Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHROUDS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Internal performance of a wedge nozzle for a supersonic cruise aircraft with a multispoke primary for noise suppression

Nozzle performance was obtained with cold primary and secondary flows over a range of nozzle pressure ratio from 2 to 31 and corrected secondary-to primary-flow ratio from 0 to 11 percent. Several fixed shroud positions were tested to simulate a translating outer cylindrical shroud to provide data for both supersonic cruise and takeoff configurations. The addition of 14 spokes in the primary nozzle for noise suppression reduced the thrust efficiency 3 percent at supersonic cruise and 4.5 percent at takeoff.

Johns, A. L.↗

Small, high-pressure ratio compressor mechanical acceptance test, volume 2

The fabrication and mechanical testing of the high-pressure-ratio compressor are reported. Mechanical testing was performed to demonstrate overspeed capability, adequate rotor dynamics, electrical isolation of the gas bearing trunnion mounted diffuser and shroud and the effect of operating parameters (speed and pressure ratio) on clearance of the compressor test rig. The speed range covered was 20 to 120 percent of rated speed (80,000 rpm). Following these tests an acceptance test which consisted of a 5 hour run at 80,000 rpm was made with approximately design impeller to shroud clearances. For Vol. 1, see N73-26483.

Metty, G. R.↗

Holographic studies of shock waves within transonic fan rotors

Pulsed laser holographic interferometry has been applied to the detection of shock patterns in the outer span regions of high tip speed transonic rotors. The first holographic approach used ruby laser light reflected from a portion of the centerbody just ahead of the rotor. These holograms showed the bow wave patterns upstream of the rotor and the shock patterns just inside the blade row near the tip. Much of the region of interest was in the shadow of the blade leading edge and could not be visualized. The second holographic approach, on a different rotor, used light transmitted diagonally across the inlet annulus past the centerbody. This approach gave a more extensive view of the region bounded by the blade leading and trailing edges, by the part span shroud and by the blade tip. These holograms showed the passage shock emanating from the blade leading edge and a moderately strong conical shock originating at the intersection of the part span shroud leading edge and the blade suction surface. Reasonable details of the shock patterns were obtained from holograms which were made without extensive rig modifications.

Benser, W. A.↗

Annular truncated plug nozzle flowfield and base pressure characteristics.

The flowfield and base pressure characteristics of an internal-external expansion, truncated plug nozzle are described over the pressure ratio range from 'open' wake to 'closed' wake conditions. The effect of plug length on these characteristics, including the process of wake 'closure' is also presented. An existing method for calculating the flowfield and base pressure, for 'closed' wake operation, is modified to include the internal shock wave generated near the shroud exit. The supersonic portion of the flow is calculated using rotational axisymmetric method of characteristics. The technique of Hartree is employed so that the downstream characteristic point locations can be chosen to fit the developing flowfield. An overexpansion technique is used to detect the internal shock wave in the vicinity of the shroud exit so that its effect on the plug base pressure could be determined. Good agreement between the analytical results and experimental data is obtained for 'closed' wake operations.

Sule, W. P.↗

Vacuum system for an infrared calibration facility.

Calibration facilities for large aperture (up to 56 cm diam) infrared radiometers require commeasurable size vacuum chambers with full thermal shrouding and ultraclean pumping systems. Such a facility has been fabricated and is described in detail. The chamber is 106 cm in diameter and 4.87 m long. It utilizes integral ion pumping for operation in the 1 microtorr region. Economic considerations and time constraints of the total system program required local fabrication and, therefore, nonproprietary-type flange sealing.The sealing mechanism used was the flat flange with aluminum wire effecting the seal. Included in the discussion is the description of the cryogen distribution system which allows complete constant temperature control of the several shroud structures.

Uhlin, J.↗

Subsonic and supersonic jets and supersonic suppressor characteristics.

The flow and acoustic characteristics over a Mach number range of 0.6 to 1.5 were determined for convergent and parallel flow nozzles with room temperature air. Mean velocity and fluctuating impact and static pressure distributions were investigated. Near- and far-field acoustic measurements were obtained, and overall sound power levels were compared with subsonic theory of Lighthill and supersonic theory of Nagamatsu and Horvay. Flow and acoustic characteristics of single and multiple shroud supersonic suppressors were studied. With 191 tubes and shrouds the overall sound power level for a Mach 1.4 jet was reduced 15.3 and 20.5 db respectively.

Nagamatsu, H. T.↗

Advantages of the diffuser-augmented wind turbine

Performance optimization for a wind turbine is realized by using a shrouded diffuser to produce up to twice the power of unshrouded turbines of the same diameter. The diffuser converts the kinetic energy of the flow downstream of the rotor into a pressure rise and thus makes it possible for the rotor to capture airflow from a free stream tube area that is greater than that from the rotor itself. The flow velocity through the shrouded rotor is 20 to 60 percent greater than the free wind velocity as opposed to 67 percent less for the unshrouded case. The diffuser also makes it possible to accommodate very high wind speeds without the need of variable pitch in the rotor blades.

Oman, R. A.↗

Thrust-isolating mounting

A supporting frame for a load, such as one or more telescopes, is isolated from all multi-gravitational forces, which will be developed within that load as that load is propelled into space, by using a shroud to fully and solidly hold that load until that load has been propelled into space. Thereafter, that shroud will be jettisoned; and then supports which are on, and which are movable with, that load will have surfaces thereon moved into supporting engagement with complementary surfaces on that supporting frame to enable that supporting frame and those supports to fully and solidly hold that load.

Wetzler, D. G.↗

Holographic studies of shock waves within transonic fan rotors

NASA has funded two separate contracts to apply pulsed laser holographic interferometry to the detection of shock patterns in the outer span regions of high tip speed transonic rotors. The first holographic approach used ruby laser light reflected from a portion of the centerbody just ahead of the rotor. These holograms showed the bow wave patterns upstream of the rotor and the shock patterns just inside the blade row near the tip. The second holographic approach, on a different rotor, used light transmitted diagonally across the inlet annulus past the centerbody. This approach gave a more extensive view of the region bounded by the blade leading and trailing edges, by the part span shroud and by the blade tip. These holograms showed the passage shock emanating from the blade leading edge and a moderately strong conical shock originating at the intersection of the part span shroud leading edge and the blade suction surface.

Benser, W. A.↗

MSFC's utilization of existing design technology in the Skylab program

In the design of Skylab use was made in a number of cases of technological experience obtained in connection with earlier phases of the space program. In the development of the payload shroud use was made of Saturn V flight data. The shroud thrusting joint system was an adaptation of a system flown on the Titan IIIC. Scientific airlock hardware for Skylab was available from the Apollo Program. The design of the Orbital Workshop was based on the technology base provided by Saturn programs. Details regarding the repair tools used for correcting orbital workshop meteoroid shield/solar array anomalies which occurred during the ascent are discussed along with a commercial concept for coolant resupply, giving attention to aid provided by already existing technological developments.

Eudy, R. G.↗

Holographic flow visualization within a rotating compressor blade row

Rapid double-pulsed holographic techniques were used to visualize the shock configurations in the tip region of a lightly loaded, high tip speed fan stage. The holograms showed the passage shock emanating from the blade leading edge, a moderately strong conical shock originating at the intersection of the part span shroud leading edge and the blade suction surface, and a second conical shock originating at the intersection of the part span shroud and the blade pressure surface. Due to a limited viewing angle, the bow waves upstream of the rotor could not be observed, and only limited details of the trailing edge shocks were obtained. Reasonable details of the shock patterns were obtained from holograms which were made without extensive rig modifications. Results indicate that larger viewing windows and and holographic plates would permit a wider viewing angle and give much more coverage of the regions of interest. Also, shorter time delay for double-pulsed holograms is also desirable, and would minimize blade movement and give clearer holograms.

Benser, W. A.↗

Investigation of Ejection Releases of an MB-1 Rocket from a 0.04956-Scaled Model of the Convair F-106A Airplane at Several Mach Numbers and Simulated Altitudes

As a continuation of an investigation of the ejection release characteristics of an internally carried MB-1 rocket in the Convair F-106A airplane, fin modifications at additional Mach numbers and simulated altitudes have been studied in the 27- by 27-inch preflight jet of the Langley Pilotless Aircraft Research Station at Wallops Island, Va. The MB-1 rocket was ejected with fins open, fins closed, fins closed with a shroud around the fins, and fins folded with a "boattail" placed in between the fins. Dynamically scaled models (0.0^956 scale) were tested at simulated altitudes of 12,000, 18,850, and 27,500 feet at subsonic Mach numbers and at 18,850, 27,500, and 40,000 feet for Mach numbers of 1-39, 1-59, and 1.98. Successful ejections can be obtained for over 10 store diameters from release point by the use of a shroud around the folded fins with the proper ejection velocity and nose-down pitching moment at release. In one case investigated it was found desirable to close off the front one-third of the bomb bay. It appeared that the fins should be opened after release and within 5 "to 6 rocket diameters if no modifications are made on the rocket. An increase in fuselage angle of attack caused higher nose-up pitch rates after release.

Lee, J. B.↗

Static and wind tunnel near-field/far field jet noise measurements from model scale single-flow baseline and suppressor nozzles. Volume 2: Forward speed effects

A model scale flight effects test was conducted in the 40 by 80 foot wind tunnel to investigate the effect of aircraft forward speed on single flow jet noise characteristics. The models tested included a 15.24 cm baseline round convergent nozzle, a 20-lobe and annular nozzle with and without lined ejector shroud, and a 57-tube nozzle with a lined ejector shroud. Nozzle operating conditions covered jet velocities from 412 to 640 m/s at a total temperature of 844 K. Wind tunnel speeds were varied from near zero to 91.5 m/s. Measurements were analyzed to (1) determine apparent jet noise source location including effects of ambient velocity; (2) verify a technique for extrapolating near field jet noise measurements into the far field; (3) determine flight effects in the near and far field for baseline and suppressor nozzles; and (4) establish the wind tunnel as a means of accurately defining flight effects for model nozzles and full scale engines.

Jaeck, C. L.↗

Composite seal for turbomachinery

A gas path seal suitable for use with a turbine engine or compressor is provided. A shroud wearable or abradable by the abrasion of the rotor blades of the turbine or compressor protects the rotor blades. A compliant backing surrounds the shroud. The backing may be made of corrugated sheets or the like with adjacent layers having off-set corrugations, with axes of the folds parallel to the rotor axis. The sheets may be bonded together at points of contact by brazing, welding or the like. In another embodiment a compliant material is covered with a thin ductile layer. A mounting fixture surrounds the backing.

Bill, R. C.↗

An experimental evaluation of the performance deficit of an aircraft engine starter turbine

An experimental investigation was made to determine the reasons for the low aerodynamic performance of a 13.5 centimeter tip diameter aircraft engine starter turbine. The investigation consisted of an evaluation of both the stator and the stage. An approximate ten percent improvement in turbine efficiency was obtained when the honeycomb shroud over the rotor blade tips was filled to obtain a solid shroud surface.

Hass, J. E.↗

Advanced turbine blade tip seal system

An advanced blade/shroud system designed to maintain close clearance between blade tips and turbine shrouds and at the same time, be resistant to environmental effects including high temperature oxidation, hot corrosion, and thermal cycling is described. Increased efficiency and increased blade life are attained by using the advanced blade tip seal system. Features of the system include improved clearance control when blade tips preferentially wear the shrouds and a superior single crystal superalloy tip. The tip design, joint location, characterization of the single crystal tip alloy, the abrasive tip treatment, and the component and engine test are among the factors addressed. Results of wear testing, quality control plans, and the total manufacturing cycle required to fully process the blades are also discussed.

Zelahy, J. W.↗

Development of a locally mass flux conservative computer code for calculating 3-D viscous flow in turbomachines

The VANS successive approximation numerical method was extended to the computation of three dimensional, viscous, transonic flows in turbomachines. A cross-sectional computer code, which conserves mass flux at each point of the cross-sectional surface of computation was developed. In the VANS numerical method, the cross-sectional computation follows a blade-to-blade calculation. Numerical calculations were made for an axial annular turbine cascade and a transonic, centrifugal impeller with splitter vanes. The subsonic turbine cascade computation was generated in blade-to-blade surface to evaluate the accuracy of the blade-to-blade mode of marching. Calculated blade pressures at the hub, mid, and tip radii of the cascade agreed with corresponding measurements. The transonic impeller computation was conducted to test the newly developed locally mass flux conservative cross-sectional computer code. Both blade-to-blade and cross sectional modes of calculation were implemented for this problem. A triplet point shock structure was computed in the inducer region of the impeller. In addition, time-averaged shroud static pressures generally agreed with measured shroud pressures. It is concluded that the blade-to-blade computation produces a useful engineering flow field in regions of subsonic relative flow; and cross-sectional computation, with a locally mass flux conservative continuity equation, is required to compute the shock waves in regions of supersonic relative flow.

Walitt, L.↗

A preliminary assessment of the self-induced environment and contamination of the Space Telescope

Preliminary estimates for the internal pressures and surface contamination of the Space Telescope were made. The calculations for the transient pressures in the aft-shroud and telescope compartments considered two large communicating volumes that contain gaseous sources and sinks. The outgassing sources in the aft shroud consist of several scientific instruments, paints, insulations, and graphite-epoxy structures. With the exception of the instruments, these sources also exist in the telescope compartment. the outgassing functions were generated from ample test results at various temperatures and from internal pressure measurements in a vacuum test of one of the instruments. The venting occurs through combinations of series and parallel passages in both compartments. The calculated time constant of the two volumes and their respective passages, with the telescope protective door closed, is a few seconds, which is slightly less than that of the shuttle bay volume with the bay doors closed. With the telescope door closed, the pressures in the two compartments should decay to about 1OE-5 torr in about 200 hours. The contaminant deposits were assessed on the basis of expected partial pressures of the contaminant fraction of the outgassing. These pressures and the activation energies of the source materials were used to calculate the adsorbed and condensed deposits on the surfaces as a function of time.

Scialdone, J. J.↗