Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Phased”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Infrared Signatures for Phase Identification in Hafnium Oxide Thin Films

Phase identification in HfO 2 -based thin films is a prerequisite to understanding the mechanisms stabilizing the ferroelectric phase in these materials, which hold great promise in next-generation non-volatile memory and computing technology. While grazing-incidence X-ray diffraction is commonly employed for this purpose, it has difficulty unambiguously differentiating between the ferroelectric phase and other metastable phases that may exist due to similarities in the d-spacings, their low intensities, and the overlapping of reflections. Infrared signatures provide an alternative route. However, their use in phase identification remains limited because phase control has overwhelmingly been accomplished via substituents, thereby convoluting infrared signatures between the substituent and the phase changes they induce. Herein, we report the infrared optical responses of three undoped hafnium oxide films where annealing conditions have been used to create films consisting primarily of the ferroelectric polar orthorhombic Pca2 1 , antipolar orthorhombic Pbca, and monoclinic P2 1 /c phases, as was confirmed via transmission electron microscopy (TEM), UVvisible optical properties, and electrical property measurements. Vibrational signatures acquired from synchrotron nano-Fourier transform infrared spectroscopy (nano-FTIR) are shown to be capable of differentiating between the phases in a non-destructive, rapid, and nanoscale manner. The utility of nano-FTIR is illustrated for a film exhibiting an antiferroelectric polarization response. In this sample, it is proven that this behavior results from the Pbca phase rather than the often-cited tetragonal phase. Here, by demonstrating that IRspectroscopy can unambiguously distinguish phases in this material, this work establishes a tool needed to isolate the factors dictating ferroelectric phase stability in HfO 2 -based materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

High Pressure–Temperature Study of MgF 2 , CaF 2 , and BaF 2 by Raman Spectroscopy: Phase Transitions and Vibrational Properties of AF 2 Difluorides

The phase transition of AF 2 difluorides strongly depends on pressure, temperature, and cationic radius. Here, we have investigated the phase transition of three difluorides, including MgF 2 , CaF 2 , and BaF 2 , at simultaneously high pressures and temperatures using Raman spectroscopy and X-ray diffraction in externally heated diamond anvil cells up to 55 GPa at 300–700 K. Rutile-type difluoride MgF 2 with a small cationic radius undergoes a transition to the CaCl 2 -type phase at 9.9(1) GPa and 300 K, to the HP-PdF 2 -type phase at 21.0(2) GPa, and to the cotunnite-type phase at 44.2(2) GPa. The phase transition pressure to the HP-PdF 2 and cotunnite structure at 300 K for our single crystal was found to be higher than that in previous studies using polycrystalline samples. Elevating the temperature increases the transition pressure from rutile- to the CaCl 2 -type phase but has a negative influence on the transition pressure when MgF 2 transforms from the HP-PdF 2 - to cotunnite-type phase. Meanwhile, the transition pressure from the CaCl 2 - to HP-PdF 2 -type phase for MgF 2 was identified to be independent of the temperature. Raman peaks suspected to belong to the α-PbO 2 -type phase were observed at 14.6–21.0(1) GPa and 400–700 K. At 300 K, difluorides CaF 2 and BaF 2 in the fluorite structure with larger cationic radii transform to the cotunnite-type phase at 9.6(3) and 3.0(3) GPa at 300 K, respectively, and BaF 2 further undergoes a transition to the Ni 2 In-type phase at 15.5(4) GPa. For both CaF 2 and BaF 2 , elevating the temperature leads to a lower transition pressure from fluorite- to the cotunnite-type phase but has little influence on the transition to the Ni 2 In structure. Raman data provide valuable insights for mode Grüneisen parameters. We note that the mode Grüneisen parameters for both difluorides and dioxides vary linearly with the cation radius. Further calculations for the mode Grüneisen parameters at high pressures for MgF 2 , CaF 2 , and BaF 2 yield a deeper understanding of the thermodynamic properties of the difluorides.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

The pervasive impact of critical fluctuations in liquid–liquid extraction organic phases

Liquid-liquid extraction is an essential chemical separation technique where polar solutes are extracted from an aqueous phase into a nonpolar organic solvent by amphiphilic extractant molecules. A fundamental limitation to the efficiency of this important technology is third phase formation, wherein the organic phase splits upon sufficient loading of polar solutes. The nanoscale drivers of phase splitting are challenging to understand in the complex hierarchically structured organic phases. In this study, we demonstrate that the organic phase structure and phase behavior are fundamentally connected in a way than can be understood with critical phenomena theory. For a series of binary mixtures of trialkyl phosphate extractants with linear alkane diluents, we combine small angle x-ray scattering and molecular dynamics simulations to demonstrate how the organic phase mesostructure over a wide range of compositions is dominated by critical concentration fluctuations associated with the critical point of the third phase formation phase transition. These findings reconcile many longstanding inconsistencies in the literature where small angle scattering features, also consistent with such critical fluctuations, were interpreted as reverse micellar-like particles. Altogether, this study shows how the organic phase mesostructure and phase behavior are intrinsically linked, deepening our understanding of both and providing a new framework for using molecular structure and thermodynamic variables to control mesostructure and phase behavior in liquid-liquid extraction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Data-driven analysis and prediction of stable phases for high-entropy alloy design

High-entropy alloys (HEAs) represent a promising class of materials with exceptional structural and functional properties. However, their design and optimization pose challenges due to the large composition-phase space coupled with the complex and diverse nature of the phase formation dynamics. In this study, a data-driven approach that utilizes machine learning (ML) techniques to predict HEA phases and their composition-dependent phases is proposed. By employing a comprehensive dataset comprising 5692 experimental records encompassing 50 elements and 11 phase categories, we compare the performance of various ML models. Our analysis identifies the most influential features for accurate phase prediction. Furthermore, the class imbalance is addressed by employing data augmentation methods, raising the number of records to 1500 in each category, and ensuring a balanced representation of phase categories. The results show that XGBoost and Random Forest consistently outperform the other models, achieving 86% accuracy in predicting all phases. Additionally, this work provides an extensive analysis of HEA phase formers, showing the contributions of elements and features to the presence of specific phases. We also examine the impact of including different phases on ML model accuracy and feature significance. Notably, the findings underscore the need for ML model selection based on specific applications and desired predictions, as feature importance varies across models and phases. This study significantly advances the understanding of HEA phase formation, enabling targeted alloy design and fostering progress in the field of materials science.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Relativistic hybrid stars with sequential first-order phase transitions and heavy-baryon envelopes

We compute the mass, radius and tidal deformability of stars containing phase transitions from hadronic to quark phase(s). These quantities are computed for three types of hadronic envelopes: purely nuclear, hyperonic, and Δ-resonance--hyperon admixed matter. We consider either a single first-order phase transition to a quark phase with a maximally stiff equation of state (EOS) or two sequential first-order phase transitions mimicking a transition from hadronic to a quark matter phase followed by a second phase transition to another quark phase. We explore the parameter space which produces low-mass twin and triplet configurations where equal-mass stars have substantially different radii and tidal deformabilities. We demonstrate that while for purely hadronic stiff EOS the obtained maximum mass is inconsistent with the upper limit on this quantity placed by GW170817, the inclusion of the hyperonic and Δ-resonance degrees of freedom, as well as the deconfinement phase transition at sufficiently low density, produces a configuration of stars consistent with this limit. The obtained hybrid star configurations are in the mass range relevant for the interpretation of the GW170817 event. We compare our results for the tidal deformability with the limits inferred from GW170817 showing that the onset of non-nucleonic phases, such as Δ-resonance--hyperon admixed phase and/or the quark phase(s), are favored by this data if the nuclear EOS is stiff. Also, we show that low-mass twins and especially triplets proliferate the number of combinations of possible types of stars that can undergo a merger event, the maximal number being six in the case of triplets. The prospects for uncovering the first-order phase transition(s) to and in quark matter via measurements of tidal deformabilities in merger events are discussed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

NEMA-Phase Compliant Traffic Signal Controller Module in SUMO

The controller modules in SUMO use a stage-based control structure. A phase is defined as a stage of all allowed movements at a time instance. However, traffic signal controllers used in North America widely use National Electrical Manufacturers Association (NEMA) phase definition. A NEMA phase is defined by a certain flow movement at an intersection. At one time, more than one NEMA phase could happen together as long as they do not conflict with each other. We can visualize the NEMA phases and timings in Ring-and-Barrier structured NEMA diagrams. For one controller, only one phase from a ring can be activated at a time. Phases from different rings could be activated together as long as they are not from the different sides of a barrier. When a controller is operated in fixed-time control mode, we can model the NEMA phase timing as a corresponding stage-based control timing without any issues. When introducing actuation into the signal control, a Ring-and-Barrier structured traffic signal controller can be more flexible than stage-based controller by allowing different possible phase combinations. We made two efforts in modeling Ring-and-Barrier structured controllers in SUMO. One is to translate a NEMA phases timing into SUMO-readable phases and timings as an additional file for SUMO. This translation worked well for fixed-time control. To model actuated control and coordinated actuated control, we augmented the SUMO source code by adding a Ring-and-Barrier structured controller module. This module could implement traffic signal timing from controllers using NEMA phases. We also augmented TraCI to be able to set new NEMA phase timings during simulations. We examined the Ring-and-Barrier structured traffic signal controller module by both visually observing the simulation animations and the simulation records. The developed control module can model the generalized Ring-and-Barrier structured traffic signal timing that is used in North America. SEE: https://github.com/eclipse/sumo/blob/main/src/microsim/traffic_lights/NEMAController.cpp

Wang, Qichao↗
DOE OSTI2020

Fundamental Behavior of ENSO Phase Locking

El Niño–Southern Oscillation (ENSO) events tend to peak at the end of the calendar year, a phenomenon called ENSO phase locking. This phase locking is a fundamental ENSO property that is determined by its basic dynamics. The conceptual ENSO recharge oscillator (RO) model is adopted to examine the ENSO phase-locking behavior in terms of its peak time, strength of phase locking, and asymmetry between El Niño and La Niña events. The RO model reproduces the main phase-locking characteristics found in observations, and the results show that the phase locking of ENSO is mainly dominated by the seasonal modulation of ENSO growth/decay rate. In addition, the linear/nonlinear mechanism of ENSO phase preference/phase locking is investigated using RO model. The difference between the nonlinear phase-locking mechanism and linear phase-preference mechanism is largely smoothed out in the presence of noise forcing. Further, the impact on ENSO phase locking from annual cycle modulation of the growth/decay rate, stochastic forcing, nonlinearity, and linear frequency are examined in the RO model. The preferred month of ENSO peak time depends critically on the phase and strength of the seasonal modulation of the ENSO growth/decay rate. Furthermore, the strength of phase locking is mainly controlled by the linear growth/decay rate, the amplitude of seasonal modulation of growth/decay rate, the amplitude of noise, the SST-dependent factor of multiplicative noise, and the linear frequency. The asymmetry of the sharpness of ENSO phase locking is induced by the asymmetric effect of state-dependent noise forcing in El Niño and La Niña events.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Determining the effects of U/Pu ratio on subsolidus phase transitions in U-Pu-Zr metallic fuel alloys

Here, ternary alloys consisting primarily of uranium, plutonium, and zirconium (U-Pu-Zr) are among the leading candidate fuel systems considered for fast spectrum nuclear reactors. Despite historical operation data from the testing of U-Pu-Zr rods in the Experimental Breeder Reactor-II, considerable uncertainty about the evolution of phases and microstructure across the ternary composition space exists. Due to sluggish kinetics and other difficulties in handling metal actinide specimens, quantitative measurements of phase-transitions in U-Pu-Zr alloys remain sparse in scientific literature, with most investigators reporting either phase-transition temperatures or phase identification data, but not both from the same specimens. The purpose of this paper is to critically compare experimental and calculated phase transition data and correlate with the microstructure and phase characterization data of as-cast and annealed U-Pu-Zr alloys. Phase transition peaks were measured using differential scanning calorimetry in the subsolidus regions (723-948 K) of three ternary U-Pu-Zr alloys with the same zirconium concentration but various U/Pu ratios. Overlapping peaks were deconvoluted using a Frazier-Suzuki peak fitting algorithm, and the critical peak temperatures and enthalpies were calculated. In general, increasing concentrations of Pu were associated with enhanced thermal stability of the body-centered cubic γ phase upon both heating and cooling. Experimental phase transition temperatures in this study tended to agree well with the predictions of the established ternary phase diagrams and other reported phase transition temperatures in literature. Additionally, the TAF-ID thermodynamic database was used to calculate a U-Pu-40 at.% Zr pseudobinary diagram as well as ternary diagrams from 773 to 973 K. The equilibrium phase transition temperatures tended to be considerably lower than measured peak temperatures upon both heating and cooling. Recommendations for improving the quality of data in future U-Pu-Zr characterization studies are also discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Non-equilibrium states and interactions in the topological insulator and topological crystalline insulator phases of NaCd4As3

Topological materials are of great interest because they can support metallic edge or surface states that are robust against perturbations, with the potential for technological applications. Here, we experimentally explore the light-induced non-equilibrium properties of two distinct topological phases in NaCd4As3: a topological crystalline insulator (TCI) phase and a topological insulator (TI) phase. This material has surface states that are protected by mirror symmetry in the TCI phase at room temperature, while it undergoes a structural phase transition to a TI phase below 200 K. After exciting the TI phase by an ultrafast laser pulse, we observe a leading band edge shift of >150 meV that slowly builds up and reaches a maximum after ∼0.6 ps and that persists for ∼8 ps. The slow rise time of the excited electron population and electron temperature suggests that the electronic and structural orders are strongly coupled in this TI phase. It also suggests that the directly excited electronic states and the probed electronic states are weakly coupled. Both couplings are likely due to a partial relaxation of the lattice distortion, which is known to be associated with the TI phase. In contrast, no distinct excited state is observed in the TCI phase immediately or after photoexcitation, which we attribute to the low density of states and phase space available near the Fermi level. Our results show how ultrafast laser excitation can reveal the distinct excited states and interactions in phase-rich topological materials.

Angle-resolved photoemission spectroscopy↗
DOE OSTI2021

Metastable–solid phase diagrams derived from polymorphic solidification kinetics

Nonequilibrium processes during solidification can lead to kinetic stabilization of metastable crystal phases. A general framework for predicting the solidification conditions that lead to metastable-phase growth is developed and applied to a model face-centered cubic (fcc) metal that undergoes phase transitions to the body-centered cubic (bcc) as well as the hexagonal close-packed phases at high temperatures and pressures. Large-scale molecular dynamics simulations of ultrarapid freezing show that bcc nucleates and grows well outside of the region of its thermodynamic stability. An extensive study of crystal–liquid equilibria confirms that at any given pressure, there is a multitude of metastable solid phases that can coexist with the liquid phase. We define for every crystal phase, a solid cluster in liquid (SCL) basin, which contains all solid clusters of that phase coexisting with the liquid. Additionally, a rigorous methodology is developed that allows for practical calculations of nucleation rates into arbitrary SCL basins from the undercooled melt. It is demonstrated that at large undercoolings, phase selections made during the nucleation stage can be undone by kinetic instabilities amid the growth stage. On these bases, a solidification–kinetic phase diagram is drawn for the model fcc system that delimits the conditions for macroscopic grains of metastable bcc phase to grow from the melt. We conclude with a study of unconventional interfacial kinetics at special interfaces, which can bring about heterogeneous multiphase crystal growth. A first-order interfacial phase transformation accompanied by a growth-mode transition is examined.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Development of Ti 3 SiC 2 MAX phase tubular structures for solar receiver applications

Solar receiver tubes are key components of concentrating solar-thermal power (CSP) systems that harvest solar energy. For better efficiency, the Gen3 CSP receivers, which collect heat into a heat transfer fluid, require a temperature exceeding 700 °C during operation and need to perform under extreme conditions of high temperature and high thermal stress. Operators are seeking CSP designs using new high-temperature structural materials with high thermal conductivity and high creep resistance to achieve a design life of 30 years and thus help recover the plant capital cost sooner. MAX phase materials, which consist of an early transition metal element, an A-group element, and carbon or nitrogen, are expected to exhibit high creep resistance as well as high fracture toughness. Here, in this paper, we describe fabricating both (1) dense Ti 3 SiC 2 MAX phase disks and (2) short-length tubes using field-assisted sintering technology (FAST). First, the disk samples that we fabricated are fully dense and contain ≈90 % Ti 3 SiC 2 MAX phase materials and ≈10 % TiC phase materials. We determined a flexure strength of 519 ± 32 MPa by conducting a four-point bending test at room temperature with rectangular bar samples of ≈100 % density. The thermal conductivity of the Ti 3 SiC 2 MAX phase samples, measured by light flashing analysis, decreases linearly from a value of 41 W . m -1 . K -1 at room temperature to a value of 36 W . m -1 . K -1 at 650 °C. A solar reflectance measurement of the Ti 3 SiC 2 MAX phase revealed that, temperature increases from 400 to 1400 °C, thermal emittance increases from 0.39 to 0.49, while selectivity decreases from 1.8 to 1.4, respectively. Whereas the surface oxidized MAX phase samples after 100 h exposure to air at 1000 °C exhibit that of SiC. Next, we discuss fabrication of the crack-free Ti 3 SiC 2 MAX phase tubular structures accomplished by using FAST processing in graphite bedding. A Ti 3 SiC 2 MAX phase content of > 95 % with traceable ≈3% remaining TiC phase and ≈15 % porosity were demonstrated after high-temperature annealing. An average fracture strength of ≈250 MPa was determined with Ti 3 SiC 2 MAX phase tubes of ≈85 % density by diametral compression testing at room temperature. Our work demonstrated that using FAST processing to produce Ti 3 SiC 2 MAX phase tubular structures for CSP receiver applications is a viable approach.

14 SOLAR ENERGY↗
DOE OSTI2024

Surveying Phase Modifier Functional Groups for Applications to Ln(III) Separations

The application of N,N,N',N'-tetraoctyl diglycolamide (TODGA) in solvent extraction systems for lanthanide (Ln) separations is well understood. In these systems, the formation of a third phase has motivated the use of phase modifiers to enable higher concentrations of H + and Ln common to industrial processes. Several different phase modifiers with applications to diglycolamide (DGA) systems have previously been reported, with a focus on tri-n-butyl phosphate (TBP), N,N'-dihexylactanamide (DHOA), N,N-dioctyl-2-hydroxyacetamide (DOHyA), N,N'-dimethyl-N,N'-dioctylhexylethoxy malonamide (DMDOHEMA), and octanol. While the primary utility of phase modifiers is the increased metal loading, they can have significant effects on the metal distribution ratios, which are well described by the energetics of the extraction process itself. However, the mechanisms by which phase modifiers impact distribution ratios are not generally understood. This work considers the ability of phase modifiers to affect Ln distribution ratios by using phase modifiers with two different functional groups (–Cl and –C≡N) and an octyl alkyl chain in a TODGA and n-dodecane system. Determining the effect of chlorooctane and octane nitrile is important for understanding how phase modifier functional groups and their hydrogen bonding interactions affect Ln extraction. Through combining distribution ratio measurements with organic phase spectroscopic investigations, the impact of chlorooctane and octane nitrile on Ln extraction and their inner-sphere complexes is reported. The addition of either chlorooctane or octane nitrile to TODGA in n-dodecane decreases Ln extraction while maintaining the same inner-sphere Ln complex. The lack of change in inner-sphere Ln-TODGA coordination upon incorporation of phase modifiers and the significant impact of these phase modifiers on distribution ratios suggest the importance of a supramolecular structure. Understanding the role of chlorooctane and octane nitrile on the organic phase structure at longer length scales has been identified as an avenue for future investigations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Machine learning-based interatomic potential development and phase transition analysis of ferroelectric hafnium dioxide

The ferroelectric phase (𝑃⁢𝑐⁢𝑎⁢2 1 , which is in orthorhombic symmetry) of hafnium dioxide (HfO 2 ) has gained much attention due to its potential applications in nanoelectronics and advanced memory devices. However, its complex phase behavior under external stimuli, such as pressure and temperature, remains a subject of intense investigation. This study focuses on developing a machine learning-based interatomic potential (MLIP) that is trained with data from density-functional theory (DFT) calculations to simulate phase transitions and mechanical properties of HfO 2 . The developed MLIP predicts lattice parameters, equations of state, bulk and shear moduli, and elastic constants that closely align with DFT predictions for several phases and at various pressures. Once validated, the MLIP is used to investigate the phase transitions of ferroelectric HfO 2 (𝑃⁢𝑐⁢𝑎⁢2 1 ) under both isobaric and constant stress conditions at elevated temperatures ranging from 200 to 2500 K. We used several complementary methods, including local symmetry identification, radial distribution function, and x-ray diffraction characterization, to identify interesting phase transitions among several competitive hafnia phases predicted from our simulations. The suggested methods uniformly reveal that under pure deviatoric condition, the system favors a transition from the orthorhombic 𝑃⁢𝑐⁢𝑎⁢2 1 phase to a tetragonal (𝑃⁢4 2 /𝑛⁢𝑚⁢𝑐) phase, whereas a zero stress condition drives the system from the 𝑃⁢𝑐⁢𝑎⁢2 1 phase to another orthorhombic (𝑃⁢𝑏⁢𝑐⁢𝑛) phase. These findings provide crucial insights into stress and temperature-induced phase behavior of hafnia, guiding future experimental and theoretical studies for optimizing hafnia-based ferroelectric devices.

Ferroelectric HfO2↗
DOE OSTI2022

Quasiparticle self-consistent GW band structures and phase transitions of LiAlO 2 in tetrahedrally and octahedrally coordinated structures

In this work, a first-principles computational study is presented of various phases of LiAlO 2 . The relative total energies and equations of state of the α, β, and γ phases are determined after structural relaxation of each phase. The β and γ tetrahedral phases are found to be very close in energy and lattice volume with the γ phase having the lowest energy. The octahedral α phase is a high-pressure phase and the transition pressure from the γ and β phases to α is determined to be about 1 GPa. The electronic band structures of each phase at their own equilibrium volume are determined using the quasiparticle self-consistent (QS) GW method as well as using the 0.8 Σ approach in which the QS GW self-energy is reduced by a factor of 0.8 to correct for the underscreening of W in QS GW. The effective masses of the band edges and the nature of the band gaps are presented. The lowest energy γ phase is found to have a pseudodirect gap of 7.69 eV. The gap is direct at Γ but corresponds to a dipole forbidden transition. The imaginary part of the dielectric function and the absorption coefficient are calculated in the long-wavelength limit and the random phase approximation, without local field or electron-hole interaction effects for each phase, and their anisotropies are discussed. Si doping on the Al site is investigated as a possible n-type dopant in γ-LiAlO 2 using a 128-atom supercell corresponding to 3.125% Si on the Al sublattice in the generalized gradient approximation and a smaller 16-atom cell with 25% Si in the QS GW approximation. The Si is found to significantly perturb the conduction band and lower the gap but a clearly separated deep donor defect level is not found. However, the donor binding energy is still expected to be relatively deep, on the order of a few tenths eV in the hydrogenic effective mass approximation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Predicting secondary organic aerosol phase state and viscosity and its effect on multiphase chemistry in a regional-scale air quality model

Atmospheric aerosols are a significant public health hazard and have substantial impacts on the climate. Secondary organic aerosols (SOAs) have been shown to phase separate into a highly viscous organic outer layer surrounding an aqueous core. This phase separation can decrease the partitioning of semi-volatile and low-volatile species to the organic phase and alter the extent of acid-catalyzed reactions in the aqueous core. A new algorithm that can determine SOA phase separation based on their glass transition temperature (T g ), oxygen to carbon (O:C) ratio and organic mass to sulfate ratio, and meteorological conditions was implemented into the Community Multiscale Air Quality Modeling (CMAQ) system version 5.2.1 and was used to simulate the conditions in the continental United States for the summer of 2013. SOA formed at the ground/surface level was predicted to be phase separated with core–shell morphology, i.e., aqueous inorganic core surrounded by organic coating 65.4 % of the time during the 2013 Southern Oxidant and Aerosol Study (SOAS) on average in the isoprene-rich southeastern United States. Our estimate is in proximity to the previously reported ~70 % in literature. The phase states of organic coatings switched between semi-solid and liquid states, depending on the environmental conditions. The semi-solid shell occurring with lower aerosol liquid water content (western United States and at higher altitudes) has a viscosity that was predicted to be 10 2 –10 12 Pa s, which resulted in organic mass being decreased due to diffusion limitation. Organic aerosol was primarily liquid where aerosol liquid water was dominant (eastern United States and at the surface), with a viscosity <10 2 Pa s. Phase separation while in a liquid phase state, i.e., liquid–liquid phase separation (LLPS), also reduces reactive uptake rates relative to homogeneous internally mixed liquid morphology but was lower than aerosols with a thick viscous organic shell. The sensitivity cases performed with different phase-separation parameterization and dissolution rate of isoprene epoxydiol (IEPOX) into the particle phase in CMAQ can have varying impact on fine particulate matter (PM 2.5 ) organic mass, in terms of bias and error compared to field data collected during the 2013 SOAS. This highlights the need to better constrain the parameters that govern phase state and morphology of SOA, as well as expand mechanistic representation of multiphase chemistry for non-IEPOX SOA formation in models aided by novel experimental insights.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Liquid–Liquid Phase Separation in Supermicrometer and Submicrometer Aerosol Particles

The interactions of aerosol particles with light and clouds are among the most uncertain aspects of anthropogenic climate forcings. The effects of aerosol particles on climate depend on their optical properties, heterogeneous chemistry, water uptake behavior, and ice nucleation activity. These properties in turn depend on aerosol physics and chemistry including composition, size, shape, internal structure (morphology), and phase state. The greatest numbers of particles are found at small, submicrometer sizes, and the properties of aerosol particles can differ on the nanoscale compared with measurements of bulk materials. As a result, our focus has been on characterizing the phase transitions of aerosol particles in both supermicrometer and submicrometer particles. The phase transition of particular interest for us has been liquid–liquid phase separation (LLPS), which occurs when components of a solution phase separate due to a difference in solubilities. For example, organic compounds can have limited solubility in salt solutions especially as the water content decreases, increasing the concentration of the salt solution, and causing phase separation between organic-rich and inorganic-rich phases. To characterize the systems of interest, we primarily use optical microscopy for supermicrometer particles and cryogenic-transmission microscopy for submicrometer particles. This Account details our main results to date for the phase transitions of supermicrometer particles and the morphology of submicrometer aerosol. Herein, we have found that the relative humidity (RH) at which LLPS occurs (separation RH; SRH) is highly sensitive to the composition of the particles. For supermicrometer particles, SRH decreases as the pH is lowered to atmospherically relevant values. SRH also decreases when non-phase-separating organic compounds are added to the particles. For submicrometer particles, a size dependence of morphology is observed in systems that undergo LLPS in supermicrometer particles. In the limit of slow drying rates, particles <30 nm are homogeneous and larger particles are phase-separated. This size dependence of aerosol morphology arises because small particles cannot overcome the activation barrier needed to form a new phase when phase separation occurs by a nucleation and growth mechanism. Additionally, the inhibition of LLPS in small particles is observed for mixtures of ammonium sulfate with single organic compounds as well as complex organics like α-pinene secondary organic matter. The morphology of particles affects activation diameters for the formation of cloud condensation nuclei. These results more generally have implications for aerosol properties that affect the climate system. In addition, LLPS is also widely studied in materials and biological chemistry, and our results could potentially translate to implications for these fields.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

New examples of ferroelectric nematic materials showing evidence for the antiferroelectric smectic-Z phase

Abstract We present a new ferroelectric nematic material, 4-((4′-((trans)-5-ethyloxan-2-yl)-2′,3,5,6′-tetrafluoro-[1,1′-biphenyl]-4-yl)difluoromethoxy)-2,6-difluorobenzonitrile (AUUQU-2-N) and its higher homologues, the molecular structures of which include fluorinated building blocks, an oxane ring, and a terminal cyano group, all contributing to a large molecular dipole moment of about 12.5 D. We observed that AUUQU-2-N has three distinct liquid crystal phases, two of which were found to be polar phases with a spontaneous electric polarization P s of up to 6 µC cm –2 . The highest temperature phase is a common enantiotropic nematic (N) exhibiting only field-induced polarization. The lowest-temperature, monotropic phase proved to be a new example of the ferroelectric nematic phase (N F ), evidenced by a single-peak polarization reversal current response, a giant imaginary dielectric permittivity on the order of 10 3 , and the absence of any smectic layer X-ray diffraction peaks. The ordinary nematic phase N and the ferroelectric nematic phase N F are separated by an antiferroelectric liquid crystal phase which has low permittivity and a polarization reversal current exhibiting a characteristic double-peak response. In the polarizing light microscope, this antiferroelectric phase shows characteristic zig-zag defects, evidence of a layered structure. These observations suggest that this is another example of the recently discovered smectic Z A (SmZ A ) phase, having smectic layers with the molecular director parallel to the layer planes. The diffraction peaks from the smectic layering have not been observed to date but detailed 2D X-ray studies indicate the presence of additional short-range structures including smectic C-type correlations in all three phases—N, SmZ A and N F —which may shed new light on the understanding of polar and antipolar order in these phases.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Bypassing the yellow phase for extremely stable formamidinium lead iodide perovskite solar cells

INTRODUCTION Formamidinium lead iodide (FAPI) emerged as an ideal material for single-junction perovskite solar cells owing to its near optimal bandgap of 1.45 to 1.5 eV and outstanding thermal stability. However, the photoactive cubic α-phase (3C-FAPI) of FAPI is structurally unstable and undergoes a reconstructive phase transition to the nonperovskite yellow hexagonal δ-phase (2H-FAPI) at ambient temperature. The phase reconstruction from 3C-FAPI to 2H-FAPI could be prevented by alloying methylammonium (MA) or Cs or both at the A-site and Br at the halide site, but this limits long-term durability owing to phase segregation or materials instability. Addressing these challenges requires a rational design strategy to stabilize 3C-FAPI by restricting lattice reconstruction without compromising thermal stability. RATIONALE Two main strategies have emerged to improve the phase stability and film quality of FAPI. Here, the first is a lattice-templating approach, which enables the slow formation of perovskite but it eventually degrades through the formation of yellow phases. The second approach, which has been widely explored, involves additive engineering, using alkyl ammonium halide or mostly chloride-based additives, which provide better control over the crystallization route. However, the FAPI films fabricated using these additives are often alloyed and compromise long-term stability. Moreover, the exact role of Cl has been unclear and speculative, specifically when Cl-based additives are used. Even after using a high additive concentration, the incorporation of Cl in perovskite lattice is rare. RESULTS Guided by synergistic modeling and experimental studies, we developed a coadditive strategy using 15 mol % FACl and 0.5 mol % BA 2 PbI 4 perovskites in combination (where BA is butylammonium) to enable a highly oriented (100) Cl-doped FAPI film with exceptional durability. Synchrotron-based in situ wide-angle x-ray scattering revealed a favorable transition for the coadditive-treated FAPI (FAPI-CA) to the corner-sharing 3C black phase through a progressive transformation through the 2H, 4H, 6H, and 8H phases. Moreover, solid-state 35 Cl nuclear magnetic resonance (NMR) revealed Cl incorporation in the perovskite lattice and, as predicted by modeling, indicated that Cl plays a key role in altering the energetics of both the formation and degradation pathways. The Cl-doped perovskite can completely bypass the expected and energetically favorable degradation pathway via the yellow phase or the 2H-PbI 2 phase. Instead, it undergoes degradation only upon exposure to harsh conditions such as 15-sun illumination and 90°C through the energetically uphill 3R-PbI 2 phase path. A p-i-n device fabricated with FAPI-CA film demonstrated a power conversion efficiency (PCE) of 25.1% with an average of 24.1% (40 devices). The notable film stability translated to other devices and retained 98% of its initial PCE under open-circuit conditions at 85° ± 5°C for 1200 hours. CONCLUSION Our study highlights the decisive role of chloride in regulating both the formation and degradation pathways. This regulation is critical for creating a perovskite film with commercially relevant durability.

Garai, Rabindranath [Rice Univ., Houston, TX (Unit↗