Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Radiation effects on electronics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

A New Plasma Radar Concept for Simultaneous Magnetic and Density Measurements

An innovative, compact 288GHz interferometer has been fabricated, tested, installed and successfully demonstrated on the LAPD-U magnetized plasma at UCLA. The system takes advantage of frequency modulated (FM) radar techniques to deliver a compact heterodyne system. In addition, the reflected power from the source is taken advantage of to eliminate the need for additional quasi-optical components. Electron density in LAPD-U plasma has recently been increased substantially thereby requiring a higher frequency/shorter wavelength interferometer to avoid deleterious refractive effects. This system satisfies those needs. The system uses a 96GHz varactor tuned Gunn oscillator which passes to a passive tripler. This tripler has ~3% conversion efficiency. The 288GHz radiation is then coupled to free space using a so-called dual-mode or Pickett horn. The output 288GHz beam is then coupled to an aspheric lens manufactured from low-loss, high-density polyethylene. This lens is employed to collimate the emerging beam. Small axial adjustment of the lens position can also be used to create a slowly focusing beam so as to optimize the measured signal. In addition, up-down or side-to-side adjustment of the lens can be utilized to steer the beam vertically or horizontally – again to optimize alignment. The propagating beam passes through a beam splitter and then through a water-free, bubble-free fused quartz window into the LAPD-U vacuum vessel. The beam-splitter is a thin sheet of G10 which reflects a small fraction of the incident power (~5 %) towards a zero-bias detector optimized for the frequency range from 220 to 300GHz. Note that waveguides at this frequency have dimensions of ~0.9mm x 0.45mm and so have very large conductive losses. This drives the use of quasi-optical propagation. The detector requires no DC bias and is very responsive (> 1V/mW into 1MΩ). Radiation is coupled to the detector via a similar lens-horn arrangement used for the launch. This reflected beam acts as the local oscillator or reference millimeter-wave beam for the detector. The remainder of the launched source beam then enters the LAPD-U vacuum vessel and passes through the plasma at the mid-plane until reaching the opposing port which is closed off with an aluminum flange. This flange is used as a mirror to retroreflect the incident 288GHz beam back along its path. The retroreflected beam exits the input port but does NOT couple directly into the zero-bias detector. Instead, the majority of the return power continues towards the 288GHz source. As mentioned above the transmitted beam enters the source a second time. This would appear undesirable. However, at these frequencies multipliers are highly non-linear elements which results in a significant portion of the return beam (~20%) re-emerging from the multiplier and horn and then coupling via the G10 beam-splitter to the zero-bias detector. This approach eliminated the need for a second quasi-optical beam-splitter. The system is extremely compact measuring approximately 28 inches x 20 inches. The above did not explain how heterodyne operation was achieved. As mentioned above the Gunn oscillator is able to be varactor tuned. This allows a low voltage to be applied to control the operating frequency of the Gunn oscillator. During heterodyne operation a sawtooth shaped voltage is applied to the varactor at 750kHz using an 80MHz Arbitrary Waveform Generator (AWG). This voltage changes the Gunn frequency linearly during the up-sweep which is then reset abruptly at the sawtooth crash to be immediately followed by another linear sweep. Passage through the 288GHz multiplier triples the frequency change experienced by the electromagnetic wave. These frequency changes are small – tens of megahertz. This FM radar approach results in the launched electromagnetic wave frequencies at the detector for the reference and plasma wave to be different. The approximately 10 ns delay propagation delay for the plasma beam results in the local oscillator and plasma beams NOT having an identical frequency – there is in fact a fixed difference frequency. The frequency tuning level of the Gunn oscillator is then adjusted so that there is ONE cycle of this difference frequency during each linear ramp. During the sawtooth crash or downward re-sweep this one cycle replays in reverse but on a very fast timescale. The process then repeats. Low-pass filtering eliminates the fast re-sweep to leave a pure sine wave heterodyne signal. When the plasma is present it introduces a phase delay in the sine wave (caused by the extremely small Doppler shift resulting from the optical path length change). Of course, to measure this phase change we need a reference. This is simply obtained from an arbitrary waveform generator which provides a synchronized output pulse train which again is low pass filtered to obtain a 750kHz sinusoidal voltage reference for the interferometer. The interferometer was installed on LAPD-U where it has worked reliably and has established that electron densities exceeding 1x10 13 cm -3 are routinely achieved. In addition, the system sensitivity was able to easily observe density fluctuation at frequencies up to 50kHz. FM Radar techniques have enabled a full demonstration of a compact, sensitive, high frequency (288GHz/1mm) heterodyne interferometer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

The impact of non-local parallel electron transport on plasma-impurity reaction rates in tokamak scrape-off layer plasmas

Abstract Plasma-impurity reaction rates are a crucial part of modelling tokamak scrape-off layer (SOL) plasmas. To avoid calculating the full set of rates for the large number of important processes involved, a set of effective rates are typically derived which assume Maxwellian electrons. However, non-local parallel electron transport may result in non-Maxwellian electrons, particularly close to divertor targets. Here, the validity of using Maxwellian-averaged rates in this context is investigated by computing the full set of rate equations for a fixed plasma background from kinetic and fluid SOL simulations. We consider the effect of the electron distribution as well as the impact of the electron transport model on plasma profiles. Results are presented for lithium, beryllium, carbon, nitrogen, neon and argon. It is found that electron distributions with enhanced high-energy tails can result in significant modifications to the ionisation balance and radiative power loss rates from excitation, on the order of 50%–75% for the latter. Fluid electron models with Spitzer-Härm or flux-limited Spitzer-Härm thermal conductivity, combined with Maxwellian electrons for rate calculations, can increase or decrease this error, depending on the impurity species and plasma conditions. Based on these results, we also discuss some approaches to experimentally observing non-local electron transport in SOL plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

The proton charge radius extracted from the initial-state radiation experiment at MAMI

Abstract We report on a comprehensive reinterpretation of the existing cross-section data for elastic electron-proton scattering obtained by the initial-state radiation technique, resulting in a significantly improved accuracy of the extracted proton charge radius. By refining the external energy corrections we have achieved an outstanding description of the radiative tail, essential for a detailed investigation of the proton finite-size effects on the measured cross sections. This development, together with a novel framework for determining the radius, based on a regression analysis of the cross sections employing a polynomial model for the form factor, led us to a new value for the charge radius, which is $$(0.878 \pm 0.011_\mathrm {stat.}\pm 0.031_\mathrm {sys.}\pm 0.002_\mathrm {mod.})\,\mathrm {fm}$$ ( 0.878 ± 0 . 011 stat . ± 0 . 031 sys . ± 0 . 002 mod . ) fm

Physics↗
DOE OSTI2024

Dynamic Scaling Analysis of Accelerated Irradiation Testing on Additive Manufacturing Materials by Positron Annihilation

The timely applications of Additive Manufacturing (AM) materials in nuclear environments require accelerated irradiation tests, mainly ion irradiation to enable rapid prototyping. Low dose ion irradiation would cause sub-nanostructure changes by generation of lattice defects, vacancies, vacancy clusters and voids and void swelling caused by cellular dislocations. Positron Annihilation Lifetime (PAL), a novel technology, sensitive towards sub-nanostructure morphology with high accuracy (about 10-7 vacancy per atom), supported by Transition Electron Microscope (TEM) would be applied to identify the type and total size of the defects. The subsequent PAL measurements and TEM surface studies would be followed by PAL analysis that includes sophisticated trapping model. The PAS results would become an input to dynamic scaling analysis (that predicts radiation effects from low dose studies for high dose effects), which incorporate mean-field theory model. The final effect is an in-depth understanding of the microstructure evolution of AM materials under ion irradiation which can be extrapolated to the studies of neutron irradiation, since ion-irradiation takes less time and do not cause the irradiation hazard. The working hypothesis is that PAL technology, that have excellent sensitivity to low-defect concentration would help to identify ion-induced material damage on the atomic and nano-scale level, which then could be extrapolated to understand the neutron damage better.

accelerated irradiation testing↗
DOE OSTI2023

Multi–length scale characterization of point defects in thermally oxidized, proton irradiated iron oxides

A key for the success of safe nuclear power generation system is to consider structural materials that are economical, meet mechanical property needs, possess good corrosion resistance, and are radiation tolerant. Nevertheless, fundamental insights that elucidate the details of radiation damage on materials corrosion performance are lacking. This includes the behavior of surface oxides which often regulate corrosion. For example, it is unclear how non-equilibrium point defects, oxide structure, mass transport in oxides, and subsequent oxidation behavior are altered by the radiation. Here, in this work, some of the effects of proton irradiation on the attributes of point defects, iron oxide microstructures, and the physical nature of the oxidation product were correlated with corrosion behavior. Iron oxides, fabricated by thermal oxidation in air at 400°C and 800°C for 1 h, were subjected to 200 keV, 0.03 dpa (displacements per atom) of proton irradiation, and subjected to corrosion reactivity assessment using AC and DC electrochemical methods. Experimental methods that target materials information at different length scales, such as positron annihilation spectroscopy (atomistic), transmission electron microscopy (mesoscopic), and electrochemical methods (macroscopic), were coupled to shed light on the impact of radiation-induced defect modifications and structural changes in oxides on corrosion reactivity which ultimately affects durability in harsh environments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structural Instability in Electrically Stressed, Oxygen Deficient BaTiO 3 Nanocrystals

The dynamics of oxygen vacancies under external stimuli dominates the performance of many solid-state devices, including capacitors, oxide memristors, anionic conductors, etc. By means of in-situ Transmission Electron Microscopy, we found in BaTiO 3 perovskite nanocrystals that formation of oxygen vacancies due to electrical stressing renders the oxide amorphizable under electron beam illumination, suggesting the presence of a threshold concentration of oxygen vacancy affecting the structural stability of BaTiO 3 crystals upon high energy radiation. In contrast to the structural change, the resistivity of the nanocrystal seems not liable to the amorphization prior to dielectric breakdown at higher voltage bias. Here, we propose that an increase in oxygen vacancy content promotes oxygen mobility in the perovskite structure allowing electron beam induced electric field to modify the local structural and composition. Our in-situ observations reveal the central role of oxygen vacancies in the structural stability of perovskites which is of paramount importance to their applications in extreme environments and suggest a potential new route to micro-processing perovskite oxides using the electron beam via oxygen vacancy management without severely compromising the electric property.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Advanced Characterization Capabilities for Nuclear Materials via Nuclear Science User Facilities (NSUF)

Advanced post-irradiation examination (PIE) techniques are required to design new or improved nuclear materials, characterize, and understand in-core behavior of fuel and materials, and support the qualification of new reactor materials. The Nuclear Science User Facilities (NSUF) is the U.S. Department of Energy Office of Nuclear Energy's only designated nuclear science user facility. NSUF provides researchers access to PIE capabilities at Idaho National Laboratory and at a diverse mix of university, national laboratory and industrial partner institutions. The PIE capabilities include novel destructive and non-destructive techniques for radiation damage characterization, such as advanced diffraction techniques (X-ray, electron, or neutron) coupled to extreme environments; in-situ observation of microstructural evolution under irradiation; in-situ irradiation to monitor corrosive attack in coolant environments; in-situ irradiation and mechanical testing; and test methods for synergistic effects of superimposed extreme environments (temperature, irradiation, stress, corrosion) on materials behaviors. This talk will provide an overview of NSUF PIE capabilities.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Impact of penetrating collisions of plasma ions on spectral line shapes

Spectral-line-broadening models have been moving towards including full Coulomb interactions between the atom and plasma, replacing the commonly used dipole approximation. The effects of the full Coulomb interaction have been thoroughly explored for plasma electrons, resulting in redshifts of spectral lines in high-energy-density plasmas. We explore the impact of a full Coulomb treatment on ion broadening. Penetrating collisions due to ions do not significantly impact the linewidths. The most significant aspect is the appearance of quasimolecular resonances in the far line wings, such as those previously observed in white-dwarf spectra. We identify several problems with the existing models. The most direct implementation causes the quasimolecular features to appear at the wrong photon energies. It is possible to include the detailed molecular structure, but this currently requires the Anderson-Talman approximation, which ignores the N-body properties of the plasma. We find that N-body effects can substantially broaden these quasimolecular features and even shift them, depending on the plasma conditions. We conclude that penetration of ions into the spatial extent of the radiator wave function does not strongly affect the usual diagnostics and may have a moderate to weak effect on opacity. Furthermore, the Rosseland mean opacity is weighted towards low-opacity regions of a spectrum, where these quasimolecular features are found.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Collaborative Research: Unravelling the Physics Associated with the Production of Extremely Dense Plasma States of Microscale (Final Report) Nanosecond-pulsed Discharges

The aim of this project is to study and establish the physical mechanisms that contribute to the formation of anomalously dense plasmas in high-pressure nanosecond-pulsed discharges. These discharges have a broad range of applications such as plasma-assisted combustion, plasma flow actuators, biomedical sterilization and exotic materials synthesis. The structure and formation of these discharges, producing high plasma densities of ~10 14 -10 15 cm -3 , are well-studied and understood. Fast-pulsed microscale high-pressure discharges can be driven to even higher densities of > 10 19 cm -3 , approaching warm dense matter conditions. The mechanisms that generate these plasmas have not been understood. Analysis of the warm dense matter state under laboratory conditions is an expensive and non-trivial endeavor. For instance, dense plasmas can be generated by electrical explosions of metal foils and wires. Plasmas generated after the explosion have a short lifetime and often present difficult conditions for diagnostics. Generation of dense plasmas was also achieved during high-voltage nanosecond pulsed discharges when the so-called explosive electron emission is obtained. Unfortunately, this process is very difficult to control for the studies of warm dense matter. In our recent study, we have shown that additional heating of plasma by lasers can further increase the density of plasma and even lead to the fully ionized state. This method, potentially, allows better control of the plasma parameters. In this work, we studied a second stage laser-heated micro-discharge using a self-consistent one-dimensional particle-in-cell Monte Carlo-collision (1D PIC-MCC) model coupled with Maxwell’s equations. We predicted the generation of a fully ionized plasma on the picosecond time scale. However, this model considered the plasma as an ideal gas despite the high pressure and the nearly fully ionized state. The ideal plasma model assumes that the dilute gas approximation is valid, where the inter-particle interactions are negligible. For charged particles this assumption holds as long as the shielded Coulomb potential assumption is valid. For very high plasma densities, this concept breaks down since the Debye sphere surrounding each charged particle no longer contains enough electrons to statistically provide the shielding of the single particle Coulomb interaction potential. At such densities, the plasma can no longer be described as ideal and non-ideal coupling effects need to be considered. In this report, we elucidate our recent work of developing a PIC-MCC model with improvements for non-ideal plasma conditions due to Coulomb coupling at high densities. In particular, we study the interaction of green light radiation and a dense microplasma, and explore the non-ideal plasma effects in this interaction. In this computational model, we implement the two most important non-ideal effects: ionization potential depression (IPD) and enhanced collision cross sections. Our primary goal is to study the physics associated with electromagnetic (EM) wave heating, also called the second-stage wave-heating, and establish the role of plasma non-ideality in this phenomenon. Our secondary goal is to improve the chemistry mechanism of the 1D PIC-MCC model by including a more detailed excited species collision treatment. At high pressures, stepwise ionization from excited species might play an important role in the ionization process. Previously, this ionization mechanism was neglected due to the excitation collision cross section of xenon being smaller than that of ionization. However, a preliminary study showed that the excited species density in the initial microplasma was an order of magnitude higher than the electron density. Therefore, my aim is to determine the significance of this additional ionization pathway to the plasma generation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Single-Particle Insights Into the Electronic Structure and Enhanced Stability of CsPbBr 3 /FAPbBr 3 Core/Crown Nanoplatelets at the Nanometer Scale

Colloidal perovskite nanoplatelets (NPLs), despite their exceptional optoelectronic properties, face significant challenges due to their intrinsic instability and trap-assisted non-radiative recombination. Although many studies employing surface engineering, such as selecting ligands or coating to passivate defects, have demonstrated improved optoelectronic properties, these enhancements are typically inferred from bulk-ensemble measurements; the effects at the single-particle level remain elusive. Here, we conduct single-particle-level studies using scanning tunneling spectroscopy (STS) on a unique core–crown system, CsPbBr 3 @FAPbBr 3 NPLs, where the lateral surfaces of the CsPbBr 3 core are coated with an FAPbBr 3 crown. Experimental density-of-states (DOS) analysis reveals a 47% reduction in deep-trap states in core-crown NPLs compared to core-only NPLs, consistent with nearly two-fold enhancements in photoluminescence quantum yields. Progressive I–V sweep measurements demonstrate superior electrical stability in core-crown NPLs, preserving band structure with minimal degradation, while core-only NPLs exhibit rapid bandgap shrinkage and trap formation. Density functional theory (DFT) calculations indicate that FA incorporation distorts Pb octahedral lattice, widening the bandgap. This study elucidates how surface engineering modulates charge localization, passivates defects, and enhances stability at the single-particle level. Moreover, by uncovering bias-induced trap states in single unpassivated NPLs, this study establishes a precise, robust approach for characterizing emerging perovskite nanocrystals.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Modeling the electron cyclotron emission radiation signature from suprathermal electrons in a tokamak

An Electron Cyclotron Emission (ECE) modeling code has been developed to model ECE radiation with an arbitrary electron momentum distribution, a small oblique angle, both ordinary (O-mode) and extraordinary polarizations (X-mode), and multiple cyclotron frequency harmonics. The emission and absorption coefficients are calculated using the Poynting theorem from the cold plasma dispersion and the electron–microwave interaction from the full anti-Hermitian tensor. The modeling shows several ECE radiation signatures that can be used to diagnose the population of suprathermal electrons in a tokamak. First, in an n = 2 X-mode (X2) optically thick plasma and oblique ECE view, the modeling shows that only suprathermal electrons, which reside in a finite region of the velocity and space domains, can effectively generate cyclotron emissions to the ECE receiver. The code also finds that the O1 mode is sensitive to suprathermal electrons of both a high v ⊥ and v || , while the X2 mode is dominantly sensitive to suprathermal electrons of a high v ⊥ . Finally, the modeling shows that an oblique ECE system with both X/O polarization and a broad frequency coverage can be used to effectively yield information of the suprathermal electron population in a tokamak.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Using convolutional neural networks to accelerate three-dimensional coherent synchrotron radiation computations

Calculating the effects of coherent synchrotron radiation (CSR) is one of the most computationally expensive tasks in accelerator physics. Here, we use convolutional neural networks (CNNs), along with a latent conditional diffusion (LCD) model, trained on physics-based simulations to speed up calculations. Specifically, we produce the 3D CSR wakefields generated by electron bunches in circular orbit in the steady-state condition. Two datasets are used for training and testing the models: wakefields generated by three-dimensional Gaussian electron distributions and wakefields from a sum of up to 25 three-dimensional Gaussian distributions. The CNNs are able to accurately produce the 3D wakefields ∼250–1000 times faster than the numerical calculations, while the LCD achieves a gain of a factor of ∼34. We also test the extrapolation and out-of-distribution generalization ability of the models. They generalize well on distributions with larger spreads than what they were trained on but struggle with smaller spreads.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Cherenkov and Transition Radiation as Low-Energy Background Sources in SuperCDMS Detectors

The Weakly Interacting Massive Particle (WIMP) has historically been a prime candidate for dark matter due to its elegant compatibility with the Minimally Supersymmetric Standard Model (MSSM). Recent dark matter experiments have ruled out much of the GeV-TeV mass range predicted by the MSSM, however, and the newest generation of direct detection experiments, such as SuperCDMS SNOLAB, have begunto explore sub-GeV dark matter. As experiments push towards lower masses, sensitivity to eV-scale electron recoil events has become increasingly important. A variety of unexplained excesses at energy deposits of 1-100 eV have been found inmany such low-mass experiments, across different detection techniques and at different excess rates. These low-energy events are not thought to be dark matter, and they must be understood and effectively removed to further improve detector energy resolution. This thesis will outline the simulation of one possible source of low-energy excess at SuperCDMS: optical photons produced from charges in uniform motion, specifically from Cherenkov radiation (CR), transition radiation (TR), and the intermediate hybrid transition-Cherenkov radiation (HR). In the latter case, the standard formulae for HR contain divergences at certain angles in transparent media, which are an artifact of their derivation and become problematic to simulate. To rsolve this, we present a novel approach to normalize the divergent HR peaks, which allows HR to transition smoothly between TR and CR in a numerical simulation. We also add TR and CR as a physics process to the SuperCDMS Monte Carlo simulation package SuperSim, based on the Geant4 simulation toolkit. To verify the physics of our addition, we show some test simulations in comparison to theoretical predictions of optical radiation intensity. We also use the simulation to make some preliminary predictions on the contribution of TR and CR to the low energy background, with the expectation that more thorough analyses will be conducted in the future.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Integrated atomic force microscopy and x-ray irradiation for in situ characterization of radiation-induced processes

Understanding radiation-induced chemical and physical transformations at material interfaces is important across diverse fields, but experimental approaches are often limited to either ex situ observations or in situ electron microscopy or synchrotron-based methods in which cases the radiation type and dose are inextricably tied to the imaging basis itself. In this work we overcome this limitation by demonstrating integration of an X-ray source with an atomic force microscope to directly monitor radiolytically-driven interfacial chemistry at the nanoscale. We illustrate the value of in situ observations by examining effects of radiolysis on material adhesion forces in aqueous solution, as well as examining the production of alkali nitrates at the interface between an alkali halide crystal surface and air. For the examined salt-air interface, direct visualization under flexible experimental conditions greatly extends prior observations by enabling the transformation process to be followed comprehensively from source-to-sink with mass balance quantitation. Overall, our novel rad-AFM opens doors into understanding the dynamics of radiolytically-driven mass transfer and surface alteration at the nanoscale in real-time.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Three-dimensional simulation of the University of Hawai‘i FEL oscillator with cavity desynchronization

In this paper, we present three-dimensional, time-dependent simulations of the University of Hawai‘i (UH) at Mānoa free-electron laser (FEL) oscillator. Using beam parameters from the UH facility, we study the pass-by-pass evolution of the radiation field, including its temporal, spectral, and transverse properties. At nominal bunch length, the radiation pulse develops temporal spiking near saturation, together with sideband formation and increased sensitivity to machine timing jitter. Our results show that modest cavity desynchronization can enhance the radiation energy by 63%. Large cavity desynchronization, on the other hand, can effectively suppress the spiking instabilities and improve robustness to timing fluctuations. Finally, we simulate a short-bunch operational mode with a bunch length comparable to the slippage length, which accelerates saturation and further amplifies the FEL power. Overall, these results provide a quantitative foundation for pulse control studies in the UH FEL oscillator and a critical benchmark for future experimental validation and machine optimization.

free-electron lasers↗
DOE OSTI2024

Transmission electron microscopy of ion irradiated ODS MA956 samples

Oxide dispersion strengthened (ODS) alloys are promising candidate materials for the next generation advanced nuclear reactors due to their superior irradiation resistance and mechanical properties. To better understand the effect of irradiation on MA956, it is essential to study higher dose (50-100 dpa) samples, so that the general trend of microstructural evolution and the resulting radiation-hardening can be deduced. Currently, ion irradiations are considered the only way to achieve doses beyond ~50 dpa in a practical time frame relevant to alloy and welding development programs. This dataset contains TEM characterization results of ODS MA956 samples that were ion irradiated under different conditions: Sample #5 (1.25 dpa at 190℃); Sample #9 (50 dpa at 190℃); Sample #15 (1.25dpa under 320℃); and Sample 17 (25 dpa at 320℃). TEM characterization focused on the irradiation induced defects (dislocation lines and loops) using the on-zone axis bright field STEM technique. These data were collected using a FEI Tecnai G2 F30 S/TEM at Microscopy and Characterization Suite (MaCS) at Center for Advanced Energy Studies (CAES), Idaho Falls, ID. This project (ion irradiation and TEM studies) was supported by the U.S. Department of Energy, Office of Nuclear Energy under DOE Idaho Operations Office Contract DE-AC07-05ID14517 as part of Nuclear Science User Facilities award #18-14784 (PI: Ramprashad Prabhakaran, PNNL).

Prabhakaran, Ramprashad↗
DOE OSTI2023

Flash electropolishing of BCC Fe and Fe-based alloys

The preparation of transmission electron microscopy (TEM) samples is a critical step in the characterization of materials, and the focused ion beam (FIB) technique is a commonly used method. However, a significant limitation of this technique is the FIB-induced damages on the foil surfaces, which can obscure the real features of interest, particularly in radiation effects studies. To overcome this limitation, this study presents a detailed description of the flash electropolishing technique, which can be used to remove the FIB damage from samples. The flash electropolishing technique has been successfully applied to a range of materials, including Fe, Fe-based model alloys, commercial Fe-Cr alloys, and advanced Fe-Cr alloys, both in their as-received and ion-irradiated states. Furthermore, the parameters used for Fe-Cr model alloys can be adjusted for commercial and advanced alloys with minimal modifications. Further, the study also examined the effects of electropolishing variables, such as perchloric acid concentration, electropolishing temperature, Cr concentration, and voltage. Qualitatively, a general trend and scoping test strategy is explored in our experiments. Overall, the flash electropolishing technique offers a promising solution to the challenges posed by FIB-induced damages in the preparation of TEM samples.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructural stability of tantalum-alloyed ferritic-martensitic steel with neutron irradiation to 7.4 dpa at ~490 °C

Specimens of a reduced-activation ferritic-martensitic steel, called CNA1, were irradiated to 7.4 displacements per atom at ~490 °C in the High Flux Isotope Reactor. Vickers hardness and tensile properties revealed consistent softening that is attributed to some recovery during irradiation, with reduced laths and dislocation density. Detailed microstructural characterization by transmission electron microscopy and energy dispersive x-ray spectroscopy showed radiation-induced dislocation loops, few cavities, and slight dissolution of M 23 C 6 and MX precipitates. Partial amorphization was only observed in M 23 C 6 precipitated in matrix. Transmutation somewhat destabilized M 23 C 6 and MX, with a stronger effect on the later one by noticeable depletion of Ta with enriched W, which is consistent with the transmutation calculations. The microstructural evolution and associated strength changes were discussed with the assistance of computational thermodynamics.

36 MATERIALS SCIENCE↗