Consistent Turbulent Boundary Layer Wall Pressure Spectra and Coherence Functions.
Abstract not provided.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Abstract not provided.
Advanced instruments for liquid chromatography enables the operation of columns packed with sub-2 {micro}m particles at the very high inlet pressures, up to 1000 bar, that are necessary to achieve the high column efficiency and the short analysis times that can be provided by the use of these columns. However, operating rather short columns at high mobile phase velocities, under high pressure gradients causes the production of a large amount of heat due to the viscous friction of the eluent percolating through the column bed. The evacuation of this heat causes the formation of significant axial and radial temperature gradients. Due to these thermal gradients, the retention factors of analytes and the mobile phase velocity are no longer constant throughout the column. The consequence of this heat production is a loss of column efficiency. We previously developed a model combining the heat and mass balance of the column, the equations of flow through porous media, and a linear isotherm model of the analyte. This model was solved and validated for conventional columns operated under moderate pressures. We report here on the results obtained when this model is applied to columns packed with very fine particles, operated under very high pressures. These results prove that our model accounts well for all the experimental results. The same column that elutes symmetrical, nearly Gaussian peaks at low flow rates, under relatively low pressure drops, provides strongly deformed, unsymmetrical peaks when operated at high flow rates, under high pressures, and under different thermal environments. The loss in column efficiency is particularly important when the column wall is kept at constant temperature, by immersing the column in a water bath.
Knock in spark-ignited (SI) engines is initiated by autoignition of the unburned gasses upstream of spark-ignited, propagating, turbulent premixed flames. Knock propensity of fuel/air mixtures is typically quantified using research octane number (RON), motor octane number (MON), or methane number (MN; for gaseous fuels), which are measured using single-cylinder, variable compression ratio engines. In this study, knock propensity of SI fuels was quantified via observations of end-gas autoignition (EGAI) in unburned gasses upstream of laser-ignited, premixed flames at elevated pressures and temperatures in a rapid compression machine. Stoichiometric primary reference fuel (PRF; n-heptane/isooctane) blends of varying reactivity (50 ≤ PRF ≤ 100) were ignited using an Nd:YAG laser over a range of temperatures and pressures, all in excess of 545 K and 16.1 bar. Laser ignition produced outwardly-propagating premixed flames. High-speed pressure measurements and schlieren images indicated the presence of EGAI. The fraction of the total heat release attributed to EGAI (i.e., EGAI fraction) varied with fuel reactivity (i.e., octane number) and the time-integrated temperature of the end-gas prior to ignition. Flame propagation rates, which were measured using schlieren images, were only weakly correlated with octane number but were affected by turbulence caused by variation in piston timing. Under conditions of low turbulence, measured flame propagation rates approached one-dimensional premixed laminar flame speed computations performed at the same conditions. Experiments were simulated with a three-dimensional CONVERGE™ model using reduced chemical kinetics (121 species, 538 reactions). The simulations accurately captured the measured flame propagation rates, as well as the variation in EGAI fraction with fuel reactivity and time-integrated end-gas temperature. The simulations also revealed low-temperature heat release as well as formaldehyde and hydrogen peroxide formation in the end-gas upstream of the propagating flame, which increased the temperature and degree of chain branching in the end-gas, ultimately leading to EGAI.
Radio-frequency (RF) carpets with ultra-fine pitches are examined for ion transport in gases at atmospheric pressures and above. We develop new analytic and computational methods for modeling RF ion transport at densities where dynamics are strongly influenced by buffer gas collisions. An analytic description of levitating and sweeping forces from phased arrays is obtained, then thermodynamic and kinetic principles are used to calculate ion loss rates in the presence of collisions. This methodology is validated against detailed microscopic SIMION simulations. We then explore a parameter space of special interest for neutrinoless double beta decay experiments: transport of barium ions in xenon at pressures from 1 to 10 bar. Our computations account for molecular ion formation and pressure dependent mobility as well as finite temperature effects. We discuss the challenges associated with achieving suitable operating conditions, which lie beyond the capabilities of existing devices, using presently available or near-future manufacturing techniques.
Explore the source record for details and available documents.
Ambient pressure CaV{sub 2}O{sub 4} and high-pressure NaV{sub 2}O{sub 4} crystallize in the CaFe{sub 2}O{sub 4} structure type containing double chains of edge-sharing VO{sub 6} octahedra. Recent measurements on NaV{sub 2}O{sub 4} reveal low-dimensional metallicity and evidence of half-metallic ferromagnetism. In contrast, CaV{sub 2}O{sub 4} is an antiferromagnetic insulator. To explore the evolution of these ground-state behaviors, we have prepared a series of Ca-doped NaV{sub 2}O{sub 4} compounds with the formula Na{sub 1-x}Ca{sub x}V{sub 2}O{sub 4} (x = 0-1) using high-pressure synthesis. Samples at the Na end (x = 0-0.07) show a broad antiferromagnetic transition in the 120-160 K range in accordance with earlier reports. Transport measurements show an insulator-metal transition at x {approx} 0.2. Samples with higher Ca concentrations (x = 0.4-0.7) exhibit a metal-insulator transition around 150 K. The results for the Na{sub 1-x}Ca{sub x}V{sub 2}O{sub 4} solid solution is discussed in comparison to existing studies at the Ca- and Na-rich ends.
Reduction and oxidation kinetics of a CuFeMnAlO 4+δ oxygen carrier for methane were studied using an atmospheric thermogravimetric analyzer (TGA) and a pressurized TGA. Important parameters such as temperature (500–900 °C), particle size distribution (150–650 μm), and partial pressures of reactants (methane and oxygen) were evaluated. Results showed that the reduction of the oxygen carrier was not affected by particle size distribution studied in this work, and that above 750 °C, the effect of the temperature on oxygen carrier reduction started to diminish. The reaction time approaches an asymptotic limit as methane partial pressure increases. For oxygen carrier oxidation, it was found that the rate of oxidation increased with increasing oxygen concentration. The effect of the oxygen concentration was more noticeable when the oxygen concentration was below 7.5%. Because of the inherent feature of the oxygen carrier, its chemical looping with oxygen uncoupling property was also assessed. A phase boundary-controlled shrinking sphere model was used to model the test data from the TGAs. Modeling results showed that the oxygen carrier reduction had a reaction order of 1 with an activation energy of ∼46 kJ/mol. Oxygen carrier oxidation demonstrated a reaction order of 1.1 with an activation energy of ∼55 kJ/mol. Additionally, the differences of the experimental results between the atmospheric pressure TGA and the pressurized TGA were discussed in detail and the limitations of the pressurized TGA were highlighted.
The effect of incorporation of Fe 2+ on the perovskite ( Pbnm ) and postperovskite ( Cmcm ) structures was investigated in the (Mg,Fe)GeO 3 system at high pressures and temperatures using laser-heated diamond anvil cell and synchrotron X-ray diffraction. Samples with compositions of Mg# ≥ 48 were shown to transform to the perovskite (~30 GPa and ~1500 K) and postperovskite (>55 GPa, ~1600-1800 K) structures. Compositions with Mg# ≥ 78 formed single-phase perovskite and postperovskite, whereas those with Mg# < 78 showed evidence for partial decomposition. The incorporation of Fe into the perovskite structure causes a decrease in octahedral distortion as well as a modest decrease in bulk modulus (K 0 ) and a modest increase in zero-pressure volume (V 0 ). It also leads to a decrease in the perovskite-to-postperovskite phase transition pressure by ~9.5 GPa over compositions from Mg#78 to Mg#100.
Pt catalyst particles on reducible oxide supports often change their activity significantly at elevated temperatures due to the strong metal–support interaction (SMSI), which induces the formation of an encapsulation layer around the noble metal particles. However, the impact of oxidizing and reducing treatments at elevated pressures on this encapsulation layer remains controversial, partly due to the “pressure gap” between surface science studies and applied catalysis. In the present work, we employ synchrotron-based near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) to study the effect of O 2 and H 2 on the SMSI-state of well-defined Pt/TiO 2 (110) catalysts at pressures of up to 0.1 Torr. Further, by tuning the O 2 pressure, we can either selectively oxidize the TiO 2 support or both the support and the Pt particles. Catalyzed by metallic Pt, the encapsulating oxide overlayer grows rapidly in 1 × 10 –5 Torr O 2 , but orders of magnitude less effectively at higher O 2 pressures, where Pt is in an oxidic state. While the oxidation/reduction of Pt particles is reversible, they remain embedded in the support once encapsulation has occurred.
Abstract not provided
Abstract not provided
Pressure-retarded osmosis (PRO) has the potential to generate sustainable energy from salinity gradients. PRO is typically considered for operation with river water and seawater, but a far greater energy of mixing can be harnessed from hypersaline solutions. This study investigates the power density that can be obtained in PRO from such concentrated solutions. Thin-film composite membranes with an embedded woven mesh were supported by tricot fabric feed spacers in a specially designed crossflow cell to maximize the operating pressure of the system, reaching a stable applied hydraulic pressure of 48 bar (700 psi) for more than 10 h. Operation at this increased hydraulic pressure allowed unprecedented power densities, up to 60 W/m(2) with a 3 M (180 g/L) NaCl draw solution. Experimental power densities demonstrate reasonable agreement with power densities modeled using measured membrane properties, indicating high-pressure operation does not drastically alter membrane performance. Our findings exhibit the promise of the generation of power from high-pressure PRO with concentrated solutions.
The corundum-type In{sub 2-2x}Zn{sub x}Sn{sub x}O{sub 3} solid solution (cor-ZITO, x {<=} 0.7) was synthesized at 1000 C under a high pressure of 70 kbar. cor-ZITO is a high-pressure polymorph of the transparent conducting oxide bixbyite-In{sub 2-2x}Zn{sub x}Sn{sub x}O{sub 3} (x {<=} 0.4). Analysis of the extended X-ray absorption fine structure suggests that significant face-sharing of Zn and Sn octahedra occurs, as expected for the corundum structure type. In contrast to the ideal corundum structure, however, Zn and Sn are displaced and form oxygen bonds with lengths that are similar to those observed in high-pressure ZnSnO{sub 3}. Powder X-ray diffraction patterns of cor-ZITO showed the expected unit cell contraction with increased cosubstitution, but no evidence for ilmenite-type ordering of the substituted Zn and Sn. A qualitative second harmonic generation measurement, for the solid solution x = 0.6 and using 1064 nm radiation, showed that Zn and Sn adopt a polar LiNbO{sub 3}-type arrangement.
Noncrystalline oxides under pressure undergo gradual structural modifications, highlighted by the formation of a dense noncrystalline network topology. The nature of the densified networks and their electronic structures at high pressures may account for the mechanical hardening and the anomalous changes in electromagnetic properties. Despite its importance, direct probing of the electronic structures in amorphous oxides under compression above the Mbar pressure (>100 GPa) is currently lacking. Here, we report the observation of pressure-driven changes in electronic configurations and their delocalization around oxygen in glasses using inelastic X-ray scattering spectroscopy (IXS). In particular, the first O K-edge IXS spectra for compressed GeO 2 glass up to 148 GPa, the highest pressure ever reached in an experimental study of GeO 2 glass, reveal that the glass densification results from a progressive increase of oxygen proximity. While the triply coordinated oxygen [3] O is dominant below ~50 GPa, the IXS spectra resolve multiple edge features that are unique to topologically disordered [4] O upon densification above 55 GPa. Topological compaction in GeO 2 glass above 100 GPa results in pronounced electronic delocalization, revealing the contribution from Ge d-orbitals to oxide densification. Strong correlations between the glass density and the electronic configurations beyond the Mbar conditions highlight the electronic origins of densification of heavy-metal-bearing oxide glasses. Furthermore, current experimental breakthroughs shed light on the direct probing of the electronic density of states in high-Z oxides above 1 Mbar, offering prospects for studies on the pressure-driven changes in magnetism, superconductivity, and electronic transport properties in heavy-metal-bearing oxides under compression.
Abstract not provided
Fluid flow through fractured rock systems is governed in large part by the distribution, interconnectivity, and size of fracture apertures. In-situ stress is one of the primary factors controlling fracture aperture, and one that is altered significantly during high-pressure fluid injections or extractions. Interactions between stress, pore pressure, aperture, and fluid flow can result in complex and evolving poroelastic behavior with significant implications regarding the predictability and risk of developing and managing deep subsurface reservoirs (geothermal, fossil energy, and geologic carbon sequestration). In saturated crystalline rocks, bulk electrical conductivity is highly sensitive to porosity, and therefore to fracture aperture size and distribution. We demonstrate the use of time-lapse 3D electrical resistivity tomography for remotely monitoring stress induced changes in aperture distribution during high pressure injections into a fractured rock system at a scale of tens of meters. Results reveal a complex and continuously evolving stress field involving aperture dilations in the natural fracture system and aperture contractions in adjacent zones of shadow stress. Results provide information about the spatiotemporal changes in the system behavior and point to the potential of electrical imaging for autonomously and remotely monitoring evolving stress conditions by proxy through changes in bulk electrical conductivity.