Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Effect of silicon on ultra-low temperature toughness of Nb–Ti microalloyed cryogenic pressure vessel steels

The effect of Si on the ultra-low temperature toughness of Nb–Ti microalloyed cryogenic pressure vessel steels was investigated by electron back-scattered diffraction and transmission electron microscope with energy dispersive spectroscopy. Equiaxed ferrite and bainite were obtained in the tempered steels with small Si additions. Nanosized Nb–Ti carbides (< 10 nm) were formed in the steel containing 0.05% Si, whereas much coarser carbides (> 30 nm) were found in the steel containing 0.47% Si. The ultra-low temperature toughness of the Nb–Ti microalloyed cryogenic pressure vessel steel was remarkably enhanced by the reduction in the Si content, which was attributed to the pre-existing iron carbide formation before the precipitation of nanosized Nb–Ti carbides during tempering. - Highlights: • Nanosized Nb-Ti carbides formed in the tempered steel with smaller Si addition. • Coarser Nb-Ti carbides formed in the tempered steel with more Si addition. • Pre-existing cememtites provide nucleation sites for Nb-Ti carbide precipitation. • Ultra-low temperature toughness was remarkably enhanced by Si content reduction.

36 MATERIALS SCIENCE↗

Improved the microstructures and properties of M3:2 high-speed steel by spray forming and niobium alloying

The microstructures and properties of spray formed (SF) high-speed steels (HSSs) with or without niobium (Nb) addition were studied. Particular emphasis was placed on the effect of Nb on the solidification microstructures, decomposition of M{sub 2}C carbides, thermal stability and mechanical properties. The results show that spray forming can refine the cell size of eutectic carbides due to the rapid cooling effect during atomization. With Nb addition, further refinement of the eutectic carbides and primary austenite grains are obtained. Moreover, the Nb addition can accelerate the decomposition of M{sub 2}C carbides and increase the thermal stability of high-speed steel, and also can improve the hardness and bending strength with slightly decrease the impact toughness. The high-speed steel made by spray forming and Nb alloying can give a better tool performance compared with powder metallurgy M3:2 and commercial AISI M2 high-speed steels. - Highlights: • Spray forming can effectively refine the microstructure of M3:2 steel. • Niobium accelerates the decomposition of M{sub 2}C carbides. • Niobium increases the hardness and bending strength of spray formed M3:2 steel. • Spray-formed niobium-containing M3:2 steel has the best tool performance.

36 MATERIALS SCIENCE↗

Solar energy protects steels against corrosion: Enhanced protection capability achieved by NiFeOx decorated BiVO4 photoanode

Highlights: • Steel corrosion is inhibited by coupling to irradiated photoanode. • NiFeO{sub x} promotes charge transfer from BiVO{sub 4} to connected steel. • BiVO{sub 4} composite photoanode decreases the self-corrosion potential of 316 steel by 256 mV. - Abstract: Coupling n-type semiconductor photoelectrode with steels provides protection from corrosion for the latter by pumping electrons produced by water oxidation reaction in a sustainable way. Although the concept of the photocathodic protection of steels has been proposed for about two decades, this technique is still far away from practical applications due to the limited protection capability. In this work, we reported that the BiVO{sub 4} photoanode significantly decreases the self-corrosion potential of 316 steel by 166 mV, and the decoration of NiFeO{sub x} films onto BiVO{sub 4} further shifts the self-corrosion potential by ∼90 mV negatively, which exhibits an excellent protection capability. The protection capability of the photoelectrode to steel is limited by the relative position of the Fermi level of the semiconducting material, and confined by the thermodynamics of the surface reactions on the semiconductor-electrolyte interface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of scan rate on the corrosion behavior SS 304 stainless steel in the nanofluid measured by Tafel polarization methods

The Effects of scan rate on the Tafel polarization curve that is obtained to determine corrosion rate are conducted. The tafel polarization curves are obtained at different scan rates for Stainless Steel 304 in nanofluids contain 0.01 gpl nano particle ZrO{sub 2}. The corrosion stainless steel in nanofluid contains adm+0.01 gpl ZrO{sub 2} nanoparticles at different scan rate was performed by Tafel polarization. The results show that according corrosion potential examination of the stainless steel in nanofluid media 0.01gpl ZrO{sub 2} nanoparticle was actively corroded. The value of cathodic Tafel slope stainless steel in nanofluid at different scan rate relatively unchanged after polarization testing. Mean while the value of anodic Tafel slope stainless steel in nanofluid increase at different scan rate. The results of Tafel polarization technique show that corrosion rate of stainless steel in nanofluid increase with increasing scan rate. X ray diffraction examination of stainless steel after Tafel polarization depict that γ Fe phase is major phase in the surface of alloy.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effects of Thiocyanate on Anodic Dissolution of Iron, Chromium, Nickel and Type 304 Stainless Steel: I. Electrochemical Measurements and Surface Morphology

Recently published work investigated themechanism of the catalytic effect of thiocyanate on the active dissolution of ferritic stainless steel (Type 430 stainless steel). This work has been extended to Type 304 stainless steel. Potentiostatic and impedance measurements were performed on pure iron, pure chromium, pure nickel and Type 304 stainless steel in 1 M sulfate solutions at pH = 2.5 and pH= 0. As proposed for Type 430 stainless steel, the catalytic effect of thiocyanate on anodic dissolution of Type 304 stainless steel also appears to be primarily caused by the increased dissolution rate of chromium, counteracting the formation of the Cr-O-Cr passivating network at ledges. Nickel does contribute to the corrosion resistance of Type 304 stainless steel in the presence of thiocyanate, but its beneficial effect appears to be secondary to that of chromium.

36 MATERIALS SCIENCE↗

Corrosion of Steel During Long-Term Exposure to Evolving Cementitious Environments

SRS is proceeding with closure of the H-Area Tank Farm (HTF) and F-Area Tank Farm (FTF). Closure consists of removing the bulk waste, heel removal, and filling the tank with tailored grout formulations. The long-term performance of the concrete and steel materials of construction and the closure grout is an important consideration for Performance Assessment (PA) of closed tanks in FTF and HTF. Over PA timeframes of hundreds, thousands, to tens of thousands of years, the chemical and physical properties of the concrete and steel materials will slowly degrade due to environmental exposure and material aging. In the interim these materials will provide a barrier to the leaching of radionuclides into the soil. Savannah River Remediation (SRR) is updating relevant portions of these analysis inputs to support an imminent revision to the HTF PA and a future update to the FTF PA. This analysis provides an update to the previous PA inputs for steel corrosion. The Central Scenario for the PA analysis includes three postulated modeling cases: 1) Realistic Case, 2) Compliance Case, and 3) Pessimistic Case. This analysis also included a Fast Flow Path Case. This latter case considered the circumstance where the initial condition of the concrete was a completely degraded state and that grout shrinkage exposed the steel to the soil environment immediately. In effect, the steel was unprotected by the concrete and grout. The cases have various degrees of conservatism considered. Chemical, physical and tank configuration parameters were investigated to understand their effects on the predicted time to release of the contaminants. The assessment reviewed the initial tank and steel configuration, service life degradation of the steel, and potential corrosion mechanisms associated with degradation of the concrete materials.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Fatigue Performance of Advanced High-Strength Steels (AHSS) GMAW Joints

The fatigue performance of gas metal arc welding (GMAW) joints of advanced high strength steels (AHSS) are compared and analyzed. The steel studied included a number of different grades of AHSS and baseline mild steels: DP600, DP780, DP980, M130, M220, solution annealed boron steel, fully hardened boron steels, HSLA690 and DR210 (a mild steel). Fatigue testing was conducted under a number of nominal stress ranges to obtain the S/N curves of the weld joints. A two-phase analytical model is developed to predict the fatigue performance of AHSS welds. It was found that there are appreciable differences in the fatigue S/N curves among different AHSS joints made using the same welding practices, suggesting that the local microstructure in the weld toe and root region plays non-negligible role in the fatigue performance of AHSS welds. Changes in weld parameters can influence the joint characteristics which in turn influence fatigue life of the weld joints, particularly of those of higher strength AHSS. The analytical model is capable of reasonably predicting the fatigue performance of welds made with various steel grades in this study.

36 MATERIALS SCIENCE↗

Improved Processing Techniques for Inclusion-Free Steel for Bearing and Mechanical Component Applications

High hardness, high carbide powder metallurgy tools steels such as M62 enable the operation of ball bearings at extremely high load and stress levels. Operation under such conditions increases the potential for rolling contact fatigue failure attributed to ceramic particle inclusions. To address this challenge, industry has sought steel made from ever increasing levels of cleanliness but the results have been uneven owing to the random nature of the occurrence of material flaws. One common approach is to rely upon careful ingot inspections prior to bearing manufacture. By selecting the cleanest portion of an ingot, it is expected that bearings relatively free from material flaws will result. This approach is not always successful because detrimental flaws that exist deep within an ingot can pass inspection undetected potentially causing subsequent failure. Recent efforts to commercialize an intermetallic material, 60NiTi, for rolling element bearings demonstrates a pathway to produce bearing steel that is free from unwanted ceramic particle inclusions. In this paper, the process used to make bearing grade ceramic-free NiTi alloys is described and applied to steelmaking. At its core, the NiTi process differs from steel making in one key aspect. NiTi alloys are made from elementally pure starting materials that are melted, blended and processed in equipment absolutely free from exposure to oxygen and ceramics ensuring a ceramic particle-free product. In contrast, the predominant method to make bearing steel is to employ a successive series of purification steps to reduce contamination levels below required thresholds. This paper describes the processes developed and applied to high carbide tool steel, M62. The resulting material and microstructures are evaluated and compared to M62 prepared by conventional powder metallurgy techniques. It is hoped that the application of materials manufacturing techniques used for fracture sensitive ceramics and intermetallic materials like NiTi can provide a pathway to Ultra-Clean, Ceramic-Inclusion free steels for rolling element bearings and other failure critical applications.

Steel↗

Development of FeCrAl-ODS steels for ATF cladding

As an enhanced accident tolerant fuel (ATF) for LWR at severe accident condition, FeCrAl-ODS ferritic steels have been developed, and their applicability is being studied under the Japanese MEXT program. Alloying design of FeCrAl-ODS ferritic steels has been conducted, focusing on effect of mutual interaction of Cr-Al on oxidation resistance and α'-embrittlement. Effects of co-addition of Zr and excessive oxygen have also been studied to improve high-temperature strength. The ring tensile test of the manufactured claddings showed that tensile strength increases by Zr-addition and Zr-added FeCrAl-ODS steels have the highest strength among the existed steels at entire temperature range from room temperature up to 1000 Celsius degrees. Although Zr-addition sometimes leads to growth of alumina scale by rapid inward diffusion of oxygen through zirconia inside alumina, oxidation rate of Zr-added FeCrAl-ODS steels was successfully reduced to the level of Zr-free specimen by controlling oxygen content to form Y{sub 2}Zr{sub 2}O{sub 7} inside ODS steel matrix. This finding makes possible to improve not only high-temperature strength but also steam oxidation resistance in the Zr-added FeCrAl-ODS steels. (authors)

36 MATERIALS SCIENCE↗

Crickets{sup TM} and Curies: Lessons Learned from the Steel Industry - 18221

The global nuclear power industry, and to a lesser extent, the decommissioning and demolition of old nuclear weapons plants, obviously present challenges to those in the radioactive waste management field. Some if not many of these challenges have already been dealt with, and resolved, in the steel industry, including its recycling component. This paper presents proven state-of-the-art radiation detection systems used in steel and related recycling facilities, emphasizing current, reliable and flexible technologies for characterization, volume reduction, and remote handling of recyclable solid wastes contaminated and, just as important, not contaminated, with a wide range of radioactive isotopes. It will also cover features of remotely operated waste handling equipment effective in reducing or eliminating exposure of workers engaged in decontamination and demolition work on active and/or inactive nuclear installations. The industry group identified above has a long-standing policy regarding any radioactivity in potentially recyclable as well as waste materials it receives: if it is detected, it is rejected. The US Steel Manufacturers Association (SMA) put it this way in one of their Public Policy Statements: 'SMA members have not, and will not, accept scrap that is known to be radioactively contaminated' (emphasis included in the original) (1). This policy, adopted around the globe, obviously has major implications for decommissioning and demolition projects. To put it bluntly, if rad-contaminated metal, concrete, or other materials are sent to a facility for possible recycling, reuse or even disposal, they may well be rejected. If so, the materials will be returned to the generator--at the generator's cost-and a new solution will have to be found. This also results in additional costs for the generator. Facilities in the steel making and metal recycling industries have access to, and routinely count on, a wide range of proven detection technologies and techniques for monitoring incoming shipments and sorting the materials in them. The approaches range from using sensitive handheld instruments for pinpointing and isolating small devices such as isotope-containing gauges and radium dials all the way up to technologies effective for large volumes and weights of contaminated construction and demolition material. In this latter realm, the most suitable, robust, and field-proven system for decommissioning and demolition work is a radiation detection system fitted to a grappling and/or magnetic device, known as the Crickets{sup TM} technology, which automatically scans bulk material with no added effort or time in material handling operations. Highly versatile, a Crickets{sup TM} system can be put to work on any material-handling system, including grapples handling volumes ranging from 1 up to 18 cubic yards, while detecting radioactivity in real-time over a very wide dose range, from nSv to Sv levels. Other field-proven real-time measuring radiation detection devices can be fixed to conveyor belts with traverse speeds up 3 meters/second, also measuring in real time and over the same dose range, allowing both recyclable and waste materials with a pre-set level of radioactivity to be diverted off the belt. Finally, there are highly sensitive radiation portal installations for detecting radiation from materials being transported by vehicles, including those with roll-offs, dump trailers, and other containers, again in real-time and for the same dose ranges. For vehicles, the speed must be carefully controlled-the vehicles need to travel from 5 to 10 km/h through the scanning zone to ensure that maximum detection capability is maintained. When radiation detection systems at recycling and steel making facilities detect radioactive material in an incoming shipment, these facilities have a zero tolerance for accepting the cargo. Therefore, it is imperative that material from a demolition operation that is slated to be sent for recycling or other reuse be checked at the point of demolition at similar detection levels to avoid possible rejection later of a shipment because of its radioactivity. In addition to measuring overall radiation levels (for example, total gamma), when necessary, combinations of different radiation detection media can be used to detect the presence and intensities of specific isotopes such as U-235, Cs-137, Co-60, Am-241, etc., again in real-time and over a similar dose range. These detection technologies can be fixed or transportable. More important for the rad-waste management profession, this overall systems approach can be tailored and adapted during use on-site in any dismantling, demolition or remediation project, to allow materials to be thoroughly scanned before being released to the recycling stream for reuse, or to appropriate long-term storage and disposal facilities. Potentially recyclable materials with contamination such as steel beams and rebar will set off alarms at recycling facilities, resulting in unnecessary added expenses to the generator, primarily due to increased transportation costs, time delays and additional rad-waste handling and disposal charges. Additionally, there are situations where relatively lightly contaminated materials, once identified and appropriately characterized, can be reused in new construction applications, such as concrete from demolition being used in the base layer for roads or recycled steel used for repair or construction of bridges. In other cases, specific smaller volumes can be sent to specialized rad-waste disposal sites. These radiation detection systems can also be custom tailored to ensure proper handling and disposition of contaminated materials destined for reuse in specific applications where, for example, acceptable levels of radioactivity in NORM or TENORM can be reused or safely disposed of. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Characterization of TiN, TiC and Ti(C,N) in titanium-alloyed ferritic chromium steels focusing on the significance of different particle morphologies

Titanium-alloyed ferritic chromium steels are a competitive option to classical austenitic stainless steels owing to their similar corrosion resistance. The addition of titanium significantly influences their final steel cleanliness. The present contribution focuses on the detailed metallographic characterization of titanium nitrides, titanium carbides and titanium carbonitrides with regard to their size, morphology and composition. The methods used are manual and automated Scanning Electron Microscopy with Energy Dispersive X-ray Spectroscopy as well as optical microscopy. Additional thermodynamic calculations are performed to explain the precipitation procedure of the analyzed titanium nitrides. The analyses showed that homogeneous nucleation is decisive at an early process stage after the addition of titanium. Heterogeneous nucleation gets crucial with ongoing process time and essentially influences the final inclusion size of titanium nitrides. A detailed investigation of the nuclei for heterogeneous nucleation with automated Scanning Electron Microscopy proved to be difficult due to their small size. Manual Scanning Electron Microscopy and optical microscopy have to be applied. Furthermore, it was found that during solidification an additional layer around an existing titanium nitride can be formed which changes the final inclusion morphology significantly. These layers are also characterized in detail. Based on these different inclusion morphologies, in combination with thermodynamic results, tendencies regarding the formation and modification time of titanium containing inclusions in ferritic chromium steels are derived. - Graphical abstract: Display Omitted - Highlights: • The formation and modification of TiN in the steel 1.4520 was examined. • Heterogeneous nucleation essentially influences the final steel cleanliness. • In most cases heterogeneous nuclei in TiN inclusions are magnesium based. • Particle morphology provides important information on inclusion formation.

36 MATERIALS SCIENCE↗

High-Temperature Performance of Cast CF8C-Plus Austenitic Stainless Steel

Covers and casings of small to medium size gas turbines can be made from cast austenitic stainless steels, including grades such as CF8C, CF3M, or CF10M. Oak Ridge National Laboratory and Caterpillar have developed a new cast austenitic stainless steel, CF8C-Plus, which is a fully austenitic stainless steel, based on additions of Mn and N to the standard Nb-stabilized CF8C steel grade. The Mn addition improves castability, as well as increases the alloy solubility for N, and both Mn and N synergistically act to boost mechanical properties. CF8C-Plus steel has outstanding creep-resistance at 600-900 C, which compares well with Ni-based superalloys such as alloys X, 625, 617, and 230. CF8C-Plus also has very good fatigue and thermal fatigue resistance. It is used in the as-cast condition, with no additional heat-treatments. While commercial success for CF8C-Plus has been mainly for diesel exhaust components, this steel can also be considered for gas turbine and microturbine casings. The purposes of this paper are to demonstrate some of the mechanical properties, to update the long-term creep-rupture data, and to present new data on the high-temperature oxidation behavior of these materials, particularly in the presence of water vapor.

36 MATERIALS SCIENCE↗

Latest Results from DIII-D and Their Implications for Future Devices

The DIII-D Tokamak has become one of the major sources of physics and technology data for the design of future large machines such as ITER and CIT. In large part this is because of its extremely flexible design and the ability to run tests or add new diagnostic devices with a minimum of down-time and expense. Fundamental plasma physics studies are still the major focus of our experimental program, but increasingly, we are looking at new ways to answer the complex fusion technology questions emerging from the design studies for the next-generation devices. Recent results have demonstrated world record beta plasmas, long quiescent H-mode operation, partial noninductive current drive using both neutral beam and rf power injection, single- and double-null divertor operation, and divertor particle- and heat-load management. The recently installed Advanced Divertor hardware will allow critical transport experiments to be run with independent control of the density. It will also permit the concept of dc helicity injection current drive to be tested. This paper summarizes our most important recent findings and also outlines a few of the many interesting problems that are now under study to address fusion technology questions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Report on Thermal Aging Effects on Tensile Properties of Ferritic-Martensitic Steels.

This report provides an update on the evaluation of thermal-aging induced degradation of tensile properties of advanced ferritic-martensitic steels. The report is the first deliverable (level 3) in FY11 (M3A11AN04030103), under the Work Package A-11AN040301, 'Advanced Alloy Testing' performed by Argonne National Laboratory, as part of Advanced Structural Materials Program for the Advanced Reactor Concepts. This work package supports the advanced structural materials development by providing tensile data on aged alloys and a mechanistic model, validated by experiments, with a predictive capability on long-term performance. The scope of work is to evaluate the effect of thermal aging on the tensile properties of advanced alloys such as ferritic-martensitic steels, mod.9Cr-1Mo, NF616, and advanced austenitic stainless steel, HT-UPS. The aging experiments have been conducted over a temperature of 550-750°C for various time periods to simulate the microstructural changes in the alloys as a function of time at temperature. In addition, a mechanistic model based on thermodynamics and kinetics has been used to address the changes in microstructure of the alloys as a function of time and temperature, which is developed in the companion work package at ANL. The focus of this project is advanced alloy testing and understanding the effects of long-term thermal aging on the tensile properties. Advanced materials examined in this project include ferritic-martensitic steels mod.9Cr-1Mo and NF616, and austenitic steel, HT-UPS. The report summarizes the tensile testing results of thermally-aged mod.9Cr-1Mo, NF616 H1 and NF616 H2 ferritic-martensitic steels. NF616 H1 and NF616 H2 experienced different thermal-mechanical treatments before thermal aging experiments. NF616 H1 was normalized and tempered, and NF616 H2 was normalized and tempered and cold-rolled. By examining these two heats, we evaluated the effects of thermal-mechanical treatments on material microstructures and associated mechanical properties during long-term aging at elevated temperatures. Thermal aging experiments at different temperatures and periods of time have been completed: 550°C for up to 5000 h, 600°C for up to 7500 h, and 650°C for more than 10,000 h. Tensile properties were measured on thermally aged specimens and aging effect on tensile behavior was assessed. Effects of thermal aging on deformation and failure mechanisms were investigated by using in-situ straining technique with simultaneous synchrotron XRD measurements.

36 MATERIALS SCIENCE↗

Elastic Properties in Tension and Shear of High Strength Nonferrous Metals and Stainless Steel - Effect of Previous Deformation and Heat Treatment

A resume is given of an investigation of the influence of plastic deformation and of annealing temperature on the tensile and shear elastic properties of high strength nonferrous metals and stainless steels in the form of rods and tubes. The data were obtained from earlier technical reports and notes, and from unpublished work in this investigation. There are also included data obtained from published and unpublished work performed on an independent investigation. The rod materials, namely, nickel, monel, inconel, copper, 13:2 Cr-Ni steel, and 18:8 Cr-Ni steel, were tested in tension; 18:8 Cr-Ni steel tubes were tested in shear, and nickel, monel, aluminum-monel, and Inconel tubes were tested in both tension and shear. There are first described experiments on the relationship between hysteresis and creep, as obtained with repeated cyclic stressing of annealed stainless steel specimens over a constant load range. These tests, which preceded the measurements of elastic properties, assisted in devising the loading time schedule used in such measurements. From corrected stress-set curves are derived the five proof stresses used as indices of elastic or yield strength. From corrected stress-strain curves are derived the secant modulus and its variation with stress. The relationship between the forms of the stress-set and stress-strain curves and the values of the properties derived is discussed. Curves of variation of proof stress and modulus with prior extension, as obtained with single rod specimens, consist in wavelike basic curves with superposed oscillations due to differences of rest interval and extension spacing; the effects of these differences are studied. Oscillations of proof stress and modulus are generally opposite in manner. The use of a series of tubular specimens corresponding to different amounts of prior extension of cold reduction gave curves almost devoid of oscillation since the effects of variation of rest interval and extension spacing were removed. Comparison is also obtained between the variation of the several properties, as measured in tension and in shear. The rise of proof stress with extension is studied, and the work-hardening rates of the various metals evaluated. The ratio between the tensile and shear proof stresses for the various annealed and cold-worked tubular metals is likewise calculated. The influence of annealing or tempering temperature on the proof stresses and moduli for the cold-worked metals and for air-hardened 13:2 Cr-Ni steel is investigated. An improvement of elastic strength generally is obtained, without important loss of yield strength, by annealing at suitable temperature. The variation of the proof stress and modulus of elasticity with plastic deformation or annealing temperature is explained in terms of the relative dominance of three important factors: namely, (a) internal stress, (b) lattice-expansion or work-hardening, and (c) crystal reorientation. Effective values of Poisson's ratio were computed from tensile and shear moduli obtained on tubular specimens. The variation of Poisson's ratio with plastic deformation and annealing temperature is explained in terms of the degree of anisotropy produced by changes of (a) internal stress and (b) crystal orientation.

METALS - ELASTICITY↗

A Review of Medium-Mn, Low-Density Steels for Transportation Applications

Low-density steels constitute a broad and complex alloy space (Fe–Mn–Al–C) suitable for a variety of applications. In particular, there has been growing interest in duplex (ferrite + austenite) or multiphase (+ martensite, carbides) low-density steels as a lightweight, advanced high-strength steel (AHSS) for vehicle applications, spurred by extensive decarbonization efforts. Medium-Mn (med-Mn) (3 to 12 wt pct) steels with 3.5 to 10 wt pct Al additions have decreased densities, presenting an interesting opportunity for high-specific strength, intrusion-resistant, and energy-absorbing sheet components with reduced alloying contents compared to high-Mn grades like austenitic Fe–Mn–Al–C or twinning-induced plasticity steels. Compared to leaner med-Mn steels, the physical metallurgy of med-Mn, low-density steels (MMLS) is complex and distinguished by increased δ-ferrite fractions and austenite stacking fault energies, decreased martensite start temperatures, and modified phase transformation windows. Mechanical properties of MMLS are comparable to 3rd generation AHSS, attributable to the unique, multiphase microstructures, and the array of strengthening mechanisms that can be accessed. Despite this, challenges and unknowns remain with respect to their industrial implementation, and new processing routes may need to be developed. Here, this review aims to highlight the composition effects, processing methods, microstructural evolution, deformation behavior, and application properties geared toward manufacturing and performance, altogether assessing the potential of MMLS for transportation applications.

36 MATERIALS SCIENCE↗

Extremely hard amorphous-crystalline hybrid steel surface produced by deformation induced cementite amorphization

Amorphous and nanograined (NG) steels are two categories of strong steels. However, over the past decade, their application has been hindered by their limited plasticity, the addition of expensive alloying elements, and processing challenges associated with producing bulk materials. Here in this work, we report that the surface of a carburized Fe-Mn-Si martensitic steel with extremely low elemental alloying additions can be economically fabricated into an amorphous-nanocrystalline hybrid structure. Atom probe tomography and nanobeam diffraction of a hard turned steel surface together with molecular dynamics (MD) simulations reveal that the original cementite surface structure experiences a size-dependent amorphization and phase transformation during heavy plastic deformation. MD simulations further show that the martensite-cementite interface serves as a nucleation site for cementite amorphization, and that cementite can become disordered if further strained when the cementite particles are relatively small. These graded structures exhibit a surface hardness of ~16.2 GPa, which exceeds the value of ~8.8 GPa for the original nanocrystalline martensitic steel and most nanocrystalline steels reported before. Finally, this practical and cost-efficient approach for producing a hard surface with retained bulk ductility and toughness can provide expanded opportunities for producing an amorphous-crystalline hybrid structure in steels and other alloy systems.

36 MATERIALS SCIENCE↗

Removable coatings: Thermal stability and decontamination of steel surfaces from 241 Am

This study presents a comparative analysis of several strippable materials for decontamination of steel surfaces from 241 Am. The strippable coatings were chosen to have a history of application, to be commercially available, easily handled and have different composition and formulation. Carbon steel and stainless steel surfaces (coupons) were utilized as the most representative industrial materials, and the experimental series were expanded to include the rusting treatment of these surfaces as it is common for decommissioned old nuclear facilities. The experiments followed the path of pre-screening of the strippable materials (easiness of application, peeling etc.), their characterization with Fourier-transform infrared (FTIR) spectroscopy and thermogravimetric analysis (TGA), decontamination factors (DF) or removal efficiencies for different types of steel surfaces, and enhancement of the removal efficiencies of the select strippable coatings via amendment with EDTA. As a result, DF and removal efficiencies for stainless steel (both pristine and with rusting treatment) are higher than for pristine carbon steel, and decontamination factors and removal efficiencies are higher for pristine than for rusted carbon steel across all the coatings. It is also shown that EDTA amendment can improve DF and removal efficiency for a strippable coating (i.e., CC Strip), however other factors should also be considered. Thus, the coating CC Strip exhibited easiness in handling and high DF (up to 97% when EDTA-amended), but its drying period was the longest among the rest of the materials and its thermal decomposition indicates on a risk of intense release of heat in case of a fire event.

36 MATERIALS SCIENCE↗