Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RESOURCE CONSERVATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Design, Development, and Testing of a Water Vapor Exchanger for Spacecraft Life Support Systems

Thermal and environmental control systems for future exploration spacecraft must meet challenging requirements for efficient operation and conservation of resources. Maximizing the use of regenerative systems and conserving water are critical considerations. This paper describes the design, development, and testing of an innovative water vapor exchanger (WVX) that can minimize the amount of water absorbed in, and vented from, regenerative CO2 removal systems. Key design requirements for the WVX are high air flow capacity (suitable for a crew of six), very high water recovery, and very low pressure losses. We developed fabrication and assembly methods that enable high-efficiency mass transfer in a uniform and stable array of Nafion tubes. We also developed analysis and design methods to compute mass transfer and pressure losses. We built and tested subscale units sized for flow rates of 2 and 5 cu ft/min (3.4–8.5 cu m/hr). Durability testing demonstrated that a stable core geometry was sustained over many humid/dry cycles. Pressure losses were very low (less than 0.5 in. H2O (125 Pa) total) and met requirements at prototypical flow rates. We measured water recovery efficiency across a range of flow rates and humidity levels that simulate the range of possible cabin conditions. We measured water recovery efficiencies in the range of 80 to 90%, with the best efficiency at lower flow rates and higher cabin humidity levels. We compared performance of the WVX with similar units built using an unstructured Nafion tube bundle. The WVX achieves higher water recovery efficiency with nearly an order of magnitude lower pressure drop than unstructured tube bundles. These results show that the WVX provides uniform flow through flow channels for both the humid and dry streams and can meet requirements for service on future exploration spacecraft. The WVX technology will be best suited for long-duration exploration vehicles that require regenerative CO2 removal systems while needing to conserve water.

Izenson, Michael G.↗

Planning and programing in the soil conservation service

The historical base is presented for the framework plan for soil conservation. Conservation effects, resource management systems, and accomplishments, activities, and costs of the Soil Conservation Service are discussed.

Gray, R. M.↗

American Recovery and Reinvestment Act (ARRA) FEMP Technical Assistance US General Serices Administration - Project 193, John W. Bricker Federal Building, Columbus, OH

This report documents the findings from an onsite audit of the John W. Bricker Federal building located in Columbus, Ohio. The Federal landlord for this building is the General Services Administration (GSA). The focus of the audit was to identify various no-cost or low-cost energy efficiency opportunities that, once implemented, would either reduce electrical and gas consumption or increase the operational efficiency of the building. This audit also provided an opportunity to identify potential capital cost projects that should be considered in the future to acquire additional energy (electric and gas) and water savings to further increase the operational efficiency of the building.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Conservation Voltage Reduction with Distributed Energy Resource Management System, Grid-Edge, and Legacy Devices

Distribution utilities use conservation voltage reduction (CVR) to obtain energy savings and lower peak demand by reducing bus voltages. Traditionally, the CVR is accomplished by controlling the legacy assets such as load tap changers, voltage regulators, and capacitor banks. The deployment of the advanced distribution management system (ADMS) and distributed energy resource management system (DERMS) enables the integration of distributed energy resources into the distribution networks and provide the grid services including CVR. This paper studies the coordinated operation of an ADMS and a DERMS in achieving CVR and voltage regulation. A commercial ADMS uses legacy devices and Edge-of-Network Grid Optimization (ENGO) devices to obtain energy savings through CVR. A prototype DERMS dispatches the photovoltaic smart inverters based on real-time optimal power low to ensure voltage regulation across the feeder. The results show that the coordinated operation of ADMS and DERMS is effective in achieving CVR and voltage regulation. Specifically, energy savings of up to 4.7% are observed in the real utility distribution system used in this study.

advanced distribution management system↗

Conservation Voltage Reduction with Distributed Energy Resource Management System, Grid-Edge, and Legacy Devices

Distribution utilities use conservation voltage reduction (CVR) to obtain energy savings and lower peak demand by reducing bus voltages. Traditionally, the CVR is accomplished by controlling the legacy assets such as load tap changers, voltage regulators, and capacitor banks. The deployment of the advanced distribution management system (ADMS) and distributed energy resource management system (DERMS) enables the integration of distributed energy resources into the distribution networks and provide the grid services including CVR. This paper studies the coordinated operation of an ADMS and a DERMS in achieving CVR and voltage regulation. A commercial ADMS uses legacy devices and Edge-of-Network Grid Optimization (ENGO) devices to obtain energy savings through CVR. A prototype DERMS dispatches the photovoltaic smart inverters based on real-time optimal power low to ensure voltage regulation across the feeder. The results show that the coordinated operation of ADMS and DERMS is effective in achieving CVR and voltage regulation. Specifically, energy savings of up to 4.7% are observed in the real utility distribution system used in this study.

advanced distribution management system↗

Conservation Voltage Reduction with Distributed Energy Resource Management System, Grid-Edge, and Legacy Devices

Distribution utilities use conservation voltage reduction (CVR) to obtain energy savings and lower peak demand by reducing bus voltages. Traditionally, the CVR is accomplished by controlling the legacy assets such as load tap changers, voltage regulators, and capacitor banks. The deployment of the advanced distribution management system (ADMS) and distributed energy resource management system (DERMS) enables the integration of distributed energy resources into the distribution networks and provide the grid services including CVR. This paper studies the coordinated operation of an ADMS and a DERMS in achieving CVR and voltage regulation. A commercial ADMS uses legacy devices and Edge-of-Network Grid Optimization (ENGO) devices to obtain energy savings through CVR. A prototype DERMS dispatches the photovoltaic smart inverters based on real-time optimal power low to ensure voltage regulation across the feeder. The results show that the coordinated operation of ADMS and DERMS is effective in achieving CVR and voltage regulation. Specifically, energy savings of up to 4.7% are observed in the real utility distribution system used in this study.

advanced distribution management system↗

American Recovery and Reinvestment Act (ARRA) FEMP Technical Assistance U.S. General Services Administration – Project 195 John Seiberling Federal Office Building and U.S. Courthouse, Akron, Ohio

This report documents the findings from an onsite audit of the John Seiberling Federal building located in Akron, Ohio. The Federal landlord for this building is the General Services Administration (GSA). The focus of the audit was to identify various no-cost or low-cost energy efficiency opportunities that, once implemented, would reduce in either electrical and gas consumption and increase the operational efficiency of the building. This audit also provided an opportunity to identify potential capital cost projects that should be considered in the to acquire additional energy (electric and gas) and water savings to further increase the operational efficiency of the building.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Sustaining Water Resources: Environmental and Economic Impact

Water is essential to human health and economic development due to its utilization in sanitation, agriculture, and energy. Supplying water to an expanding world population requires simultaneous consideration of multiple societal sectors competing for limited resources. Water conservation, supply augmentation, distribution, and treatment of contaminants must work in concert to ensure water sustainability. Water is linked to other sectors, and the quantity and quality of water resources are changing. The efficient use of water in agriculture, the largest user of water worldwide, via drip irrigation is described as is the use of energy-intensive reverse osmosis to supplement freshwater supplies. Efforts to manage watersheds and model their responses to severe weather events are discussed along with efforts to improve the predictability of their function. The regional competition for water resources impacts both energy and water supply reliability, which requires that nations balance both for sustainable economic development. The use of water and energy in the US is described which provides a lens through which to both rethink the interrelationship of water and energy as well as evaluate technological developments. Advances in nanotechnology are highlighted as one emerging technology. Finally, these results underscore the multifaceted nature of water sustainability, its interrelationship to energy and economic development, and the need to develop, manage and regulate water systems in a concerted manner.

54 ENVIRONMENTAL SCIENCES↗

American Recovery and Reinvestment Act Federal Energy Management Program Technical Assistance Project 184 U.S. Customs and Border Protection Laboratory, Houston, Texas

This report documents the findings of an on-site energy audit of the U.S. Customs and Border Protection (CBP) Laboratory in Houston, Texas. The focus of the audit was to identify various no-cost and low-cost energy efficiency opportunities that, once implemented, would reduce electricity and gas consumption and increase the operational efficiency of the building. This audit also provided an opportunity to identify potential capital cost projects that should be considered in the future to acquire additional energy (electric and gas) and water savings to further increase the operational efficiency of the building.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

The first Earth Resources Technology Satellite (ERTS-1)

The first Earth Resources Technology Satellite (ERTS-1) makes images of the earth's surface in four portions of the electromagnetic spectrum with sufficient spatial resolution and with a minimum of geometric distortions, so that these images may be applied experimentally to the study of geophysical processes relating to earth resources, to the exploration and conservation of these resources, and to the assessments of environmental stresses. During the first six months of operation, ERTS-1 has imaged 6.5 million square kilometers of the earth's surface every day, covering most major land masses and coastal zones as well as both polar regions of this planet. These images as well as the results of their analyses are available to all people throughout the world. Scientific investigators of all countries have been invited to participate in the utilization of ERTS-1 observations. Many of them have already demonstrated the great efficiency, economy, and reliability of making earth surveys from space.

Nordberg, W.↗

Lunar subsurface architecture enhanced by artificial biosphere concepts

The integration of artificial biosphere technology with subselene architecture can create a life-enhancing, productive habitat that is safe from solar radiation and extreme temperature fluctuations while maximizing resources brought from Earth and derived from lunar regolith. In the short term, the resulting biotectural (biosphere and architectural) designs will not only make the structures more habitable, productive, and manageable, but will ultimately provide the self-sufficiency factors necessary for the mature lunar settlement. From a long-term perspective, this biotecture approach to astronautics and extraterrestrial development (1) helps reduce mass lift requirements, (2) contributes to habitat self-sufficiency, and (3) actualizes at least one philosophy of solar system exploration, which is to exploit nonterrestrial resources in an effort to conserve our natural resources on this planet.

Klassi, Jason D.↗

Conservation Voltage Reduction with Distributed Energy Resource Management System, Grid-Edge, and Legacy Devices: Preprint

Distribution utilities use conservation voltage reduction (CVR) to obtain energy savings and lower peak demand by reducing bus voltages. Traditionally, the CVR is accomplished by controlling the legacy assets such as load tap changers, voltage regulators, and capacitor banks. The deployment of the advanced distribution management system (ADMS) and distributed energy resource management system (DERMS) enables the integration of distributed energy resources into the distribution networks and provide the grid services including CVR. This paper studies the coordinated operation of an ADMS and a DERMS in achieving CVR and voltage regulation. A commercial ADMS uses legacy devices and Edge-of-Network Grid Optimization (ENGO) devices to obtain energy savings through CVR. A prototype DERMS dispatches the photovoltaic smart inverters based on real-time optimal power low to ensure voltage regulation across the feeder. The results show that the coordinated operation of ADMS and DERMS is effective in achieving CVR and voltage regulation. Specifically, energy savings of up to 4.7% are observed in the real utility distribution system used in this study.

advanced distribution management system↗

Comprehensive Lifecycle Planning and Management System For Addressing Water Issues Associated With Shale Gas Development In New York, Pennsylvania, And West Virginia

The objective of this project is to develop a modeling system to allow operators and regulators to plan all aspects of water management activities associated with shale gas development in the target project area of New York, Pennsylvania, and West Virginia (target area ), including water supply, transport, storage, use, recycling, and disposal and which can be used for planning, managing, forecasting, permit tracking, and compliance monitoring. The proposed project is a breakthrough approach to represent the entire shale gas water lifecycle in one comprehensive system with the capability to analyze impacts and options for operational efficiency and regulatory tracking and compliance, and to plan for future water use and disposition. It will address all of the major water-related issues of concern associated with shale gas development in the target area, including water withdrawal, transport, storage, use, treatment, recycling, and disposal. It will analyze the costs, water use, and wastes associated with the available options, and incorporate constraints presented by permit requirements, agreements, local and state regulations, equipment and material availability, etc. By using the system to examine the water lifecycle from withdrawals through disposal, users will be able to perform scenario analysis to answer "what if" questions for various situations. The system will include regulatory requirements of the appropriate state and regional agencies and facilitate reporting and permit applications and tracking. These features will allow operators to plan for more cost effective resource production. Regulators will be able to analyze impacts of development over an entire area. Regulators can then make informed decisions about the protections and practices that should be required as development proceeds. This modeling system will have myriad benefits for industry, government, and the public. For industry, it will allow planning all water management operations for a project or an area as one entity to optimize water use and minimize costs subject to regulatory and other constraints. It will facilitate analysis of options and tradeoffs, and will also simplify permitting and reporting to regulatory agencies. The system will help regulators study cumulative impacts of development, conserve water resources, and manage disposal options across a region. It will also allow them to track permits and monitor compliance. The public will benefit from water conservation, improved environmental performance as better system wide decisions are made, and greater supply of natural gas, with attendant lower prices, as costs are reduced and development is assisted through better planning and scheduling. Altogether, better economics and fewer barriers will facilitate recovery of the more than 300 trillion cubic feet of estimated recoverable natural gas resource in the Marcellus Shale in a manner that protects the environment.

03 NATURAL GAS↗

HarDWR - Water Management Area (WMA) Shapefiles

A dataset within the Harmonized Database of Western U.S. Water Rights (HarDWR). For a detailed description of the database, please see the meta-record v2.0. Changelog v2.0 - No changes v1.0 - Initial public release Description Borders of all Water Management Areas (WMAs) across the 11 western-most states of the coterminous United States are available filtered through a single source. The legal name for this set of boundaries varies state-by-state. The data is provided as two compressed shapefiles. One, stateWMAs, contains data for all 11 states. For 10 of those states, Arizona being the exception, the polygons represent the legal management boundaries used by those states to manage their surface and groundwater resources respectively. WMAs refer to the set of boundaries a particular state uses to manage its water resources. Each set of boundaries was collected from the states individually, and then merged into one spatial layer. The merging process included renaming some columns to enable merging with all other source layers, as well as removing columns deemed not required for followup analysis. The retained columns for each boundary are: basinNum - the state provided unique numerical ID; basinName - the state provided English name of the area, where applicable; state - the state name; and uniID - a unique identifier we created by concatenating the state name, and underscore, and the state numerical ID. Arizona is unique within this collection of states in that surface and groundwater resources are managed using two separate sets of boundaries. During our followup analysis (Grogan et al., in review) we decided to focus on one set of boundaries, those for surface water. This is due to the recommendation of our hydrologists that the surface water boundary set is a more realist representation of how water moves across the landscape, as a few of the groundwater boundaries are based on political and/or economic considerations. Therefore, the Arizona surface WMAs are included within stateWMAs. The Arizona groundwater WMAs are provided as a separate file, azGroundWMAs, as a companion to the first file for completeness and general reference. WMA spatial boundary data sources by state: Arizona: Arizona Surface Water Watersheds; Collected February, 2020; https://gisdata2016-11-18t150447874z-azwater.opendata.arcgis.com/datasets/surface-watershed/explore?location=34.158174%2C-111.970823%2C7.50 Arizona: Arizona Ground Water Basins; Collected February, 2020; https://gisdata2016-11-18t150447874z-azwater.opendata.arcgis.com/datasets/groundwater-basin-2/explore?location=34.158174%2C-111.970823%2C7.50 California: California CalWater 2.2.1; Collected February, 2020; https://www.mlml.calstate.edu/mpsl-mlml/data-center/data-entry-tools/data-tools/gis-shapefile-layers/ Colorado: Colorado Water District Boundaries; Collected February, 2020; https://www.colorado.gov/pacific/cdss/gis-data-category Idaho: Idaho Department of Water Resources (IDWR) Administrative Basins; Collected November, 2015; https://data-idwr.opendata.arcgis.com/datasets/fb0df7d688a04074bad92ca8ef74cc26_4/explore?location=45.018686%2C-113.862284%2C6.93 Montana: Collected June, 2019; Directly contacted Montana Department of Natural Resources and Conservation (DNRC) Office of Information Technology (OIT) Nevada: Nevada State Engineer Admin Basin Boundaries; Collected April, 2020 https://ndwr.maps.arcgis.com/apps/mapviewer/index.html?layers=1364d0c3a0284fa1bcd90f952b2b9f1c New Mexico: New Mexico Office of the State Engineer (OSE) Declared Groundwater Basins; Collected April, 2020 https://geospatialdata-ose.opendata.arcgis.com/datasets/ose-declared-groundwater-basins/explore?location=34.179783%2C-105.996542%2C7.51 Oregon: Oregon Water Resources Department (OWRD) Administrative Basins; Collected February, 2020; https://www.oregon.gov/OWRD/access_Data/Pages/Data.aspx Utah: Utah Adjudication Books; Collected April, 2020; https://opendata.gis.utah.gov/datasets/utahDNR::utah-adjudication-books/explore?location=39.497165%2C-111.587782%2C-1.00 Washington: Washington Water Resource Inventory Areas (WRIA); Collected June, 2017; https://ecology.wa.gov/Research-Data/Data-resources/Geographic-Information-Systems-GIS/Data Wyoming: Wyoming State Engineer's Office Board of Control Water Districts; Collected June, 2019; Directly contacted Wyoming State Engineer's Office

Economics↗

Use of Air2Air Technology to Recover Fresh-Water from the Normal Evaporative Cooling Loss at Coal-Based Thermoelectric Power Plants

This program was undertaken to build and operate the first Air2Air{trademark} Water Conservation Cooling Tower at a power plant, giving a validated basis and capability for water conservation by this method. Air2Air{trademark} water conservation technology recovers a portion of the traditional cooling tower evaporate. The Condensing Module provides an air-to-air heat exchanger above the wet fill media, extracting the heat from the hot saturated moist air leaving in the cooling tower and condensing water. The rate of evaporate water recovery is typically 10%-25% annually, depending on the cooling tower location (climate).

01 COAL, LIGNITE, AND PEAT↗

A decision support tool for e-waste recycling operations using the hen-and-chicks bio-inspired optimization metaheuristic

E-waste from end-of-life electrical and electronic devices is one of the fastest growing waste streams from households and businesses. E-waste recycling yields environmental sustainability and economic benefits. Due to continuous changes in e-waste types and compositions, recycling businesses face challenges to optimize their operational configuration to achieve better economic and environmental performance. To help e-waste recyclers mitigate this problem, we have developed a modular decision support tool called the Comprehensive Manufacturing Assessment Tool (CMAT) that can simulate both e-waste recycling operations and economics. This tool can give valuable insights regarding the profitability of the entire operation and different e-waste types. In addition, a new bio-inspired metaheuristic optimization algorithm, hen-and-chicks optimization (HACO), was developed to assign manpower to different workstations to maximize operational efficiencies. According to the results of our case study, laptops, desktops, and computer peripherals are the three electronic waste products that produce the most profit. Our examination of the sensitivity of material prices shows that the price of steel has the most significant influence on total profit, because it is the most widely used material in the majority of electronic devices. We have released the decision support tool as open-source software under a general public license. It could be customized for other recycling industries beyond e-waste to achieve business sustainability by making their operations more efficient.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Comprehensive framework for assessing and optimizing existing research networks

Conservation, monitoring, and research networks, or collections of ecological research sites unified under a common mission of data collection or a research mission, are essential infrastructure for understanding large landscapes. However, most networks developed opportunistically over decades rather than through systematic design, creating potential limitations in the ability to address conservation challenges across entire regions. We developed a framework to evaluate how well an existing research network represents the environmental conditions its members study and devised an approach to rank sites of priority for strategic expansion. Our approach measures performance through environmental representativeness, geographic coverage, and adequacy for scientific inference and thus optimizes limited monitoring resources to maximize scientific impact. We demonstrated this approach with the U.S. Department of Agriculture (USDA) Forest Service Experimental Forests and Ranges Network (EFRN), a 79‐site network across the United States that grew opportunistically over a century. At the national scale, the network effectively captured high‐biomass forests important for carbon cycle research; 82% of forest biomass was in well‐represented areas. Some areas in Texas, Florida, the Rocky Mountains, and the West Coast had no relevant EFRN sites, which limits the ability to make regional inferences. A fundamental challenge for the EFRN was that sites improving regional extent coverage sometimes provided minimal national benefits, which can create conflicts between local and global priorities. Adding the highest‐ranked candidate site provided a relevant site for 17% of currently poorly represented 1‐km pixel cells nationally, but regional and national site rankings varied considerably due to nested spatial inference. This framework provides quantitative tools for strategic infrastructure decision‐making, ensures that limited monitoring resources maximize conservation impact, and can be applied broadly to address the widespread challenge of optimizing conservation and monitoring networks worldwide.

additional site↗

Feasibility Study of Economics and Performance of Solar Photovoltaics at the Santo Domingo Pueblo in Sandoval County, New Mexico

The U.S. Environmental Protection Agency (EPA), in accordance with the RE-Powering America's Land initiative, selected the Pueblo of Santo Domingo in Sandoval County, New Mexico, for a renewable energy production feasibility study. The National Renewable Energy Laboratory (NREL) provided technical assistance for this project. The purpose of this report is to assess specific areas on the Pueblo for potential installation of photovoltaic (PV) systems and to estimate the cost, performance, and site impacts of different PV options. The report also recommends financing options that could assist in the implementation of these PV systems.

14 SOLAR ENERGY↗