Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Phase change”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Incorporation of GTR (generation–transport–recombination) in semiconductor simulations

With the emergence of phase change memory, where the devices experience extreme thermal gradients (~100 K/nm) during transitions between low and high resistive states, the study of thermoelectric effects at small scales becomes particularly relevant. We had earlier observed asymmetric melting of self-heated nano-crystalline silicon micro-wires, where current densities of ~10 7 A/cm 2 were forced through the wires by 1 μs, ~30 V pulses. The extreme asymmetry can be explained by the generation of considerable amount of minority carriers, transport under the electric field, and recombination downstream, a heat transfer process we termed as generation–transport–recombination, which is in opposite direction of the electronic-convective heat carried by the majority carriers. Here, we present a full semiconductor physics treatment of this carrier-lattice heat transport mechanism and the contribution of the minority carriers on the evolution of the melt–solid interface, which can be applied to various high-temperature electronic devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Iso-cost-performance of thermal energy storage

As thermal energy storage (TES) systems gain increasing recognition as next-generation energy storage solutions, evaluating their techno-economic performance is crucial. This perspective analyzes the cost-performance of latent heat-based TES systems and introduces the concept of iso-cost-performance—maintaining a constant cost per unit energy ($\$$/kWh) despite material degradation. Using an empirical degradation model, we show that after 1200 thermal cycles, the thermal conductivity and volumetric energy density of a paraffin-based phase change material (PCM) decreased by 36.0% and 26.1%, respectively, resulting in a 31.2% reduction in the figure of merit (FOM) and, consequently, the system cost-performance. However, by introducing thermally conductive additives to enhance effective thermal conductivity, the TES system can recover its initial FOM, achieving iso-cost-performance operation. This framework quantitatively demonstrates how degradation-mitigation strategies—such as improving thermal conductivity—can offset material degradations and maintain long-term cost-effectiveness. Beyond PCM-based TES, the proposed FOM-based approach provides a generalized pathway for cost-performance optimization across various TES technologies.

25 ENERGY STORAGE↗
DOE OSTI2025

Demonstration and characterization of insertable passive thermal switches for dynamic building envelopes

A dynamic building envelope integrated with thermal energy storage, such as phase change material (PCM), is an emerging technology that offers a promising solution to improve the energy efficiency of buildings. This study reports the development of insertable thermal switches, which modulate thermal resistance, thereby making building envelopes dynamic and enhancing the use of free ambient heating and cooling. The reported thermal switches are passive, meaning they work solely based on indoor and outdoor temperatures. A single switch when inserted into 10 × 10-in (0.064-m 2 ) XPS foam board insulation demonstrates effective thermal conductivity of 0.050 W/m-K in the resistive state and 0.285 W/m-K in the conductive state. Thermal switches exhibit an effective switching ratio of 5.7, with no noticeable degradation in performance over 770 cycles. Additionally, when integrated into a wall sample containing a PCM layer, switches significantly reduce the PCM solidification time by 43.2% during the cooling process.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Incorporating PCM-enabled thermal energy storage into 3D printable cementitious composites

This paper delineates the feasibility of incorporating microencapsulated phase change materials (mPCM) into 3D printable cementitious composite materials. A comprehensive experimental program was carried out to evaluate the impacts of mPCM on the printability, microstructures, mechanical and thermal properties of cementitious 3D printing ‘inks’. Results showed that the mPCM affected the printability of the cementitious ink material based on its physical properties (e.g., particle size) and volume loading – at lower volume loadings, mPCM increased the flowability of the cementitious ink material while leading to increased compressive strength and thermal conductivity for the hardened printed material. However, further increase in mPCM dosage led to a decrease in printability and, therefore, decrease in compressive strength and thermal conductivity as compared to the reference mixture. Here the results also showed that the inclusion of mPCM influence the printing parameters. In general, the inclusion of higher volume contents of mPCM necessitates a higher extrusion rate to achieve a desirable extrudability. Lastly, a thermal network model was formulated for 3D printed mPCM charged building components (e.g., wall). The study shows that microencapsulated PCM materials have good potential to be used in 3D printable cementitious mixtures for improving the thermal and energy performance of 3D printed buildings.

36 MATERIALS SCIENCE↗
DOE OSTI2020

First-principles study and experimental characterization of metal incorporation in germanium telluride

Germanium telluride is a well-known phase change material (PCM) used in non-volatile memory cells and radio frequency switches. Controlling the properties of GeTe for improved PCM device performance has sometimes been achieved by doping and/or alloying with metals, often at concentrations greater than 10 at. % and using non-equilibrium methods. Here, since switching PCMs between the low-resistance crystalline and high-resistance amorphous states requires a heating cycle, the stability of metal-incorporated GeTe (Ge 0.5–x M x Te 0.5 ) films is also critical to practical implementation of these materials in electronic and optoelectronic devices. In this work, we use both density-functional theory and experimental characterization methods to probe the solubility and critical properties of Ge 0.5–x M x Te 0.5 films. Using first-principles calculations, we determine the enthalpy of formation for GeTe with 2.08, 4.17, and 6.25 at. % of Cu, Fe, Mn, Mo, and Ti and show trends between the stability of the Ge 0.5–x M x Te 0.5 systems and the atomic position, composition, and distribution of the metal atoms in the GeTe matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermal coupling-decoupling mechanism of heat transfer across van der Waals interfaces in n-eicosane

Progress toward improving thermal transport properties of n-eicosane, a promising phase change material for thermal energy storage near human body temperature, is hindered by lack of a general theoretical framework to model thermal interfacial conductance (TIC) of the van der Waals (vdW) force bonded molecular interfaces, which have little compositional/structural mismatch. Combining molecular dynamics simulations at temperatures up to the melting point and a time-domain analysis of interfacial heat currents in individual molecules, we unveil that (1) the heat flux across a molecular vdW interface has an alternating coupling-decoupling pattern at the single molecule level due to thermal fluctuations, and (2) the net heat transfer during the thermally coupled periods is orders of magnitude larger than that during the thermally decoupled periods. Furthermore, we demonstrate that a vdW interface's TIC correlates almost linearly with two atomistic-scale coupling-decoupling parameters: αc and σc, that represent the duration and strength of the thermal coupling, respectively. This thermal coupling-decoupling mechanism proposes a new paradigm that explicitly accounts for the effects of structural flexibility and dynamical fluctuation on heat transfer across molecular interfaces, and will likely provide new insights into modeling thermal transport properties in a wide-ranging soft materials, including self-assembled monolayers, paraffins or lipids.

42 ENGINEERING↗
DOE OSTI2022

Micro-Environmental Control System (Final Report)

This project developed an innovative micro-environmental control system (µX) that enables office buildings to reduce energy used for heating and cooling by 15% or more. The µX is a compact, quiet, and ergonomic device that is designed to be installed under an office workstation; it is designed to maintain occupant comfort when room thermostat setpoints are incremented by 4°F or more (warmer in the summer and cooler in the winter) to save energy. When ambient room temperatures are outside of the usual comfort range, the µX maintains occupant comfort by delivering personalized cooling or heating locally to each office worker. The µX provides personalized cooling using a micro vapor compression system that includes a new high-performance micro-scroll compressor and a novel thermal storage unit. The vapor compression system operates at night to freeze a phase-change material (PCM). During the workday, the cooling stored in the PCM is released as a cool breeze of air to make occupants more comfortable. The micro-scroll compressor was developed specifically for this application; it is smaller than any of its type, minimizing the amount of power needed. In heating mode, the µX maintains occupant comfort using a foot heating mat with an infrared reflective box. The µX R&D project was conducted by Syracuse University in collaboration with United Technologies Research Center, Air Innovations, Bush Technical, and Cornell University. Over the course of the initial three-year project, the team developed and evaluated four versions of the unit, advancing the concept to Technology Readiness Level 6. The capabilities of individual proof-of-concept prototypes were verified in tests that were conducted with: 1) units in psychrometric chambers, 2) an instrumented manikin in a laboratory, and 3) human subjects in laboratories that simulate office environments. The tests verified that the µX prototypes met or exceeded all performance targets required to enable office buildings to reduce energy used for heating and cooling by 15% or more by maintaining occupant comfort when thermostat setpoints are incremented by 4°F or more.

25 ENERGY STORAGE↗
DOE OSTI2022

Atomistic insights into the heat conductance across the interfaces between erythritol and different metals: A non-equilibrium molecular dynamics study

The heat conductance across the interface between a phase change material (PCM) and the metal shell is important for thermal design of latent heat storage systems. Non-equilibrium molecular dynamics simulations were carried out in this work to unravel, at the atomistic level, the interfacial heat conductance mechanisms between erythritol (the most promising medium-temperature polyol PCM) and two different metals (i.e., copper and aluminum). The interfacial contact ratio was introduced as a parameter to represent different contact conditions at the interfaces, for example, different surface roughness levels of the metals. It was found that with the increase of interfacial contact ratio, the temperature difference between the erythritol/metal interfaces decreases, whereas the interfacial heat transfer coefficient increases gradually. At the perfect contact condition, i.e., the interfacial contact ratio reaches 100%, the interfacial heat transfer coefficients across the erythritol/Cu and erythritol/Al interfaces were predicted to be 398 ± 26 MW/m 2 K and 544 ± 11 MW/m 2 K, respectively. The interfacial heat conductance of erythritol/Al is better than that of erythritol/Cu. The mismatch of atomic spectral density across the interfaces between erythritol and the two metals was analyzed and distinguished. These results could guide the selection of packaging materials and the thermal design of erythritol-based latent heat storage systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Techno-Economic Optimization of Advanced Energy Plants with Integrated Thermal, Mechanical, and Electro-Chemical Storage (Final Report)

The increasing use of renewable energy sources is leading to increased cycling of fossil-fueled power plants (FFPP) that are designed to operate at base-loaded conditions. Integrating energy storage facilities with the FFPPs can be helpful in reducing load-following operation of FFPPs. Decentralized deployment of energy storage facilities at the FFPP level has considerable advantages due to possibilities of smaller storage capacities, immediate benefits realized by the host power plant due to the increase in the efficiency, cleaner emission and higher plant life to name a few. Most importantly, deployment at the FFPP level can exploit the existing equipment items and facilities at the host power plant, thus reducing the CAPEX and reducing the storage capacity. However, realization of these benefits will critically depend on novel configuration/integration strategies with the least impact on the power plant operation and its configuration. Furthermore, dynamics of the entire integrated system including both the FFPP and the storage technologies must be taken into account to obtain the cost-optimal solution. With these motivations, the objective of this project was to complete a focused evaluation of decentralized deployments of energy storage facilities at the FFPP level. Promising thermal, chemical, mechanical, and electro-chemical storage technologies were evaluated with due consideration of their transient response to obtain various optimal system concepts that can minimize the levelized cost of storage. For thermal storage, cryogenic energy storage along with high temperature heat storage in molten salt as well as phase change material were evaluated. For mechanical storage, cryogenic air storage and pumped hydro storages were evaluated. For chemical storage, hydrogen storage was evaluated. For electrochemical storage, the team evaluated sodium sulfur, vanadium redox flow battery as well as Li-ion batteries. Integration of these storage technologies with the natural gas combined cycle (NGCC) and supercritical pulverized coal (SCPC) plants was considered. Six technologies, namely molten salt, cryogenics, compressed air, pumped hydro, H2 storage and Li-ion battery storage, were downselected based on their levelized cost of storage. It was observed that the ranking of the optimal storage technology can differ based on the host power plant technology even when same demand/supply/price profile for electricity are considered. It was also observed that as the variability in power demand varies, the ranking of the optimal storage technologies vary. However, for the same demand and LMP profile, top six optimal storage technologies for NGCC vs SCPC plants did not differ much even though LCOS for the same technology and optimal size of a given storage technology did differ. Detailed techno-economic assessment of these six technologies was undertaken.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Differences in Sb 2 Te 3 growth by pulsed laser and sputter deposition

High quality van der Waals chalcogenides are important for phase change data storage, thermoelectrics, and spintronics. Using a combination of statistical design of experiments and density functional theory, we clarify how out-of-equilibrium van der Waals epitaxial deposition methods can improve the crystal quality of Sb 2 Te 3 films. We compare films grown by radio frequency sputtering and pulsed laser deposition (PLD). The growth factors that influence the crystal quality for each method are different. For PLD grown films a thin amorphous Sb 2 Te 3 seed layer most significantly influences the crystal quality. In contrast, the crystalline quality of films grown by sputtering is rather sensitive to the deposition temperature and less affected by the presence of a seed layer. This difference is somewhat surprising as both methods are out-of-thermal-equilibrium plasma-based methods. Non-adiabatic quantum molecular dynamics simulations show that this difference originates from the density of excited atoms in the plasma. The PLD plasma is more intense and with higher energy than that used in sputtering, and this increases the electronic temperature of the deposited atoms, which concomitantly increases the adatom diffusion lengths in PLD. In contrast, the adatom diffusivity is dominated by the thermal temperature for sputter grown films. These results explain the wide range of Sb 2 Te 3 and superlattice crystal qualities observed in the literature. Finally, these results indicate that, contrary to popular belief, plasma-based deposition methods are suitable for growing high quality crystalline chalcogenides.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Experimental characterization of a triply periodic minimal surface PCM-to-air thermal energy storage device

Here, the expansion of energy production has intensified research into thermal energy storage (TES) to manage variability and improve system efficiency. Heat exchanger design is critical to achieving high power densities in TES systems. This study presents a high-surface-area phase change material (PCM)-to-air heat exchanger fabricated via resin-based stereolithography with a novel gyroid-based geometry tailored for enhanced performance. Material properties of the commercial PCM and resin were characterized using analytical techniques. A controlled air loop was used to evaluate heat transfer and pressure drop at various flow rates and inlet temperatures. Results show a strong dependence on the inlet temperature difference (ΔT) relative to the PCM melting point. During charging at the highest flow rate, increasing the inlet air temperature from ΔT = 5 °C to 20 °C above the melting point increased the average heat transfer rate by 187%. During discharging, decreasing the inlet temperature by the same ΔT below the melting point led to a 232% increase. Notably, the high-surface-area design enabled nearly symmetric charging and discharging behavior, a novel result for PCM-based TES systems which are often restricted by natural convection and other effects. The overall heat transfer coefficient was calculated and compared to values from standard design correlations. The maximum thermal effectiveness reached 95% at ΔT = 20 °C and a moderate flow rate of 34 m 3 /h. Peak coefficients of performance (COP) of 7 during charging and 6.4 during discharging were observed at ΔT = 20 °C and a low flow rate of 20 m 3 /h. These results demonstrate the viability of additively manufactured geometries for advanced TES applications.

25 ENERGY STORAGE↗
DOE OSTI2025

Nature-inspired lotus-shaped fins combined with hybrid nanoparticles and metal foam for high-performance latent heat thermal energy storage

Latent heat thermal energy storage (LHTES) systems play a critical role in renewable energy integration by providing high energy density and nearly isothermal operation during phase transitions. However, their performance is often limited by slow melting/charging rates, which motivates the search for enhanced heat transfer designs. This study investigates the melting behavior of RT-82 phase change material (PCM) using novel lotus-shaped fins combined with copper metal foam and conductive graphene nanoparticles and carbon nanotubes. A two-dimensional enthalpy-porosity model in ANSYS Fluent was developed to simulate the charging/melting process, capturing non-thermal equilibrium between the foam and PCM/nano-PCM. In this study, effects of fin geometry, nanoparticle concentration, and foam porosity on melting dynamics and cost-performance trade-offs were investigated. Results showed that natural convection accelerated melting by ~12% compared to conduction-only scenarios. Optimized lotus-shaped fins with higher fin density (T3F4 and T3F10) achieved up to 63% faster melting relative to sparse configurations. Graphene nanoparticles improved thermal conductivity, with a 6% volume fraction, by reducing melting time by ~6.9%, while their combination with 75% porosity foam achieved a maximum reduction in the melting time of ~51% compared to pure PCM. Cost-performance analysis identified T3F4 as the most balanced design, offering rapid thermal response without excessive material costs, while moderate-density designs like T3S6 provided economical alternatives with acceptable performance. These results highlight the performance enhancement that can be achieved by integrating bio-inspired fins, nanoparticles, and foams, into compact and efficient LHTES for solar heating, building thermal management, and industrial waste-heat recovery applications.

25 ENERGY STORAGE↗
DOE OSTI2026

Harnessing Ocean Thermal Gradients Using Thermoelectric Based Submersibles for Ocean Power Applications

The urgent need for energy solutions in marine environments has accelerated the development of innovative technologies capable of leveraging natural resources for power generation. This study introduces a buoyancy-driven submersible system designed to harness ocean thermal gradients using thermoelectric generators (TEGs) and phase change materials (PCMs). The technology aims to provide autonomous power to offshore aquaculture farms, unmanned underwater vehicles (UUVs), offshore platform illumination, and ocean sensors, significantly reducing dependence on fossil fuels. Ocean thermal gradients, especially prevalent in mid-latitude regions, exhibit temperature differences between surface and deep waters ranging from 7 degrees Celsius to 30 degrees Celsius depending on seasonal variations. The proposed submersible technology utilizes TEGs to convert thermal energy from these gradients into electrical power, generating between 0.2 and 0.5 watts, while PCMs are employed to store and regulate this energy, ensuring a stable and continuous power supply. The buoyancy-driven mechanism of the submersible enhances its capability to navigate through varying depths, optimizing its exposure to different thermal gradients and maximizing energy harvesting. The performance of this submersible system is analyzed through detailed thermodynamic assessments and computational fluid dynamics (CFD) modeling focused on heat transfer. These analyzes consider real-world ocean temperature profiles and seek to refine the interaction between TEGs and PCMs to optimize energy extraction. The evaluation encompasses several key performance metrics, including power output and energy efficiency. Results confirm the potential of this innovative technology to provide a continuous and reliable power source for marine applications. By demonstrating the feasibility of using ocean thermal gradients for energy generation, this study contributes to the broader efforts of innovation in energy technologies for harsh, remote marine environments. The implementation of such promises is significant advancements in the autonomy of marine operations. The ongoing research will further investigate scalability ensuring that the system can be effectively adapted to various marine settings and operational demands.

16 TIDAL AND WAVE POWER↗
DOE OSTI2024

Effective direct steam regeneration of bis-iminoguanidine solid sorbent used for carbon dioxide capture

A cost-effective, energy-efficient sorbent regeneration process for phase-changing guanidines used for CO 2 capture was developed based on direct-steam stripping. This approach enhances the regeneration rate, simplifies the overall CO 2 capture process, and reduces the energy cost compared to conventional conductive thermal regeneration. A direct-steam sorbent regeneration reactor was developed, demonstrating that aqueous bis(iminoguanidines) (BIG) sorbents, e.g., methylglyoxal-bis(iminoguanidine) (MGBIG) and glyoxal-bis(iminoguanidine) (GBIG), could be efficiently regenerated with up to ~ 99 % CO 2 recovery through direct-steam stripping. Using low-temperature steam at 100 °C, a 4.5 times faster regeneration rate for GBIG carbonate sorbent (e.g., 30 min for 10 g) was demonstrated compared to conductive-heating (e.g., 135 min for 10 g) at 130 °C. Additionally, fully regenerated MGBIG converts into an aqueous MGBIG solution when the steam condenses onto the sorbent surface. Condensed steam with the guanidine can be easily recycled as an aqueous solution into the gas–liquid contactor to achieve a continuous-flow CO 2 -capture process. Molecular dynamics simulation was employed to provide a better understanding of the process. Higher heat transfer rates from steam to guanidine carbonate, compared to air heating, were attributed to the vibration resonance of water molecules within MGBIG with that of vapor molecules and the effective transfer of kinetic energy from vapor to solid. Technoeconomic analysis demonstrated that direct-steam stripping significantly decreases the CO 2 capture cost by 50 % compared to traditional conductive heating methods. Further, enhanced mass transfer facilitated by low-temperature steam and subsequent condensation effectively heats up the H 2 O-containing BIG-carbonate crystals, facilitating the desorption of CO 2 from the solid crystals, thereby leading to fast, effective, and energy-efficient sorbent regeneration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

The high explosives & affected targets (HEAT) dataset

Artificial Intelligence (AI) surrogate models offer a computationally efficient alternative to full-physics simulations, yet no existing datasets are publicly available for training, testing, and validation of machine learning models of the dynamics of high-explosive driven shocks through multiple materials. Shock propagation through materials is a computationally challenging problem because simulations must include material-specific equations of state (EOS) along with descriptions of other physical processes such as plastic deformation, phase change, damage processes, fluid instabilities, and multi-material interactions. Shocks are typically initiated by high-velocity impacts or explosive loading. The latter case necessitates the addition of models of reactive materials to represent high-explosive (HE) detonation. Here, to address the lack of an expansive dataset for multi-material shock propagation in the AI/ML community, we present the High-Explosives and Affected Targets (HEAT) Dataset. HEAT is a physics-rich collection of two-dimensional, cylindrically symmetric, simulations generated using an Eulerian, multi-material, shock-propagation code developed at Los Alamos National Laboratory. The dataset includes two partitions: (1) the expanding shock-cylinder (CYL) simulations, Figs. 1, and (2) the Perturbed Layered Interface (PLI) simulations, Fig. 2. Entries in both partitions consist of time series of arrays of thermodynamic fields (pressure, density, and temperature), kinematic fields (position and velocity), and additional fields that depend on thermodynamic and/or kinematic fields (e.g., material stress). Materials in the CYL partition include solids (aluminium, copper, depleted uranium, stainless steel, tantalum, and a generic polymer), a liquid (water), gases (air, nitrogen), and a generic detonating material (high explosive, HE). The PLI partition spans a highly varying geometry but consists of fixed materials across entries: Copper, aluminium, stainless steel, generic polymer, and generic HE. HEAT captures critical phenomena such as momentum transfer, shock propagation, plastic deformation, and thermal effects, making HEAT a valuable benchmark for development of AI/ML emulation of multi-material shock propagation.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Dual Purpose – Heating & Cooling – Thermal Battery for Flexible and Energy-Efficient Heat Pump Systems

The integration of heat pumps with thermal energy storage (HP-TES) systems is gaining attention as a viable solution for managing peak building demand driven by immense cooling and heating loads. With growing reliance on renewable energy sources, thermal energy storage offers an excellent opportunity to mitigate mismatches in thermal load between energy supply and demand. The use of phase-change material (PCM) TES is especially promising, as PCMs offer significant latent energy storage capacity with smaller temperature glides in smaller volumes compared to other TES technologies. However, challenges arise because current HP-TES architectures can load-shift only cooling or heating, not both, requiring two systems and thus doubling cost, weight, and footprint. Furthermore, current research efforts lack specific tools and techniques to advance integrated systems from concept design to end-user application, focusing on only discharge performance. To address these challenges, this research proposes a dual-mode (heating and cooling) integrated HP-TES system that uses room-temperature PCM-TES as a high-temperature heat source in heating mode and a low-temperature heat sink in cooling mode, thereby reducing temperature lifts and compressor power. Design criteria for PCM-TES heat exchangers were developed, balancing thermal-hydraulic performance with practical constraints such as available building space and weight requirements along with PCM selection considerations such as shipping conditions, moisture exposure, and number of available cycles. A detailed transient model for HP-TES systems was developed to enable rapid annual performance assessments in any US climate zone.

42 ENGINEERING↗
DOE OSTI2020

Robust control of the minima of high-order harmonics by fine-tuning the alignment of CO 2 molecules for shaping attosecond pulses and probing molecular alignment

In a recent paper, we reported that the position and depth of the minima in the harmonic spectra of CO 2 molecules can be dramatically manipulated by a slight change of the degree of alignment, thus providing a convenient method of shaping attosecond pulses which could lead to the splitting of a typical single attosecond burst into two. Here, we demonstrate that harmonic minima can also be dramatically controlled by changing the pump-probe angles to shape attosecond pulses. In the meanwhile, since the pump-probe angle-dependent harmonic spectra are very sensitive to the degree of alignment, harmonic spectra can also be used to calibrate the alignment distribution of molecules. In this work we identify such robust control of harmonic generation is due to the optical property of CO 2 and the coherent harmonic emission from the oriented molecules. The photoionization transition dipoles (PITDs) of CO 2 exhibit deep minima that change rapidly with molecular orientations accompanied by large phase changes of π in PITDs, thus leading to strong interference when the dipoles are added up coherently.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2023

Hybrid interatomic potential for Sn

To design materials for extreme applications, it is important to understand and predict phase transitions and their influence on material properties under high pressures and temperatures. Atomistic modeling can be a useful tool to assess these behaviors. However, this can be difficult due to the lack of fidelity of the interatomic potentials in reproducing this high pressure and temperature extreme behavior. Here, in this work, a hybrid EAM-R—which is the combination of embedded atom method (EAM) and rapid artificial neural network potential—for Tin (Sn) is described which is capable of accurately modeling the complex sequence of phase transitions between different metallic polymorphs as a function of pressure. This hybrid approach ensures that a basic empirical potential like EAM is used as a lower energy bound. By using the final activation function, the neural network contribution to energy must be positive, assuring stability over the whole configuration space. This implementation has the capacity to reproduce density functional theory results at 6 orders of magnitude slower than a pair potential for molecular dynamics simulation, including elastic and plastic characteristics and relative energies of each phase. Using calculations of the Gibbs free energy, it is demonstrated that the potential precisely predicts the experimentally observed phase changes at temperatures and pressures across the whole phase diagram. At 10.2 GPa, the present potential predicts a first-order phase transition between body-centered tetragonal (BCT) β-Sn and another polymorph of BCT-Sn. This structure transforms into body-centered cubic near the experimentally reported value at 33 GPa. Thus, the Sn potential developed in this paper can be used to study complex deformation mechanisms under extreme conditions of high pressure and strain rates unlike existing potentials. Moreover, the framework developed in this paper can be extended for different material systems with complex phase diagrams.

36 MATERIALS SCIENCE↗