Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Steady state process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Multi-scale dynamic modeling and validation of radial flow fixed bed contactors for post-combustion CO 2 capture using bench scale and pilot plant data

Here, in this work, a multi-scale model of a radial flow fixed bed contactor packed with a carbon sorbent is developed and validated with laboratory-scale and pilot plant scale dynamic data. For the lab scale system, the model results were compared with low, medium and high gas and sweep flowrates, yielding root mean square error (RMSE) of 0.80, 0.63, 0.96 CO 2 mol%, respectively, for the outlet CO 2 concentration profile considering the entire A-D cycle. For the bed outer temperature profile, maximum RMSE was found to be 5.5 °C considering all flowrates and entire A-D cycles. An experimental campaign was developed and applied to a pilot plant at Technology Center Mongstad (TCM), Norway. Approaches were developed for pre-processing of data including consideration of the effect of gas mixing, measurement delay, and determination of cyclic steady-state conditions. Considering profiles during A-D cycles for all test runs, it was found that the maximum RMSE for pressure drop, temperature for the outer section of the bed, temperature for the middle section of the bed, and outlet CO 2 concentration profile remained less than 1.5 mbar, 3.5 °C, 2.8 °C, and 1.3 CO 2 mol%, respectively. The validated model was used to perform sensitivity studies on several key design operating variables for the adsorption-desorption cycle. It was found that the flow rate and concentration of flue gas have dominant nonlinear effects on the breakthrough time while the desorption time was strongly affected by the sweep gas flowrate for the specific sorbent being evaluated in this study.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

A Rapid Microfluidic Neptunium Extraction Using a Supported Liquid Membrane Module

Extraction of neptunium from acidic matrices is important for its quantification, but its complex redox chemistry can cause variable yields. This study develops a microfluidic redox extraction for rapidly separating neptunium from submilliliter samples, achieving up to 90% process yield in less than 10 min for samples as small as 100 μL, with over 97% steady-state yield achieved after 20 min. It uses a supported liquid membrane module loaded with 30 vol % tributyl phosphate in n-dodecane, which performs forward- and back-extractions in a single, continuous step. Neptunium is first oxidized to +6 for extraction and then reduced during stripping. Bromate was selected as an oxidant over permanganate for its greater compatibility with the organic phase, achieving complete oxidation in under 30 s. Ascorbic acid and hydrogen peroxide were both effective reductants. Finally, the system’s high yield and rapid kinetics make it promising for future separations from complex mixtures.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2022

Using Ensemble Data Assimilation to Estimate Transient Hydrologic Exchange Flow Under Highly Dynamic Flow Conditions

Abstract Quantifying dynamic hydrologic exchange flows (HEFs) within river corridors that experience high‐frequency flow variations caused by dam regulations is important for understanding the biogeochemical processes at the river water and groundwater interfaces. Heat has been widely used as a tracer to infer steady‐state flow velocities through analytical solutions of heat transport defined by the diurnal temperature signals. Under sub‐daily dynamic flow conditions, however, such analytical solutions are not applicable due to the violation of their fundamental assumptions. In this study, we developed a data assimilation‐based approach to estimate the sub‐daily flux under highly dynamic flow conditions using multi‐depth temperature observations at a 5‐min resolution. If the hydraulic gradient is measured, Darcy's law was used to calculate the flux with permeability estimated from temperature responses below the riverbed. Otherwise, flux was estimated directly by assimilating multi‐depth temperature data at 1‐ or 2‐hr time intervals assuming one‐dimensional flow and heat transport governing equation. By comparing estimated fluxes with model‐generated synthetic truth, we demonstrated that both schemes have robust performance in estimating fluxes under highly dynamic flow conditions. This data assimilation‐based flux estimation method was able to capture the vertical sub‐daily fluxes using multi‐depth high‐resolution temperature data alone, even in the presence of multi‐dimensional flow. This approach has been successfully applied to real field temperature data collected at the Hanford site, which experiences highly dynamic HEFs. Our study shows the promise of adopting distributed 1‐D temperature monitoring to capture spatial and temporal exchange dynamics in river corridors at a watershed scale or beyond.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Selected advances in small-angle scattering and applications they serve in manufacturing, energy and climate change

Innovations in small-angle X-ray and neutron scattering (SAXS and SANS) at major X-ray and neutron facilities offer new characterization tools for researching materials phenomena relevant to advanced applications. For SAXS, the new generation of diffraction-limited storage rings, incorporating multi-bend achromat concepts, dramatically decrease electron beam emittance and significantly increase X-ray brilliance over previous third-generation sources. This results in intense X-ray incident beams that are more compact in the horizontal plane, allowing significantly improved spatial resolution, better time resolution, and a new era for coherent-beam SAXS methods such as X-ray photon correlation spectroscopy. Elsewhere, X-ray free-electron laser sources provide extremely bright, fully coherent, X-ray pulses of <100 fs and can support SAXS studies of material processes where entire SAXS data sets are collected in a single pulse train. Meanwhile, SANS at both steady-state reactor and pulsed spallation neutron sources has significantly evolved. Developments in neutron optics and multiple detector carriages now enable data collection in a few minutes for materials characterization over nanometre-to-micrometre scale ranges, opening up real-time studies of multi-scale materials phenomena. SANS at pulsed neutron sources is becoming more integrated with neutron diffraction methods for simultaneous structure characterization of complex materials. In this paper, selected developments are highlighted and some recent state-of-the-art studies discussed, relevant to hard matter applications in advanced manufacturing, energy and climate change.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A pilot study: Auditory steady-state responses (ASSR) can be measured in human fetuses using fetal magnetoencephalography (fMEG)

Auditory steady-state responses (ASSRs) are ongoing evoked brain responses to continuous auditory stimuli that play a role for auditory processing of complex sounds and speech perception. Transient auditory event-related responses (AERRs) have previously been recorded using fetal magnetoencephalography (fMEG) but involve different neurological pathways. Previous studies in children and adults demonstrated that the cortical components of the ASSR are significantly affected by state of consciousness and by maturational changes in neonates and young infants. To our knowledge, this is the first study to investigate ASSRs in human fetuses. 47 fMEG sessions were conducted with 24 healthy pregnant women in three gestational age groups (30–32 weeks, 33–35 weeks and 36–39 weeks). The stimulation consisted of amplitude-modulated (AM) tones with a duration of one second, a carrier frequency (CF) of 500 Hz and a modulation frequency (MF) of 27 Hz or 42 Hz. Both tones were presented in a random order with equal probability adding up to 80–100 repetitions per tone. The ASSR across trials was quantified by assessing phase synchrony in the cortical signals at the stimulation frequency. Ten out of 47 recordings were excluded due to technical problems or maternal movements. Analysis of the included 37 fetal recordings revealed a statistically significant response for the phase coherence between trials for the MF of 27 Hz but not for 42 Hz. An exploratory subgroup analysis moreover suggested an advantage in detectability for fetal behavioral state 2F (active asleep) compared to 1F (quiet asleep) detected using fetal heart rate. In conclusion, this pilot study is the first description of a method to detect human ASSRs in fetuses. The findings warrant further investigations of the developing fetal brain.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Towards a NEAMS-based high-fidelity model of the MARVEL reactor

This report outlines the progress of Idaho National Laboratory in developing a high-fidelity and high-resolution model of the Microreactor Applications Research Validation and Evaluation reactor. The model was developed under the Nuclear Energy Advanced Modeling and Simulation microreactor application driver at Idaho National Laboratory. The overarching objective of this activity is the development of a high-fidelity multiphysics MARVEL model using NEAMS tools, and to verify and validate NEAMS tools against MARVEL reference simulation and experimental data, respectively. This is a unique opportunity to conduct multiphysics analysis on a soon-to-be-deployed microreactor. This multiphysics model developed under the NEAMS-funded INL microreactor application driver leverages three single-physics models coupled via the MOOSE’s MultiApp and Transfer systems. The latter systems enable in-memory data transfer between MOOSE-based and MOOSE-wrapped applications. The first single-physics model, that functions as main application, leverages Griffin to model the neutron transport in the core through the discontinuous finite element (DFEM) discrete ordinates solver (SN). Several optimization flags that were developed by the Griffin developer team were beta-tested to enhance the solver’s performance. These include the combined use of using_average_xs and update_averaged_xs_on that enable to avoid expensive on-the-fly cross sections evaluations at each linear iterations in favor of evaluations of the macroscopic cross sections at each Picard iteration. The second single-physics model uses BISON to handle solid heat transfer and asymptotic hydrogen redistribution analysis in the fuel. While the model returns consistent results for the temperature and hydrogen distribution in the fuel, a mismatch was noticed in the calculated temperature in the reflector due to the value of the gap conductance used in our model. Ongoing investigations are being performed to assess the origin of this discrepancy. Finally, the System Analysis Module (SAM) was used to model the flow of the sodium-potassium eutectic in the primary loop. A first verification was also performed showing good agreement in terms of mass flow rate and inlet temperature. All mesh files were generated using the MOOSE Reactor module, removing the need for external meshing tools. Notably, this workscope represents one of the initial applications of the MOOSE Reactor module for modeling highly irregular geometries. The use of the reactor module significantly streamlined the mesh generation process. The full multiphysics mode, that combines all the single physics models, was leveraged to conduct initial steady-state multiphysics simulations to compute power, and temperature distribution in the reactor. Initial testing was performed for transient simulations as well. In this case, the new checkpoint restart capability for eigenvalue calculations was tested showing the capability for streamlined restart of transient calculations. Future work will focus on improving the fidelity of the model by performing comprehensive code-to-code comparisons. For instance, the full-core Griffin neutronics model will be benchmarked against MCNP reference results, that were provided by the MARVEL design team. Additionally, the SAM T/H model will be verified against reference RELAP-5 results for selected accident scenarios. Besides code-to-code verification exercises, the model fidelity will be improved by replacing the single-channel SAM model with a more complex SAM-Pronghorn coupled model, in which the sub-channel capability is deployed to obtain radial temperature resolution in the coolant. This model will be developed in synergy with the NEAMS thermal hydraulics team.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1973

Optical damage and internal fields in pyroelectrics.

The physical conditions under which the models of optical damage in pyroelectrics suggested by Johnston (1970) and by Amodei (1971) might be valid are described. Whether the zero-internal-field final state described by Johnston or the no-current-flow steady state of Amodei can be reached depends on the pattern of excitation and the dynamics of the damage process. In view of the small carrier diffusion lengths, the one-dimensional models generally used may not be entirely satisfactory for investigation of dynamics.

Wood, V. E.↗
NASA NTRS1984

Effects of External Loads on Human Head Movement Control Systems

The central and reflexive control strategies underlying movements were elucidated by studying the effects of external loads on human head movement control systems. Some experimental results are presented on dynamic changes weigh the addition of aviation helmet (SPH4) and lead weights (6 kg). Intended time-optimal movements, their dynamics and electromyographic activity of neck muscles in normal movements, and also in movements made with external weights applied to the head were measured. It was observed that, when the external loads were added, the subject went through complex adapting processes and the head movement trajectory and its derivatives reached steady conditions only after transient adapting period. The steady adapted state was reached after 15 to 20 seconds (i.e., 5 to 6 movements).

Nam, M. H.↗
NASA NTRS1985

Spectral Units on Europa and Ganymede

Comparisons of Europa and Ganymede multispectral data show that Ganymede is less spectrally variable than Europa. Four major spectral units dominate Ganymede, corresponding to the ancient cratered terrain and the grooved terrain in the leading and trailing hemispheres. A hemispheric asymmetry in UV absorption definitely exists on Ganymede, although it is not so strong as that on Europa. Comparison of normalized spectra for the four major units shows that the sense of the asymmetry (more absoption toward shorter wavelengths on the trailing hemisphere) is also the same on the two bodies. This hemispheric asymmetry is interpreted as evidence of alteration of the surface by magnetospheric bombardment or micrometorite bombardment. It is concluded that the pattern observed represents a steady state involving both of these exogenic modifying agents. The spectral changes which could be produced by these two processes are grain size alteration and changes in composition. The spectral effects of variation in water ice grain size are fairly well known. Laboratory experiments are being conducted to study the spectral effects of sulfur irradiation on water ice.

Mccord, T. B.↗
NASA NTRS1986

Simulating a small turboshaft engine in real-time multiprocessor simulator (RTMPS) environment

A Real-Time Multiprocessor Simulator (RTMPS) has been developed at NASA Lewis Research Center. The RTMPS uses parallel microprocessors to achieve computing speeds needed for real-time engine simulation. This report describes the use of the RTMPS system to simulate a small turboshaft engine. The process of programming the engine equations and distributing them over one, two, and four processors is discussed. Steady-state and transient results from the RTMPS simulation are compared with results from a main-frame-based simulation. Processor execution times and the associated execution time savings for the two and four processor cases are presented using actual data obtained from the RTMPS system. Included is a discussion of why the minimum achievable calculation time for the turboshaft engine model was attained using four processors. Finally, future enhancements to the RTMPS system are discussed including the development of a generalized partitioning algorithm to automatically distribute the system equations among the processors in optimum fashion.

Milner, E. J.↗
NASA NTRS1996

Spatial orientation perception and reflexive eye movements--a perspective, an overview, and some clinical implications

When head motion includes a linear velocity component, eye velocity required to track an earth-fixed target depends upon: a) angular and linear head velocity, b) target distance, and c) direction of gaze relative to the motion trajectory. Recent research indicates that eye movements (LVOR), presumably otolith-mediated, partially compensate for linear velocity in small head excursions on small devices. Canal-mediated eye velocity (AVOR), otolith-mediated eye velocity (LVOR), and Ocular Torsion (OT) can be measured, one by one, on small devices. However, response dynamics that depend upon the ratio of linear to angular velocity in the motion trajectory and on subject orientation relative to the trajectory are present in a centrifuge paradigm. With this paradigm, two 3-min runs yields measures of: LVOR differentially modulated by different subject orientations in the two runs; OT dynamics in four conditions; two directions of "steady-state" OT, and two directions of AVOR. Efficient assessment of the dynamics (and of the underlying central integrative processes) may require a centrifuge radius of 1.0 meters or more. Clinical assessment of the spatial orientation system should include evaluation of central integrative processes that determine the dynamics of these responses.

Review, Tutorial↗
NASA NTRS2002

Influence of Cooling Channel Geometry on the Thermal Response in Silicon Nitride Plates Studied

Engine manufacturers are continually attempting to improve the performance and efficiency of internal combustion engines. Usually they raise the operating temperature or reduce the cooling air requirement for the hot section turbine components. However, the success of these attempts depends on finding materials that are lightweight, are strong, and can withstand high temperatures. Ceramics are among the top candidate materials considered for such harsh applications. They hold low-density, high-temperature strength, and thermal conductivity, and they are undergoing investigation as potential materials for replacing nickel-base alloys and superalloys that are currently used for engine hot-section components. Ceramic structures can withstand higher operating temperatures and a harsh combustion environment. In addition, their low densities relative to metals help reduce component mass. The long-term objectives of the High Temperature Propulsion Components (HOTPC) Project are to develop manufacturing technology, thermal and environmental barrier coatings (TBC/EBC), and the analytical modeling capability to predict thermomechanical stresses in minimally cooled silicon nitride turbine nozzle vanes under simulated engine conditions. Two- and three-dimensional finite element analyses with TBC were conducted at the NASA Glenn Research Center. Nondestructive evaluation was used to determine processing defects. The study included conducting preliminary parametric analytical runs of heat transfer and stress analyses under steady-state conditions to demonstrate the feasibility of using cooled Si3N4 parts for turbine applications. The influence of cooling-channel shapes (such as circular, square, and ascending-order cooling channels) on cooling efficiency and thermal stresses was investigated. Temperature distributions were generated for all cases considered under both cooling and no-cooling conditions, with air being the cooling medium. The table shows the magnitude of the maximum and minimum temperature obtained for the plates under air cooling. Each channel's cross-sectional shape delivered a different temperature; however, the two-dimensional analyses for circular and square or equal-side rectangular holes produced close results. Moreover, the model of the panel with ascending order cooling channels experienced the lowest temperature. A difference of near 260 C was found among the three cooling-hole configurations investigated. The ascending-order cooling channels arrangement showed superior performance by attaining the lowest temperature (1077 C) in comparison to the circular (1379 C) and square (1343 C) channels for the same cooling-hole size. This indicates that the panel with ascending-order cooling channels is the most suitable configuration regardless of the complexity involved in its manufacture. More details pertaining to this study are reported.

Abdul-Aziz, Ali↗
NASA NTRS2008

Current Sheet Formation in a Conical Theta Pinch Faraday Accelerator with Radio-frequency Assisted Discharge

Data from an inductive conical theta pinch accelerator are presented to gain insight into the process of inductive current sheet formation in the presence of a preionized background gas produced by a steady-state RF-discharge. The presence of a preionized plasma has been previously shown to allow for current sheet formation at lower discharge voltages and energies than those found in other pulsed inductive accelerator concepts, leading to greater accelerator efficiencies at lower power levels. Time-resolved magnetic probe measurements are obtained for different background pressures and pulse energies to characterize the effects of these parameters on current sheet formation. Indices are defined that describe time-resolved current sheet characteristics, such as the total current owing in the current sheet, the time-integrated total current ('strength'), and current sheet velocity. It is found that for a given electric field strength, maximums in total current, strength, and velocity occur for one particular background pressure. At other pressures, these current sheet indices are considerably smaller. The trends observed in these indices are explained in terms of the principles behind Townsend breakdown that lead to a dependence on the ratio of the electric field to the background pressure. Time-integrated photographic data are also obtained at the same experimental conditions, and qualitatively they compare quite favorably with the time-resolved magnetic field data.

Polzin, Kurt A.↗
DOE OSTI2021

Kinetic Measurements in Heterogeneous Catalysis

This contribution is about the experimental determination of the rate of a heterogeneous catalytic reaction and the analysis of kinetic data. In this case, the reaction rate can be defined as the frequency at which the closed sequence of elementary steps transforming reactants into products is occurring. However, the rate of chemical reaction is not directly observed; rather, one records the rate of substance change. The rate of chemical reaction is calculated based on the rate of substance change and assumed stoichiometry of the reaction. In order to make this an intensive quantity (i.e., independent of the volume in which the reaction is performed, this frequency is divided by the latter or by a quantity proportional to the latter). As the focus of what follows is on heterogeneously catalyzed reactions this can be the catalyst mass, the catalyst surface area or the total number of active sites present in the reaction volume confined by the walls of a chemical reactor. For example, the rate may be reported as one of the following: Net rate of consumption/production of component i mol m-3 s-1 Net specific rate of consumption/production of component i mol kg-1 s-1 Rate of substance change (per unit volume of catalyst) mol m-3 s-1 Specific reaction rate (per unit mass of catalyst) mol kg-1 s-1 Net rate of consumption/production of component i mol m-2 s-1 The turnover frequency (TOF) is a characteristic originally introduced by Boudart [1] is expressed as TOF=R/G_tot , where R is the steady-state rate of reactant consumption or product generation and G_totis the total areal density of active sites [mol m-2]. The latter is typically taken from experimental chemisorption data obtained at low temperature. The advancement of a chemical reaction leads to changes in the amounts of reactants and products which, for a stoichiometric single reaction, are connected by the stoichiometric coefficients. In many cases, for the sake of simplicity, we will assume that the investigated reaction proceeds according to a single reaction pathway, so that the net production rate of a reaction component is directly proportional to the reaction rate and that the latter equals the net production rate of any of the involved components when divided by the appropriate stoichiometric coefficient. For complex stoichiometric reactions the net production rates of the involved components are linear combinations of the reaction rates. Different goals for kinetic measurements can be formulated: Catalyst testing, i.e., obtaining the kinetic dependences for the development and discrimination of efficient catalytic materials. Precise kinetic characterization of active materials via high-throughput screening is a part of such activity. Detailed kinetics, i.e., revealing the detailed mechanism of complex catalytic reaction via systematic kinetic studies, both steady-state and non-steady-state Industrial kinetics, i.e., obtaining data and relationships for describing and predicting the behaviour of catalytic reactors and processes at industrial scale Finally, mathematical modeling and analysis where kinetic measurements provide data for understanding complex kinetic phenomena, e.g., oscillations, non-linear self-organization, etc.

36 MATERIALS SCIENCE↗
NASA NTRS1975

Determination of electron temperature in a penning discharge by the helium line ratio method

The helium line ratio technique was used to determine electron temperatures in a toroidal steady-state Penning discharge operating in helium. Due to the low background pressure, less than .0001 torr, and the low electron density, the corona model is expected to provide a good description of the excitation processes in this discharge. In addition, by varying the Penning discharge anode voltage and background pressure, it is possible to vary the electron temperature as measured by the line ratio technique over a wide range (10 to 100+ eV). These discharge characteristics allow a detailed comparison of electron temperatures measured from different possible line ratios over a wide range of temperatures and under reproducible steady-state conditions. Good agreement is found between temperatures determined from different neutral line ratios, but use of the helium ion line results in a temperature systematically 10 eV high compared to that from the neutral lines.

Richardson, R. W.↗
NASA NTRS1976

Transient excitation and data processing techniques employing the fast fourier transform for aeroelastic testing

The development of testing techniques useful in airplane ground resonance testing, wind tunnel aeroelastic model testing, and airplane flight flutter testing is presented. Included is the consideration of impulsive excitation, steady-state sinusoidal excitation, and random and pseudorandom excitation. Reasons for the selection of fast sine sweeps for transient excitation are given. The use of the fast fourier transform dynamic analyzer (HP-5451B) is presented, together with a curve fitting data process in the Laplace domain to experimentally evaluate values of generalized mass, model frequencies, dampings, and mode shapes. The effects of poor signal to noise ratios due to turbulence creating data variance are discussed. Data manipulation techniques used to overcome variance problems are also included. The experience is described that was gained by using these techniques since the early stages of the SST program. Data measured during 747 flight flutter tests, and SST, YC-14, and 727 empennage flutter model tests are included.

Jennings, W. P.↗
DOE OSTI2023

Impact of Actinide Complexation on Ligand Radiolysis

Although the actinides boast many unique physical and chemical properties, their inherent susceptibility to radioactive decay are what make them truly interesting elements to study. The absorption of ionizing radiation from actinide decay leads to the formation of a variety of transient and steady-state radicals, ions, and molecular radiolysis products that can lead to significant changes in the surrounding environment, and ultimately dictate steady-state actinide redox distributions and the longevity of molecules designed for actinide complexation. Radiolysis of the latter leads to complexant destruction and the concomitant formation of degradation products that can complicate actinide studies and processes. However, the radiation chemistry of most actinide complexants have been studied in the absence of the actinides they were designed to complex, which can lead to inaccurate conclusions on longevity and degradation product distributions, as metal ion complexation has been historically shown to influence a ligand’s radiolytic behavior. Consequently, bridging this knowledge gap is important for actinide science. Here, I will discuss the impact of actinide complexation on the steady-state and time-resolved radiation-induced reactivity of a variety of complexants, including, tributyl phosphate (TBP) and N,N,N',N'-tetraoctyl diglycolamide (TODGA) .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗