Results for “Performance Margins” — Page 21

NASA NTRS1985

Predicted performance benefits of an adaptive digital engine control system of an F-15 airplane

The highly integrated digital electronic control (HIDEC) program will demonstrate and evaluate the improvements in performance and mission effectiveness that result from integrating engine-airframe control systems. Currently this is accomplished on the NASA Ames Research Center's F-15 airplane. The two control modes used to implement the systems are an integrated flightpath management mode and in integrated adaptive engine control system (ADECS) mode. The ADECS mode is a highly integrated mode in which the airplane flight conditions, the resulting inlet distortion, and the available engine stall margin are continually computed. The excess stall margin is traded for thrust. The predicted increase in engine performance due to the ADECS mode is presented in this report.

Burcham, F. W., Jr.↗

NASA NTRS1985

Predicted performance benefits of an adaptive digital engine control system on an F-15 airplane

The highly integrated digital electronic control (HIDEC) program will demonstrate and evaluate the improvements in performance and mission effectiveness that result from integrating engine-airframe control systems. Currently this is accomplished on the NASA Ames Research Center's F-15 airplane. The two control modes used to implement the systems are an integrated flightpath management mode and an integrated adaptive engine control system (ADECS) mode. The ADECS mode is a highly integrated mode in which the airplane flight conditions, the resulting inlet distortion, and the available engine stall margin are continually computed. The excess stall margin is traded for thrust. The predicted increase in engine performance due to the ADECS mode is presented in this report.

Burcham, F. W., Jr.↗

NASA NTRS1978

CF6 jet engine performance deterioration results

The use of the performance baseline from the flight planning manual as a reference to measure changes in cruise fuel flow rates was discussed. For the CF6-6D engine, the introduction of design changes for performance and durability reasons was seen to introduce an average increment relative to this baseline of 3.2% WFM increase at Nl, 2.5% Fn increase at Nl, 0.8% specific fuel consumption (SFC) increase at Fn, and 7 C EGT increase at Nl, while maintaining sufficient SFC margin of the delivered airplane. The effect of revenue service deterioration and performance restoration relative to the reference was shown to be an adder on top of these design effects. A schematic of typical CF6-6D performance through revenue service and airline maintenance is presented in terms of percent cruise SFC relative to an airline datum point (average level upon entering revenue service). The typical changes in SFC margin are shown for airline revenue service through for installations and refurbishments.

Lewis, R. J.↗

NASA NTRS1996

ACTS Rain Fade Compensation

Performance status of the Adaptive Rain Fade Compensation includes: (1) The rain fade protocol is functional detecting fades, providing an additional 10 dB of margin and seamless transitions to and from coded operation; (2) The stabilization of the link margins and the optimization of rain fade decision thresholds has resulted in improved BER performance; (3) Characterization of the fade compensation algorithm is ongoing.

Coney, Thom A.↗

NASA NTRS2002

Performance characteristics of the deep space 1 flight spare ion thruster long duration test, the first 21,300 hours of operation

A long duration test of the DSl flight spare ion thruster (FT2) is presently being conducted at the Jet Propulsion Laboratory. To, date the thruster has accumulated over 23,500 hours of operation, and 190 kg of Xenon propellant, over 230% of the initial design life. The primary objectives of the test include the processing of 200 kg of Xenon propellant, the identification of unknown failure modes, the characterization and drivers of these failure modes, and to measure performance degradation as the thruster wears. The test is fitted with an extensive array of diagnostics to measure engine wear and performance degradation. To date the most notable erosion processes include severe discharge cathode keeper erosion, accelerator grid erosion, reduction in electrical isolation of the neutralizer assembly, and deposit formation within the neutralizer orifice, reducing margin from plume mode. Over the past 23,500 hours of operation, performance degradation has been minimal, and it is anticipated that the above erosion processes will not preclude the thruster from processing over 200 kg of Xenon.

ion thrusters deep space one↗

NASA NTRS1982

The digital autopilot for thrust vector control of the Shuttle Orbital maneuvering system

This paper describes the requirements for and the design, development and performance of the digital autopilots (DAPs) for thrust vector control, utilizing the orbital maneuvering system (OMS) of the Space Shuttle Orbiter. The hardware and software requirements which caused the design to assume its current form are described. Also, the design synthesis, which considered rigid body stability margins, bending and slosh stabilization, guidance loop compensation, off-nominal performance and hardware and software limitations is presented. The performance of the OMS control system is summarized utilizing flight data from the first three Space Transportation System (STS) flights.

Penchuk, A.↗

NASA NTRS2015

Results from Three Years of Ka-band Propagation Characterization at Svalbard, Norway

Over the next several years, NASA plans to launch several earth science missions which are expected to achieve data throughputs of 5-40 terabits per day transmitted from low earth orbiting spacecraft to ground stations. The current S-band and X-band frequency allocations in use by NASA, however, are incapable of supporting the data rates required to meet this demand. As such, NASA is in the planning stages to upgrade its existing Near Earth Network (NEN) polar ground stations to support Ka-band (25.5-27 GHz) operations. Consequently, it installed and operated a Ka-band radiometer at the Svalbard site. Svalbard was chosen as the appropriate site for two primary reasons: (1) Svalbard will be the first site to be upgraded to Ka-band operations within the NEN Polar Network enhancement plan, and (2) there exists a complete lack of Ka-band propagation data at this site (as opposed to the Fairbanks, AK NEN site, which has 5 years of characterization collected during the Advanced Communications Technology becomes imperative that characterization of propagation effects at these NEN sites is conducted to determine expected system Satellite (ACTS) campaign). processing and provide the Herein, we discuss the data three-year measurement results performance, particularly at low elevation angles ((is) less than 10 deg) from the ongoing Ka-band propagation characterization where spacecraft signal acquisition typically occurs. Since May 2011, NASA Glenn Research Center has installed and operated a Ka-band radiometer at the NEN site located in Svalbard, Norway. The Ka-band radiometer monitors the water vapor line, as well as 4 frequencies around 26.5 GHz at a fixed 10 deg elevation angle. Three-year data collection results indicate good campaign at Svalbard, Norway. Comparison of these results with the ITU models and existing ERA profile data indicates very good agreement when the 2010 rain maps and cloud statistics are used. Finally, the Svalbard data is used to derive the expected atmospheric margin requirements for this site agreement with models and comparable performance to necessary to maintain total system availability levels for the previously characterized northern latitude sites in the United States, i.e., Fairbanks, Alaska. The Svalbard data is used to upcoming Joint Polar Satellite System (JPSS) launch in the derive availability results for an upcoming earth-observation 2017/2022 timeframes. mission, JPSS-1, and indicate a requirement of 4 dB of atmospheric attenuation margin necessary to close the link with 99% overall system availability for the expected LEO orbital cycle, as observed from the Svalbard location.

Ka-band↗

NASA NTRS2015

Results from Three Years of Ka-Band Propagation Characterization at Svalbard, Norway

Over the next several years, NASA plans to launch several earth science missions which are expected to achieve data throughputs of 5-40 terabits per day transmitted from low earth orbiting spacecraft to ground stations. The current S-band and X-band frequency allocations in use by NASA, however, are incapable of supporting the data rates required to meet this demand. As such, NASA is in the planning stages to upgrade its existing Near Earth Network (NEN) polar ground stations to support Ka-band (25.5-27 GHz) operations. Consequently, it installed and operated a Ka-band radiometer at the Svalbard site. Svalbard was chosen as the appropriate site for two primary reasons: (1) Svalbard will be the first site to be upgraded to Ka-band operations within the NEN Polar Network enhancement plan, and (2) there exists a complete lack of Ka-band propagation data at this site (as opposed to the Fairbanks, AK NEN site, which has 5 years of characterization collected during the Advanced Communications Technology becomes imperative that characterization of propagation effects at these NEN sites is conducted to determine expected system Satellite (ACTS) campaign). processing and provide the Herein, we discuss the data three-year measurement results performance, particularly at low elevation angles ((is) less than 10 deg) from the ongoing Ka-band propagation characterization where spacecraft signal acquisition typically occurs. Since May 2011, NASA Glenn Research Center has installed and operated a Ka-band radiometer at the NEN site located in Svalbard, Norway. The Ka-band radiometer monitors the water vapor line, as well as 4 frequencies around 26.5 GHz at a fixed 10 deg elevation angle. Three-year data collection results indicate good campaign at Svalbard, Norway. Comparison of these results with the ITU models and existing ERA profile data indicates very good agreement when the 2010 rain maps and cloud statistics are used. Finally, the Svalbard data is used to derive the expected atmospheric margin requirements for this site agreement with models and comparable performance to necessary to maintain total system availability levels for the previously characterized northern latitude sites in the United States, i.e., Fairbanks, Alaska. The Svalbard data is used to upcoming Joint Polar Satellite System (JPSS) launch in the derive availability results for an upcoming earth-observation 2017/2022 timeframes. mission, JPSS-1, and indicate a requirement of 4 dB of atmospheric attenuation margin necessary to close the link with 99% overall system availability for the expected LEO orbital cycle, as observed from the Svalbard location.

near earth network↗

NASA NTRSDate not supplied

Analysis of Alternative Architectures for a 2024 Lunar Sortie

This study focused on performing a broad analysis of lunar architectures to identify key alternatives capable of performing a 2024 human lunar landing mission. The goal of the study was to identify architecture alternatives which exhibit robustness, as measured by launch vehicle payload margin, to absorb the natural growth that occurs during design maturation. The study consisted of up to three element architectures which perform the mission from cis-lunar aggregation, through the surface sortie, and return to cis-lunar space. More than 600,000 data points were evaluated utilizing a novel architecture synthesis framework currently being developed by NASA/MSFC. Key findings from the study indicate that architecture complexity can be reduced by minimizing the number of discrete, unique architecture elements, which in turn translates into reduced design, development, test, and evaluation (DDT&E) complexity. It was identified that heavy lift launch vehicles enable such architectures while also providing significant increases to launch vehicle margin over existing and near-term commercial launch vehicle (CLV) performance expected in the 2024 time frame. Additionally, the study identified storable propellant based lander architectures as leading alternatives in achieving a 2024 human lunar landing by providing reduced technology needs and development schedules.

Architecture Analysis↗

NASA NTRS1977

Study of synthesis techniques for insensitive aircraft control systems

Insensitive flight control system design criteria was defined in terms of maximizing performance (handling qualities, RMS gust response, transient response, stability margins) over a defined parameter range. Wing load alleviation for the C-5A was chosen as a design problem. The C-5A model was a 79-state, two-control structure with uncertainties assumed to exist in dynamic pressure, structural damping and frequency, and the stability derivative, M sub w. Five new techniques (mismatch estimation, uncertainty weighting, finite dimensional inverse, maximum difficulty, dual Lyapunov) were developed. Six existing techniques (additive noise, minimax, multiplant, sensitivity vector augmentation, state dependent noise, residualization) and the mismatch estimation and uncertainty weighting techniques were synthesized and evaluated on the design example. Evaluation and comparison of these six techniques indicated that the minimax and the uncertainty weighting techniques were superior to the other six, and of these two, uncertainty weighting has lower computational requirements. Techniques based on the three remaining new concepts appear promising and are recommended for further research.

Harvey, C. A.↗

NASA NTRS1985

A class of optimum digital phase locked loops for the DSN advanced receiver

A class of optimum digital filters for digital phase locked loop of the deep space network advanced receiver is discussed. The filter minimizes a weighted combination of the variance of the random component of the phase error and the sum square of the deterministic dynamic component of phase error at the output of the numerically controlled oscillator (NCO). By varying the weighting coefficient over a suitable range of values, a wide set of filters are obtained such that, for any specified value of the equivalent loop-noise bandwidth, there corresponds a unique filter in this class. This filter thus has the property of having the best transient response over all possible filters of the same bandwidth and type. The optimum filters are also evaluated in terms of their gain margin for stability and their steady-state error performance.

Hurd, W. J.↗

NASA NTRS1986

Test and evaluation of the HIDEC engine uptrim algorithm

The highly integrated digital electronic control (HIDEC) program will demonstrate and evaluate the improvements in performance and mission effectiveness that result from integrated engine-airframe control systems. Performance improvements will result from an adaptive engine stall margin mode, a highly integrated mode that uses the airplane flight conditions and the resulting inlet distortion to continuously compute engine stall margin. When there is excessive stall margin, the engine is uptrimmed for more thrust by increasing engine pressure ratio (EPR). The EPR uptrim logic has been evaluated and implemented into computer simulations. Thrust improvements over 10 percent are predicted for subsonic flight conditions. The EPR uptrim was successfully demonstrated during engine ground tests. Test results verify model predictions at the conditions tested.

Ray, R. J.↗

NASA NTRS1986

Test and evaluation of the HIDEC engine uptrim algorithm

The highly integrated digital electronic control (HIDEC) program will demonstrate and evaluate the improvements in performance and mission effectiveness that result from integrated engine-airframe control systems. Performance improvements will result from an adaptive engine stall margin mode, a highly integrated mode that uses the airplane flight conditions and the resulting inlet distortion to continuously compute engine stall margin. When there is excessive stall margin, the engine is uptrimmed for more thrust by increasing engine pressure ratio (EPR). The EPR uptrim logic has been evaluated and implemente into computer simulations. Thrust improvements over 10 percent are predicted for subsonic flight conditions. The EPR uptrim was successfully demonstrated during engine ground tests. Test results verify model predictions at the conditions tested.

Ray, R. J.↗

NASA NTRS1992

Design and evaluation of a robust dynamic neurocontroller for a multivariable aircraft control problem

The design of a dynamic neurocontroller with good robustness properties is presented for a multivariable aircraft control problem. The internal dynamics of the neurocontroller are synthesized by a state estimator feedback loop. The neurocontrol is generated by a multilayer feedforward neural network which is trained through backpropagation to minimize an objective function that is a weighted sum of tracking errors, and control input commands and rates. The neurocontroller exhibits good robustness through stability margins in phase and vehicle output gains. By maintaining performance and stability in the presence of sensor failures in the error loops, the structure of the neurocontroller is also consistent with the classical approach of flight control design.

Troudet, T.↗

NASA NTRS1992

Journey into tomorrow - Developing nuclear propulsion for the Space Exploration Initiative

Nuclear propulsion, either nuclear thermal propulsion or nuclear electric propulsion, offers the potential of reduced trip times and/or reduced mass into low earth orbit, compared to chemical propulsion systems. In addition, the greater performance benefits of nuclear propulsion can provide the added margin for greater operational flexibility, including mission abort options and increased launch windows. During the 1950s and 1960s experimental and analytical studies showed the feasibility of nuclear propulsion. NASA, in cooperation with other agencies and organizations, is currently planning a technology development program for nuclear propulsion. The overall objective is to develop at least one NTP concept and one NEP concept for piloted and robotic (e.g., cargo) missions to Mars.

Harer, Kathleen F.↗

NASA NTRS1992

Design and evaluation of a robust dynamic neurocontroller for a multivariable aircraft control problem

The design of a dynamic neurocontroller with good robustness properties is presented for a multivariable aircraft control problem. The internal dynamics of the neurocontroller are synthesized by a state estimator feedback loop. The neurocontrol is generated by a multilayer feedforward neural network which is trained through backpropagation to minimize an objective function that is a weighted sum of tracking errors, and control input commands and rates. The neurocontroller exhibits good robustness through stability margins in phase and vehicle output gains. By maintaining performance and stability in the presence of sensor failures in the error loops, the structure of the neurocontroller is also consistent with the classical approach of flight control design.

Troudet, T.↗

NASA NTRS1993

Hypersonic vehicle control law development using H(infinity) and micron-synthesis

Hypersonic vehicle control law development using H(infinity) and mu-synthesis is discussed. Airbreathing SSTO vehicles has a mutli-faceted mission that includes orbital operations, as well as re-entry and descent culminating in horizontal landing. However, the most challenging part of the operations is the ascent to orbit. The airbreathing propulsion requires lengthy atmospheric flight that may last as long as 30 minutes and take the vehicle half way around the globe. The vehicles's ascent is characterized by tight payload to orbit margins which translate into minimum fuel orbit as the performance criteria. Issues discussed include: SSTO airbreathing vehicle issues; control system performance requirements; robust control law framework; H(infinity) controller frequency analysis; and mu controller frequency analysis.

Gregory, Irene M.↗

NASA NTRS2001

Optimization of a GO2/GH2 Impinging Injector Element

An injector optimization methodology, method i, is used to investigate optimal design points for a gaseous oxygen/gaseous hydrogen (GO2/GH2) impinging injector element. The unlike impinging element, a fuel-oxidizer- fuel (F-O-F) triplet, is optimized in terms of design variables such as fuel pressure drop, (Delta)P(sub f), oxidizer pressure drop, (Delta)P(sub o), combustor length, L(sub comb), and impingement half-angle, alpha, for a given mixture ratio and chamber pressure. Dependent variables such as energy release efficiency, ERE, wall heat flux, Q(sub w), injector heat flux, Q(sub inj), relative combustor weight, W(sub rel), and relative injector cost, C(sub rel), are calculated and then correlated with the design variables. An empirical design methodology is used to generate these responses for 163 combinations of input variables. Method i is then used to generate response surfaces for each dependent variable. Desirability functions based on dependent variable constraints are created and used to facilitate development of composite response surfaces representing some, or all, of the five dependent variables in terms of the input variables. Three examples illustrating the utility and flexibility of method i are discussed in detail. First, joint response surfaces are constructed by sequentially adding dependent variables. Optimum designs are identified after addition of each variable and the effect each variable has on the design is shown. This stepwise demonstration also highlights the importance of including variables such as weight and cost early in the design process. Secondly, using the composite response surface which includes all five dependent variables, unequal weights are assigned to emphasize certain variables relative to others. Here, method i is used to enable objective trade studies on design issues such as component life and thrust to weight ratio. Finally, specific variable weights are further increased to illustrate the high marginal cost of realizing the last increment of injector performance and thruster weight.

Tucker, P. Kevin↗