Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Relative accuracy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Calibration and Characterization of the NASA EOS Terra and Aqua MODIS Instruments

The Moderate Resolution Imaging Spectroradiometer (MODIS) instrument is operating on both of the Terra and Aqua missions within the NASA Earth Observing System (EOS). The Terra MODIS instrument began taking observations in February 2000 and the Aqua MODIS instrument began taking observations in June of 2002 and both continue to operate successfully up to the present time. The MODIS instrument scans the entire Earth every 24 hours at nominal spatial resolutions between 250 and 1000 meters. It has 36 spectral bands spanning the electromagnetic spectrum from the visible wavelengths mar 400 micrometers to the emissive thermal infrared wavelengths at 15 micrometers. The MODIS instruments produce approximately 40 geophysical products devoted to observing land, ocean, and atmospheric processes and trends. To meet the scientific objectives associated with the NASA Earth sciences efforts the MODIS instruments must be and have been carefully calibrated and the performance characterized to meet specifications and goals such as five percent radiance and two percent relative to the sun accuracy in the twenty bands providing reflected solar radiation observations and one percent radiance accuracy in the sixteen bands observing in the thermal infrared. Over the time spanning instrument development and the pre-launch calibration and characterization of the instrument through the years of operation in space, the performance of the MODIS instruments have changed in multiple ways and appropriate adjustments made in relevant algorithms and look-up tables necessary to produce observations that meet the scientific objectives and requirements. The changes have been quantified and accounted for through careful use of on-board calibration devices such as the Spectro-Radiometric Calibration Assembly (SRCA), the Solar Diffuser (SD) and its companion Solar Diffuser Stability Monitor (SDSM), deep-space and lunar observations, and calibration targets on the Earth's surface. The strictest and most difficult challenges have come in trying to meet the requirements for observing Ocean color and related ocean biology processes over time and space. Overall the MODIS observations have been very successful in providing valuable scientific and applications results. The essential capabilities of MODIS are to be provided in the future by the Visible and Infrared Imaging Radiometer Suite (VIIRS) on the National Polar Orbiting Environmental Satellite Series (NPOESS).

Salomonson, Vincent V.↗
NASA NTRS1996

Computational Analysis of Static and Dynamic Behaviour of Magnetic Suspensions and Magnetic Bearings

Static modelling of magnetic bearings is often carried out using magnetic circuit theory. This theory cannot easily include nonlinear effects such as magnetic saturation or the fringing of flux in air-gaps. Modern computational tools are able to accurately model complex magnetic bearing geometries, provided some care is exercised. In magnetic suspension applications, the magnetic fields are highly three-dimensional and require computational tools for the solution of most problems of interest. The dynamics of a magnetic bearing or magnetic suspension system can be strongly affected by eddy currents. Eddy currents are present whenever a time-varying magnetic flux penetrates a conducting medium. The direction of flow of the eddy current is such as to reduce the rate-of-change of flux. Analytic solutions for eddy currents are available for some simplified geometries, but complex geometries must be solved by computation. It is only in recent years that such computations have been considered truly practical. At NASA Langley Research Center, state-of-the-art finite-element computer codes, 'OPERA', 'TOSCA' and 'ELEKTRA' have recently been installed and applied to the magnetostatic and eddy current problems. This paper reviews results of theoretical analyses which suggest general forms of mathematical models for eddy currents, together with computational results. A simplified circuit-based eddy current model proposed appears to predict the observed trends in the case of large eddy current circuits in conducting non-magnetic material. A much more difficult case is seen to be that of eddy currents in magnetic material, or in non-magnetic material at higher frequencies, due to the lower skin depths. Even here, the dissipative behavior has been shown to yield at least somewhat to linear modelling. Magnetostatic and eddy current computations have been carried out relating to the Annular Suspension and Pointing System, a prototype for a space payload pointing and vibration isolation system, where the magnetic actuator geometry resembles a conventional magnetic bearing. Magnetostatic computations provide estimates of flux density within airgaps and the iron core material, fringing at the pole faces and the net force generated. Eddy current computations provide coil inductance, power dissipation and the phase lag in the magnetic field, all as functions of excitation frequency. Here, the dynamics of the magnetic bearings, notably the rise time of forces with changing currents, are found to be very strongly affected by eddy currents, even at quite low frequencies. Results are also compared to experimental measurements of the performance of a large-gap magnetic suspension system, the Large Angle Magnetic Suspension Test Fixture (LAMSTF). Eddy current effects are again shown to significantly affect the dynamics of the system. Some consideration is given to the ease and accuracy of computation, specifically relating to OPERA/TOSCA/ELEKTRA.

Britcher, Colin P.↗
NASA NTRS1982

Spaceborne scanner imaging system errors

The individual sensor system design elements which are the priori components in the registration and rectification process, and the potential impact of error budgets on multitemporal registration and side-lap registration are analyzed. The properties of scanner, MLA, and SAR imaging systems are reviewed. Each sensor displays internal distortion properties which to varying degrees make it difficult to generate on orthophoto projection of the data acceptable for multiple pass registration or meeting national map accuracy standards and is also affected to varying degrees by relief displacements in moderate to hilly terrain. Nonsensor related distortions, associated with the accuracy of ephemeris determination and platform stability, have a major impact on local geometric distortions. Platform stability improvements expected from the new multi mission spacecraft series and improved ephemeris and ground control point determination from the NAVSTAR/global positioning satellite systems are reviewed.

Prakash, A.↗
NASA NTRS2021

High Temperature W-band Complex Permittivity Measurements of Thermally Cycled Ceramic-Metal Composites: AlN:Mo with 0.25 vol% to 4.0 vol% Mo from 25 °C to 1000 °C in Air

An apparatus for measuring the W-band (75-110GHz) complex permittivity of dielectrics at 1000 °C was developed. This apparatus allows for measurements at approximately twice the temperature of previously published high temperature free-space measurement systems while maintaining similar precision. Challenges were addressed related to high temperature measurements, including temperature uniformity, the accuracy of temperature measurements, and preventing temperature related changes to mm-wave measurement systems. The details of complex permittivity extraction from the measured S-parameters are discussed. Sources of error related to permittivity measurement and mathematical models were identified and are discussed in detail herein. Thermally-cycled, mm-wave absorbing, aluminum nitride ceramic composites containing varying levels of molybdenum additives were measured over the range of 25-1000 °C. These measurements were compared to the same composites before thermal cycling. It was found that ceramic composites are largely stable after thermal cycling in terms of dielectric properties despite the presence of visible surface modifications.

Zane W Cohick↗
NASA NTRS1989

Support trusses for large precision segmented reflectors: Preliminary design and analysis

Precision Segmented Reflector (PSR) technology is currently being developed for a range of future applications such as the Large Deployable Reflector. The structures activities at NASA-Langley are outlined in support of the PSR program. Design concepts are explored for erectable and deployable support structures which are envisioned to be the backbone of these precision reflectors. Important functional requirements for the support trusses related to stiffness, mass, and surface accuracy are reviewed. Proposed geometries for these structures and factors motivating the erectable and deployable designs are discussed. Analytical results related to stiffness, dynamic behavior, and surface accuracy are presented and considered in light of the functional requirements. Results are included for both a 4-meter-diameter prototype support truss which is currently being designed as the Test Bed for the PSR technology development program, and for two 20-meter support structures.

Collins, Timothy J.↗
NASA NTRS1967

Relationship Between Magnitude of Applied Spin Recovery Moment and Ensuing Number of Recovery Turns

An analytical study has been made to investigate the relationship between the magnitude of the applied spin recovery moment and the ensuing number of turns made during recovery from a developed spin with a view toward determining how to interpolate or extrapolate spin recovery results with regard to determining the amount of control required for a satisfactory recovery. Five configurations were used which are considered to be representative of modern airplanes: a delta-wing fighter, a stub-wing research vehicle, a boostglide configuration, a supersonic trainer, and a sweptback-wing fighter. The results obtained indicate that there is a direct relationship between the magnitude of the applied spin recovery moments and the ensuing number of recovery turns made and that this relationship can be expressed in either simple multiplicative or exponential form. Either type of relationship was adequate for interpolating or extrapolating to predict turns required for recovery with satisfactory accuracy for configurations having relatively steady recovery motions. Any two recoveries from the same developed spin condition can be used as a basis for the predicted results provided these recoveries are obtained with the same ratio of recovery control deflections. No such predictive method can be expected to give satisfactory results for oscillatory recoveries.

SPIN DYNAMICS↗
NASA NTRS1973

Three dimensional laser Doppler velocimeter turbulence measurements in a pipe flow

The mean and turbulent u, v, and w components of a gaseous fully developed turbulent pipe flow were measured with a laser Doppler velocimeter system. Measurements of important system parameters are presented and discussed in relation to the measurement accuracy. Simultaneous comparisons of the laser Doppler and hot wire anemometer measurements in the turbulent flow provided evidence that the two systems were responding to the same flow phenomena.

Fuller, C. E., III↗
NASA NTRS1975

Application Experiences of NASTRAN Thermal Analysis in Engineering

The application of the thermal analysis phase of NASTRAN in engineering is described. Some illustrative samples are presented to demonstrate the applicability and limitation of NASTRAN thermal analysis capability. The results of the evaluation of the relative efficiency, applicability and accuracy among NASTRAN, other finite element programs, and finite difference programs are also presented.

Go, J. C. D.↗
NASA NTRS1974

Reanalysis information for eigenvalues derived from a differential equation analysis formulation

The investigation reported demonstrates that in the case considered perturbation methods can be used in a straightforward manner to obtain reanalysis information. A perturbation formula for the buckling loads of a general shell of revolution is derived. The accuracy of the obtained relations and their range of application is studied with the aid of a specific example involving a particular stiffened shell of revolution.

Thornton, W. A.↗
NASA NTRS1977

On achieving sufficient dual station range accuracy for deep space navigation at zero declination

Since the Voyager Mission will encounter Saturn at a time when the planet will be nearly in the earth's equatorial plane, earth-based orbit determination will be more difficult than usual because of the so-called zero-declination singularity associated with conventional radiometric observations. Simulation studies show that in order to meet the required delivery accuracy at Saturn, a relative range measurement between the Goldstone and Canberra Deep Space Stations must be accurate to 4.5 times the square root of two meters. Topics discussed include the nature of error sources, the methodology and technology required for calibration, the verification process concerning the nearly simultaneous range capability, a description of the ranging system, and tracking strategy.

Siegel, H. L.↗
NASA NTRS1978

Detection of horizontal crustal movements by photogrammetric methods

The photogrammetric methods can be applied only if the horizontal displacements of the ground are of the order of several centimeters, because the standard error of the points so determined cannot, at the present time, be smaller than two centimeters. The procedure to be adopted, which has already been applied with satisfactory results for the densification of geodetic nets, is the aerial analytical triangulation. The taking can be executed with wide-angle cameras (f = 15 cm), or normal-angle cameras (f = 30 cm) and format 23 x 23 cm. Since the average scale of photos must be chosen in relation with the desired accuracy and then is independent of the principal distance of the cameras, the number of photos is constant, whereas the flying height varies according to the focal length.

Solaini, L.↗
NASA NTRS1981

Comparative analysis of techniques for evaluating the effectiveness of aircraft computing systems

Performability analysis is a technique developed for evaluating the effectiveness of fault-tolerant computing systems in multiphase missions. Performability was evaluated for its accuracy, practical usefulness, and relative cost. The evaluation was performed by applying performability and the fault tree method to a set of sample problems ranging from simple to moderately complex. The problems involved as many as five outcomes, two to five mission phases, permanent faults, and some functional dependencies. Transient faults and software errors were not considered. A different analyst was responsible for each technique. Significantly more time and effort were required to learn performability analysis than the fault tree method. Performability is inherently as accurate as fault tree analysis. For the sample problems, fault trees were more practical and less time consuming to apply, while performability required less ingenuity and was more checkable. Performability offers some advantages for evaluating very complex problems.

Hitt, E. F.↗
NASA NTRS1980

Evaluation of several schemes for classification of remotely sensed data

Various numerical analysis schemes for the classification of remotely sensed data are evaluated with respect to their capabilities for crop identification. A per point Gaussian maximum likelihood classifier, per point sum-of-normal-densities classifier, per point linear classifier, per point Gaussian maximum likelihood decision tree classifier and a texture-sensitive per field Gaussian maximum likelihood classifier were applied to seven sets of Landsat MSS data on several crop types and regions. The results of the implementation of the classifiers indicate that, given a representative set of training statistics, the choice of classification algorithm of the differentiation of corn and soybeans from one another and from other crop types made relatively little difference in accuracy, whereas the use of a different training method affected the accuracy significantly. In addition, the linear classifier is found to be the easiest for the analyst to use and to cost least in computer time per classification.

Hixson, M.↗
NASA NTRS1981

Transonic airfoil calculations using solution-adaptive grids

A new algorithm for generating solution-adaptive grids (SAG) about airfoil configurations embedded in transonic flow is presented. The present SAG approach uses only the airfoil surface solution to recluster grid points on the airfoil surface, i.e., the reclustering problem is one dimension smaller than the flow-field calculation problem. Special controls automatically built into the elliptic grid generation procedure are then used to obtain grids with suitable interior behavior. This concept of redistributing grid points greatly simplifies the idea of solution-adaptive grids. Numerical results indicate significant improvements in accuracy for SAG grids relative to standard grids using the same number of points.

Holst, T. L.↗
NASA NTRS1982

Autonomous antenna tracking system for mobile symphonie ground stations

The implementation of a satellite tracking and antenna control system is described. Due to the loss of inclination control for the symphonie satellites, it became necessary to equip the parabolic antennas of the mobile Symphonie ground station with tracking facilities. For the relatively low required tracking accuracy of 0.5 dB, a low cost, step track system was selected. The step track system developed for this purpose and tested over a long period of time in 7 ground stations is based on a search step method with subsequent parabola interpolation. As compared with the real search step method, the system has the advantage of a higher pointing angle resolution, and thus a higher tracking accuracy. When the pilot signal has been switched off for a long period of time, as for instance after the eclipse, the antenna is repointed towards the satellite by an automatically initiated spiral search scan. The function and design of the tracking system are detailed, while easy handling and tracking results.

Ernsberger, K.↗
NASA NTRS1982

Applicaton of radiative transfer theory to microwave transmission medium calibrations

Precise determinations of the transmission medium loss and noise temperature contribution which are important to the performance characterization of low noise microwave receiving systems and thermal noise standards are discussed. Tropospheric loss is frequently inferred from microwave radiometer noise temperature measurements. Interpretation of these measurements requires an inversion of the radiative transfer integral equation. This is inconvenient even with computer techniques. Solutions of a rapidly convergent power series of the radiative transfer equations are presented. This solution is applicable to a low loss medium with either uniform or nonuniform loss distributions. A four layer atmosphere model is investigated to demonstrate the accuracy of the solution relative to the model. Applications include thermal noise standards and single- and dual-frequency water radiometers.

Stelzried, C. T.↗
NASA NTRS1984

Sampling system for wheat (Triticum aestivum L) area estimation using digital LANDSAT MSS data and aerial photographs

A procedure to estimate wheat (Triticum aestivum L) area using sampling technique based on aerial photographs and digital LANDSAT MSS data is developed. Aerial photographs covering 720 square km are visually analyzed. To estimate wheat area, a regression approach is applied using different sample sizes and various sampling units. As the size of sampling unit decreased, the percentage of sampled area required to obtain similar estimation performance also decreased. The lowest percentage of the area sampled for wheat estimation with relatively high precision and accuracy through regression estimation is 13.90% using 10 square km as the sampling unit. Wheat area estimation using only aerial photographs is less precise and accurate than those obtained by regression estimation.

Parada, N. D. J.↗