Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solidification microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Solidification structures on carbon materials surface-melted by repetitive laser pulses

The solidification morphology of carbon materials surface-melted by laser radiation at atmospheric pressure is studied. Electron microscopy results indicate that melt solidification is accompanied by the formation of surface microstructures, presumably due to the Rayleigh-Taylor instability in the molten carbon. The instability increment and surface tension coefficient of molten carbon are estimated, and the penetration of carbon vapour into the melt during one laser pulse is examined using numerical simulation. (interaction of laser radiation with matter. laser plasma)

36 MATERIALS SCIENCE↗

Ultrahigh strength and plasticity in laser rapid solidified Al–Si nanoscale eutectics

As-cast Al–20wt.% Si alloys were processed via laser rapid solidification (LRS) techniques to create eutectic microstructures with nanoscale interconnected, nanotwinned Si fibers. LRS morphologies exhibit higher flow stress, exceeding 800 MPa and uniform plastic deformation above 20% compared to as-cast alloy that fractures at strains below 8% at flow strength of approximately 200 MPa. The strengthening mechanisms of LRS morphologies are interpreted in terms of the interfacial constraints: increase in yield strength as well as strain hardening rate due to nanoscale confined slip in fibrous Al–Si eutectic, and load transfer and eventual plasticity in the nanoscale Si fibers.

36 MATERIALS SCIENCE↗

Alloy and structural optimization of a directionally solidified lamellar eutectic alloy

Mechanical property characterization tests of a directionally solidified Ni-20 percent Cb-2.5 percent Al-6 percent Cr cellular eutectic turbine blade alloy demonstrated excellent long time creep stability and indicated intermediate temperature transverse tensile ductility and shear strength to be somewhat low for turbine blade applications. Alloy and structural optimization significantly improves these off-axis properties with no loss of longitudinal creep strength or stability. The optimized alloy-structure combination is a carbon modified Ni-20.1 percent Cb-2.5 percent Al-6.0 percent Cr-0.06 percent C composition processed under conditions producing plane front solidification and a fully-lamellar microstructure. With current processing technology, this alloy exhibits a creep-rupture advantage of 39 C over the best available nickel base superalloy, directionally solidified MAR M200+ Hf. While improved by about 20 percent, shear strength of the optimized alloy remains well below typical superalloy values.

Sheffler, K. D.↗

Rapid solidification research at the NASA Lewis Research Center

This paper describes the research program initiated at the NASA Lewis Research Center for the study of rapid solidification of high temperature materials, with the major purpose for the development of advanced high-temperature and heat-flux materials for aircraft and aerosphace applications. Particular attention is given to the development of three alloys: Ni-aluminides, Nb-alloys, and Cu-alloys. Rapid solidification processing yielded alloys with novel microstructures, very fine grain sizes, reduced chemical segregation, and metastable extended solid solutions.

Locci, Ivan E.↗

Controlled Temperature Gradient Improves Freezing Alloy

Controlled gradient of temperature in advancing zone of solidification increases fatigue life of directionally solidified nickel-base superalloy. Improved solidification process eliminates, reduces, or controls microstructure of deleterious brittle phases, including carbides and gamma/gamma prime eutectic. Also reduces microsegregation and makes discrete carbides (if present) become fine and blocky. Expected to improve properties of other alloys, of both directionally-solidified polycrystalline and single-crystal forms.

Schmidt, Deborah↗

Microgravity Processing of Oxide Superconductors

The primary goal is to understand the microstructures which develop under the nonequilibrium solidification conditions achieved by melt processing in copper oxide superconductor systems. More specifically, to define the liquidus at the Y- 1:2:3 composition, the Nd-1:2:3 composition, and several intermediate partial substitution points between pure Y-1:2:3 and Nd-1:2:3. A secondary goal has been to understand resultant solidification morphologies and pathways under a variety of experimental conditions and to use this knowledge to better characterize solidification phenomena in these systems.

Hofmeister, William H.↗

NASA MSFC Electrostatic Levitator (ESL) Rapid Quench System

Electrostatic levitation, a form of containerless processing, is an important tool in materials research. Levitated specimens are free from contact with a container; therefore, heterogeneous nucleation on container walls is not possible. This allows studies of deeply undercooled melts. Furthermore, studies of high‐temperature, highly reactive materials are also possible. Studies of the solidification and crystallization of undercooled melts is vital to the understanding of microstructure development, particularly the formation of alloys with unique properties by rapid solidification. The NASA Marshall Space Flight Center (MSFC) Electrostatic Levitator (ESL) lab has recently been upgraded to allow for rapid quenching of levitated materials. The ESL Rapid Quench System uses a small crucible‐like vessel that can be partially filled with a low melting point material, such as a Gallium alloy, as a quench medium. An undercooled sample can be dropped into the vessel to rapidly quench the sample. A carousel with nine vessels sits below the bottom electrode assembly. This system allows up to nine rapid quenches before having to break vacuum and remove the vessels. This new Rapid Quench System will allow materials science studies of undercooled materials and new materials development. In this presentation, the system is described and initial results are presented.

SanSoucie, Michael P.↗

Effects of Sr, Ce and P on the microstructure and mechanical properties of rapidly solidified Al7Si alloys

Highlights: • Rapid solidification caused formation of nanoscaled Si particle chains. • Sr or Ce induced the columnar transition zone only at extremely high cooling rate. • Enhancement of hardness is attributed to fine dispersion of eutectic Si, grain refinement and the supersaturation of Si. • Sr or Ce caused further enhancement of hardness, attributing to Si modification. - Abstract: A series of Al7Si based alloys with trace addition of Sr, Ce or P were prepared using melt-spinning at two different high cooling rates, and the microstructure as well as the hardness of the ribbons was comprehensively studied. The results show that Sr or Ce induces the formation of columnar transition zone and modifies the morphology of eutectic Si phase from dispersed particle chains to fine fibers only at extremely high cooling rate. However, P has little effect on the microstructure of either α-Al or eutectic Si. Compared with conventional casting, the Al7Si ribbons exhibit extremely high hardness due to the fine dispersion of eutectic Si, the grain refinement and the supersaturation of Si. The hardness is further enhanced by Sr or Ce addition at extremely high cooling rate, especially for columnar and equiaxed zones, attributing to the modification effect on Si phase.

36 MATERIALS SCIENCE↗

The influence of Nb, Ti, and Si additions on the liquidus and solidus temperatures and primary microstructure refinement in 0.3C-30Ni-18Cr cast steel

This study explores the effect of niobium, titanium and silicon on the liquidus and solidus temperatures and primary structural refinement in creep-resistant 0.3C-30Ni-18Cr cast steel. Fifteen test alloys were investigated. The concentrations of niobium, titanium and silicon in these alloys ranged from 0.03 to 3.0 wt.%, 0.03 to 1.42 wt.%, and 1.39 to 4.26 wt.%, respectively. It was found that an increase of these elements in 0.3C-30Ni-18Cr cast steel lowered the beginning and ending temperatures of the solidification process, extended the range of solidification temperatures, reduced the density, and refined the microstructure, i.e., reduced the secondary dendrite arm spacing. Alloys with the highest content of the examined elements were reported to contain carbide precipitates, as well as the G phase in an as-cast state.

36 MATERIALS SCIENCE↗

Microstructures and Mechanical Properties of Resistance Spot-Welded Steel/Aluminum Alloy Joints with Process Tapes

The microstructure and mechanical property of resistance spot-welded joints of steel and aluminum were studied by using process tapes. The steel/aluminum joint consists mainly of aluminum nugget and interface zone. The liquid nugget solidification has an epitaxial growth characteristic, and the interface zone displays a double-layer structure, Fe{sub 2}Al{sub 5} layer at steel side and Fe{sub 4}Al{sub 13} layer at aluminum nugget side. Compared with joints without process tape, the joint nugget diameter and tensile shear load increased by 35.45 and 10.98%, respectively, and its indentation ratio decreased by 56.25% due to the process tapes increasing heat input, producing larger nugget diameter and continuous interface layer, and protecting against deep indentation. The joining area of intermetallic layer and aluminum nugget is weak link in the joint. It is favorable to use the process tapes for improving welding quality, raising joint strength, and energy saving.

36 MATERIALS SCIENCE↗

Effect of Processing Parameters and Shape of Blade on the Solidification of Single-Crystal CMSX-4 Ni-Based Superalloy

The effect of mold withdrawal velocity, heater and pouring temperatures and the thickness of blade root on the solidification parameters and shape of the liquidus isotherm as well as microstructure of single-crystal CMSX-4 nickel-based superalloy, manufactured by the Bridgman method, has been analyzed in the article. The temperature gradient G, solidification rate v and location of the liquidus isotherm were determined in relation to the radiation baffle on the basis of temperature measurements conducted in nine test points along the height of castings (140 mm) with different thicknesses of root (27, 15 and 7 mm) and withdrawal velocities of 3 and 5 mm/min. The increase of root thickness, relative to the airfoil, resulted in the rise of inhomogeneity of solidification parameters as well as the primary dendrite arm spacing and unsteady state solidification along the whole blade height. However, in the case of blade with constant thickness, the steady-state solidification was created at the distance of 65 to 130 mm from its base. The increase of mold withdrawal velocity caused the decrease of temperature gradient. However, the solidification rate was different from the mold withdrawal velocity, especially in the root and middle part of the airfoil. The increase of heater temperature resulted in a rise of temperature gradient and reduction of the curvature of the liquidus isotherm, whereas the pouring temperature did not affect the solidification parameters in the blade. Particularly unfavorable conditions of the solidification process could occur in the middle part of the airfoil and root because of the lowest value of G/v and the largest primary dendrite arm spacing.

36 MATERIALS SCIENCE↗

Prediction of Cooling Curves for Controlled Unidirectional Solidification Under the Influence of Shrinkage: A Semi-analytical Approach

Quality of casting products can be significantly improved by controlling the crystal growth rate. Both dendritic and equiaxed grain structures depend strongly on crystal growth rate along the crystallographic direction. Uncontrolled solidification processes may lead to the formation of porous and columnar material with an extremely non-homogeneous composition distribution. These undesirable micro-structures can be avoided by adopting an optimal cooling rate (K/s) during the crystal growth. The present work focuses on determining suitable cooling curves to obtain desired unidirectional crystal growth rates, by implementing a semi-analytical model. Here, we defined cooling curve as the time history of temperature evolution at the cold boundary. The proposed semi-analytical heat transfer model is diffusion driven and accounts for shrinkage effect during solidification. The proposed model is found capable of predicting cooling curves for prescribed interface velocities. The model is self-sufficient in validating itself by means of solving inverse and forward problems. The cooling curve prediction by the model is validated by using it as the transient boundary condition for an existing enthalpy updating scheme-based numerical model. The proposed model is also applied to empirical data reported in literature, to validate the model against experimental results. All the validations showcased excellent fit. The proposed model will facilitate controlled unidirectional crystal growth rate by providing cooling rate (K/s) as an input for the experiments involving directional solidification.

36 MATERIALS SCIENCE↗

Solidification kinetics and metastable phase formation in binary Ti-Al

Electromagnetic levitation was used to solidify near-equiatomic alloys of Ti-Al at various bulk undercoolings. Detailed thermal histories were acquired during experiments using optical pyrometry with sampling rates as fast as 500 KHz. Solidification and other high-temperature transformation pathways were deduced from the thermal data and microstructural analysis. Recalescence rise times were employed to determine semiquantitative primary solidification kinetics for the different phases. Primary beta solidification was observed at compositions well into the equilibrium alpha regime; this is presented as part of a near-equiatomic nucleation domain diagram that shows the primary solidification phase that results for each combination of nucleation temperature and composition. Solidification kinetics are faster for primary beta than they are for primary alpha. For undercoolings less than about 150 K, the primary solidification kinetics are about an order of magnitude slower for gamma than for alpha.

Anderson, C. D.↗

Composition and automated crystal orientation mapping of rapid solidification products in hypoeutectic Al-4 at.%Cu alloys

Rapid solidification can produce metastable phases and unusual microstructure modifications in multi-component alloys during additive manufacturing or laser beam welding. Composition and phase mapping by transmission electron microscopy have been used in this paper to characterize the morphologically distinct zones developing in hypoeutectic Al-4 at.% Cu alloy after pulsed laser melting for different crystal growth rate regimes. Deviations of the compositions of the alloy phases from equilibrium predictions and unique orientation relationships between the solidification transformation products have been determined. Specifically, for the columnar growth zone at solidification rates of 0.8 m s - 1 < v < v a = 1.8 m s - 1 , two distinct orientation relationships were established between the concomitantly forming non-equilibrium phases, supersaturated α-Al solid solution and the discontinuously distributed α-Al 2 Cu-based θ'-phase, which can be described as {110} θ ∥ {001} α , [001] θ ∥ [110] α and {001} θ ∥ {001} α , [100] θ ∥ [100] α . These orientation relationships permit formation of coherent interphase interfaces with low interfacial free energy. Finally, this endows a kinetic advantage to the thermodynamically less stable θ'-Al 2 Cu phase relative to the more stable equilibrium θ-Al 2 Cu phase during formation of the morphologically modified eutectic of the columnar growth zone grains, since repeated nucleation is required to establish the discontinuous distribution of θ'-Al 2 Cu phase.

36 MATERIALS SCIENCE↗

Sensitivity of cellular automata grain structure predictions for high solidification rates

Understanding as-solidified grain structure development during constrained (G 0) alloy solidification conditions is a necessary component of understanding the larger process-microstructure relationships during additive manufacturing (AM) processing. This study applies a cellular automata (CA) model, for static solidification velocities and thermal gradients on the order of those expected in AM melt pools, to investigate grain shape development across ranges of input parameters governing temperature field evolution, nucleation, and growth. Variation in nucleated grain shape from columnar to equiaxed as a function of thermal gradient and nucleation density is modeled with CA and verified against the established transition model of Hunt and Gaumann. Furthermore, while thermal conditions and nucleation density are shown to have the largest roles on microstructure development, the sensitivity of grain structure was very unevenly distributed across parameter space. In particular, it was found that microstructure is very sensitive to mean nucleation undercooling and the interfacial response function in process space regimes near grain structure transitions, but entirely controlled by a combination of thermal gradient, solidification velocity, and nucleation density away from such transitions. The understanding of grain shape sensitivity obtained through CA modeling, particularly at large thermal gradient and nucleation density, will be necessary for accurate microstructure prediction during the extreme processing conditions and large input parameter uncertainty common to AM.

36 MATERIALS SCIENCE↗

Liquid Phase Miscibility Gap Materials

The manner in which the microstructural features of liquid-phase miscibility gap alloys develop was determined. This will allow control of the microstructures and the resultant properties of these alloys. The long-duration low gravity afforded by the shuttle will allow experiments supporting this research to be conducted with minimal interference from buoyancy effects and gravitationally driven convection currents. Ground base studies were conducted on Al-In, Cu-Pb, and Te-Tl alloys to determine the effect of cooling rate, composition, and interfacial energies on the phase separation and solidification processes that influence the development of microstructure in these alloys. Isothermal and directional cooling experiments and simulations are conducted. The ground based activities are used as a technological base from which flight experiments formulated and to which these flight experiments are compared.

Gelles, S. H.↗

Numerical Simulation and Experimental Validation of Nondendritic Structure Formation in Magnesium Alloy Under Oscillation and Ultrasonic Vibration

In this study, the formation of nondendritic structures in the primary phase of magnesium alloy solidified under oscillation and ultrasonic vibration was investigated by numerical simulation and experimentally. The growth and motion of a dendrite during solidification was simulated by a combination of the lattice Boltzmann method and the phase-field method. The simulation and experimental results indicated that higher oscillation amplitudes and acoustic streaming made the microstructures change from dendritic to nondendritic in the α-Mg primary phases. A sufficient shear stress and an appropriate flow time in the barrel should be satisfied when a given inclined angle is selected. The effects of the flow and the thermal field on the nucleation behavior, the constitutional undercooling, and the growth morphology are also discussed. It was found that a high shear rate and high turbulence can help homogenize the temperature and the concentration fields and collide and rotate the α-Mg primary phases.

36 MATERIALS SCIENCE↗

The Effect of Vanadium on Morphology and Chemical Composition of Carbides in High Alloyed Chromium–Molybdenum Steels

Despite of the permanent progress of technique and finding of the new, modern materials that successfully replace metals, steel continues to play an important role in the technical practice. The tendency is to discover the new alloys with better mechanical and technological characteristics, compared to conventional and standard types of steels. High-alloyed Cr–Mo steel, with a high content of Vanadium is the new type of wear resistant material, with high hardness and satisfactory impact and fracture toughness. During the solidification process Vanadium, as a strong carbide forming element, creates a network of M{sub 7}C{sub 3} type carbide grains around the metal matrix, while in the matrix, the finely dispersed V{sub 6}C{sub 5} type carbides are formed. In this paper, the chemical composition and morphology have been studied of carbides and the other phases present in the metal matrix in 1.4 wt % C, 12 wt % Cr, 1.0 wt % Mo steels with additions up to 3.0 wt % V. Experimental results indicate that Vanadium affects the solidification process in high Chromium steel. Vanadium is distributed between eutectic M{sub 7}C{sub 3} carbide and the matrix, but its content in carbides is considerably higher. Vanadium changed the microstructure parameters of phases present in the structure of alloys, including volume fraction, size and morphology.

36 MATERIALS SCIENCE↗