and RD increased gradually with increasing rolling deformation for R1 (50%) to R2 (76%), followed by larger increases in R3 (89%) and R4 (95%). The maximum peaks in residual stresses for R4 was ~710-730 MPa in ED and RD. The residual stresses in ND were below ~300 MPa for each of the 4 rolled plates, with a maximum residual stress in R4 (95%) of ~400 MPa. These results indicated that significant residual stresses representing ~57% of the yield stress of 14YWT (SM13) had accumulated in the 14YWT plate after hot rolling to the 1 mm thickness, which was used in the FSW experiments. The microstructure analysis of the 1.0 mm thick plate of 14YWT containing the butt joint produced by FSW revealed significant changes in the grain structure and texture between the unaffected zone (UZ) of the rolled plate and the butt joint weld. In the UZ, the grains were severely elongated after 95% deformation and mainly possessed the {101} texture component in the ED. Two predominant grain misorientation angles were observed: one consisting of small misorientations of <5º between highly elongated grains and the other consisting of large misorientations of >15º in pockets of small grains that might have formed by dynamic recrystallization processes during rolling of the plate at 1000ºC. The morphology and texture of grains in the heat affected zone (HAZ) were similar to those in UZ, except the grains had coarsened due to excess heat input during FSZ. A population of pores formed and the grains both coarsened and changed to isotropic morphology in the microstructure of the butt joint on both the advancing and retreating sides. The texture of grains in both regions were randomly orientated between the 3 poles {001}, {101} and {111}. The main difference in texture of grains between the advancing side and retreating side was with the misorientation angles of neighboring grains. Most of the grains in the advancing side had misorientation angles of >5º indicating that these grains experienced recrystallization. On the retreating side, areas containing larger grains showed high misorientation angles of >15º compared to areas appearing as bands of grains with misorientation angles of <5º and between 5º-15º. Numerous small pockets of grains with low misorientation angles of <5º were distributed in the microstructure among the grains showing high misorientation angles of >15º. It was determined that the grains associated with low misorientation angles contained sub-grain structures, which was consistent with both recrystallization and recovery mechanisms for grains located on the retreating side of the butt joint. These results demonstrate the complex microstructure that evolves in the microstructure of 14YWT resulting from the input of high temperatures and severe deformations during FSW.

36 MATERIALS SCIENCE↗

DOE OSTI2016

Development of a Multi-physics Capability for Predicting Residual Stress in a GTS Reservoir.

This report documents completion of a Level 2 Milestone on the development of a multi-physics capability to predict the evolving material state through the manufacturing process of a Gas Transfer Systems (GTS) reservoir. We present details on new developments and capability improvements that address the following completion criteria: (i) validation of a microstructure evolution model, including recrystallization and strain aging, (ii) demonstration of the capability to remesh, map and transfer material state (internal state variables) and residual stress from forging to machining to welding processes, and (iii) formal V&V characterization and quantification of uncertainties of material parameters and manufacturing process parameters on residual stress.

36 MATERIALS SCIENCE↗