Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solidification microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Understanding Weld Formation and Microstructure Evolution in Laser Welded Stainless Steels and Ti-6Al-4V

High energy density welding processes are used for many industrial applications, such as aerospace and defense, and certain joint configurations and welding situations render post-weld inspection techniques difficult. Due to the inability to confirm penetration, there is a continual industrial need to improve prediction capabilities to aid in parameter selection. It is also necessary to understand the microstructural evolution to modify phase fractions and mitigate weldability related concerns such as solidification cracking or reduced corrosion performance.

42 ENGINEERING↗

Effect of laser surface remelting on the microstructure and properties of Al-Al2Cu-Si ternary eutectic alloy

Bimodal ultrafine eutectic composites (BUECs) exhibit a good combination of strength and plasticity owing to a dual-hierarchy in eutectic length-scales in the microstructure. The present study investigates the variation of phase, morphology, feature length-scales and modality of microstructures obtained in a Al81Cu13Si6 (at. %) ternary alloy after laser surface remelting. A novel approach of varying component bimodal eutectic volume fractions by controlling the cooling rate of the laser solidification process has been presented. The volume fraction of the fine eutectic matrix has a profound effect on the flow strength. Laser remelted microstructures with volume fractions of the fine eutectic varying from 25 to 40% exhibiting compressive flow strengths ranging from 500 to 900MPa have been obtained. The volume fraction of the fine eutectic decreased with cooling rate and completely ceased to exist at cooling rates greater than 4 × 10 °C/s 4 .

36 MATERIALS SCIENCE↗

The mechanism of eutectic growth in highly anisotropic materials

In the past 50 years, there has been increasing interest—both theoretically and experimentally—in the problem of pattern formation of a moving boundary, such as a solidification front. One example of pattern formation is that of irregular eutectic solidification, in which the solid–liquid interface is non-isothermal and the interphase spacing varies in ways that are poorly understood. Here, we identify the growth mode of irregular eutectics, using reconstructions from four-dimensional (that is, time and space resolved) X-ray microtomography. Our results show that the eutectic growth process can be markedly different from that seen in previously used model systems and theories based on the ex situ analysis of microstructure. In light of our experimental findings, we present a coherent growth model of irregular eutectic solidification.

Science & Technology - Other Topics↗

Geometry-Dependent Solidification Regimes in Metal Additive Manufacturing

Recent modeling and experimental work in additive manufacturing has suggested that cross-sectional geometry may play a significant role in the local development of the solidification structure through its influence on the heat source path. This effect has been rationalized as the transition from a quasi-static point heat source regime, to a regime dominated by the quasi-static motion of an equivalent line source. This work provides a simple analytical framework for determining the conditions under which a system transitions between these regimes. Here, a transient semi-analytical heat transfer model is used to examine a wide range of process conditions and material properties. A simple analytical expression is derived and shown to accurately predict the transition between solidification regimes over these conditions. The functional form of this expression is then used to help understand the importance of various material properties, process parameters, and geometric factors on the characteristics of the solidification conditions. This approach may be used as a simple guideline for optimizing process conditions in response to variations in cross-sectional geometry to produce more consistent microstructural distributions in additively manufactured components.

36 MATERIALS SCIENCE↗

Quantitative probing of the fast particle motion during the solidification of battery electrodes

Synchrotron x-ray tomography represents one of the most powerful imaging techniques that can visualize the three-dimensional microstructural complexity with a high spatial resolution. To date, however, the temporal resolution of this technique has been handicapped by the intrinsic limitations in the data acquisition speed and the lack of a suitable data processing method. The present study aims to fundamentally resolve this challenge by implementing a data analysis method that is based on differentiating discrete tomography reconstruction from a continuous scan reconstruction. With this methodological development, we capture and quantify the particle motion during the solidification of battery electrodes and reveal the statistics of the dynamically evolving motion in the drying process, which has been challenging to resolve. We discover that the particle motion exhibits a strong dependence on its geometric location within a drying electrode. Our results also imply that the final electrode quality can be controlled by balancing the solvent evaporation rate and the particle mobility in the region close to the drying surface.

25 ENERGY STORAGE↗

Laser spot welding of additive manufactured 304L stainless steel

Here, the goal of this work is to understand if an additively manufactured 304L stainless steel exhibits similar spot-welding behavior as wrought 304L stainless steel. Due to the many differences between an additively manufactured component and wrought product, it is important to determine how the material interacts with the laser and how it affects the weld bead morphology. In this paper, the laser coupling efficiency, weld size, and solidification of spot welds produced in wrought and additively manufactured 304L stainless steel were investigated. The coupling efficiency of wrought and additively manufactured 304L stainless steel of similar surface condition were approximately the same over a range of applied laser energies. Laser welding of the untreated (rougher) surface of additively manufactured 304L, however, showed improved coupling efficiency ranging between 3.3 and 100%. The rougher surface traps the incoming light and increases the coupling efficiency at lower laser energies, while at higher energy, the absorption efficiency is dominated by intrinsic absorption from the keyhole formation rather than surface roughness. The resulting spot weld microstructures differed from welds made in wrought 304L and additively manufactured 304L. Welds made in wrought 304L were fully austenitic containing what is suspected to be massive austenite, which suggests that these welds solidified as primary ferrite. Welds made in additively manufactured 304L were also fully austenitic and contained both cellular austenite and what is suspected to be massive austenite. These observations mean that welds made in additively manufactured 304L solidified as primary ferrite and primary austenite. The differences in weld microstructures made in wrought and AM 304L can be attributed to differences in the composition and solidification rate.

304L stainless steel↗

Analyzing the microstructural evolution and hardening response of an Al-Si-Mg casting alloy with Cr addition

Highlights: • The formation of β-Al{sub 5}FeSi intermetallics was suppressed since impurity Fe has been consumed by Al{sub 13}Cr{sub 4}Si{sub 4} intermetallics; • A large number of Al{sub 13}Cr{sub 4}Si{sub 4} dispersoids were observed in Al dendrites in the as-quenched and aged alloy; • The precipitation of Cr-bearing dispersoids harden the as-quenched alloy by over 10HV; • The current thermodynamic database underestimate the solubility of Fe in Al{sub 13}Cr{sub 4}Si{sub 4} intermetallics during solidification simulation. - Abstract: Chromium is added to Al-Si based casting alloys for the mitigation of die soldering. In the present work, EBSD, EDS and TEM characterizations are combined with thermodynamic simulations to study the microstructural evolution and hardening response of an Al-Si-Mg-Cr casting alloy during heat treatments. It is shown that the Fe-containing intermetallic compounds formed in the inter-dendritic region were acicular π-Al{sub 8}(Fe, Cr)Mg{sub 3}Si{sub 6} phase and polyhedral Al-(Cr, Fe)-Si phase which is structurally similar to face-centered cubic Al{sub 13}Cr{sub 4}Si{sub 4}. The polyhedral Al-(Cr, Fe)-Si intermetallics that crystallized prior to β-Al{sub 5}FeSi consumed impurity Fe, suppressing the formation of β phase during gravity die casting process. Also, Cr-addition enables the precipitation of nano-scale Cr-bearing dispersoids in Al dendrite during solution treatment at 813 K. Hardness increment of over 10 HV can be induced by the Cr-bearing dispersoids for as-quenched alloy. Though the dispersoids have a moderate hardening effect on the as-quenched alloy, they may impair the ageing hardening response by acting as heterogeneous nucleation sites for coarse Mg-Si rods and Si particles when quenching into water at 338 K.

36 MATERIALS SCIENCE↗

Influence of solidification structures on radiation-induced swelling in an additively-manufactured austenitic stainless steel

Metal additive manufacturing offers potential advantages for producing structural materials, such as austenitic stainless steels, in nuclear power systems. However, the microstructure developed during metal additive processing is notably different from the one developed in conventional processing, and the influence of the microstructural differences on performance in radiation environments has not been fully quantified. Using heavy ion irradiation and transmission electron microscopy, the radiation-induced swelling response of a laser powder-bed fusion-manufactured austenitic stainless steel was investigated at high doses. The influence of solidification-induced dislocation and precipitate structures was studied by comparing the radiation-induced swelling response of a 316L stainless steel in three microstructural states: as-fabricated, solution annealed, and fully recrystallized. Void swelling was approximately twice as pronounced in the as-fabricated state compared to post-processed states. In the framework of the rate theory for radiation effects, the higher swelling in the as-fabricated state can be explained by the strong sink bias for interstitial point defects exerted by the intermediate density of pre-existing dislocations. Void swelling was inhibited in the vicinity of pre-existing precipitates, but the density of precipitates in the as-fabricated material was not enough to compensate for the increase in swelling caused by dislocations.

36 MATERIALS SCIENCE↗

Molecular dynamics simulation of phase competition in terbium

The competition among multiple solid phases determines the final microstructures of a material. Such competition can originate at the very beginning of the solidification process. We report the results of molecular dynamics simulation of the phase competition between the hexagonal close-packed (hcp), face-centered cubic (fcc), and body-centered cubic (bcc) phases during the solidification of pure Tb. We found that the liquid supercooled below the hcp melting temperature has both bcc and hcp/fcc nuclei, but only the bcc nuclei grow such that the liquid always solidifies into the bcc phase, even at temperatures where the hcp phase is more stable. The hcp phase can only form in the last liquid droplet or at the bcc grain boundaries. Depending on the bcc grain orientations, the hcp phase jammed between the bcc grains either completely disappears or slowly grows via a solid-state massive transformation mechanism. Once the hcp phase becomes large enough, the stresses associated with its appearance can trigger a martensitic transformation. Yet, not the entire bcc phase is consumed by the martensitic transformation and the remaining bcc phase is transformed into the hcp phase via the solid-state massive transformation mechanism. If the supercooling is too large, the nucleation becomes almost barrier free and the liquid solidifies into a structure consisting of ultra-fine hcp and bcc grains after which the bcc phase quickly disappears.

36 MATERIALS SCIENCE↗

Evaluation of Equiatomic CrMnFeCoNiCu System and Subsequent Derivation of a Non-Equiatomic MnFeCoNiCu Alloy

Investigation into non-equiatomic high-entropy alloys has grown in recent years due to questions about the role of entropy stabilization in forming single-phase solid solutions. Non-equiatomic alloys have been shown to retain the outstanding mechanical properties exhibited by their equiatomic counterparts and even improve electrical, thermal, and magnetic properties, albeit with relaxed composition bounds. However, much remains to understand the processing–structure–property relationships in all classes of so-called high-entropy alloys (HEAs). Here, we are motivated by the natural phenomena of crystal growth and equilibrium conditions to introduce a method of HEA development where controlled processing conditions determine the most probable and stable composition. This is demonstrated by cooling an equiatomic CrMnFeCoNiCu alloy from the melt steadily over 3 days (cooling rate ~4 °C/h). The result is an alloy containing large Cr-rich precipitates and an almost Cr-free matrix exhibiting compositions within the MnFeCoNiCu system (with trace amounts of Cr). From this juncture, it is argued that the most stable composition is within the CrMnFeCoNiCu system rather than the CrMnFeCoNi system. With further optimization and evaluation, a unique non-equiatomic alloy, Mn 17 Fe 21 Co 24 Ni 24 Cu 14 , is derived. The alloy solidifies and recrystallizes into a single-phase face-centered cubic (FCC) polycrystal. In addition to possible applications where Invar is currently utilized, this alloy can be used in fundamental studies that contrast its behavior with its equiatomic counterpart and shed light on the development of HEAs.

36 MATERIALS SCIENCE↗

Residual stresses and microstructure within Allvac 718Plus laser powder bed fusion bars

The residual stresses within Allvac 718Plus bars built using LBPF with different laser powers, speeds and table displacements were measured using diffraction and mechanical methods and modelled with the baseplate attached and then removed. The residual stress profiles within the bars from the top surface down through the bulk were all quite similar, becoming less tensile due to a strain hardening mechanism. Table displacement has the greatest impact on residual stress, decreasing with increasing displacement/powder layer thickness. There was good agreement amongst the modeling and measurements. The microstructures were examined and varied slightly with energy density with higher densities having larger grains and enhanced post solidification diffusion. We found energy density had minimal impact on the residuals stresses within the parameters to produce dense material.

36 MATERIALS SCIENCE↗

Formation of intermetallic structures at the interface of steel-to-aluminium explosive welds

Highlights: • The interface of Fe-Al explosive welds was characterised by SEM/EDS and EBSD. • The intermetallics formed at the weld interface are rich in Al (Fe{sub 4}Al{sub 13}, Fe{sub 2}Al{sub 5}). • The presence of intermetallic phases on the interface deeply affects the weldability. • Al-rich intermetallics increase the solidification time of the weld interface. - Abstract: The formation of intermetallic structures at the interface of carbon steel to 6082 aluminium alloy explosive welds and their influence on the weldability of these two materials were studied. The morphology, the microstructure, the chemical and phase compositions of the welds were characterised by several types of microscopy techniques. The interface characterisation proved that explosive mixtures with a lower detonation velocity were revealed as being more suitable for achieving consistent welds since jet entrapment was prevented and continuous molten layers were not formed at the weld interface. It was also found that the physical properties of the intermetallic phases generated at the weld interface have a strong influence on the weldability of steel-to-aluminium explosive welds. Specifically, it was shown that the formation of aluminium-rich intermetallic phases at the weld interface increases the solidification time of the interfacial molten material, decreasing the weldability of these two materials. The formation of these intermetallic compounds should be avoided by reducing the interaction between the flyer and the baseplate as well as by avoiding excessive molten layers.

36 MATERIALS SCIENCE↗

In situ synchrotron X-ray imaging of 4140 steel laser powder bed fusion

In this study, an in situ synchrotron X-ray imaging technique was used to examine laser powder bed fusion (LPBF) of a chrome-molybedum, AISI 4140, ferrite–bainite steel, from a moving laser source. Since 4140 has received only minimal attention in the AM literature, focus here was on the effects of melt pool dynamics, vapor cavity depths, build layer height, and the origin of porosity on the 4140 as-built microstructure. Four build parameter sets, which enabled variation of laser power, scan speed, laser spot size, and specific energy density (SED), were applied. Vapor cavity and melt pool depths were measured for each single-track laser scan. Direct imaging of the LPBF process demonstrated that the primary source of porosity in the build originates from incorporation of entrapped gas within the powder irrespective of build parameter set. High resolution SEM and EBSD demonstrated that the as-built microstructure did not vary significantly with build parameter set over a broad range of SED. The fast solidification rates observed (0.06–0.08 m/s) lead to fine martensite packet/block size distributions (1–3 µm) with the potential for increased material strength.

36 MATERIALS SCIENCE↗

Microstructural analysis of laser weld fusion zone in Haynes 282 superalloy

Analytical electron microscopy and spectroscopy analyses of the fusion zone (FZ) microstructure in autogenous laser beam welded Haynes 282 (HY 282) superalloy were performed. The micro-segregation patterns observed in the FZ indicate that Co, Cr and Al exhibited a nearly uniform distribution between the dendrite core and interdendritic regions while Ti and Mo were rejected into the interdendritic liquid during the weld solidification. Transmission electron diffraction analysis and energy dispersive X-ray microanalysis revealed the second phase particles formed along the FZ interdendritic region to be Ti-Mo rich MC-type carbide particles. Weld FZ solidification cracking, which is sometimes associated with the formation of {gamma}-{gamma}' eutectic in {gamma}' precipitation strengthened nickel-base superalloys, was not observed in the HY 282 superalloy. Modified primary solidification path due to carbon addition in the newly developed superalloy is used to explain preclusion of weld FZ solidification cracking in the material. - Highlights: Black-Right-Pointing-Pointer A newly developed superalloy was welded by CO{sub 2} laser beam joining technique. Black-Right-Pointing-Pointer Electron microscopy characterization of the weld microstructure was performed. Black-Right-Pointing-Pointer Identified interdendritic microconstituents consist of MC-type carbides. Black-Right-Pointing-Pointer Modification of primary solidification path is used to explain cracking resistance.

36 MATERIALS SCIENCE↗

Interaction between laser radiation and metallic powder of 316L austenitic steel during selective laser melting

Highlights: • Single and multiple tracks on a loose bulk powder substrate were generated. • Understanding of the microstructure development during SLM was achieved. • Single tracks reveal a nearly symmetrical crystallography with elongated grains. • Multiple tracks show elongated grains perpendicular to the build direction. - Abstract: During selective laser melting (SLM), a complex heat state develops that leads to a characteristic crystallography and microstructure of the processed materials. Depending on the geometry of the processed part, most scan tracks of a new layer, so-called hatches, are located above a dense substrate or already solidified structures whereas others are located above loose powder. This is, inter alia, the case for overhanging structures. Attributable to the lower thermal conductivity of loose powder, temperature gradients and cooling rates of the melt pool differentiate in these areas, resulting in a different microstructural build-up. In this work, the microstructure and the crystallographic orientation of grade 316L austenitic stainless steel processed by SLM was investigated to understand the interaction between the laser radiation and the metallic powder during SLM-processing and to investigate the remelting of a track on a previous SLM-densified track. Single and multiple tracks on a loose bulk powder substrate, as well as single tracks on a dense substrate plate, were generated. A parameter study revealed that high energy densities are necessary to build continuous tracks on a loose bulk powder substrate. In addition, the amount of adhered particles, which are sintered on the fully melted and solidified tracks, is determined in comparison to the melted powder because the sintered particles strongly influence the surface roughness. To understand the microstructure development and, particularly, the influence of adjacent hatches during SLM-processing, investigations on the resulting microstructure and crystallographic orientation of a single track and two connected multiple tracks were carried out. During SLM processing of the tracks, the substrate plate and the solidified structures influence the temperature gradient and cooling rate of the melt pool, thus directionally solidified and elongated grains occur. Furthermore, the solidification is characterized by an epitaxial growth due to a distinct thermal gradient between the melt pool and the surrounding elements.

36 MATERIALS SCIENCE↗

Evaluation of the Microstructure and Performance of Fe-21Cr-15Ni-6Mn-Nb Nonmagnetic Stainless Steel Welded Joints

In the present study, double-sided gas shield welding (GSW), in a single pass, was applied to Fe-21Cr-15Ni-6Mn-Nb nonmagnetic stainless steel plate. The microstructure and performance of the welded joint were investigated via microstructural and phase analysis, mechanical testing and magnetic analysis. The results showed a satisfactory micrographic appearance with full penetration, and no solidification defects observed in the welded joint, which showed typical epitaxial growth characteristics in the welding solidification. Slight grain growth, with an average size of ~ 18.9 μm, occurred in the heat-affected zone (HAZ). The primary dendrite arms, on both sides of welding joint, grew along the direction of the temperature gradient and met at the centerline of the weld with no parting microstructure in evidence. The secondary dendrite arm spacing was stable in all parts of the weld zone (WZ). The hardness of the weld zone was higher than that of the HAZ and the base metal (BM), with the lowest hardness occurring in the HAZ. The results of tensile testing showed a higher strength of the welded metal (WM) compared to the BM, and a good strength-ductility balance of the welded joint. The impact energy of the HAZ was higher than that of the WZ, corresponding to 60.5 J at room temperature and 52.7 J at − 196 °C. Microvoid coalescence, concurrent with crack propagation along the direction of the long axis of the dendritic sub-grains, was observed during plastic deformation in the WZ. Additionally, the excellent paramagnetic characteristics of the welded specimens were revealed.

36 MATERIALS SCIENCE↗

Defects and 3D structural inhomogeneity in electron beam additively manufactured Inconel 718

Highlights: • A protocol for 3D characterization of structure and defects in additively manufactured EBM 718 is presented. • Lack of fusion defects disrupt local microstructure, creating isolated regions of equiaxed grains. • Clustering of micron-scale nitrides is attributed to a particle rafting process. • Normalized size-number density relationship of carbides matches that of industrial ingots. • Removal of porosity via post-processing will not correct microstructural inhomogeneities created by lack of fusion defects. - Abstract: Material structure and defects created during additive manufacturing contribute to the variability in mechanical properties of these parts, limiting their use for critical applications. Three-dimensional crystallographic, structural, and chemical information in electron beam melted Inconel 718 was collected from the sub-micron to the millimeter scale using the TriBeam tomography system. The relationship of defects to the surrounding microstructure has been studied in detail. Lack of fusion defects created sharp discontinuities in the grain morphology that extended several build layers beyond the layer where the defect originated. Nitrides and carbides in the size range of 1.25 μm to 10 μm were observed throughout the volume, with pronounced nitride clustering. The similarities between solidification in additive manufacturing and traditional manufacturing processes are demonstrated by the comparable size and distribution of carbides measured for industrial-scale samples of 718. Defects created during additive manufacturing cannot be easily remedied via standard post-processing techniques, and will likely diminish the mechanical performance of additively manufactured parts.

36 MATERIALS SCIENCE↗

Study of microstructure and silicon segregation in cast iron using color etching and electron microprobe analysis

An investigation on silicon segregation of lamellar, compacted and nodular graphite iron was carried out by applying a selective, immersion color etching and a modified electron microprobe to study the microstructure. The color etched micrographs of the investigated cast irons by revealing the austenite phase have provided data about the chronology and mechanism of microstructure formation. Moreover, electron microprobe has provided two dimensional segregation maps of silicon. A good agreement was found between the segregation profile of silicon in the color etched microstructure and the silicon maps achieved by electron microprobe analysis. However, quantitative silicon investigation was found to be more accurate than color etching results to study the size of the eutectic colonies. - Highlights: • Sensitivity of a color etchant to silicon segregation is quantitatively demonstrated. • Si segregation measurement by EMPA approved the results achieved by color etching. • Color etched micrographs provided data about solidification mechanism in cast irons. • Austenite grain boundaries were identified by measuring the local Si concentration.

36 MATERIALS SCIENCE↗