Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Oxidation Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Feasibility of Ultraviolet Light Emitting Diodes as an Alternative Light Source for Photocatalysis

The objective of this study was to determine whether ultraviolet light emitting diodes (UV-LEDs) could serve as an alternative photon source efficiently for heterogeneous photocatalytic oxidation (PCO). An LED module consisting of 12 high-power UV-A LEDs was designed to be interchangeable with a UV-A fluorescent black light blue (BLB) lamp in a Silica-Titania Composite (STC) packed bed annular reactor. Lighting and thermal properties were characterized to assess the uniformity and total irradiant output. A forward current of (I(sub F)) 100 mA delivered an average irradiance of 4.0 m W cm(exp -2), which is equivalent to the maximum output of the BLB, but the irradiance of the LED module was less uniform than that of the BLB. The LED- and BLB-reactors were tested for the oxidization of 50 ppmv ethanol in a continuous flow-through mode with 0.94 sec space time. At the same irradiance, the UV-A LED reactor resulted in a lower PCO rate constant than the UV-A BLB reactor (19.8 vs. 28.6 nM CO2 sec-I), and consequently lower ethanol removal (80% vs. 91%) and mineralization efficiency (28% vs. 44%). Ethanol mineralization increased in direct proportion to the irradiance at the catalyst surface. This result suggests that reduced ethanol mineralization in the LED- reactor could be traced to uneven irradiance over the photocatalyst, leaving a portion of the catalyst was under-irradiated. The potential of UV-A LEDs may be fully realized by optimizing the light distribution over the catalyst and utilizing their instantaneous "on" and "off' feature for periodic irradiation. Nevertheless, the current UV-A LED module had the same wall plug efficiency (WPE) of 13% as that of the UV-A BLB. These results demonstrated that UV-A LEDs are a viable photon source both in terms of WPE and PCO efficiency.

Levine, Langanf H.↗
DOE OSTI2021

Physiological, genomic, and sulfur isotopic characterization of methanol metabolism by Desulfovibrio carbinolicus

Methanol is often considered as a non-competitive substrate for methanogenic archaea, but an increasing number of sulfate-reducing microorganisms (SRMs) have been reported to be capable of respiring with methanol as an electron donor. A better understanding of the fate of methanol in natural or artificial anaerobic systems thus requires knowledge of the methanol dissimilation by SRMs. In this study, we describe the growth kinetics and sulfur isotope effects of Desulfovibrio carbinolicus, a methanol-oxidizing sulfate-reducing deltaproteobacterium, together with its genome sequence and annotation. D. carbinolicus can grow with a series of alcohols from methanol to butanol. Compared to longer-chain alcohols, however, specific growth and respiration rates decrease by several fold with methanol as an electron donor. Larger sulfur isotope fractionation accompanies slowed growth kinetics, indicating low chemical potential at terminal reductive steps of respiration. In a medium containing both ethanol and methanol, D. carbinolicus does not consume methanol even after the cessation of growth on ethanol. Among the two known methanol dissimilatory systems, the genome of D. carbinolicus contains the genes coding for alcohol dehydrogenase but lacks enzymes analogous to methanol methyltransferase. We analyzed the genomes of 52 additional species of sulfate-reducing bacteria that have been tested for methanol oxidation. There is no apparent relationship between phylogeny and methanol metabolizing capacity, but most gram-negative methanol oxidizers grow poorly, and none carry homologs for methyltransferase (mtaB). Although the amount of available data is limited, it is notable that more than half of the known gram-positive methanol oxidizers have both enzymatic systems, showing enhanced growth relative to the SRMs containing only alcohol dehydrogenase genes. Thus, physiological, genomic, and sulfur isotopic results suggest that D. carbinolicus and close relatives have the ability to metabolize methanol but likely play a limited role in methanol degradation in most natural environments.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Gear Test Assembly – Report Experimental Testing and Gear Analysis (FY2021 Midyear Report)

The Gear Test Assembly (GTA) has completed three experimental campaigns at the Mechanisms Engineering Test Loop (METL) facility. The most recent campaign tested Inconel 718 spur gears, tapered roller bearings of 52100 bearing steel with no heat treatment, and a lantern ring shaft seal with spring-loaded fasteners. Testing was performed in Test Vessel 1 (TV1) with 250°C sodium that had an oxide concentration of <10ppm. Testing began in February 2021 and was ended in March 2021 when a thrust bearing assembly failed, requiring shutdown and maintenance. The third experimental campaign completed 1,568 simulated fuel assembly maneuvers before the thrust bearing failure. The GTA was removed from TV1 and cleaned in the Carbonation System. The GTA is currently being prepared for the next experimental campaign. Nondestructive examination methods have been developed at Argonne to monitor the health of the GTA spur gears. Eddy current testing (ECT) and ultrasonic testing (UT) were performed prior to sodium testing and after each experimental campaign. The NDE has shown that the primary damage mechanism is mechanical wear on the gear tooth surface. Several larger nicks are observable on the gear faces, with additional large nicks present on the edges of the gear teeth. While this damage is observable, the overall health of the gears is adequate for more in-sodium testing. A total of 12,752 simulated fuel assembly maneuvers have been completed using this set of gears.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1980

Energy efficient engine

The feasibility of meeting or closely approaching the emissions goals established for the Energy Efficient Engine (E3) Project with an advanced design, single annular combustor was determined. A total of nine sector combustor configurations and one full-annular-combustor configuration were evaluated. Acceptable levels of carbon monoxide and hydrocarbon emissions were obtained with several of the sector combustor configurations tested, and several of the configurations tested demonstrated reduced levels of nitrogen oxides compared to conventional, single annular designs. None of the configurations tested demonstrated nitrogen oxide emission levels that meet the goal of the E3 Project.

Burrus, D.↗
NASA NTRS1973

Oxidation resistant carbon-carbon composite for Space Shuttle application.

An oxidation resistant carbon-carbon composite has been developed for use on the NASA Space Shuttle Orbiter Vehicle which can function on the high temperature surfaces to satisfy the 100 mission reuse capability requirement. This paper describes the design requirements, materials and processes developed, and the successful testing of simulated full-scale prototype hardware. Materials considerations are illustrated, including strength and oxidation testing, along with physical property determinations, characterizing the material over the predicted temperature range of use.

Rogers, D. C.↗
NASA NTRS1990

Failure Morphologies of Cyclically Oxidized ZrO2-Based Thermal Barrier Coatings

Plasma-sprayed thermal barrier coatings (TBC s) were thermal cycle tested in air at 1163 C until spallation of the top coat. Each thermal cycle consisted of a 45 minute exposure at the elevated temperature followed by a 15 minute cool to ambient temperature. The TBC s consisted of a ZrO2-based top coat containing various amounts of Y2O3, and/or Yb2O3, Gd2O3, and Nd2O3 applied by air plasma spraying and an MCrAlY bond coat applied by low pressure plasma spraying. The substrate was a single-crystal, Ni-based superalloy. The time to failure of the top coat varied from tens to hundreds of thermal cycles based on composition and spray parameters. The bond coat/top coat interface morphology and sample cross sections were examined by SEM and optical microscopy. The failure morphology following the cyclic oxidation testing will be discussed in relationship to the properties of the ceramic top coats.

Nesbit, James A.↗
DOE OSTI2024

Status of SAS4A/SASSYS-1 Software Development and Application (FY2024)

SAS4A/SASSYS-1 is a simulation tool used to perform deterministic analysis of anticipated events as well as design basis and beyond design basis accidents for advanced liquid-metal-cooled nuclear reactors. With its origin as SAS1A in the late 1960s, the SAS series of codes has been under continuous use and development for over fifty years. It has been identified as a critical element of safety analysis capabilities for the U.S. Department of Energy and is utilized within industry to perform the transient safety analyses required to support the licensing of Liquid Metal-cooled Fast Reactors (LMFRs). This report summarizes the code development and update activities carried out during FY2024. In FY2024, programmatic activities focused on key improvements to software useability, such as enhanced user interfaces for reactivity feedback modeling, improvements in stability/useability of the Code Manual, and improvements to the acceptance testing infrastructure, including automation of acceptance testing and generation of the Acceptance Testing Report. To support end user applications, an open training was held, a semi-public forum was maintained, and a practical benchmarking and validation matrix was developed which allowed limitations of existing testing capabilities to be assessed. The existing fuel models were also enhanced with improved modeling capabilities and testing for the oxide and annular fuel models.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1972

Experimental methods for geological remote sensing

During the past year a two channel IR technique for discrimination among silicate rocks was tested for a second time, a three channel IR method was tested for the first time, and a new visible-reflective IR ratio method was hypothesized and qualitatively tested for iron oxide recognition. Both the two channel and three channel IR ratios methods were capable of discriminating felsic from mafic rock types. The three-channel ratio values measured by the scanner were found to agree, within reasonable limits, with the values of R calculated from laboratory data. The capability of the three channel method to obtain absolute ratios is accompanied by a costly processing routine. The two channel technique is superior for low thermal contrast scenes about which some ground truth is available because of its speed and economy.

Vincent, R. K.↗
NASA NTRS1973

Thermally resistant polymers for fuel tank sealants

Imide-linked perfluoroalkylene ether polymers, that were developed for the high temperature fuel tank sealant application, are discussed. Modifications of polymer structure and properties were realized through use of a new aromatic dianhydride intermediate containing an ether-linked perfluoroalkylene segment. Tests of thermal, oxidative and hydrolytic stability, fuel resistance, and adhesion are discussed along with tensile strength and elongation results. Efforts to effect a low temperature condensation of amic acid prepolymer to form imide links inside are described.

Webster, J. A.↗
NASA NTRS1973

Flame retardant polyphosphazenes

Six polyphosphazene compositions were prepared by reaction of three bis-tertiary phosphines with two phenyl-s-triazine derived diazides. All six polyphosphazenes produced were completely characterized, four of them were furthermore subjected to isothermal gravimetric analysis, smoke density measurements, flammability and oxidative thermal degradation testing. The results of the characterization studies indicate that only low molecular weight oligomers, possibly of a cyclic structure, were obtained in the polymerization reactions. Despite this, however, two of the materials showed no weight loss after 96 hr at 200 C, one did not autoignite at 500 C in air, and all four self extinguished when exposed to a flame as soon as contact between flame and resin was lost. The only toxic decomposition products to be concerned about were found to be hydrogen cyanide and benzene. Under the conditions employed it was proven, however, that the quantities of toxic products are greatly reduced if no ignition takes place, e.g., if thermal decomposition proceeds at a sufficiently low rate.

Paciorek, K. L.↗
NASA NTRS1975

Exhaust pollutant emissions from swirl-can combustor module arrays at parametric test conditions

Improved designs of swirl-can combustor modules were tested using seven-module arrays in a combustor. The combustor was operated over a pressure range of 69 to 207 N/sq cm, a fuel-air ratio range of 0.015 to 0.046, at a constant inlet air temperature of 733 K, and at reference velocities of 23.9 and 30.6 m/sec. The three designs tested performed with high combustion efficiency at all conditions tested and exhibited oxides of nitrogen emissions substantially lower than that of conventional gas turbine combustors. A correlating parameter used to extrapolate oxides of nitrogen emissions to full power or takeoff conditions for large commercial turbofan engines predicts oxides of nitrogen emissions somewhat higher than those specified in the 1979 government emissions standards.

Mularz, E. J.↗
NASA NTRS1975

An X-ray photoelectron spectroscopy study of nickel and nickel-base alloy surface alterations in simulated hot corrosion conditions with emphasis on eventual application to turbine blade corrosion

The spectra of the pure metals tested and their oxides were used to analyze the patterns obtained for various superalloys. The quantitative results for two superalloys revealed differences between the surface compositions and their behavior under different conditions of oxidation. The following results occurred during the hot corrosion of samples in the presence of Na2So4: a lack of Ti migration; strong effects on Cr; and, a higher speed of alteration of superalloys.

Mateescu, G. D.↗
NASA NTRS1975

Comparison of isothermal and cyclic oxidation behavior of twenty-five commercial sheet alloys at 1150 C

Twenty-five commercial nickel-, iron-, and cobalt-base sheet alloys incorporating chromium or chromium and aluminum additions for oxidation resistance were tested at 1150 C in air for 100 hr in both isothermal and 1-hr cyclic furnace exposures. The alloys were evaluated by sample specific weight change, by type of scale formed, by amount and type of spall, and by sample thickness change and microstructure.-

Barrett, C. A.↗
NASA NTRS1981

Ultra-lean combustion at high inlet temperatures

Combustion at inlet air temperatures of 1100 to 1250 K was studied for application to advanced automotive gas turbine engines. Combustion was initiated by the hot environment, and therefore no external ignition source was used. Combustion was stabilized without a flameholder. The tests were performed in a 12 cm diameter test section at a pressure of 2.5 x 10 to the 5th power Pa, with reference velocities of 32 to 60 m/sec and at maximum combustion temperatures of 1350 to 1850 K. Number 2 diesel fuel was injected by means of a multiple source fuel injector. Unburned hydrocarbons emissions were negligible for all test conditions. Nitrogen oxides emissions were less than 1.9 g NO2/kg fuel for combustion temperatures below 1680 K. Carbon monoxide emissions were less than 16 g CO/kg fuel for combustion temperatures greater than 1600 K, inlet air temperatures higher than 1150 K, and residence times greater than 4.3 microseconds.

Anderson, D. N.↗
NASA NTRS1981

Ultra-lean combustion at high inlet temperatures

Combustion at inlet-air temperatures of 1100 to 1250 K was studied for application to advanced automotive gas turbine engines. Combustion was initiated by the hot environment, and therefore no external ignition source was used. Combustion was stabilized without a flameholder. The tests were performed in a 12-cm-diameter test section at a pressure of 250,000 Pa, with reference velocities of 32 to 60 m/s and at maximum combustion temperatures of 1350 to 1850 K. Number 2 diesel fuel was injected by means of a multiple-source fuel injector. Unburned hydrocarbon emissions were negligible for all test conditions. Nitrogen oxide emissions were less than 1.9 g NO2/kg fuel for combustion temperatures below 1680 K. Carbon monoxide emissions were less than 16 g CO/kg fuel for combustion temperatures greater than 1600 K, inlet-air temperatures higher than 1150 K, and residence times greater than 4.3 ms.

Anderson, D. N.↗
NASA NTRS1995

Surface contamination analysis technology team overview

A team was established which consisted of representatives from NASA (Marshall Space Flight Center and Langley Research Center), Thiokol Corporation, the University of Alabama in Huntsville, AC Engineering, SAIC, Martin Marietta, and Aerojet. The team's purpose was to bring together the appropriate personnel to determine what surface inspection techniques were applicable to multiprogram bonding surface cleanliness inspection. In order to identify appropriate techniques and their sensitivity to various contaminant families, calibration standards were developed. Producing standards included development of consistent low level contamination application techniques. Oxidation was also considered for effect on inspection equipment response. Ellipsometry was used for oxidation characterization. Verification testing was then accomplished to show that selected inspection techniques could detect subject contaminants at levels found to be detrimental to critical bond systems of interest. Once feasibility of identified techniques was shown, selected techniques and instrumentation could then be incorporated into a multipurpose inspection head and integrated with a robot for critical surface inspection. Inspection techniques currently being evaluated include optically stimulated electron emission (OSEE); near infrared (NIR) spectroscopy utilizing fiber optics; Fourier transform infrared (FTIR) spectroscopy; and ultraviolet (UV) fluorescence. Current plans are to demonstrate an integrated system in MSFC's Productivity Enhancement Complex within five years from initiation of this effort in 1992 assuming appropriate funding levels are maintained. This paper gives an overview of work accomplished by the team and future plans.

Burns, H. Dewitt↗
NASA NTRS2000

Current status of environmental barrier coatings for Si-Based ceramics

Silicon-based ceramics are the leading candidates for high temperature structural components in next generation gas turbine engines. One key drawback of silicon-based ceramics for such an application is volatilization of the protective silica scale in water vapor and the resulting rapid ceramic recession. Therefore, the realization of Si-based ceramics components in advanced gas turbine engines depends on the development of protection schemes from water vapor attack. Currently, plasma-sprayed external environmental barrier coatings (EBCs) arc the most promising approach. In the late 1980s and early 1990s a wide range of refractory oxide materials were tested as coatings on Si-based ceramics to provide protection from hot corrosion. After the discovery of silica volatilization in water vapor in the early 1990s, the focus of EBC development research has been shifted towards the protection from water vapor attack. Experience learned form the earlier coating developmental effort provided the foundation upon which more complex and advanced EBC coatings have been developed. This paper will discuss the brief history and the current status of EBC development for Si-based ceramics with the main focus on water vapor protection.

Lee, K. N.↗