Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solid dissolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Solution and Solid State Structural Chemistry of Th(IV) and U(IV) 4-Hydroxybenzoates

Organic ligands with carboxylate functionalities have been shown to affect the solubility, speciation, and overall chemical behavior of tetravalent metal ions. While many reports have focused on actinide complexation by relatively simple monocarboxylates such as amino acids, here we examined Th(IV) and U(IV) complexation by 4-hydroxybenzoic acid in water with the aim of understanding the impact that the organic backbone has on the solution and solid state structural chemistry of thorium(IV) and uranium(IV) complexes. Two compounds of the general formula [An 6 O 4 (OH) 4 (H 2 O) 6 (4-HB) 12 ]· n H 2 O [An = Th ( Th-1 ) and U ( U-1 ); 4-HB = 4-hydroxybenzoate] were synthesized via roomtemperature reactions of AnCl 4 and 4-hydroxybenzoic acid in water. Solid state structures were determined by single-crystal X-ray diffraction, and the compounds were further characterized by Raman, infrared, and optical spectroscopies and thermogravimetry. The magnetism of U-1 was also examined. The structures of the Th and U compounds are isomorphous and are built from ligand-decorated oxo/hydroxo-bridged hexanuclear units. The relationship between the building units observed in the solid state structure of U-1 and those that exist in solution prior to crystallization as well as upon dissolution of U-1 in nonaqueous solvents was investigated using small-angle X-ray scattering, ultraviolet-visible optical spectroscopy, and dynamic light scattering. The evolution of U solution speciation as a function of reaction time and temperature was examined. Such effects as well as the impact of the ligand on the formation and evolution of hexanuclear U(IV) clusters to UO 2 nanoparticles compared to prior reported monocarboxylate ligand systems are discussed. Unlike prior reported syntheses of Th and U(IV) hexamers where the pH was adjusted to ~2 and 3, respectively, to drive hydrolysis, hexamer formation with the HB ligand appears to be promoted only by the ligand.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Humidity Effect on Nanoscale Electrochemistry in Solid Silver Ion Conductors and the Dual Nature of Its Locality

Scanning probe microscopy (SPM) is a powerful tool to investigate electrochemistry in nanoscale volumes. While most SPM-based studies have focused on reactions at the tip-surface junction, charge and mass conservation requires coupled and intrinsically non-local cathodic and anodic processes that can be significantly affected by ambient humidity. Here, we explore the role of water in both cathodic and anodic processes, associated charge transport, and topographic volume changes depending on the polarity of tip bias. The first-order reversal curve current-voltage technique combined with simultaneous detection of the sample topography, referred to as FORC-IVz, was applied to a silver solid ion conductor. We found that the protons generated from water affect silver ionic conduction, silver particle formation and dissolution, and mechanical integrity of the material. This work highlights the dual nature (simultaneously local and non-local) of electrochemical SPM studies, which should be considered for comprehensive understanding of nanoscale electrochemistry.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Exploring the Nature of f-Element Soft Donor Interactions Using Electronically Tunable Azolate Ionic Liquids

This project was undertaken to advance the understanding of how f-elements interact with moderately soft donors, a heavily investigated yet open question which is of prime importance in spent nuclear fuel processing and fundamental inorganic chemistry. During the course of the project, based on exciting results, a stretch goal was developed to study the hydrolysis products of transuranic actinide metals, a somewhat understudied field even with its significance in nuclear fuel cycle and impacts in environmental chemistry. The stretch goal was to take our serendipitous discovery of an easy route to isolation of crystalline multinuclear ƒ-element hydrolysis products, and apply it to gaining a mechanistic understanding of Pu(III/IV) colloid formation. The simplicity of our techniques should lend themselves to the remote handling required for study of many transuranic elements. We developed several methodologies using azolium azolate chemistry to overcome ƒ-element hydrolysis problems that prohibit the isolation of ƒ-element soft donor complexes and to build a crystallographic library of ƒ-element N-donor complexes as a means to understand the fundamental differences between actinide and lanthanide interactions with moderately soft donor ligands. Our next major endeavor will be to transfer this chemistry from 4ƒ elements to transuranic elements, particularly in the study of hydrolysis of Pu(III/IV). While our work is fundamental in nature, applications of the knowledge we are generating should be felt in such diverse fields as catalysis, separations in general, nuclear waste remediation specifically, and many other applications in f-element magnetic and luminescent properties. The potential ramifications of the consistent and robust formation of hydrolysis controlled hexanuclear lanthanide structures are enormous, with future uses being catalyst formation, higher-nuclearity structure synthesis using our hexanuclear motif as a fundamental building block, Pu waste remediation, separations, and many other potential applications resulting from characteristic magnetic and luminescent properties of lanthanide polynuclear structures. Three synthetic methodologies (direct mixing with variable stoichiometries, use of volatile solvent, metathesis) were developed starting with 7 acidic and 6 basic azoles to obtain ionic liquids suitable for f-element coordination. Proton transfer by acidic/basic azole combination led to suitable low melting salts and two cocrystals. Acid/base reaction of azoles with soft-donor permanent cations of ([X 4444 ][OH] (where [X 4444 ] + = tetrabutylammonium [N 4444 ] + or tetrabutylphosphonium [P 4444 ] + ) with weakly acidic azoles including imidazole, 1,2,3-triazole, 1,2,4-triazole, 5-aminotetrazole, 4,5-dicyanoimidazole, and 2-amino-4,5-dicyanoimidazole) revealed several suitable low-melting salts. Metathesis reactions of Na(azolate) were conducted by first using weakly acidic azoles including 4,5-dicyanoimidazole, 2-amino-4,5-dicyanoimidazole, 5-aminotetrazole, and 1,2,4-triazole to form sodium or lithium salts using group(I) hydroxides in methanolic solutions. The best results were obtained by reacting the basic and acidic azoles directly in 1:1 or 3:1 ratios at elevated temperatures. Twenty-two azole mixtures were identified which are either low melting solids or room temperature liquids. Each of the low melting solids was confirmed to be a new solid phase, each of which is being further characterized. The liquids and solids are anticipated to be ILs, eutectics, or partially ionized systems, all of which will be suitable for the dissolution of f-element salts. Five new synthetic methodologies were developed to finding suitable crystallization conditions for f-element complexation with the goal of finding simple one pot reaction syntheses and crystallization strategies that could be used under the demanding conditions of transuranic chemistries. These synthetic methods yield many new crystalline phases which were studied by single crystal X-ray diffraction.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Multi-scale and multi-technic microstructure analysis of a linear friction weld of the metastable-β titanium alloy Ti-5Al-2Sn-2Zr-4Mo-4Cr (Ti17) towards a new Post-Weld Heat Treatment

Highlights: • Soft joint showing sharp macro-zones and marked by asymmetrical process effects • Gradient of thermomechanical loads identified through progressive stages of transformation • Highly textured recrystallized β grains at the joint core with distorted β lattice • Lattices, phase fractions, microstructures and hardness homogenized after heat treatment - Abstract: Linear Friction Welding (LFW) is a solid-state joining process producing narrow joints mainly developed for the aircraft industry. The Thermo-Mechanical Processing (TMP) loads imposed on the material cause complex microstructure transformations. This study aimed at characterizing the local microstructures and crystallographic configurations to identify the mechanisms impacting the stability and the mechanical properties of a Ti17 LFW joint with the objective of establishing an innovative homogenizing Post-Weld Heat Treatment (PWHT). The process caused a narrow zone of ±2 mm from the friction interface to reach the isothermal α → β transformation temperature under a heating rate of 500 K/s followed by quenching (−100 K/s). The TMP resulted in the formation a ±3 mm wide soft Process Affected Zone (PAZ) delimited by three characteristic zones: the Welding Line (WL width ≈ 400 μm), The Thermo-Mechanically Affected Zone (TMAZ width ≈ 1 mm) and the Heat Affected Zone (HAZ). β TMP resulted in the total dissolution of the α phase in the joint core (WL + TMAZ) and formed strongly textured {110}<111> β recrystallized grains in the WL by continuous dynamic recrystallization of squeezed prior-β grains in the TMAZ. α + β TMP led to a gradual loss of hardness in the HAZ whose microstructure is similar to the one of the base material (BM) but is subject to gradual α laths dissolution due to the local temperatures experienced during LFW. A PWHT consisting in a β annealing followed by an α + β ageing resulted in a uniformly hardened weld with a homogenized Widmanstätten microstructure in the whole assembly.

36 MATERIALS SCIENCE↗

The analysis of magnesium oxide hydration in three-phase reaction system

In order to investigate the magnesium oxide hydration process in gas–liquid–solid (three-phase) reaction system, magnesium hydroxide was prepared by magnesium oxide hydration in liquid–solid (two-phase) and three-phase reaction systems. A semi-empirical model and the classical shrinking core model were used to fit the experimental data. The fitting result shows that both models describe well the hydration process of three-phase system, while only the semi-empirical model right for the hydration process of two-phase system. The characterization of the hydration product using X-Ray diffraction (XRD) and scanning electron microscope (SEM) was performed. The XRD and SEM show hydration process in the two-phase system follows common dissolution/precipitation mechanism. While in the three-phase system, the hydration process undergo MgO dissolution, Mg(OH){sub 2} precipitation, Mg(OH){sub 2} peeling off from MgO particle and leaving behind fresh MgO surface. - Graphical abstract: There was existence of a peeling-off process in the gas–liquid–solid (three-phase) MgO hydration system. - Highlights: • Magnesium oxide hydration in gas–liquid–solid system was investigated. • The experimental data in three-phase system could be fitted well by two models. • The morphology analysis suggested that there was existence of a peel-off process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Dissolution of Fe in HCl from the Ilmenite Concentrate; Evaluating the Effect of Operating Parameters and Mutual Interactions

Selective HCl dissolution of ilmenite components for obtaining Ti or titanium dioxide (TiO{sub 2}) has been highly recognized due to its advantages, greater environmental friendliness, and simplicity, compared to H{sub 2}SO{sub 4} and Cl{sub 2} methods. The effect of numerous parameters has been studied with the one-factor-at-a-time method. The present study aimed to evaluate the effect of key operation parameters, such as acid-to-solid ratio (A/S: 5 to 20 mL/g), reaction temperature (T: 70 °C to 100 °C), and acid concentration (A pct: 15 to 30 wt pct), on the dissolution of Fe in HCl solution with the minimum Ti losses to the leachate from its abundant, domestic, and low-cost mineral source (Kahnooj ilmenite concentrate) using central composite design–response surface methodology. After 90 minutes of leaching, the Ti/Fe (pct) in terms of dissolved amounts was selected as the process assessment response function. Based on the conducted experimental and statistical analysis, increasing the levels of parameters in the studied domain leads to an increase in Ti/Fe (pct), in the order of A pct > T > A/S. Two statistically significant mutual interactions between A/S-T and T-A pct, with 95 pct confidence level, were revealed for the first time in this study. The optimization strategy was set to the minimization of Ti/Fe (pct) by considering the objective of study and the selected response function. The A/S, T, and A pct were determined to be 5 mL/g, 70 °C, and 15 pct, respectively, for maximum impurity dissolution and minimum Ti loss to the leachate.

36 MATERIALS SCIENCE↗

First stage of reaction of molten Al with MgO substrate

The Al/MgO couple was produced in vacuum (~ 5 × 10{sup −} {sup 4} Pa) by contact heating from RT up to 1000 °C and holding at that temperature for 1 h of a small 4 × 4 × 4 mm aluminium (5 N) sample placed on the [100] MgO single crystal substrate. TEM observations backed with electron diffraction analysis indicated that the interaction between liquid aluminium and MgO starts from a redox reaction producing a continuous layer of MgAl{sub 2}O{sub 4} spinel on the substrate surface. Its growth is controlled by solid state out-diffusion of magnesium and oxygen towards the surface being in contact with liquid metal. The thickening of spinel layer is accompanied by its cracking and infiltration with aluminium. The above process enables local dissolution of the MgO substrate and formation in it of a thin region of interpenetrating metallic channels walled with spinel. The removal of dissolved magnesium through open aluminium channels towards the drop and to vacuum locally produces areas of aluminium enriched with dissolved oxygen, which results in the nucleation of α-Al{sub 2}O{sub 3} at spinel clad walls. The growth of α-Al{sub 2}O{sub 3} is controlled only by the dissolution rate of MgO by aluminium, liquid state diffusion of Mg to drop/vacuum and oxygen to the front of the of α-Al{sub 2}O{sub 3} crystallites growing into MgO substrate. - Highlights: • New unique evidence of first stages of interaction of liquid Al with MgO substrates • Interaction of liquid Al with MgO starts with the formation of a layer MgAl{sub 2}O{sub 4}. • Growth of MgAl{sub 2}O{sub 4} is slow as controlled by solid state out-diffusion of Mg and O. • MgAl{sub 2}O{sub 4} serves as a nucleation site for Al{sub 2}O{sub 3} and consumed by it soon after. • Growth of Al{sub 2}O{sub 3} is fast as controlled by diffusion in liquid state.

36 MATERIALS SCIENCE↗

DISSOLUTION OF 3013-DE SAMPLE 10-16

The HB-Line Facility has a long-term mission to dissolve and disposition legacy fissile materials. HB-Line dissolves plutonium dioxide (PuO{sub 2}) from K-Area parting support of the 3013 Destructive Examination (DE) program. The PuO{sub 2}-bearing solids originate from a variety of unit operations and processing facilities, but all of the material is assumed to be high-fired (i.e., calcined in air for a minimum of two hours at {ge} 750 C). The Savannah River National Laboratory (SRNL) conducted dissolution flowsheet studies on 3013 DE Sample 10-16 (can R610826), which contains weapons-grade plutonium (Pu) as the fissile material. The dissolution flowsheet study was performed for 4 hours at 108 C on unwashed material using 12 M nitric acid (HNO{sub 3}) containing 0.20 M potassium fluoride (KF). After 4 hours at 108 C, the {sup 239}Pu Equivalent concentration was 32.5 g/L (gamma, 5.0% uncertainty). The insoluble residue comprised 9.88 wt % of the initial bulk weight, and contained 5.31-5.95 wt % of the initial Pu. The residue contained Pu in the highest concentration, followed by tungsten (W). Analyses detected 2,770 mg/L chloride (Cl{sup -}) in the final dissolver solution (3.28 wt %), which is significantly lower than the amount of Cl{sup -} detected by prompt gamma (9.86 wt %) and the 3013 DE Surveillance program (14.7 wt %). A low bias in chloride measurement is anticipated due to volatilization during the experiment. Gas generation studies found approximately 60 mL of gas per gram of sample produced during the first 30 minutes of dissolution. Little to no gas was produced after the first 30 minutes. Hydrogen gas (H{sub 2}) was not detected in the sample. Based on detection limits and accounting for dilution, the generated gas contained < 0.12 vol % H{sub 2}, which is well below the 4.0 vol % flammability limit for H{sub 2} in air. Filtration of the dissolver solution occurred readily. When aluminum nitrate nonahydrate (ANN) was added to the filtered dissolver solution at a 3:1 Al:F molar ratio, and stored at room temperature for 24 hours, the solution filtered approximately 6 times slower than when filtered 30 minutes after ANN addition, requiring 6 minutes to complete compared to 55 seconds for the first filtration. It is likely that the ambient-temperature solubility for ANN was exceeded. A 4-hour dissolution time at a temperature of 108 C in 12 M HNO{sub 3}/0.2 M KF is recommended for dissolution of this material.

08 HYDROGEN↗

Formation of titanium phosphate composites during phosphoric acid decomposition of natural sphene

Decomposition of mineral sphene, CaTiOSiO{sub 4}, by H{sub 3}PO{sub 4} is investigated in detail. During the dissolution process, simultaneous calcium leaching and formation of titanium phosphate (TiP) take place. The main product of decomposition is a solid titanium phosphate-silica composite. The XRD, solid-sate NMR, IR, TGA, SEM and BET data were used to identify and characterize the composite as a mixture of crystalline Ti(HPO{sub 4}){sub 2}.H{sub 2}O and silica. When 80% phosphoric acid is used the decomposition degree is higher than 98% and calcium is completely transferred into the liquid phase. Formation of Ti(HPO{sub 4}){sub 2}.H{sub 2}O proceeds via formation of meta-stable titanium phosphate phases, Ti(H{sub 2}PO{sub 4})(PO{sub 4}).2H{sub 2}O and Ti(H{sub 2}PO{sub 4})(PO{sub 4}). The sorption affinities of TiP composites were examined in relation to caesium and strontium ions. A decrease of H{sub 3}PO{sub 4} concentration leads to formation of composites with greater sorption properties. The maximum sorption capacity of TiP is observed when 60% H{sub 3}PO{sub 4} is used in sphene decomposition. The work demonstrates a valuable option within the Ti(HPO{sub 4}){sub 2}.H{sub 2}O-SiO{sub 2} composite synthesis scheme, to use phosphoric acid flows for isolation of CaHPO{sub 4}.2H{sub 2}O fertilizer. - Graphical abstract: A new synthesis scheme for preparation of composite titanium phosphate (TiP) ion-exchangers upon one-stage decomposition process of natural sphene with phosphoric acid is presented. Syntheses of {alpha}-TiP-silica composites proceed via formation of meta-stable titanium phosphate phases. The concentration of H{sub 3}PO{sub 4} determines the porosity of final products and their sorption affinities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Empirical kinetics and their role in elucidating the utility of transition-state theory to mineral–water reactions. A comment upon, ''Evidence and Potential Implications of Exponential Tails to Concentration Versus Time Plots for the Batch Dissolution of Calcite'' by V. W. Truesdale

Transition-state theory (TST) is a successful theory for understanding many different types of reactions, but its application to mineral-water systems has not been successful, especially as the system approaches saturation with respect to a rate-limiting phase. A number of investigators have proposed alternate frameworks for using the kinetic rate data to construct models of dissolution, including Truesdale (Aquat Geochem, 2015; this issue). This alternate approach has been resisted, in spite of self-evident discrepancies between TST expectations and the data. The failure of TST under certain circumstances is a result of the presence of metastable intermediaries or reaction layers that form on the surface of reacting solids, and these phenomena are not anticipated by the current theory. Furthermore, alternate approaches, such as the shrinking object model advocated by Truesdale, represent a potentially important avenue for advancing the science of dissolution kinetics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Understanding the Cathode Electrochemistry of Humidified Solid‐State Lithium‐Oxygen Batteries

Lithium-oxygen batteries (LOBs) possess a high theoretical energy density, making them potential candidates for next-generation energy storage. However, challenges such as reactive oxygen species-induced component degradation hinder their practical use. Inorganic solid-state electrolytes offer an alternative to degradation-prone aprotic electrolytes, while also protecting lithium anodes from potential atmospheric reactants. Here, this study explores the cathode electrochemistry of solid-state LOBs using humidified oxygen, which forms an aqueous catholyte during initial cycling, thereby improving cathode-electrolyte contact. To quantitatively analyze the cathode electrochemistry, a ‘Humidity-Incorporated’ Differential Electrochemical Gas Monitoring System (HiDEMS) is developed to control humidity and monitor gas consumption and evolution in real time. When studying a Li-O 2 cell that employs a NASICON-type Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP) solid electrolyte and a porous carbon cathode, a shift in discharge products from Li 2 O 2 to LiOH is observed over repeated cycles. While Li 2 O 2 evolves O 2 during charging, LiOH oxidation leads to minimal O 2 release and increased CO 2 production, originating from oxidation of carbon electrodes. Further, dissolution of Al and P from LATP is observed, likely driven by the formation of the alkaline catholyte. The findings highlight the need for carbon-free cathode materials and more stable solid-state conductors to minimize side reactions and improve rechargeability in humidified solid-state Li-O 2 batteries.

LATP degradation↗

Dissolution-Assisted Pattern Formation During Olivine Carbonation

Olivine and pyroxene bearing rocks in the oceanic crust react with hydrothermal fluids producing changes in the physical characteristics and behaviors of the altered rocks. Notably, these reactions tend to increase solid volume, reducing pore volume, permeability and available reactive surface area; yet, entirely hydrated and/or carbonated rocks are commonly observed in the field. We investigate the evolution of porosity and permeability of fractured dunites reacted with CO 2 -rich solutions in laboratory experiments. The alteration of crack surfaces changes the mechanical and transport properties of the bulk samples. Analysis of three-dimensional microstructural data shows that although precipitation of secondary minerals causes the total porosity of the sample to decrease, an interconnected network of porosity is maintained through channelized dissolution and coupled carbonate precipitation. Lastly, the observed microstructure appears to be the result of chemo-mechanical coupling, which may provide a mechanism of porosity maintenance without the need to invoke reaction-driven cracking.

58 GEOSCIENCES↗

Lithium metal stripping beneath the solid electrolyte interphase

Lithium stripping is a crucial process coupled with lithium deposition during the cycling of Li metal batteries. Lithium deposition has been widely studied, whereas stripping as a subsurface process has rarely been investigated. Here we reveal the fundamental mechanism of stripping on lithium by visualizing the interface between stripped lithium and the solid electrolyte interphase (SEI). We observed nanovoids formed between lithium and the SEI layer after stripping, which are attributed to the accumulation of lithium metal vacancies. High-rate dissolution of lithium causes vigorous growth and subsequent aggregation of voids, followed by the collapse of the SEI layer, i.e., pitting. We systematically measured the lithium polarization behavior during stripping and find that the lithium cation diffusion through the SEI layer is the rate-determining step. Nonuniform sites on typical lithium surfaces, such as grain boundaries and slip lines, greatly accelerated the local dissolution of lithium. As a result, the deeper understanding of this buried interface stripping process provides beneficial clues for future lithium anode and electrolyte design.

25 ENERGY STORAGE↗

Physiochemical Characterization of Lignocellulosic Biomass Dissolution by Flowthrough Pretreatment

Comprehensive understanding of biomass solubilization chemistry in aqueous pretreatment such as water-only and dilute acid flowthrough pretreatment is of fundamental importance to achieve the goal of valorizing biomass to fermentable sugars and lignin for biofuels production. In this study, poplar wood was flowthrough pretreated by water-only or 0.05% (w/w) sulfuric acid at different temperatures (220-270 °C), flow rate (25 mL/min), and reaction times (8-90 min), resulting in significant disruption of the lignocellulosic biomass. Ion chromatography (IC), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) analysis, and solid state cross-polarization/magic angle spinning (CP/MAS) 13C nuclear magnetic resonance (NMR) spectroscopy were applied to characterize the pretreated biomass whole slurries in order to reveal depolymerization as well as solubilization mechanism and identify unique dissolution structural features during these pretreatments. Results showed temperature-dependent cellulose decrystallization in flowthrough pretreatment. Crystalline cellulose was completely disrupted, and mostly converted to amorphous cellulose and oligomers by water-only operation at 270 °C for 10 min and by 0.05 wt % H2SO4 flowthrough pretreatment at 220 °C for 12 min. Flowthrough pretreatment with 0.05% (w/w) H2SO4 led to a greater disruption of structures in pretreated poplar at a lower temperature compared to water-only pretreatment.

54 ENVIRONMENTAL SCIENCES↗

Integrated modeling of CO2 storage and leakage scenarios including transitions between super- and sub-critical conditions, and phase change between liquid and gaseous CO2

Storage of CO{sub 2} in saline aquifers is intended to be at supercritical pressure and temperature conditions, but CO{sub 2} leaking from a geologic storage reservoir and migrating toward the land surface (through faults, fractures, or improperly abandoned wells) would reach subcritical conditions at depths shallower than 500-750 m. At these and shallower depths, subcritical CO{sub 2} can form two-phase mixtures of liquid and gaseous CO{sub 2}, with significant latent heat effects during boiling and condensation. Additional strongly non-isothermal effects can arise from decompression of gas-like subcritical CO{sub 2}, the so-called Joule-Thomson effect. Integrated modeling of CO{sub 2} storage and leakage requires the ability to model non-isothermal flows of brine and CO{sub 2} at conditions that range from supercritical to subcritical, including three-phase flow of aqueous phase, and both liquid and gaseous CO{sub 2}. In this paper, we describe and demonstrate comprehensive simulation capabilities that can cope with all possible phase conditions in brine-CO{sub 2} systems. Our model formulation includes: (1) an accurate description of thermophysical properties of aqueous and CO{sub 2}-rich phases as functions of temperature, pressure, salinity and CO{sub 2} content, including the mutual dissolution of CO{sub 2} and H{sub 2}O; (2) transitions between super- and subcritical conditions, including phase change between liquid and gaseous CO{sub 2}; (3) one-, two-, and three-phase flow of brine-CO{sub 2} mixtures, including heat flow; (4) non-isothermal effects associated with phase change, mutual dissolution of CO{sub 2} and water, and (de-) compression effects; and (5) the effects of dissolved NaCl, and the possibility of precipitating solid halite, with associated porosity and permeability change. Applications to specific leakage scenarios demonstrate that the peculiar thermophysical properties of CO{sub 2} provide a potential for positive as well as negative feedbacks on leakage rates, with a combination of self-enhancing and self-limiting effects. Lower viscosity and density of CO{sub 2} as compared to aqueous fluids provides a potential for self-enhancing effects during leakage, while strong cooling effects from liquid CO{sub 2} boiling into gas, and from expansion of gas rising towards the land surface, act to self-limit discharges. Strong interference between fluid phases under three-phase conditions (aqueous - liquid CO{sub 2} - gaseous CO{sub 2}) also tends to reduce CO{sub 2} fluxes. Feedback on different space and time scales can induce non-monotonic behavior of CO{sub 2} flow rates.

54 ENVIRONMENTAL SCIENCES↗

Transformation of ferrihydrite in the presence or absence of trace Fe(II): The effect of preparation procedures of ferrihydrite

Two-line ferrihydrite was prepared by two different procedures. In procedure 1, which is widely used, ferrihydrite (named as ferrihydrite-1) was prepared by droping NaOH solution into Fe(III) solution. In procedure 2, which is rarely reported, ferrihydrite (named as ferrihydrite-2) was prepared by adding Fe(III) and NaOH solutions into a certain volume of water simultaneously. The results showed that mixing procedures of Fe(III) and alkaline were critical in the sub-microstructures and the conversion mechanisms of ferrihydrites in the presence or absence of trace Fe(II). The sub-microstructure of ferrihydrite-1 favored the mechanism of its dissolution re-crystallization and hematite nanoparticles with rough surface were obtained. The sub-microstructure of ferrihydrite-2 favored the solid state transformation from ferrihydrite to hematite and hematite nanoparticles with smooth surface were formed. These research results will be helpful for us to control the synthesis of hematite nanoparticles with different surface state. - Graphical abstract: Ferrihydrites prepared by mixing Fe{sup 3+} and NaOH solutions according to different procedures can rapidly transform into hematite particles with different surface structures in the presence of trace Fe(II).

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Alcove formation in dissolving cliffs driven by density inversion instability

We demonstrate conditions that give rise to cave-like features commonly found in dissolving cliffsides with a minimal two-phase physical model. Alcoves that are wider at the top and tapered at the bottom, with sharp-edged ceilings and sloping floors, are shown to develop on vertical solid surfaces dissolving in aqueous solvents. As evident from descending plumes, sufficiently large indentations evolve into alcoves as a result of the faster dissolution of the ceiling due to a solutal Rayleigh–Bénard density inversion instability. In contrast, defects of size below the boundary layer thickness set by the critical Rayleigh number smooth out, leading to stable planar interfaces. Furthermore, the ceiling recession rate and the alcove opening area evolution are shown to be given to first-order by the critical Rayleigh number. By tracking passive tracers in the fluid phase, we show that the alcoves are shaped by the detachment of the boundary layer flow and the appearance of a pinned vortex at the leading edge of the indentations. The attached boundary layer past the developing alcove is then found to lead to rounding of the other sides and the gradual sloping of the floor.

58 GEOSCIENCES↗