Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “POD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Effects of the air breathing propulsion system on space shuttle orbiter subsonic stability and control characteristics (OA71A)

Experimental aerodynamic investigations were conducted on an 0.0405 scale representation of the -89B (2A) Space Shuttle Orbiter in a 7.75 x 11.00 ft low speed wind tunnel during the time period from July 27, 1973 to August 3, 1973. The primary test objective was to investigate the aerodynamic effects of engine nacelle grouping and location on the orbiter ferry mission configuration. Five nacelles were tested, both individually mounted as well as mounted in a podded configuration, at the baseline position and moved 45.0 in. aft (full scale). Orbiter control effectiveness, both with and without nacelles, was recorded at elevon deflections of 0 deg, 5 deg, 10 deg, -10 deg and -20 deg and aileron deflections, about 0 deg elevon, of 0 deg, 5 deg, 10 deg, and 15 deg. The model was sting mounted on a 2.5 inch diameter internal strain gage balance entering through the base region. The nominal angle of attack range was -4 deg or = alpha or = 30 deg. Yaw polars were recorded over the beta range of -10 deg or = beta or = at fixed angles of attack of 0 deg and 10 deg.

Mennell, R. C.↗
NASA NTRS1973

Effects of reaction control system jet simulation on the stability and control characteristics of a 0.015-scale space shuttle orbiter model in the Ames Research Center 3.5-foot hypersonic wind tunnel

An experimental investigation was performed in the Ames Research Center 3.5-Foot Hypersonic Wind Tunnel to obtain detailed effects which interactions between the RCS jet flow field and the local orbiter flow field have on orbiter hypersonic stability and control characteristics. Six-component force data were obtained through an angle-of-attack range of 15 to 35 deg with 0 deg angle of sideslip. The test was conducted with yaw, pitch and roll jet simulation at a free-stream Mach number of 10.3. These data simulate two SSV reentry flight conditions at Mach numbers of 28.3 and 10.3. Fuselage base pressures and pressures on the nonmetric RCS pods were obtained in addition to the basic force measurements. Model 42-0 was used for these tests.

Dziubala, T. J.↗
NASA NTRS1973

Static stability and control effectiveness of models 12-0 and 34-0 of the vehicle 3 configuration, volume 2

Static stability and control effectiveness characteristics of two 0.004 scale models of the vehicle 3 configuration are presented. The components investigated consisted of a single aft body, vertical/rudder, OMS pods with two interchangeable wings, four interchangeable forward bodies, four trimmers, and a spoiler. The test was conducted in a 14 x 14 inch trisonic wind tunnel over a Mach number range from 0.6 to 4.96. Angles of attack from 0 to 60 degrees and angles of sideslip from -10 to 10 degrees at 0, 10, 20, 30, and 40 degrees angle of attack were tested. Elevon, body flap, and speed brake deflection composed the parametric considerations. No grit was placed on the models during the test. The lateral-directional characteristics are presented along with some additional longitudinal data.

Allen, E. C.↗
NASA NTRS1973

Results of tests OA12 and IA9 in the Ames Research Center unitary plan wind tunnels on an 0.030-scale model of the Space Shuttle Vehicle 2A to determine aerodynamic loads, volume 11

Tests were conducted in wind tunnels during April and May 1973, on an 0.030-scale replica of the Space Shuttle Vehicle Configuration 2A. Aerodynamic loads data were obtained at Mach numbers from 0.6 to 3.5. The investigation included tests on the integrated (launch) configuration and on the isolated orbiter (entry configuration). The integrated vehicle was tested at angles of attack from -15 degrees to +40 degrees and angles of sideslip from -10 degrees to +10 degrees as dictated by trajectory considerations. The effects of orbiter/external tank incidence angle and deflected control surfaces on aerodynamic loads were also investigated. Tabulated pressure data are presented for: orbiter fuselage and base, upper MPS nozzle, OMS nozzle, body flap, OMS pod outside, and lower wing surface.

Spangler, R. H.↗
NASA NTRS1973

Effect of reaction control system jet-flow field interactions on a 0.015 scale model space shuttle orbiter aerodynamic characteristics

The effects of the reaction control system (RCS) jet-flow field interactions on the space shuttle orbiter system during entry are discussed. The primary objective of the test program was to obtain data for the shuttle orbiter configuration to determine control amplification factors resulting from jet interaction between the RCS plumes and the external flow over the vehicle. A secondary objective was to provide data for comparison and improvement of analytic jet interaction prediction techniques. The test program was divided into two phases; (1) force and moment measurements were made with and without RCS blowing, investigating environment parameters (R sub e, Alpha, Beta), RCS plume parameters (Jet pressure ratio, momentum ratio and thrust level), and geometry parameters (RCS pod locations) on the orbiter model, (2) oil flow visualization tests were conducted on a dummy balance at the end of the test.

Monta, W. J.↗
NASA NTRS1974

Results of tests OA12 and IA9 in the Ames Research Center unitary plan wind tunnels on an 0.030-scale model of the space shuttle vehicle 2A to determine aerodynamic loads, volume 13

Tests were conducted in wind tunnels during April and May 1973, on a 0.030-scale replica of the Space Shuttle Vehicle Configuration 2A. Aerodynamic loads data were obtained at Mach numbers from 0.6 to 3.5. The investigation included tests on the integrated (launch) configuration and on the isolated orbiter (entry configuration). The integrated vehicle was tested at angles of attack and sideslip from -8 deg to +8 deg. The isolated orbiter was tested at angles of attack from -15 deg to +40 deg and angles of sideslip from -10 deg to +10 deg as dictated by trajectory considerations. The effects of orbiter/external tank incidence angle and deflected control surfaces on aerodynamic loads were also investigated. Tabulated pressure data are given for the following components: orbiter fuselage and base; OMS and upper MPS nozzles; body flap; and OMS pod outside.

Spangler, R. H.↗
NASA NTRS1974

Effects of reaction control system jet simulation on the stability and control characteristics of a 0.015 scale space shuttle orbiter model tested in the Langley Research Center unitary plan wind tunnel

An experimental investigation was performed in the Langley Research Center Unitary Plan Wind Tunnel (Test 0A70) to obtain the detailed effects that RCS jet flow interactions with local orbiter flow field have on supersonic stability and control characteristics of the space shuttle orbiter. Six-component force data were obtained through an angle-of-attack range from 15 to 35 degrees at angles of sideslip of 0, +5, and -5 degrees. The test was conducted with yaw jet simulation at free-stream Mach numbers of 2.5 and 4.6, simulating SSV re-entry flight conditions at these Mach numbers. In addition to the basic force measurements, fuselage base pressures and pressures on the non-metric RCS pods were obtained.

Daileda, J. J.↗
NASA NTRS1974

Results of tests OA26 and IA16 in the NASA/ARC 3.5-foot hypersonic wind tunnel on an 0.015-scale model (36-OTS) of the space shuttle configuration 140A/B to obtain pressures for venting analysis

Tests were conducted, from November 15 to December 4, 1973, to obtain surface pressure data on an 0.015-scale replica of the Space Shuttle Vehicle 4. Data were obtained at Mach numbers of 5.3, 7.4, and 10.3, to support the venting analysis for both launch and entry conditions. These tests were the final tests in a series covering a Mach number range from 0.6 to 10.3. The model was instrumented with pressure orifices in the vicinity of the cargo bay door hinge and parting lines, and on the side of the fuselage at the crew compartment, and below the orbital maneuvering system pods at the aft compartment. The model was tested at angles of attack and sideslip consistent with expected divergencies from the nominal trajectory.

Spangler, R. H.↗
NASA NTRS1974

Results of tests OA63 and IA29 on an 0.015 scale model of the space shuttle configuration 140 A/B in the NASA/ARC 6- by 6-foot transonic wind tunnel, volume 1

Tests were conducted in the NASA/ARC 6- by 6-foot transonic wind tunnel from September 12 to September 28, 1973 on an 0.015-scale model of the space shuttle configuration 140 A/B. Surface pressure data were obtained for the orbiter for both launch and entry configuration at Mach numbers from 0.6 to 2.0. The surface pressures were obtained in the vicinity of the cargo bay door hinge and parting lines, the side of the fuselage at the crew compartment and below the OMS pods at the aft compartment. Data were obtained at angles of attack and sideslip consistent with the expected divergencies along the nominal trajectory. These tests were first in a series of tests supporting the orbiter venting analysis. The series will include tests in three facilities covering a total Mach number range from 0.6 to 10.4.

Spangler, R. H.↗
NASA NTRS1974

Results of tests (OA64 and IA35) of an 0.015-scale model (36-OTS) of the space shuttle configuration 140A/B in the NASA/LaRC unitary plan wind tunnel

Supersonic aerodynamic tests were conducted in the NASA/LaRC Unitary Plan Wind Tunnel on a 0.015-scale model of the Space Shuttle Vehicle 4 configuration. Surface pressure data were obtained for both the launch (test IA35) and entry (test OA64) configurations at Mach numbers from 2.5 to 4.5. The surface pressure was measured in the vicinity of the cargo bay door hinge and parting lines and on the side of the fuselage at the crew compartment and below the OMS pods at the aft compartment. Data were obtained for angles of attack and sideslip consistent with the expected excursions about the nominal trajectory values at the test Mach numbers. These tests were a part of a test series supporting the orbiter venting analysis over a Mach number range from 0.6 to 10.4

Thornton, D. E.↗
NASA NTRS1973

Techniques development for whale migration tracking

Effort leading to the completion of development and fabrication of expansible whale harnesses and whale-carried instrument pods is described, along with details of the gear. Early preparative effort for a January-February 1974 field expedition is reported.

Goodman, R. M.↗
NASA NTRS1974

Investigation of space shuttle orbiter subsonic stability and control characteristics in the NAAL low speed wind tunnel (OA62B), volume 2

Experimental aerodynamic investigations were conducted on a sting-mounted 0.0405 scale representation of the 140A/B space shuttle orbiter in a 7.75 ft by 11 ft low speed wind tunnel during the period from November 14, 1973 to December 6, 1973. Establishment of basic longitudinal stability characteristics in and out of ground effect, and the establishment of lateral-directional stability characteristics in free air were the primary test objectives. The following effects and configurations were tested: (1) two dual podded nacelle configurations; (2) stability and control characteristics at nominal elevon deflections, rudder deflections, airleron deflections, rudder flare angles, and body flap deflections; (3) effects of various elevon and elevon/fuselage gaps on longitudinal stability and control; (4) pressures on the vertical tail at spanwise stations using pressure bugs; (5) aerodynamic force and moment data measured in the stability axis system by an internally mounted, six-component strain gage balance. For Vol. 1, see N74-32324.

Mennell, R.↗
NASA NTRS1974

Orbital maneuvering subsystem functional path analysis for performance monitoring fault detection and annunciation

The functional paths of the Orbital Maneuver Subsystem (OMS) is defined. The operational flight instrumentation required for performance monitoring, fault detection, and annunciation is described. The OMS is a pressure fed rocket engine propulsion subsystem. One complete OMS shares each of the two auxiliary propulsion subsystem pods with a reaction control subsystem. Each OMS is composed of a pressurization system, a propellant tanking system, and a gimbaled rocket engine. The design, development, and operation of the system are explained. Diagrams of the system are provided.

Keesler, E. L.↗
NASA NTRS1973

Effect of rotor design tip speed on noise of a 1.21 pressure ratio model fan under static conditions

Preliminary results are presented for a reverberant-field noise investigation of three fan stages designed for the same overall total pressure ratio of 1.21 at different rotor tip speeds (750, 900, and 1050 fps). The stages were tested statically in a 15-in.-dia model lift fan installed in a wing pod located in the test section of a wind tunnel. Although the fan stages produced essentially the same design pressure ratio, marked differences were observed in the variation of fan noise with fan operating speed. At design speed, the forward-radiated sound power level was approximately the same for the 750 and 900 fps stages. For the 1050 fps stage, the design-speed forward-radiated power level was about 7 dB higher due to the generation of multiple pure tone noise.

Loeffler, I. J.↗
NASA NTRS1974

Results of investigations on an 0.015-scale 140A/B configuration of the Rockwell International space shuttle orbiter (model 49-O) in the NASA/Ames Research Center 3.5-foot hypersonic wind tunnel (OA36)

The results of wind tunnel tests of the 140A/B configuration components are reported for the fuselage, canopy, elevons, bodyflaps, pods, engine nozzles, rudder, vertical tail, and wing. The test facility, and data reduction procedures are described. Test results for each component are graphed, and tabulated source data are included.

Milam, M. D.↗
NASA NTRS1974

Influence of configuration details on the subsonic characteristics of a space shuttle orbiter design

An investigation was conducted in the Langley low-turbulence pressure tunnel of a model of a space shuttle orbiter design in order to determine the influence of minor configuration geometric details on the aerodynamic characteristics at subsonic speeds. A plane wing was tested with a small planform fillet; a twisted wing was tested with both a small and a large planform fillet. Tailored attitude-control propulsion-system wing-tip and body pods, trisegmented elevons, and canopy effects were also investigated. The tests were conducted at angles of attack from -3 deg to 24 deg for sideslip angles of 0 deg and 6 deg and at a Mach number of 0.25.

Decker, J. P.↗
NASA NTRS1974

Results of differential elevon/aileron deflection for lateral control optimization and elevon hinge moment investigations on an 0.015-scale model (49-0) of the space shuttle orbiter in the NASA/Langley Research Center 8 foot TPT (OA116)

Aerodynamic investigations were conducted in a transonic pressure tunnel on an 0.015 scale model of the space shuttle orbiter. Major test objectives were to determine: (1) transonic differential elevon/aileron lateral control optimization; (2) transonic elevon hinge moments; (3) transonic effects of the baseline 6 inch elevon/elevon and elevon/fuselage gaps; and (4) transonic effects of the short OMS pods. Six-component aerodynamic force and moment, and elevon hinge moment data, were recorded over an angle-of-attack range form -2 to +22 degrees.

Lindsey, A. I.↗