Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STYRENE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Side-Chain Nanophase Separation Broadens the Double-Gyroid Stability Window in PS–PODMA Diblock Copolymers

Expanding access to bicontinuous network phases in block copolymers remains an important challenge because the double gyroid (DG) phase is usually stable only within a narrow composition window in conventional diblock copolymers. Here, we show that poly(styrene-block-octadecyl methacrylate) (PS-b-PODMA) exhibits an unusually broad DG window. Small-angle X-ray scattering measurements across a wide composition range reveal lamellar and hexagonally packed cylindrical phases at higher polystyrene fractions. In contrast, the DG phase appears over 0.22 ≤ fPS ≤ 0.35, with DG/BCC and DG/HEX coexistence near fPS = 0.18 and 0.40, respectively. This broad DG window is much wider than those reported for neat diblock copolymers and is not readily explained by conformational asymmetry alone. Wide-angle X-ray scattering detects a characteristic signature of nanophase separation within the PODMA-rich domains, indicating that side-chain ordering introduces an additional internal length scale. These results suggest that hierarchical side-chain nanophase separation modifies packing frustration and curvature selection, thereby broadening DG stability and providing a new molecular design strategy for stabilizing complex network morphologies.

Seko, Tamio↗

Interfacial Effects on the Dielectric Properties of Elastomer Composites and Nanocomposites

Elastomer-based composites and nanocomposites are discussed, with the emphasis on the filler and interfacial effects on their dynamics, and the resulting manifestation in their macroscopic dielectric or mechanical response. Specifically, selected polydimethylsiloxane (PDMS)/barium-titanate and styrene-butadiene rubber (SBR)/graphene oxide nanocomposites are discussed, as examples where controlled spatial distribution of filler (structured composites) gives rise to significantly different dielectric and thermomechanical behaviors. Also, ethylene–propylene–diene (EPDM)/carbon black (CB) composites are presented, as examples of systems that exhibit an abnormal temperature dependence of dielectric relaxation; and this response is discussed in the context of CB cluster polarization and quantified through a simple scaling model of the same. Finally, multi-filler EPDM/CB/ceramic elastomer nanocomposites are discussed, as examples of systems with antagonistic interfacial effects between conductive and dielectric fillers, as well as with strong interphase responses that can overwhelm the dielectric contributions from the fillers; in these systems, interphasial responses result in counter-intuitive dielectric behaviors and in strong deviations from standard design principles typically employed in the design of dielectric composite systems.

Li, Bo↗

Comparison of dialysis and solid-phase extraction for isolation and concentration of dissolved organic matter prior to Fourier transform ion cyclotron resonance mass spectrometry

We compare two methods, solid-phase extraction (SPE) and dialysis, commonly used for extraction and concentration of dissolved organic matter (DOM) prior to molecular characterization by electrospray ionization (ESI) and ultrahigh-resolution Fourier transform ion cyclotron resonance mass spectrometry. Spectra of DOM samples from Minnesota and Sweden peatlands that were extracted with styrene divinyl benzene polymer SPE sorbents included ions with formulas that had higher oxygen to carbon (O/C) ratios than spectra of DOM from the same samples after de-salting by dialysis. The SPE method was not very effective in extracting several major classes of DOM compounds that had high ESI efficiencies, including carboxylic acids and organo-sulfur compounds, and that out-competed other less-functionalized compounds (e.g., carbohydrates) for charge in the ESI source. Here, the large abundance of carboxylic acids in the dialysisextracted DOM, likely the result of in situ microbial production, makes it difficult to see other (mainly hydrophilic) compounds with high O/C ratios. Our results indicate that, while dialysis is generally preferable for the isolation of DOM, for samples with high microbial inputs, the use of both isolation methods is recommended for a more accurate molecular representation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Block copolymer-mediated synthesis of TiO2/RuO2 nanocomposite for efficient oxygen evolution reaction

Abstract An amphiphilic block copolymer, poly (styrene-2-polyvinyl pyridine-ethylene oxide), was used as a structure-directing and stabilizing agent to synthesize TiO 2 /RuO 2 nanocomposite. The strong interaction of polymers with metal precursors led to formation of a porous heterointerface of TiO 2 /RuO 2 . It acted as a bridge for electron transport, which can accelerate the water splitting reaction. Scanning electron microscopy, energy-dispersive X -ray spectroscopy, transmission electron microscopy, and X -ray diffraction analysis of TiO 2 /RuO 2 samples revealed successful fabrication of TiO 2 /RuO 2 nanocomposites. The TiO 2 /RuO 2 nanocomposites were used to measure electrochemical water splitting in three-electrode systems in 0.1-M KOH. Electrochemical activities unveil that TiO 2 /RuO 2 -150 nanocomposites displayed superior oxygen evolution reaction activity, having a low overpotential of 260 mV with a Tafel slope of 80 mVdec −1 . Graphical abstract

36 MATERIALS SCIENCE↗

Effect of Vertical Strut Arrangements on Compression Characteristics of 3D Printed Polymer Lattice Structures: Experimental and Computational Study

This paper discusses the behavior of the three-dimensional (3D) printed polymer lattice core structures during compressive deformation, by both physical testing and computer modeling. Four lattice configurations based on the body-centered cubic (BCC) unit cell were selected to investigate the effect of vertical strut arrangements on stiffness, failure load, and energy absorption per unit mass or the specific energy absorption (SEA). The basic BCC unit cell consists of struts connecting the body center to the corners of the cube. Three variations in the BCC configuration considered in this study are (1) BCCV, with vertical members connecting all nodes of the lattice, (2) BCCA, with vertical members in alternating layers of the lattice, and (3) BCCG, with a gradient in the number of vertical members increasing from none at the top layer to all vertical members at the bottom layer. The unit cell dimensions were 5 mm × 5 mm × 5 mm with strut diameter of 1 mm. The lattice was assembled with 5 cells in the x and y directions and 4 cells in the z direction. Specimens were first made by 3D printing by using a fused deposition modeling printer with acrylonitrile–butadiene–styrene thermoplastic. Specimens were then tested under compression in the z direction under quasi-static conditions. Finite element analysis was used to model the compressive behavior of the different lattice structures. Results from both experiments and finite element models show that the strength of the lattice structures is greater when vertical members are present, and the SEA depends on the lattice geometry and not its mass.

36 MATERIALS SCIENCE↗

Tailoring the Properties of Calcium Aluminate Macro-Defect-Free Cements: From Brittle to Ductile Behavior

Cementitious macro-defect-free (MDF) materials can be obtained processing a mixture of a water-soluble polymer, namely polyvinyl alcohol (PVA) and the calcium aluminate cement. Based on process techniques typical of plastics, the MDF products can be obtained in complex forms and, thanks to the reduced water to cement ratio, w/c, their strength is very high compared to standard cements. However, these materials show both the sensitivity typical of water-soluble polymers, presenting a low glass transition temperature (T{sub g}), and the brittle behavior typical of ceramic materials and therefore low toughness. The aim of this work is to modify the mechanical properties of MDF cements by tuning their unacceptable brittle behavior. Water solution of carboxylate styrene butadiene rubber is used as reactive additives, and different mixture formulations are tested changing the rubber-like content both with respect to the fixed water content and PVA amounts. It is shown that the modifications of the organic phase imply small or negligible effects on paste formation of different recipes as detected by the torque–time responses. From flexural and fracture toughness tests, a wide range of responses was observed, and depending on the particular recipe, the mechanical behavior can be tuned from a brittle to a ductile behavior.

36 MATERIALS SCIENCE↗

Characterization of ZnO Nanoparticles using Superconducting Tunnel Junction Cryodetection Mass Spectrometry

Zinc oxide (ZnO) nanoparticles coated with either n-octylamine (OA) or α-amino poly(styrene-co-acrylonitrile) (PSAN) ligands (L) have been analyzed using laser desorption/ionization and matrix assisted laser desorption/ionization (MALDI) time-of-flight (TOF) superconducting tunnel junction (STJ) cryodetection mass spectrometry. STJ cryodetection has the advantage of high m/z detection and allows for the determination of average molecular weights and dispersities for 500–600 kDa ZnO-L nanoparticles. The ability to detect the relative energies deposited into the STJs has allowed for investigation of ZnO-L metastable fragmentation. ZnO-L precursor ions gain enough internal energy during the MALDI process to undergo metastable fragmentation in the flight tube. These fragments produced a lower energy peak, which was assigned as ligand-stripped ZnO cores whereas the individual ligands were at too low of an energy to be observed. From these STJ energy resolved peaks, the average weight percentage of inorganic material making up the nanoparticle was determined, where ZnO-OA and ZnO-PSAN nanoparticles are comprised of ~62% and ~68% wt ZnO, respectively. In one example, grafting densities were calculated based on the metastable fragmentation of ligands from the core to be 16 and 1.1 nm{sup –2} for ZnO-OA and ZnO-PSAN, respectively, and compared with values determined by thermogravimetric analysis (TGA) and transmission electron microscopy (TEM). .

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Determination of melt processing conditions for high performance amorphous thermoplastics for large format additive manufacturing

As the application space for large-scale 3D printed components continues to grow, it is necessary to identify appropriate processing conditions for high-performance thermoplastics on large format Additive Manufacturing (LFAM) systems. This study compares the rheological behavior of a high-performance thermoplastic, polyphenylsulfone (PPSU), with that of a commonly used low-temperature polymer, acrylonitrile butadiene styrene (ABS), to identify suitable processing conditions for large format AM systems. The linear viscoelastic properties (complex viscosity, storage modulus, loss modulus, and tan delta) of these materials are evaluated as a function of temperature, angular frequency, and carbon fiber content. Over the range of frequencies of interest to LFAM (10–100 rad/s), ABS behaves more like an elastic solid whereas PPSU behaves more like a viscous liquid. Here, the addition of 20–35% by weight of carbon fiber increased the shear thinning effect of both thermoplastics, showing a potential variation of 2–3 x over the range of expected LFAM extrusion shear rates (10–100 s –1 ).

36 MATERIALS SCIENCE↗

Controlling substrate temperature with infrared heating to improve mechanical properties of large-scale printed parts

Additively manufactured parts made with polymer extrusion techniques can be 50-75% weaker in the z-direction (across layers) than in the x- and y-directions. This has been attributed to poor mobility of polymer chains and a low degree of entanglement across a cold deposition interface. This is particularly a challenge when printing large-scale parts, such as with the Big Area Additive Manufacturing (BAAM) system, because layer times can exceed several minutes. The current work presents a method for controlling the temperature of the substrate material on the BAAM just prior to deposition using infrared heating lamps. Additionally, long layer times were simulated by actively cooling the material following deposition of each layer. The effect of substrate temperature on the z-direction mechanical properties of 20% carbon fiber reinforced acrylonitrile butadiene styrene (ABS) was measured for an initial temperature ranging from 50 °C to 150 °C and a preheated temperature ranging from 150 °C to 220 °C. Infrared preheating proved to be very effective when applied to substrates that had cooled considerably, almost doubling the tensile strength and increasing the fracture toughness by a factor of 7x.

36 MATERIALS SCIENCE↗

High-performance molded composites using additively manufactured preforms with controlled fiber and pore morphology

Here, large-scale multimaterial preforms produced by additive manufacturing (AM) underwent compression molding (CM) to produce high-performance thermoplastic composites reinforced with short carbon fibers. AM and CM techniques were integrated to control the fiber orientation (microstructure) and to reduce void content for the improved mechanical performance of the composite. The new integrated manufacturing technique is termed “additive manufacturing-compression molding” (AM-CM). For the present study, the most common materials were used for large-scale printing, i.e., acrylonitrile butadiene styrene (ABS), carbon fiber (CF)–filled ABS (CF/ABS) and glass fiber (GF)–filled ABS (GF/ABS). Three different manufacturing processes; (a) AM (b) extrusion compression molding (ECM), and (c) AM-CM were used to prepare four different panel configurations: (1) neat ABS, (2) CF/ABS, (3) overmold (CF/ABS over neat ABS), and (4) sandwich (neat ABS between two CF/ABS layers). The mechanical properties (tensile and flexural strength and modulus, and Izod impact energy) of samples prepared via all three manufacturing processes were compared. X-ray microcomputer tomography was employed to evaluate the fiber orientation distribution and the volumetric porosity content. The preform maintained high fiber alignment (≈ 82% of fibers within the range of 0–20° in the deposition direction), and the volumetric porosity was reduced by 50% from 3.79% to 1.91% after compression. The alignment of long pores along the deposition direction was also observed. The mechanical properties are discussed with correlation to the fiber alignment and void content in the samples. CF/ABS samples prepared by AM-CM showed significant improvement of 11.15%, 35.27%, 28.6%, and 74.3% in the tensile strength, tensile modulus, flexural strength, and flexural modulus, respectively, when compared with samples prepared by ECM. Unique aspects of this study are the demonstration of large-scale multimaterial AM and the use of multimaterials as preforms to make high-performance composites.

36 MATERIALS SCIENCE↗

Characterizing material transitions in large-scale Additive Manufacturing

Integrating Multiple Materials (MM) into large-scale Additive Manufacturing (AM) is a key for various industrial applications wishing to incorporate site-specific properties into geometrically complex designs that are difficult to manufacture with traditional techniques. Printing with multiple materials is typically accomplished by using layers as natural material boundaries, but having the capability to switch between materials within a single layer without pausing would further expand MM possibilities. This study used Cincinnati Incorporated’s Big Area Additive Manufacturing (BAAM) system to explore material transitions with a novel dual-hopper that enables in-situ material blending of a pelletized feedstock. Constructing MM and functionally graded material (FGM) structures requires depositing a specific material composition at a specific geometric location to achieve a desired performance. Furthermore, accurately implementing this with the BAAM’s blended extrusion system requires a thorough understanding of the transition between distinct material compositions. This study characterizes a step-change transition between neat acrylonitrile butadiene styrene (ABS) and carbon fiber-reinforced ABS. Three distinct techniques were compared for analyzing the fiber content, and the transition zone between materials was characterized as a function of transition direction. The transition process was consistent to within 0.7 wt% carbon fiber variation between different layers and prints. The transition between materials was found to be directionally dependent, with ABS to CF/ABS having a transition length of 3.5 m compared to 3.2 m for CF/ABS to ABS. Furthermore, the transition from Material A to Material B was found to be repeatable with a possible variance in transition length of 0.3 m.

36 MATERIALS SCIENCE↗

The impact of infill percentage and layer height in small-scale material extrusion on porosity and tensile properties

We report material extrusion additive manufacturing is prone to introducing porosity within the structure due to the layer-by-layer construction using elliptical beads of material. This open porosity ultimately plays a role in determining the mechanical properties of printed parts. The shape, size, and amount of porosity within a printed part is influenced by a variety of factors, including nozzle diameter, infill percentage, layer height, raster orientation, and print speed. While several studies have investigated these and other parameters’ effects on mechanical performance and porosity, better understanding the interconnected relationships is crucial in balancing the various input parameters to achieve maximum strength. This work initially examined the influence of key print parameters (infill percentage and layer height) on the internal porosity of a printed Acrylonitrile Butadiene Styrene (ABS) part. Then, the print parameters and internal porosity were statistically correlated to final mechanical properties. Porosity was further classified as either open or closed to differentiate between connected voids in the mesostructure from isolated voids within the material itself. Mechanical performance increased with an increasing density and infill percentage, displaying a 224 % increase in elastic modulus and a 150 % increase in ultimate tensile strength. The contribution of layer height was found to be conditional upon the infill percentage.

3D Printing↗

Measuring thermomechanical response of large-format printed polymer composite structures via digital image correlation

Large-format additive manufacturing (LFAM) is a branch of additive manufacturing (AM) research with the ability to create large structures typically measuring several meters in scale. LFAM is advantageous for tooling applications, not only because it offers the ability to create complex geometries not easily made using subtractive manufacturing processes, but the cost savings of pelletized feedstock used by these systems result in larger parts printed at faster speeds than traditional AM systems. Fiber reinforced polymer (FRP) is a commonly used feedstock material in LFAM structures because it reduces the distortion experienced during printing. However, FRP introduces highly anisotropic thermomechanical properties and contributes to a nonhomogeneous microstructure that can result in critical distortion of dimensions during tooling. Measuring the global thermomechanical response of LFAM structures requires a more representative method that accounts for not only anisotropic properties but also the nonhomogeneous nature of the final part. This is where traditional techniques to measure thermomechanical response, such as thermomechanical analysis (TMA), fall short as they assume homogeneity. This study evaluated the coefficient of thermal expansion (CTE) of LFAM structures as measured by TMA as compared to a novel digital image correlation oven (DIC Oven) system. The LFAM structures were made from 20 % by weight carbon fiber reinforced acrylonitrile butadiene styrene (CF-ABS). TMA measurements showed significant variations in CTE across a single LFAM bead, confirming the need for a global technique that captures overall thermomechanical response. The CTE values measured using the DIC Oven compared well to average TMA values obtained from localized measurements across the sample. The DIC Oven was also used to quantify the effects of different layer orientations on thermomechanical properties, which cannot be easily captured using TMA. A predictive model was also developed by using localized TMA values across an LFAM bead to predict the overall thermomechanical response of an LFAM structure.

36 MATERIALS SCIENCE↗

Co-aromatization of olefin and methane over Ag-Ga/ZSM-5 catalyst at low temperature

The massive exploitation of shale gas in the past decade has boosted the production of natural gas and reduced its price dramatically. The methane activation and following conversion into more valuable fuels and chemicals have thus become more and more attractive, while the introduction of hydrocarbons to enhance the methane activation at mild conditions represents a promising approach. In the present work, the co-aromatization of methane with propylene has been studied at 400 °C. The presence of methane would increase the toluene to benzene ratio as well as the average carbon number of the formed liquid aromatic products compared to its propylene alone counterpart. Among the gas products, the formations of C 3 H 8 , C 4 H 8 and C 4 H 10 also get promoted when methane is present. The incorporation of methane into the product molecules is also directly evidenced by the 1 H, 2 D and 13 C NMR spectroscopy of the liquid products obtained from the reaction between propylene (or styrene) and isotope labelled methane. Hydrogen from methane would contribute a large portion of the hydrogen in the product molecules, while the benzylic and aromatic hydrogen sites are favored compared with those on the alkyl side chains. The activation of methane is also observed in the DRIFT spectra when deuterium enriched methane is engaged as the methane source and evidenced by the escalated exothermic feature when olefin aromatization takes place under methane environment. The excellent catalytic performance of Ag-Ga/ZSM-5 might be because of the better dispersion of Ag and Ga on the ZSM-5 surface and moderate amount of strong Brosted and Lewis surface acid sites. All the observations suggest that methane might be activated nonoxidatively and converted into aromatics if suitable catalyst is charged under the assistance of co-existing olefin. In conclusion, the reported synergetic effect could potentially lead to the more economic utilization of abundant natural gas and petrochemical intermediates.

09 BIOMASS FUELS↗

A preliminary regional PBPK model of lung metabolism for improving species dependent descriptions of 1,3-butadiene and its metabolites

1,3-Butadiene (BD), a volatile organic chemical (VOC), is used in synthetic rubber production and other industrial processes. It is detectable at low levels in ambient air as well as in tobacco smoke and gasoline vapors. Inhalation exposures to high concentrations of BD have been associated with lung cancer in both humans and experimental animals, although differences in species sensitivity have been observed. Metabolically active lung cells such as Pulmonary Type I and Type II epithelial cells and club cells (Clara cells) 1 are potential targets of BD metabolite-induced toxicity. Metabolic capacities of these cells, their regional densities, and distributions vary throughout the respiratory tract as well as between species and cell types. Here we present a physiologically based pharmacokinetic (PBPK) model for BD that includes a regional model of lung metabolism, based on a previous model for styrene, to provide species-dependent descriptions of BD metabolism in the mouse, rat, and human. Since there are no in vivo data on BD pharmacokinetics in the human, the rat and mouse models were parameterized to the extent possible on the basis of in vitro metabolic data. Where it was necessary to use in vivo data, extrapolation from rat to mouse was performed to evaluate the level of uncertainty in the human model. A kidney compartment and description of downstream metabolism were also included in the model to allow for eventual use of available urinary and blood biomarker data in animals and humans to calibrate the model for estimation of BD exposures and internal metabolite levels. Results from simulated inhalation exposures to BD indicate that incorporation of differential lung region metabolism is important in describing species differences in pulmonary response and that these differences may have implications for risk assessments of human exposures to BD.

1,3-Butadiene↗

Layered oxide cathode-inspired secondary hard carbon microsphere anode material for high-power and long-life rechargeable batteries

A new anode material that will provide lithium ion (Li-ion) batteries with high energy and power density is urgently needed. In this work, a layered oxide cathode-inspired secondary hard carbon microsphere (CMS) anode material was designed, and exhibited excellent rate performance and long cyclability. Polyacrylonitrile/poly(styrene-co-acrylonitrile) (PAN/SAN) compositions displaying the meatball-like shape of the PAN precursor were carbonized into CMSs having turbostratic microstructures. The CMS carbonized at 1,000°C (CMS1000) displayed high specific capacity at the highest current density of 1,000mAg -1 , i.e., 77.6 % of its average charge capacity at 100 mA g -1 , and considerable cycling retention after 500 cycles, i.e., 83.8 % of the specific capacity at cycle 25. In conclusion, our work demonstrates that the design of new anode materials is a fruitful route to improve commercial Li-ion batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Buried interface modulation via $\mathrm{PEDOT:PSS}$ ionic exchange for the Sn-Pb mixed perovskite based solar cells

To apply Sn-Pb mixed perovskite solar cells for highly efficient single- or multi-junction devices, understanding device-specific buried interfaces is necessary. Poly [3,4-ethylenedioxythiophene]:poly[styrene sulfonate] (PEDOT:PSS) is primarily used as a hole transport layer in Sn-Pb mixed perovskite solar cells. However, the spatial heterogeneity of PEDOT:PSS, caused by its PEDOT-rich and PSS-rich domains, induces many defects at the buried interface in PEDOT:PSS/perovskite, which limits device performance. Here, we present ionic exchange (IE) of PEDOT:PSS via a combination of methylamine iodide (MAI) and dimethyl sulfoxide (DMSO). Through surface analyses and density functional theory (DFT) simulations, we confirm that the IE process preferentially form PEDOT-I and MA-PSS and that PSS-rich domains bind to DMSO. Thus, the spatial separation of PEDOT:PSS is solved, and the exchanged MA + and I - ions serve as a bridge between PEDOT:PSS and the perovskite, leading to improved physical, chemical, and electrical properties of the buried interface. The Sn-Pb mixed perovskite solar cells using IE-PEDOT:PSS achieve an improved efficiency of 21.3% with an open-circuit voltage of 0.85 V and show better long-term stability. Additionally, IE-PEDOT:PSS works effectively in 2-terminal all-perovskite tandem devices, resulting in an improved efficiency of 23.5% and high reproducibility.

14 SOLAR ENERGY↗

Heterogeneous hydroformylation of alkenes by Rh-based catalysts

Heterogeneously catalyzed hydroformylation reactions avert the problems of separation in homogeneous reactions, reduce the discharge of phosphorus-containing wastes, and prevent the loss of precious metals. This review summarizes the developments of catalysts for heterogeneous hydroformylation in the last decade and proposes potential modification methods for future improvements. The hydroformylation properties of different reactants are compared in order to emphasize the fact that various olefins face unique challenges. The hydroformylation of ethylene requires the enhancement of catalytic activity and chemoselectivity, whereas that of propylene needs improvements in both chemoselectivity and regioselectivity. The hydroformylation of longer-chain olefins and styrene seeks further improvement in regioselectivity. The catalytic properties of activity, selectivity, and stability can be tuned through electronic effects (bimetallic effects, phosphine ligands, and single-atom catalysts), steric hindrance (encapsulation structures, diphosphine ligands, and local functional groups), and reaction condition optimization (temperature, pressure, and solvents). Furthermore, the understanding of these effects is critical in future catalyst design for heterogeneous hydroformylation reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗