Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “OPTICAL REFLECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Laser space rendezvous and docking system trade-off study

The use, design, and fabrication feasibility of scanning the laser beam by swiveling the outside mirror with a ball joint swivel system is examined along with the applicability of graphite reinforced epoxy material for the construction of reflective optics. It is indicated that (1) the cost of graphite-epoxy will be more than that of many other materials due to the amount of special tooling required; (2) the weight advantage of graphite-epoxy over beryllium is minimal; the ball joint swivel system is accurate enough to perform the scanning function; and that the ball joint will result in a simpler and more cost effective scanning mechanism.

Adelman, S.↗

Cooled infrared telescope development

The feasibility of the design concept for a 1-m-aperture, cryogenically cooled telescope for Spacelab is assessed. The device makes use of double-folded Gregorian reflective optics. The planned cryogen is helium, and beryllium will be used for the 1.2 m primary mirror. Results of studies based on smaller instruments indicate that no new technology will be required to construct a Shuttle Infrared Telescope Facility which will offer improvement over the sensitivity of conventional telescopes by a factor of 1000 at 10 micrometers.

Young, L. S.↗

Electrical, magnetic, and optical properties of the tetrathiafulvalene /TTF/ pseudohalides, /TTF/12/SCN/7 and /TTF/12/SeCN/7

The electrical, magnetic, and optical properties of charge-transfer salts containing tetrathiafulvalene (TTF) and the pseudohalides, thiocyanate (SCN) and selenocyanate (SeCN), have been investigated. These salts are quasi-one-dimensional compounds containing cation radicals only, in contrast to a cation-radical-anion-radical system, such as tetrathiafulvalene tetracyanoquinodimethane (TTF) (TCNQ). Measurements of electrical conductivity, thermoelectric power, and optical reflectivity of single crystals of the nonstoichiometric salts (TTF)12(SCN)7 and (TTF)12(SeCN)7 show metal-like characteristics above 200 K (high-temperature region). The conductivities at room temperature are approximately 750 mho/cm comparable to those found in (TTF) (TCNQ), and increase with decreasing temperature down to approximately 200 K. The thermoelectric power at room temperature is small and positive (approximately 9 microvolts/deg K), and decreases linearly with decreasing temperature in this region (as expected for metal-like hole conduction along the TTF chains). The ESR intensity, however, decreases with decreasing temperature above 200 K. At 170 K a metal-nonmetal transition occurs, and the transport and magnetic properties below this temperature are characteristic of a semiconducting state.

Somoano, R. B.↗

Large-volume multiple-path nuclear-pumped laser

Output of nuclear pumped laser is increased using mirrors, so multiple optical reflections enlarge lasing-mode volume. Design requires comparatively low thermal neutron flux, uses flux more efficiently. Flux for lasing approaches that available from steady-state reactor. Outputs over 100 watts have been reached.

Hohl, F.↗

Absolute line strengths in nu4, /C-12/H4 - A dual-beam diode laser spectrometer with sweep integration

A tunable diode laser spectrometer with several unique features has been developed for use in the middle IR. The all-reflective optical system has a dual-beam configuration before the dispersive mode selector to eliminate transit-angle errors at the calibration etalon. By maintaining separated beams through the mode selector, beam combiner losses are avoided. Averaging successive sweeps of the current-modulated laser permits stable reproducible spectral integrations, eliminating etalon thermal errors and producing high photometric sensitivity. Line strengths have been measured using this instrument for eleven transitions in nu4 of (C-12)H4. These include R0 and R1 and nine P-branch transitions in the 1202-1263-per cm range. Techniques for measuring strengths with a diode laser are discussed.

Jennings, D. E.↗

Study of the effects of impurities on the properties of silicon materials and performance of silicon solar cell

The effect of silicon film thickness on the energy conversion efficiency of a back surface field solar cell is investigated. A computer-aided design study on the dependence of efficiency peaks on the concentrations of the recombination and dopant impurities is presented. The illuminated current voltage characteristics of over 100 cell designs were obtained using the transmission line circuit model to numerically solve the Shockley Equations. Using an AM1 efficiency of 17% as a target value, it is shown that the efficiency versus thickness dependence has a broad maximum which varies less than 1% over more than three-to-one range of cell thickness from 30 to 100 microns. Optical reflecting back surface will give only a slight improvement of AM1 efficiency, about 0.7%, in this thickness range. The sensitive dependence of efficiency on patchiness across the back surface field, low high junction in thin cells is noted.

Sah, C. T.↗

A 10 micron heterodyne receiver for ultra high resolution astronomical spectroscopy

An improved CO2 laser heterodyne spectrometer is examined. The present system uses reflective optics to eliminate refocusing at different wavelengths, and the local oscillator is a line-center-stabilized isotopic CO2 laser. A tunable diffraction grating makes possible easy and rapid selection of over 50 transitions per isotope of CO2. The IF (0 to 1.6 GHz) from the HgCdTe photomizer is analyzed by a 128-channel filter bank, consisting of 64 tunable 5-MHz filters and 64 fixed 25-MHz RF filters. These filters provide resolving powers of about 1,000,000 to 10,000,000 and velocity resolution of 50 to 250 m/sec; their output is synchronously detected, integrated, multiplexed and stored in a buffer memory for the desired integration period. Kitt Peak observations show the wide spectral coverage, wide mixer and electronics bandwidth, and high sensitivity of the system.

Buhl, D.↗

EUV spectroscopic plasma diagnostics for the solar wind acceleration region

Possibilities are considered for probing physical conditions in the solar corona with strong EUV resonance lines from ions such as N V, O VI, Ne VIII, Mg X, and Si XII. Through measurements of the intensities and profiles of EUV spectral lines with coronagraphic instrumentation employing normal incidence reflecting optics, it is possible to acquire information on electron, proton, and ion temperatures and velocity distributions; electron, H I, and ion densities; mass flow and nonthermal velocities; and chemical abundances. This information will provide critical empirical constraints on physical processes responsible for plasma heating, solar wind acceleration, and transport of mass, momentum, and energy in the solar corona, as well as providing constraints on theoretical models for solar and stellar coronae and mass loss.

Kohl, J. L.↗

Effect of thickness on silicon solar cell efficiency

A computer-aided-design study on the dependence of the efficiency peak of a back-surface field solar cell on the concentrations of the recombination and dopant impurities is presented. The illuminated current-voltage characteristics of more than 100 cell designs are obtained using the transmission line circuit model to numerically solve the Shockley equations. Using an AM 1 efficiency of 17% as a target value, it is shown that the efficiency versus thickness dependence has a broad maximum which varies by less than 1% over more than a three-to-one range of cell thicknesses from 30 to 100 microns. An optically reflecting back surface will give only a slight improvement of AM 1 efficiency, about 0.7%, in this thickness range. Attention is given to the dependence of the efficiency on patchiness across the back-surface field low-high junction in thin cells.

Sah, C.-T.↗

The gridded back contact and its effect on solar cell performance

The effect of using gridded back contacts on silicon solar cells made with Al baked surface field (BSF) was experimentally investigated and found to result in a significant increase in conversion efficiency due to higher short-circuit current. An increase of 5 to 8% was noted for thin cells while a smaller increase was observed for standard thickness cells. Several possible explanatory mechanisms are suggested and summarized, including stress relief, incomplete BSF formation, improved back surface recombination velocity, and improved optical reflection off the back silicon-air interface.

Giuliano, M.↗

Solar corona at high resolution

The earth's surface is shielded from solar X rays almost completely by the atmosphere. It is, therefore, necessary to place X-ray detectors on rockets or orbiting satellites. Solar rays were detected for the first time in the late 1940's, using V-2 rockets. In 1960, the first true X-ray images of the sun were obtained with the aid of a simple pinhole camera. The spatial resolution of the X-ray images could be considerably improved by making use of reflective optics, operating at grazing incidence. Aspects of X-ray mirror developments are discussed along with the results obtained in coronal studies utilizing the new devices for the observation of solar X-ray emission. It is pointed out that the major achievements of the Skylab missions were due primarily to the unique opportunity to obtain data over an extended period of time. Attention is given to normal incidence X-ray optics, achievements possible by making use of high spatial resolution optics, and details of improved mirror design.

Golub, L.↗

Characteristic morphological and frictional changes in sputtered MoS/sub 2 films

Three microstructural growth stages of sputtered MoS2 films were identified with respect to film thickness: (1) ridge formation during nucleation, (2) an equiaxed transition zone, and (3) a columnar-fiber-like structure. Each of these growth stages are characterized in terms of microcrystallite size, shape, and orientation. The effective lubricating film thickness is established in terms of the microstructural growth stages during sliding experiments. The film has a tendency to break up within the columnar zone. Actual lubrication is performed by the remaining film which is 0.18 to 0.22 microns thick. Also a visual screening is proposed to evaluate the integrity of the as-sputtered MoS2 film. The lubricating properties are identified with respect to optical changes before and after wiping. The orientation of the microcrystallites are responsible for the optical reflective changes observed.

Spalvins, T.↗

Factors limiting the discrimination and quantification of terrestrial features using remotely sensed radiance

In this paper, factors controlling the radiance incident on a remote-sensing device and the interaction of the sensor with upwelling radiance are considered. Attention is also given to systematic and random radiance variations across an image: while the former may be corrected for (to an extent) the latter may not, so that it is necessary to be aware of the impact of random variations on target identification, discrimination and quantification. Both the optical reflective and the thermal-infrared parts of the spectrum are considered. Equations are presented to concisely illustrate the processes involved.

Duggin, M. J.↗

Prepreg cure monitoring using diffuse reflectance-FTIR

An in situ diffuse reflectance-Fourier transform infrared technique was developed to determine infrared spectra of graphite fiber prepregs as they were being cured. A bismaleimide, an epoxy, and addition polyimide matrix resin prepregs were studied. An experimental polyimide adhesive was also examined. Samples were positioned on a small heater at the focal point of diffuse reflectance optics and programmed at 15 F/min while FTIR spectra were being scanned, averaged, and stored. An analysis of the resulting spectra provided basic insights into changes in matrix resin molecular structure which accompanied reactions such as imidization and crosslinking. An endo-exothermal isomerization involving reactive end-caps was confirmed for the addition polyimide prepregs. The results of this study contribute to a fundamental understanding of the processing of composites and adhesives. Such understanding will promote the development of more efficient cure cycles.

Young, P. R.↗

Aperture-synthesis observations of carbon monoxide in the Egg Nebula

Observations of the 2.6-mm CO emission of the bipolar nebular CRL 2688, obtained with resolution 7 arcsec using the mm-wave interferometer at Owens Valley during December 1982-June 1983, are reported. The emission of a 10 x 15-arcsec core, centered on the optical reflection nebula and probably surrounded by a large cloud of cooler gas, is found to have a main-axis velocity gradient of 3 km/s arcsec and an excitation temperature of about 70 K.

Heiligman, G. M.↗

Experimental, water droplet impingement data on two-dimensional airfoils, axisymmetric inlet and Boeing 737-300 engine inlet

An experimental method has been developed to determine the droplet impingement characteristics on two- and three-dimensional bodies. The experimental results provide the essential droplet impingement data required to validate particle trajectory codes, used in aircraft icing analyses and engine inlet particle separator analyses. A body whose water droplet impingement characteristics are required is covered at strategic locations by thin strips of moisture absorbing (blotter) paper, and then exposed to an air stream containing a dyed-water spray cloud. Water droplet impingement data are extracted from the dyed blotter strips, by measuring the optical reflectance of the dye deposit on the strips, using an automated reflectometer. Impingement efficiency data obtained for a NACA 65(2)015 airfoil section, a supercritical airfoil section, and Being 737-300 and axisymmetric inlet models are presented in this paper.

Papadakis, M.↗

Stable 1.25 watts CW far infrared laser radiation at the 119 micron methanol line

Far-infrared CW radiation of 1.25 watts has been obtained at the 119 micron methanol line with a CO2 pump power of 125 watts, and the maximum frequency fluctuation of the free running laser is measured to be less than + or - 100 kHz per hour. Reflecting optics have been used, when possible, to minimize CO2 degradation, and the frequency stability is ensured by cooling the input and output couplers. The input and output assemblies within the lasing medium are enclosed to minimize the external effects on the cavity length and to eliminate the mechanical instabilities associated with the use of bellows. The vibrational bottle-neck is broken by cooling the resonator wall to 5 deg and adding He as the buffer gas.

Farhoomand, Jam↗

C II 158 micron and O I 63 micron observations of NGC 7023 - A model for its photodissociation region

Emission in the far IR fine-structure lines of O I (63 microns) and C II (158 microns) from the bright optical reflection nebula NGC 7023 has been observed. It is suggested that this emission arises in a warm, atomic photodissociation region produced by the interaction of the UV radiation of the illuminating star with a molecular cloud. The density and temperature in the photodissociation region is estimated and a model for the region is constructed.

Chokshi, A.↗