Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SWEEP FREQUENCY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

The Influence of Sweep on the Aerodynamic Loading of an Oscillating NACA0012 Airfoil

The effect of sweep on the dynamic response of the NACA 0012 airfoil was investigated. Unsteady chordwise distributed pressure data were obtained from a tunnel spanning wing equipped with 21 single surface transducers (13 on the suction side and 8 on the pressure side of the airfoil). The pressure data were obtained at pitching amplitudes of 8 and 10 degrees over a tunnel Mach number range of 0.10 to 0.46 and a pitching frequency range of 2.5 to 10.6 cycles per second. The wing was oscillated in the unswept and swept positions about the quarter-chord pivot axis relative to mean incidence angle settings of 0, 9, 12, and 15 degrees. A compilation of all the response data obtained during the test program is presented. These data are in the form of normal force, chord force, lift force, pressure drag, and moment hysteresis loops derived from chordwise integrations of the unsteady pressure distributions. The hysteresis loops are organized in two main sections. In the first section, the loop data are arranged to show the effect of sweep (lambda = 0 and 30 deg) for all available combinations of mean incidence angle, pitching amplitude, reduced frequency, and chordwise Mach number. The second section shows the effect of chordwise Mach number (MC = 0.30 and MC = 0.40) on the swept wing response for all available combinations of mean incidence angle, pitching amplitude, and reduced frequency.

St.hilaire, A. O.↗
DOE OSTI2015

SU-D-210-06: Feasibility for Monitoring the Head of the Pancreas Motion Through a Surrogate Using Ultrasound During Radiation Therapy Delivery

Purpose: Substantial target motion during the delivery of radiation therapy (RT) for pancreatic cancer is well recognized as a major limiting factor on RT effectiveness. The aim of this work is to monitor intra-fractional motion of the pancreas using ultrasound during RT delivery. Methods: Transabdominal Ultrasound B-mode images were collected from 5 volunteers using a research version of the Clarity Autoscan System (Elekta). The autoscan transducer with center frequency of 5 MHz was utilized for the scans. Imaging parameters were adjusted to acquire images at the desired depth with good contrast and a wide sweep angle. Since well-defined boundaries of the pancreas can be difficult to find on ultrasound B-mode images, the portal vein was selected as a surrogate for motion estimation of the head of the pancreas. The selection was due to its anatomical location posterior to the neck of the pancreas and close proximity to the pancreas head. The portal vein was contoured on the ultrasound images acquired during simulation using the Clarity Research AFC Workstation software. Volunteers were set up in a similar manner to the simulation for their monitoring session and the ultrasound transducer was mounted on an arm fixed to the couch. A video segment of the portal vein motion was captured. Results: The portal vein was visualized and segmented. Successful monitoring sessions of the portal vein were observed. In addition, our results showed that the ultrasound transducer itself reduces breathing related motion. This is analogous to the use of a compression plate to suppress respiration motion during thorax or abdominal irradiation. Conclusion: We demonstrate the feasibility of tracking the pancreas through the localization of the portal vein using abdominal ultrasound. This will allow for real-time tracking of the intra-fractional motion to justify PTV-margin and to account for unusual motions, thus, improving normal tissue sparing. This research was funding in part by Elekta Inc.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1978

Model verification of large structural systems

A computer program for the application of parameter identification on the structural dynamic models of space shuttle and other large models with hundreds of degrees of freedom is described. Finite element, dynamic, analytic, and modal models are used to represent the structural system. The interface with math models is such that output from any structural analysis program applied to any structural configuration can be used directly. Processed data from either sine-sweep tests or resonant dwell tests are directly usable. The program uses measured modal data to condition the prior analystic model so as to improve the frequency match between model and test. A Bayesian estimator generates an improved analytical model and a linear estimator is used in an iterative fashion on highly nonlinear equations. Mass and stiffness scaling parameters are generated for an improved finite element model, and the optimum set of parameters is obtained in one step.

Lee, L. T.↗
NASA NTRS2003

Laser Velocimeter for Studies of Microgravity Combustion Flowfields

A velocimeter was developed based on modulated filtered Rayleigh scattering (MFRS). The MFRS velocimeter was successfully demonstrated by making one-component velocity measurements in a supersonic expansion using molecular Rayleigh scattering in a jet of N2. These measurements were made in a sweep mode where the Rayleigh scattered profile is cross-correlated with absorption in a static cell to determine velocity. To improve temporal resolution the frequency-locked mode of operation was developed, with an in-situ referencing scheme to compensate for signal fluctuations arising from density variations in the probe volume. Spectroscopic grade (i.e. continuously tunable, single-mode) laser sources with high power (greater than 100 mW) are not commercially available at the wavelength of interest (780 nm). We developed an all-solid-state system with a low power (approximately 10 mW) spectroscopic grade laser source in a Littrow cavity is amplified by a broad-area diode laser. We have demonstrated that the slaved output tracks the injected input but have not yet demonstrated power gain by the end of the grant period.

Varghese, Philip L.↗
NASA NTRS2004

Improving Rotor-Stator Interaction Noise Code Through Analysis of Input Parameters

There are two major sources of aircraft noise. The first is from the airframe and the second is from the engines. The focus of the acoustics branch at NASA Glenn is on the engine noise sources. There are two major sources of engine noise; fan noise and jet noise. Fan noise, produced by rotating machinery of the engine, consists of both tonal noise, which occurs at discrete frequencies, and broadband noise, which occurs across a wide range of frequencies. The focus of my assignment is on the broadband noise generated by the interaction of fan flow turbulence and the stator blades. such as the sweep and stagger angles and blade count, as well as the flow parameters such as intensity of turbulence in the flow. The tool I employed in this work is a computer program that predicts broadband noise from fans. The program assumes that the complex shape of the curved blade can be represented as a single flat plate, allowing it to use fairly simple equations that can be solved in a reasonable amount of time. While the results from such representation provided reasonable estimates of the broadband noise levels, they did not usually represent the entire spectrum accurately. My investigation found that the discrepancy between data and theory can be improved if the leading edge and the trailing edge of the blade are treated separately. Using this approach, I reduced the maximum error in noise level from a high of 30% to less than 5% for the cases investigated. Detailed results of this investigation will be discussed at my presentation. The objective of this study is to investigate the influence of geometric parameters

Unton, Timothy J.↗
NASA NTRS2011

Study of Near-Stall Flow Behavior in a Modern Transonic Fan with Composite Sweep

Detailed flow behavior in a modern transonic fan with a composite sweep is investigated in this paper. Both unsteady Reynolds-averaged Navier-Stokes (URANS) and Large Eddy Simulation (LES) methods are applied to investigate the flow field over a wide operating range. The calculated flow fields are compared with the data from an array of high-frequency response pressure transducers embedded in the fan casing. The current study shows that a relatively fine computational grid is required to resolve the flow field adequately and to calculate the pressure rise across the fan correctly. The calculated flow field shows detailed flow structure near the fan rotor tip region. Due to the introduction of composite sweep toward the rotor tip, the flow structure at the rotor tip is much more stable compared to that of the conventional blade design. The passage shock stays very close to the leading edge at the rotor tip even at the throttle limit. On the other hand, the passage shock becomes stronger and detaches earlier from the blade passage at the radius where the blade sweep is in the opposite direction. The interaction between the tip clearance vortex and the passage shock becomes intense as the fan operates toward the stall limit, and tip clearance vortex breakdown occurs at near-stall operation. URANS calculates the time-averaged flow field fairly well. Details of measured RMS static pressure are not calculated with sufficient accuracy with URANS. On the other hand, LES calculates details of the measured unsteady flow features in the current transonic fan with composite sweep fairly well and reveals the flow mechanism behind the measured unsteady flow field.

Hah, Chunill↗
DOE OSTI2021

Loss channels affecting lithium niobate phononic crystal resonators at cryogenic temperature

Here, we investigate the performance of microwave-frequency phononic crystal resonators fabricated on thin-film lithium niobate for integration with superconducting quantum circuits. For different design geometries at millikelvin temperatures, we achieve mechanical internal quality factors Qi above 10 5 –10 6 at high microwave drive power, corresponding to 5×10 6 phonons inside the resonator. By sweeping the defect size of resonators with identical mirror cell designs, we are able to indirectly observe signatures of the complete phononic bandgap via the resonators' internal quality factors. Examination of quality factors' temperature dependence shows how superconducting and two-level system (TLS) loss channels impact device performance. Finally, we observe an anomalous low-temperature frequency shift consistent with resonant TLS decay and find that the material choice can help to mitigate these losses.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2013

Probing the local surface potential and quantum capacitance in single and multi-layer graphene

We report on local measurements of the surface potential and quantum capacitance in single layer graphene as well as multilayers thereof as a function of the carrier density by using frequency-modulated Kelvin probe force microscopy. We find excellent agreement to tight-binding calculations reported for graphene monolayers and extract the minimum quantum capacitance from density sweeps at room temperature. The surface potential of graphene multilayers is found to depend linearly on the carrier density, which suggests treating them as two-dimensional electron gases. In addition, we demonstrate that the simultaneously detected second harmonic of the Kelvin modulation, proportional to |∂{sup 2}C/∂z{sup 2}|, is directly sensitive to local changes in the quantum capacitance of graphene.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2016

A source-synchronous filter for uncorrelated receiver traces from a swept-frequency seismic source

We have developed a novel algorithm to reduce noise in signals obtained from swept-frequency sources by removing out-of-band external noise sources and distortion caused from unwanted harmonics. The algorithm is designed to condition nonstationary signals for which traditional frequency-domain methods for removing noise have been less effective. The source synchronous filter (SSF) is a time-varying narrow band filter, which is synchronized with the frequency of the source signal at all times. Because the bandwidth of the filter needs to account for the source-to-receiver propagation delay and the sweep rate, SSF works best with slow sweep rates and moveout-adjusted waveforms to compensate for source-receiver delays. The SSF algorithm was applied to data collected during a field test at the University of California Santa Barbara’s Garner Valley downhole array site in Southern California. At the site, a 45 kN shaker was mounted on top of a one-story structure and swept from 0 to 10 Hz and back over 60 s (producing useful seismic waves greater than 1.6 Hz). The seismic data were captured with small accelerometer and geophone arrays and with a distributed acoustic sensing array, which is a fiber-optic-based technique for the monitoring of elastic waves. The result of the application of SSF on the field data is a set of undistorted and uncorrelated traces that can be used in different applications, such as measuring phase velocities of surface waves or applying convolution operations with the encoder source function to obtain traveltimes. Lastly, the results from the SSF were used with a visual phase alignment tool to facilitate developing dispersion curves and as a prefilter to improve the interpretation of the data.

58 GEOSCIENCES↗
NASA NTRS1960

Free-Spinning-Tunnel Investigation of a 1/20-Scale Model of an Unswept-Wing Jet-Propelled Trainer Airplane

A flutter analysis employing the kernel function for three- dimensional, subsonic, compressible flow is applied to a flutter-tested tail surface which has an aspect ratio of 3.5, a taper ratio of 0.15, and a leading-edge sweep of 30 deg. Theoretical and experimental results are compared at Mach numbers from 0.75 to 0.98. Good agreement between theoretical and experimental flutter dynamic pressures and frequencies is achieved at Mach numbers to 0.92. At Mach numbers from 0.92 to 0.98, however, a second solution to the flutter determinant results in a spurious theoretical flutter boundary which is at a much lower dynamic pressure and at a much higher frequency than the experimental boundary.

Bowman, James S., Jr.↗
NASA NTRS1960

Subsonic Kernel-Function Flutter Analysis of a Highly Tapered Tail Surface and Comparison with Experimental Results

A flutter analysis employing the kernel function for three-dimensional, subsonic, compressible flow is applied to a flutter-tested tail surface which has an aspect ratio of 3.5, a taper ratio of 0.15, and a leading-edge sweep of 30 deg. Theoretical and experimental results are compared at Mach numbers from 0.75 to 0.98. Good agreement between theoretical and experimental flutter dynamic pressures and frequencies is achieved at Mach numbers to 0.92. At Mach numbers from 0.92 to 0.98, however, a second solution to the flutter determinant results in a spurious theoretical flutter boundary which is at a much lower dynamic pressure and at a much higher frequency than the experimental boundary.

Walberg, Gerald D.↗
NASA NTRS2002

An Implementation of a Tracking Filter

For Goddard's new Matlab-based data analysis system, a Hilbert transform is used to generate a quadrature signal directly from the COLA signal. This differs from the usual practice of synthesizing the sine and cosine components after determining the sweep characteristics from the COLA signal. The original and quadrature signals are in turn mixed with the signal to be analyzed and then filtered to determine the frequency spectrum. This new technique appears to be more accurate in determining frequency and is insensitive to variations in COLA amplitude.

Worth, Daniel B.↗
DOE OSTI2016

Genome-wide selective sweeps and gene-specific sweeps in natural bacterial populations

Multiple models describe the formation and evolution of distinct microbial phylogenetic groups. These evolutionary models make different predictions regarding how adaptive alleles spread through populations and how genetic diversity is maintained. Processes predicted by competing evolutionary models, for example, genome-wide selective sweeps vs gene-specific sweeps, could be captured in natural populations using time-series metagenomics if the approach were applied over a sufficiently long time frame. Direct observations of either process would help resolve how distinct microbial groups evolve. Using a 9-year metagenomic study of a freshwater lake (2005–2013), we explore changes in single-nucleotide polymorphism (SNP) frequencies and patterns of gene gain and loss in 30 bacterial populations. SNP analyses revealed substantial genetic heterogeneity within these populations, although the degree of heterogeneity varied by >1000-fold among populations. SNP allele frequencies also changed dramatically over time within some populations. Interestingly, nearly all SNP variants were slowly purged over several years from one population of green sulfur bacteria, while at the same time multiple genes either swept through or were lost from this population. Furthermore, these patterns were consistent with a genome-wide selective sweep in progress, a process predicted by the ‘ecotype model’ of speciation but not previously observed in nature. In contrast, other populations contained large, SNP-free genomic regions that appear to have swept independently through the populations prior to the study without purging diversity elsewhere in the genome. Finally, evidence for both genome-wide and gene-specific sweeps suggests that different models of bacterial speciation may apply to different populations coexisting in the same environment.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

The Dynamics of Ions on Phased Radio-frequency Carpets in High Pressure Gases and Application for Barium Tagging in Xenon Gas Time Projection Chambers

Radio-frequency (RF) carpets with ultra-fine pitches are examined for ion transport in gases at atmospheric pressures and above. We develop new analytic and computational methods for modeling RF ion transport at densities where dynamics are strongly influenced by buffer gas collisions. An analytic description of levitating and sweeping forces from phased arrays is obtained, then thermodynamic and kinetic principles are used to calculate ion loss rates in the presence of collisions. This methodology is validated against detailed microscopic SIMION simulations. We then explore a parameter space of special interest for neutrinoless double beta decay experiments: transport of barium ions in xenon at pressures from 1 to 10 bar. Our computations account for molecular ion formation and pressure dependent mobility as well as finite temperature effects. We discuss the challenges associated with achieving suitable operating conditions, which lie beyond the capabilities of existing devices, using presently available or near-future manufacturing techniques.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Computational Characterization and Boundary Condition Models of a Jet Interaction Fluidic Oscillator

Fluidically oscillating jet actuators that generate sweeping jets when supplied with a pressurized fluid have been used to mitigate separation and reduce drag in a range of flow control applications. Their implementation in future flight vehicles would require fundamental understanding and accurate predictive techniques of the physics of their internal flow and jet formation. The present investigations focus on high-fidelity, time-accurate simulations to characterize the flow physics of the actuator in quiescent conditions. An important element of the present simulations is to demonstrate the ability of the computational fluid dynamics (CFD) solver to predict the jet characteristics and provide a basis for the development of improved boundary conditions (BC) without entirely resolving the geometrical features of the fluidic device. The CFD-predicted oscillation frequencies of the engendered jets were found to be in excellent agreement with experiments, even on two-dimensional meshes. The study revealed that three-dimensional simulations are required to capture some of the flow features of the sweeping jet such as the double peak in time-averaged velocity distributions downstream of the actuator’s orifice that were measured in experiments. Furthermore, several approaches for modeling the actuator were implemented and assessed in quiescent conditions. The evaluation of a boundary condition at the device throat, based on the phase-averaged flow variables, provides the basis for devising surface-based boundary conditions. The influence and necessity of including turbulent characteristics as part of the boundary conditions have also been identified.

42 ENGINEERING↗
NASA NTRS1972

Dynamic stability derivatives at angles of attack from minus 5 deg to 90 deg for a variable-sweep fighter configuration with twin vertical tails

An investigation was conducted in the Langley full-scale tunnel to determine the dynamic stability derivatives in pitch, roll, and yaw over an angle-of-attack range of -5 deg to 90 deg for a variable-sweep fighter configuration with twin vertical tails. The study consisted of forced-oscillation tests of a 1/10-scale model of the airplane at a Reynolds number of 0.4 million based on the reference wing mean aerodynamic chord. Tests were conducted for wing sweep angles of 22 deg, 35 deg, 50 deg, and 68 deg, and the effects of the vertical and horizontal tails, wing leading-edge slats, nose-mounted canards, and frequency of the oscillation were also evaluated.

Grafton, S. B.↗
NASA NTRS1988

Effect of large amplitude pitching motions on the unsteady aerodynamic characteristics of flat-plate wings

Large-amplitude unsteady motion effects on the aerodynamic force and stability characteristics of flat-plate wings were investigated in a wind tunnel for the cases of two delta wings with respective leading edge sweeps of 70 and 45 deg, and a rectangular wing whose aspect ratio was equal to that of the 70-deg delta wing. Attention was given to the effects of reduced frequency and mean angle of attack. It is found that lags in vortex burst location and separation/reattachment of flow on the upper surface of the wing produced large overshoots and hysteresis loops in normal force and pitching moment coefficients that were a strong function of mean oscillation angle and reduced frequency.

Brandon, Jay M.↗