Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLATES - PRESSURE RECTANGULAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Dual Active Surface Heat Flux Gage Probe

A unique plug-type heat flux gage probe was tested in the NASA Ames Research Center 2x9 turbulent flow duct facility. The probe was fabricated by welding a miniature dual active surface heat flux gage body to the end of a hollow metal cylindrical bolt containing a metal inner tube. Cooling air flows through the inner tube, impinges onto the back of the gage body and then flows out through the annulus formed between the inner tube and the hollow bolt wall. Heat flux was generated in the duct facility with a Huels arc heater. The duct had a rectangular cross section and one wall was fabricated from 2.54 centimeter thick thermal insulation rigid surface material mounted onto an aluminum plate. To measure heat flux, the probe was inserted through the plate and insulating materials with the from of the gage located flush with the hot gas-side insulation surface. Absorbed heat fluxes measured with the probe were compared with absorbed heat fluxes measured with six water-cooled reference calorimeters. These calorimeters were located in a water-cooled metal duct wall which was located across from the probe position. Correspondence of transient and steady heat fluxes measured with the reference calorimeters and heat flux gage probe was generally within a satisfactory plus or minus 10 percent. This good correspondence was achieved even though the much cooler probe caused a large surface temperature disruption of 1000K between the metal gage and the insulation. However, this temperature disruption did not seriously effect the accuracy of the heat flux measurement. A current application for dual active surface heat flux gages is for transient and steady absorbed heat flux, surface temperature and heat transfer coefficient measurements on the surface of an oxidizer turbine inlet deflector operating in a space shuttle test bed engine.

Liebert, Curt H.↗
NASA NTRS1972

The effect of gravity induced free convection upon the melting phenomena of a finite paraffin slab for thermal control

Two theoretical models were developed to predict the thermal response of the phase change material to a given hot plate temperature. A two-dimensional pure conduction model was developed to predict the melting of the phase change material when heat transfer was a function of conduction. A combined conduction-convection model, also two-dimensional, was developed to predict the phase change phenomena when heat transfer was a function of conduction and gravity-induced free convection. Both models were solved using explicit finite difference approximations on a digital computer. The experimental equipment consisted of a rectangular cell utilizing a heat chamber, an expansion chamber, and a test chamber; a sixteen channel multipoint recorder, and a fluid flow system. The recorder monitered hot and cold plate temperatures and interior node temperatures at two second intervals. A comparison of theoretical temperature profiles and experimental temperature profiles is presented for six runs at various angles of inclination of the test cell with respect to the horizontal direction. A detailed discussion of results is presented.

Bain, R. L.↗
NASA NTRS1993

Isolated and coupled superquadric loop antennas for mobile communications applications

This work provides an investigation of the performance of loop antennas for use in mobile communications applications. The analysis tools developed allow for high flexibility by representing the loop antenna as a superquadric curve, which includes the case of circular, elliptical, and rectangular loops. The antenna may be in an isolated environment, located above an infinite ground plane, or placed near a finite conducting plate or box. In cases where coupled loops are used, the two loops may have arbitrary relative positions and orientations. Several design examples are included to illustrate the versatility of the analysis capabilities. The performance of coupled loops arranged in a diversity scheme is also evaluated, and it is found that high diversity gain can be achieved even when the antennas are closely spaced.

Jensen, Michael A.↗
NASA NTRSDate not supplied

Laminar to Turbulence Transition in Boundary Layers due to Tripping Devices

Direct numerical simulations (DNS)and linear stability analyses were performed to identify the mechanisms by whichtwo-and three-dimensional trips promote early transition in subsonic boundary layers over a flat plate. Investigations were conducted for threeboundary-layer transition trip configurations:a two-dimensional smooth hump,a two-dimensional rectangular-shapedrod and a three-dimensional zig-zagtape. The smooth hump was used by Park et al.1in the linear and nonlinear parabolized stability (PSE) computations. Reynolds numbersbased on the tripheights are 710, 683,and 300 for the two-and three-dimensional trips, respectively. Simulations withthe smooth hump showed that the flow becomes stable upstream and strongly unstable downstream of the hump. Simulations with the two-dimensional rectangular trip showed that the flow separates at the top of the trip and forms a long recirculation zonedownstream. However, the flow remains steady in the simulation without any external disturbances. Linear stability analysis showed that the inflectional profile in the recirculation zone is strongly unstable to frequencies in the range of 100-300 Hz. Simulations with the external disturbances forced at the frequency of 200 Hz showed that disturbances grow strongly inside the recirculation zone as observed in the Klebanoff2 experiment. Three-dimensional simulations with secondary disturbances of fundamental, subharmonic, and oblique types produced turbulent flows shortlydownstream. The three-dimensional zig-zag trip with a small roughness Reynolds number lead to early breakdown to a turbulent flow.

Stability↗
NASA NTRS1976

Stability of a viscous fluid in a rectangular cavity in the presence of a magnetic field

The stability of an electrically conducting fluid subjected to two dimensional disturbance was investigated. A physical system consisting of two parallel infinite vertical plates which are thermally insulated was studied. An external magnetic field of constant strength was applied to normal plates. The fluid was heated from below so that a steady temperature gradient was maintained in the fluid. The governing equations were derived by perturbation technique, and solutions were obtained by a modified Galerkin method. It was found that the presence of the magnetic field increases the stability of the physical system and instability can occur in the form of neutral or oscillatory instability.

Liang, C. Y.↗
NASA NTRS1983

Residual strength assessment of low velocity impact damage of graphite-epoxy laminates

This report contains the study of Low Velocity Transverse Impact Damage of graphite-epoxy T300/5208 composite laminates. The specimen, 100 mm diameter clamped plates, were impact damaged by a cantilever-type instrumented 1-inch diameter steel ball. Study was limited to impact velocity 6 m/sec. Rectangular strips, 50 mm x 125 mm, were cut from the impact-damage specimens so that the impact damage zone was in the center of the strips. These strips were tested in tension to obtain their residual strength. An energy dissipation model was developed to predict the residual strength from fracture mechanics concepts. Net energy absorbed I(a) was evaluated from coefficient of restitution concepts based on shear dominated theory of fiber-reinforced materials, with the modification that during loading and unloading the shear deformation are respectively elastic-plastic and elastic. Delamination energy I(d) was predicted by assuming that the stiffness of the laminate dropped due to debonding. Fiber-breakage energy, assumed to be equal to the difference of I(a) and I(d), was used to determine the residual strength. Predictions were compared with test results.

Lal, K. M.↗
NASA NTRS1960

Application of Variational Methods to the Thermal Entrance Region of Ducts

A variational method is presented for solving eigenvalue problems which arise in connection with the analysis of convective heat transfer in the thermal entrance region of ducts. Consideration is given, to both situations where the temperature profile depends upon one cross-sectional coordinate (e.g. circular tube) or upon two cross-sectional coordinates (e.g. rectangular duct). The variational method is illustrated and verified by application to laminar heat transfer in a circular tube and a parallel-plate channel, and good agreement with existing numerical solutions is attained. Then, application is made to laminar heat transfer in a square duct as a check, an alternate computation for the square duct is made using a method indicated by Misaps and Pohihausen. The variational method can, in principle, also be applied to problems in turbulent heat transfer.

Sparrow, E. M.↗
NASA NTRS1986

Evaluation of residual strength of composite laminates damaged by low velocity impacts

This work presents the study of Low Velocity Transverse Impact damage of graphite-epoxy T300/5208 composite material. An energy dissipation model was developed to predict the residual strength from fracture mechanics concepts. The specimens, 100 mm diameter clamped plates, were impact damaged by a cantilever-type instrumented 1-inch diameter steel ball. This study was limited to impact velocity 6 m/sec. Rectangular strips, 50 mm x 125 mm, were cut from the impact-damaged specimens so that the impact damage zone was in the center of the strips. These strips were tested to obtain their residual strength. Predictions were compared with the test results.

Lal, K. M.↗
NASA NTRS1972

A fracture mechanics analysis of adhesive failure in a single lap shear joint.

Discussion of adhesive fracture of single lap shear joints in terms of a maximum stress criterion and an energy balance. The Goland and Reissner (1944) analysis is used to determine the stress distribution in the adhesive assembly, and the results obtained are introduced into an energy balance to determine the initiation of adhesive fracture. In the stress analysis the loads at the edges of the joint are first determined. This is a problem in which the deformation of the joint sheets must be taken into account and is solved by using the finite-deflection theory of cylindrically bent plates. Then the stress in the joint due to applied loads is determined. This problem is formulated as one in plane strain consisting of two rectangular sheets of equal thickness and unit width. With the aid of this stress analysis and the stresses obtained from the conditions of equilibrium the contributions to the energy change with crack length are calculated. The analysis performed is then compared with a maximum stress criterion for a lap joint.

Devries, K. L.↗
NASA NTRS1986

An experiment for determining the Euler load by direct computation

A direct algorithm is presented for computing the Euler load of a column from experimental data. The method is based on exact inextensional theory for imperfect columns, which predicts two distinct deflected shapes at loads near the Euler load. The bending stiffness of the column appears in the expression for the Euler load along with the column length, therefore the experimental data allows a direct computation of bending stiffness. Experiments on graphite-epoxy columns of rectangular cross-section are reported in the paper. The bending stiffness of each composite column computed from experiment is compared with predictions from laminated plate theory.

Thurston, Gaylen A.↗
NASA NTRS1985

Dislocation model for aseismic fault slip in the transverse ranges of Southern California

Geodetic data at a plate boundary can reveal the pattern of subsurface displacements that accompany plate motion. These displacements are modelled as the sum of rigid block motion and the elastic effects of frictional interaction between blocks. The frictional interactions are represented by uniform dislocation on each of several rectangular fault patches. The block velocities and fault parameters are then estimated from geodetic data. Bayesian inversion procedure employs prior estimates based on geological and seismological data. The method is applied to the Transverse Ranges, using prior geological and seismological data and geodetic data from the USGS trilateration networks. Geodetic data imply a displacement rate of about 20 mm/yr across the San Andreas Fault, while the geologic estimates exceed 30 mm/yr. The prior model and the final estimates both imply about 10 mm/yr crustal shortening normal to the trend of the San Andreas Fault. Aseismic fault motion is a major contributor to plate motion. The geodetic data can help to identify faults that are suffering rapid stress accumulation; in the Transverse Ranges those faults are the San Andreas and the Santa Susana.

Cheng, A.↗
NASA NTRS1987

Near-wall turbulence alteration through thin streamwise riblets

The possibility of improving the level of drag reduction associated with near-wall riblets is considered. The methodology involves the use of a hot-wire anemometer to study various surface geometries on small, easily constructed models. These models consist of small, adjacent rectangular channels on the wall aligned in the streamwise direction. The VITA technique is modified and applied to thin-element-array and smooth flat-plate data and the results are indicated schematically.

Wilkinson, Stephen P.↗
NASA NTRS1988

Effect of large amplitude pitching motions on the unsteady aerodynamic characteristics of flat-plate wings

Large-amplitude unsteady motion effects on the aerodynamic force and stability characteristics of flat-plate wings were investigated in a wind tunnel for the cases of two delta wings with respective leading edge sweeps of 70 and 45 deg, and a rectangular wing whose aspect ratio was equal to that of the 70-deg delta wing. Attention was given to the effects of reduced frequency and mean angle of attack. It is found that lags in vortex burst location and separation/reattachment of flow on the upper surface of the wing produced large overshoots and hysteresis loops in normal force and pitching moment coefficients that were a strong function of mean oscillation angle and reduced frequency.

Brandon, Jay M.↗
NASA NTRS2015

Jet Surface Interaction Scrubbing Noise from High Aspect-Ratio Rectangular Jets

Concepts envisioned for the future of civil air transport consist of unconventional propulsion systems in the close proximity of the airframe. Distributed propulsion system with exhaust configurations that resemble a high aspect ratio rectangular jet are among geometries of interest. Nearby solid surfaces could provide noise shielding for the purpose of reduced community noise. Interaction of high-speed jet exhaust with structure could also generate new sources of sound as a result of flow scrubbing past the structure, and or scattered noise from sharp edges. The present study provides a theoretical framework to predict the scrubbing noise component from a high aspect ratio rectangular exhaust in proximity of a solid surface. The analysis uses the Greens function (GF) to the variable density Pridmore-Brown equation in a transversely sheared mean flow. Sources of sound are defined as the auto-covariance function of second-rank velocity fluctuations in the jet plume, and are modeled using a RANS-based acoustic analogy approach. Acoustic predictions are presented in an 8:1 aspect ratio rectangular exhaust at three subsonic Mach numbers. The effect of nearby surface on the scrubbing noise component is shown on both reflected and shielded sides of the plate.

Propulsion Noise↗
NASA NTRS1987

Aseismic crustal deformation in the Transverse Ranges of southern California

Using geodetic data at a plate boundary, the subsurface displacements that accompany plate motion were modeled as the sum of rigid block motion and the elastic effects of frictional drag between blocks in a model consisting of 12 blocks and 27 rectangular fault patches. The block motion inferred from the geodetic data has the same order of magnitude as the geologic estimates, and for many faults the agreement was excellent. The model implies about 20 mm/y of crustal shortening normal to the trend of the San Andreas fault.

Cheng, Abe↗
NASA NTRS2002

Influence of Cooling Channel Geometry on the Thermal Response in Silicon Nitride Plates Studied

Engine manufacturers are continually attempting to improve the performance and efficiency of internal combustion engines. Usually they raise the operating temperature or reduce the cooling air requirement for the hot section turbine components. However, the success of these attempts depends on finding materials that are lightweight, are strong, and can withstand high temperatures. Ceramics are among the top candidate materials considered for such harsh applications. They hold low-density, high-temperature strength, and thermal conductivity, and they are undergoing investigation as potential materials for replacing nickel-base alloys and superalloys that are currently used for engine hot-section components. Ceramic structures can withstand higher operating temperatures and a harsh combustion environment. In addition, their low densities relative to metals help reduce component mass. The long-term objectives of the High Temperature Propulsion Components (HOTPC) Project are to develop manufacturing technology, thermal and environmental barrier coatings (TBC/EBC), and the analytical modeling capability to predict thermomechanical stresses in minimally cooled silicon nitride turbine nozzle vanes under simulated engine conditions. Two- and three-dimensional finite element analyses with TBC were conducted at the NASA Glenn Research Center. Nondestructive evaluation was used to determine processing defects. The study included conducting preliminary parametric analytical runs of heat transfer and stress analyses under steady-state conditions to demonstrate the feasibility of using cooled Si3N4 parts for turbine applications. The influence of cooling-channel shapes (such as circular, square, and ascending-order cooling channels) on cooling efficiency and thermal stresses was investigated. Temperature distributions were generated for all cases considered under both cooling and no-cooling conditions, with air being the cooling medium. The table shows the magnitude of the maximum and minimum temperature obtained for the plates under air cooling. Each channel's cross-sectional shape delivered a different temperature; however, the two-dimensional analyses for circular and square or equal-side rectangular holes produced close results. Moreover, the model of the panel with ascending order cooling channels experienced the lowest temperature. A difference of near 260 C was found among the three cooling-hole configurations investigated. The ascending-order cooling channels arrangement showed superior performance by attaining the lowest temperature (1077 C) in comparison to the circular (1379 C) and square (1343 C) channels for the same cooling-hole size. This indicates that the panel with ascending-order cooling channels is the most suitable configuration regardless of the complexity involved in its manufacture. More details pertaining to this study are reported.

Abdul-Aziz, Ali↗