Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RESIDUAL STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Residual Stresses in Thermal Barrier Coatings for a Cu-8Cr-4Nb Substrate System

Analytical calculations were conducted to determine the thermal stresses developed in a coated copper-based alloy, Cu-8%(at.%)Cr-4%Nb (designated as GRCop-84), after plasma spraying and during heat-up in a simulated rocket engine environment. Finite element analyses were conducted for two coating systems consisting of a metallic top coat, a pure copper bond coat and the GRCop-84. The through thickness temperature variations were determined as a function of coating thickness for two metallic coatings, a Ni-17%(wt%)Cr-6%Al-0.5%Y alloy and a Ni-50%(at.%)Al alloy. The residual stresses after low-pressure plasma spraying of the NiCrAlY and NiAl coatings on GRCop-84 substrate were also evaluated. These analyses took into consideration a 50.8 mm copper bond coat and the effects of an interface coating roughness. The through the thickness thermal stresses developed in coated liners were also calculated after 15 minutes of exposure in a rocket environment with and without an interfacial roughness.

Ghosn, Louis J.↗
NASA NTRS1977

Residual stresses in boron/tungsten and boron/carbon fibers

By measuring the change in fracture stress of 203 micrometer diameter fibers of boron on tungsten (B/W) as a function of fiber diameter as reduced by chemical etching, it is shown that the flaws which limit B/W fiber strength are located at the surface and in the tungsten boride core. After etching to a diameter of 188 micrometers m virtually all fiber fractures were caused by core flaws, the average strength being 4.50 GN/sq m. If both the surface and core flaws are removed, the fracture strength, limited by flaws in the boron itself, is approximately 6.89 GN/sq m. This was measured on B/W fibers which were split longitudinally and had their cores removed by chemical etching. The longitudinal residual stress distribution was determined for 102 micrometer diameter B/W and B/C fibers.

Behrendt, D. R.↗
NASA NTRS1988

Photoelastic measurements of residual stresses for NDE

Photoelastic measurements of residual strains are used extensively in the QC and inspection of transparent materials. A new method of measurements, based on Spectral Contents Analysis, is described in this paper. The method uses a personal computer for photoelastic data acquisition, eliminating personal skill and subjectivity. the new tool should make the measurements of residual strains for QC simpler and more reliable.

Redner, Alex S.↗
NASA NTRS1948

Residual Stress Analysis of Overspeeded Disk with Central Hole by X-ray Diffraction

An X-ray - diffraction analysis of residual surface stresses after plastic strain was introduced in a parallel-sided 3S-O aluminum disk with a central hole by two types of centrifugal overspeed is reported. Both tangential and radial stresses were generally tensile with large local variations near the hole where surface stresses may have been partly superficial. These stresses were both tensile and compressive dependent on the distance from the disk center when mass compression was effected near the hole.

ALUMINUM↗
NASA NTRS1977

Influence of residual stresses on the tensile strength of composite-metal sandwich laminates

The tensile strength of boron-epoxy/aluminum sandwich laminates is discussed relative to the residual thermal stresses generated by curing and bonding at elevated temperatures. It is shown that the sandwich laminates investigated exhibit three dinstinct modes of failure, depending upon the fiber orientation of the composite. Sandwich laminates with moderate to high percentage of 0-deg fibers exhibit early failures initiated by edge effect; laminates with moderate to high percentage of 90-deg fibers fail according to a first-ply failure criterion; laminates with moderate to high percentages of plus or minus 45 deg plies fail at strains equal to or greater than the failure strain of the corresponding all-composite laminate.

Herakovich, C. T.↗
DOE OSTI2016

Final Report: Characterization of Canister Mockup Weld Residual Stresses

Stress corrosion cracking (SCC) of interim storage containers has been indicated as a high priority data gap by the Department of Energy (DOE) (Hanson et al., 2012), the Electric Power Research Institute (EPRI, 2011), the Nuclear Waste Technical Review Board (NWTRB, 2010a), and the Nuclear Regulatory Commission (NRC, 2012a, 2012b). Uncertainties exist in terms of the environmental conditions that prevail on the surface of the storage containers, the stress state within the container walls associated both with weldments as well as within the base metal itself, and the electrochemical properties of the storage containers themselves. The goal of the work described in this document is to determine the stress states that exists at various locations within a typical storage canister by evaluating the properties of a full-diameter cylindrical mockup of an interim storage canister. This mockup has been produced using the same manufacturing procedures as the majority of the fielded spent nuclear fuel interim storage canisters. This document describes the design and procurement of the mockup and the characterization of the stress state associated with various portions of the container. It also describes the cutting of the mockup into sections for further analyses, and a discussion of the potential impact of the results from the stress characterization effort.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗