SEARCH · Engineering Papers

Results for “Modal Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

NASA NTRS2015

Rapid State Space Modeling Tool for Rectangular Wing Aeroservoelastic Studies

This paper introduces a modeling and simulation tool for aeroservoelastic analysis of rectangular wings with trailing-edge control surfaces. The inputs to the code are planform design parameters such as wing span, aspect ratio, and number of control surfaces. Using this information, the generalized forces are computed using the doublet-lattice method. Using Roger's approximation, a rational function approximation is computed. The output, computed in a few seconds, is a state space aeroservoelastic model which can be used for analysis and control design. The tool is fully parameterized with default information so there is little required interaction with the model developer. All parameters can be easily modified if desired. The focus of this paper is on tool presentation, verification, and validation. These processes are carried out in stages throughout the paper. The rational function approximation is verified against computed generalized forces for a plate model. A model composed of finite element plates is compared to a modal analysis from commercial software and an independently conducted experimental ground vibration test analysis. Aeroservoelastic analysis is the ultimate goal of this tool, therefore, the flutter speed and frequency for a clamped plate are computed using damping-versus-velocity and frequency-versus-velocity analysis. The computational results are compared to a previously published computational analysis and wind-tunnel results for the same structure. A case study of a generic wing model with a single control surface is presented. Verification of the state space model is presented in comparison to damping-versus-velocity and frequency-versus-velocity analysis, including the analysis of the model in response to a 1-cos gust.

Modeling and Simulation↗

NASA NTRS2014

Rapid State Space Modeling Tool for Rectangular Wing Aeroservoelastic Studies

This paper introduces a modeling and simulation tool for aeroservoelastic analysis of rectangular wings with trailing edge control surfaces. The inputs to the code are planform design parameters such as wing span, aspect ratio and number of control surfaces. A doublet lattice approach is taken to compute generalized forces. A rational function approximation is computed. The output, computed in a few seconds, is a state space aeroservoelastic model which can be used for analysis and control design. The tool is fully parameterized with default information so there is little required interaction with the model developer. Although, all parameters can be easily modified if desired.The focus of this paper is on tool presentation, verification and validation. This process is carried out in stages throughout the paper. The rational function approximation is verified against computed generalized forces for a plate model. A model composed of finite element plates is compared to a modal analysis from commercial software and an independently conducted experimental ground vibration test analysis. Aeroservoelastic analysis is the ultimate goal of this tool. Therefore the flutter speed and frequency for a clamped plate are computed using V-g and V-f analysis. The computational results are compared to a previously published computational analysis and wind tunnel results for the same structure. Finally a case study of a generic wing model with a single control surface is presented. Verification of the state space model is presented in comparison to V-g and V-f analysis. This also includes the analysis of the model in response to a 1-cos gust.

Modeling and Simulation↗

NASA NTRS2015

Rapid State Space Modeling Tool for Rectangular Wing Aeroservoelastic Studies

This report introduces a modeling and simulation tool for aeroservoelastic analysis of rectangular wings with trailing-edge control surfaces. The inputs to the code are planform design parameters such as wing span, aspect ratio, and number of control surfaces. Using this information, the generalized forces are computed using the doublet-lattice method. Using Roger's approximation, a rational function approximation is computed. The output, computed in a few seconds, is a state space aeroservoelastic model which can be used for analysis and control design. The tool is fully parameterized with default information so there is little required interaction with the model developer. All parameters can be easily modified if desired. The focus of this report is on tool presentation, verification, and validation. These processes are carried out in stages throughout the report. The rational function approximation is verified against computed generalized forces for a plate model. A model composed of finite element plates is compared to a modal analysis from commercial software and an independently conducted experimental ground vibration test analysis. Aeroservoelastic analysis is the ultimate goal of this tool, therefore, the flutter speed and frequency for a clamped plate are computed using damping-versus-velocity and frequency-versus-velocity analysis. The computational results are compared to a previously published computational analysis and wind-tunnel results for the same structure. A case study of a generic wing model with a single control surface is presented. Verification of the state space model is presented in comparison to damping-versus-velocity and frequency-versus-velocity analysis, including the analysis of the model in response to a 1-cos gust.

Verification and Validation↗

NASA NTRS2014

Coupled Fluid-Structure Interaction Analysis of Solid Rocket Motor with Flexible Inhibitors

Flexible inhibitors are generally used in solid rocket motors (SRMs) as a means to control the burning of propellant. Vortices generated by the flow of propellant around the flexible inhibitors have been identified as a driving source of instabilities that can lead to thrust oscillations in launch vehicles. Potential coupling between the SRM thrust oscillations and structural vibration modes is an important risk factor in launch vehicle design. As a means to predict and better understand these phenomena, a multidisciplinary simulation capability that couples the NASA production CFD code, Loci/CHEM, with CFDRC's structural finite element code, CoBi, has been developed. This capability is crucial to the development of NASA's new space launch system (SLS). This paper summarizes the efforts in applying the coupled software to demonstrate and investigate fluid-structure interaction (FSI) phenomena between pressure waves and flexible inhibitors inside reusable solid rocket motors (RSRMs). The features of the fluid and structural solvers are described in detail, and the coupling methodology and interfacial continuity requirements are then presented in a general Eulerian-Lagrangian framework. The simulations presented herein utilize production level CFD with hybrid RANS/LES turbulence modeling and grid resolution in excess of 80 million cells. The fluid domain in the SRM is discretized using a general mixed polyhedral unstructured mesh, while full 3D shell elements are utilized in the structural domain for the flexible inhibitors. Verifications against analytical solutions for a structural model under a steady uniform pressure condition and under dynamic modal analysis show excellent agreement in terms of displacement distribution and eigenmode frequencies. The preliminary coupled results indicate that due to acoustic coupling, the dynamics of one of the more flexible inhibitors shift from its first modal frequency to the first acoustic frequency of the solid rocket motor. This insight could have profound implications for SRM and flexible inhibitor designs for current and future launch vehicles including SLS.

Yang, H. Q.↗

NASA NTRS1981

Analytical testing

Analytical methods for combining flight acceleration and strain data with shake test mobility data to predict the effects of structural changes on flight vibrations and strains are presented. This integration of structural dynamic analysis with flight performance is referred to as analytical testing. The objective of this methodology is to analytically estimate the results of flight testing contemplated structural changes with minimum flying and change trials. The category of changes to the aircraft includes mass, stiffness, absorbers, isolators, and active suppressors. Examples of applying the analytical testing methodology using flight test and shake test data measured on an AH-1G helicopter are included. The techniques and procedures for vibration testing and modal analysis are also described.

Flannelly, W. G.↗

NASA NTRS1987

Effect of Helicopter Blade Dynamics on Blade Aerodynamic and Structural Loads

The effect of rotor blade dynamics on aerodynamic and structural loads is examined for a conventional, main- rotor helicopter using both a comprehensive rotorcraft analysis (CAMRAD) and night test data. The impact of blade dynamics on blade section lift-coefficient time histories is studied by comparing predictions from both a rigid blade analysis and an elastic blade analysis with helicopter flight test data. The elastic blade analysis better predicts high-frequency behavior of section lift. In addition, components of the blade angle of attack, such as elastic blade twist, blade nap rate, blade slope velocity, and inflow, are examined as a function of blade mode. Elastic blade motion affects the blade angle of attack by a few tenths of a degree, and up to the sixth rotor harmonic. A similar study of the influence of blade dynamics on bending and torsion moments was also conducted. The modal analysis of the predicted blade structural loads suggested that five elastic bending deg of freedom (four flap and one lag) and three elastic torsion deg of freedom contributed to calculations of the blade structural loads. However, when structural bending load predictions from several elastic blade analyses were compared with flight test data, an elastic blade model consisting of only three elastic bending modes (first and second flap, and first lag), and two elastic torsion modes was found to be sufficient for maximum correlation.

Heffernan, Ruth M.↗

NASA NTRS1990

Computation of rotor aerodynamic loads in forward flight using a full-span free wake analysis

The development of an advanced computational analysis of unsteady aerodynamic loads on isolated helicopter rotors in forward flight is described. The primary technical focus of the development was the implementation of a freely distorting filamentary wake model composed of curved vortex elements laid out along contours of constant vortex sheet strength in the wake. This model captures the wake generated by the full span of each rotor blade and makes possible a unified treatment of the shed and trailed vorticity in the wake. This wake model was coupled to a modal analysis of the rotor blade dynamics and a vortex lattice treatment of the aerodynamic loads to produce a comprehensive model for rotor performance and air loads in forward flight dubbed RotorCRAFT (Computation of Rotor Aerodynamics in Forward Flight). The technical background on the major components of this analysis are discussed and the correlation of predictions of performance, trim, and unsteady air loads with experimental data from several representative rotor configurations is examined. The primary conclusions of this study are that the RotorCRAFT analysis correlates well with measured loads on a variety of configurations and that application of the full span free wake model is required to capture several important features of the vibratory loading on rotor blades in forward flight.

Quackenbush, Todd R.↗

DOE OSTI2014

Dynamic behaviour of thin composite plates for different boundary conditions

In the context of composite materials technology, which is increasingly present in industry, this article covers a topic of great interest and theoretical and practical importance. Given the complex design of fiber-reinforced materials and their heterogeneous nature, mathematical modeling of the mechanical response under different external stresses is very difficult to address in the absence of simplifying assumptions. In most structural applications, composite structures can be idealized as beams, plates, or shells. The analysis is reduced from a three-dimensional elasticity problem to a oneor two-dimensional problem, based on certain simplifying assumptions that can be made because the structure is thin. This paper aims to validate a mathematical model illustrating how thin rectangular orthotropic plates respond to the actual load. Thus, from the theory of thin plates, new analytical solutions are proposed corresponding to orthotropic rectangular plates having different boundary conditions. The proposed analytical solutions are considered both for solving equation orthotropic rectangular plates and for modal analysis.

36 MATERIALS SCIENCE↗

NASA NTRS2004

Reduced-Order Modeling and Wavelet Analysis of Turbofan Engine Structural Response Due to Foreign Object Damage (FOD) Events

The development of a wavelet-based feature extraction technique specifically targeting FOD-event induced vibration signal changes in gas turbine engines is described. The technique performs wavelet analysis of accelerometer signals from specified locations on the engine and is shown to be robust in the presence of significant process and sensor noise. It is envisioned that the technique will be combined with Kalman filter thermal/health parameter estimation for FOD-event detection via information fusion from these (and perhaps other) sources. Due to the lack of high-frequency FOD-event test data in the open literature, a reduced-order turbofan structural model (ROM) was synthesized from a finite element model modal analysis to support the investigation. In addition to providing test data for algorithm development, the ROM is used to determine the optimal sensor location for FOD-event detection. In the presence of significant noise, precise location of the FOD event in time was obtained using the developed wavelet-based feature.

Turso, James↗

NASA NTRS1972

The stability of motion of satellites with flexible appendages

The mathematical formulation associated with the problem of stability of motion of a satellite consisting of a main rigid body and three (or less) pairs of flexible rods is presented. The rods are capable of flexure in two orthogonal directions. Whereas the rotational motion of the body is described by generalized coordinates depending on time alone, the elastic displacements of the rods depend both on spatial position and time. Assuming no external torques, there exist motion integrals in the form of momentum integrals. These integrals can be regarded as constraint equations relating the system velocities, and used to reduce the number of variables describing the motion. The stability analysis has been carried out by means of an extension of the Liapunov direct method. Since the elastic vibrations result in energy dissipation, it is shown that the equilibrium position is asymptotically stable if the Hamiltonian is positive definite and unstable if it can take negative values in the neighborhood of the equilibrium. Determining the sign definiteness of the Hamiltonian is complicated by the fact that it contains spatial derivatives of the elastic displacements. Two methods are presented to cope with this problem. The first, the standard modal analysis in conjunction with series truncation, develops criteria in terms of infinite series associated with the natural modes and frequencies of the elastic rods. The second, the method of integral coordinates, yields closed-form stability criteria involving the system parameters, such as the body moments of inertia, the length and mass distribution of the rods, the lowest natural frequencies of the rods, and the satellite spin velocity.

Meirovitch, L.↗

NASA NTRS1987

Vibratory response of a stiffened, floor equipped, composite cylinder

A structural modal analysis has been performed on a composite, filament wound cylindrical shell with floor, using a Computer Aided Test (CAT) system. The twelve foot (3.66 m) long shell is five and one half feet (1.68 m) in diameter and includes a half inch thick plywood floor attached to the shell 69 degrees from the vertical centerline through the bottom of the shell. The shell is composed of carbon fibers embedded in an epoxy resin. The cylinder is supported by two heavy, rigid endcaps simulating simply supported end conditions. Modal frequencies of the shell and floor have been extracted by measuring the frequency response functions from impulse excitation by an impact hammer. Reasonable agreement is obtained between the measured structural modal frequencies and mode shapes and analytical results from a computerized prediction model. The effects of floor location, fiber orientation, and skin thickness on the resonance frequencies of the shell and floor have been predicted for a stiffened and unstiffened cylinder.

Grosveld, Ferdinand W.↗

NASA NTRS2007

Reduced-Order Modeling and Wavelet Analysis of Turbofan Engine Structural Response Due to Foreign Object Damage "FOD" Events

The development of a wavelet-based feature extraction technique specifically targeting FOD-event induced vibration signal changes in gas turbine engines is described. The technique performs wavelet analysis of accelerometer signals from specified locations on the engine and is shown to be robust in the presence of significant process and sensor noise. It is envisioned that the technique will be combined with Kalman filter thermal/ health parameter estimation for FOD-event detection via information fusion from these (and perhaps other) sources. Due to the lack of high-frequency FOD-event test data in the open literature, a reduced-order turbofan structural model (ROM) was synthesized from a finite-element model modal analysis to support the investigation. In addition to providing test data for algorithm development, the ROM is used to determine the optimal sensor location for FOD-event detection. In the presence of significant noise, precise location of the FOD event in time was obtained using the developed wavelet-based feature.

Turso, James A.↗

NASA NTRS2016

Extracting Damping Ratio from Dynamic Data and Numerical Solutions

There are many ways to extract damping parameters from data or models. This Technical Memorandum provides a quick reference for some of the more common approaches used in dynamics analysis. Described are six methods of extracting damping from data: the half-power method, logarithmic decrement (decay rate) method, an autocorrelation/power spectral density fitting method, a frequency response fitting method, a random decrement fitting method, and a newly developed half-quadratic gain method. Additionally, state-space models and finite element method modeling tools, such as COMSOL Multiphysics (COMSOL), provide a theoretical damping via complex frequency. Each method has its advantages which are briefly noted. There are also likely many other advanced techniques in extracting damping within the operational modal analysis discipline, where an input excitation is unknown; however, these approaches discussed here are objective, direct, and can be implemented in a consistent manner.

Casiano, M. J.↗

NASA NTRS1976

Optimization of suppression for two-element treatment liners for turbomachinery exhaust ducts

Sound wave propagation in a soft-walled rectangular duct with steady uniform flow was investigated at exhaust conditions, incorporating the solution equations for sound wave propagation in a rectangular duct with multiple longitudinal wall treatment segments. Modal analysis was employed to find the solution equations and to study the effectiveness of a uniform and of a two-sectional liner in attenuating sound power in a treated rectangular duct without flow (M = 0) and with uniform flow of Mach 0.3. Two-segment liners were shown to increase the attenuation of sound as compared to a uniform liner. The predicted sound attenuation was compared with measured laboratory results for an optimized two-segment suppressor. Good correlation was obtained between the measured and predicted suppressions when practical variations in the modal content and impedance were taken into account. Two parametric studies were also completed.

Motsinger, R. E.↗

NASA NTRS1988

Probabilistic structural analysis computer code (NESSUS)

Probabilistic structural analysis has been developed to analyze the effects of fluctuating loads, variable material properties, and uncertain analytical models especially for high performance structures such as SSME turbopump blades. The computer code NESSUS (Numerical Evaluation of Stochastic Structure Under Stress) was developed to serve as a primary computation tool for the characterization of the probabilistic structural response due to the stochastic environments by statistical description. The code consists of three major modules NESSUS/PRE, NESSUS/FEM, and NESSUS/FPI. NESSUS/PRE is a preprocessor which decomposes the spatially correlated random variables into a set of uncorrelated random variables using a modal analysis method. NESSUS/FEM is a finite element module which provides structural sensitivities to all the random variables considered. NESSUS/FPI is Fast Probability Integration method by which a cumulative distribution function or a probability density function is calculated.

Shiao, Michael C.↗

DOE OSTI2019

Digital signal processing in coupled photonic crystal waveguides and its application to an all-optical AND logic gate

The realization of all-optical AND logic gates for pulsed signal operation based on the photonic bandgap transmission phenomenon is proposed. We are using realistic planar air-hole type coupled photonic crystal waveguides (C-PCWs) with Kerr-type nonlinear background medium. The novelty of our analysis is that the proposed AND logic gate operates with the temporal solitons, which maintain a stable envelope propagating in the nonlinear C-PCWs, enabling true ultrafast full-optical digital signal processing in the time-domain. The bandgap transmission takes place when the operating frequency is chosen at the very edge of the dispersion curve of one of the supermodes in the C-PCWs. In this regard, our original fast and accurate method is used to efficiently calculate the supermodes of the C-PCW system. The underlying semi-analytical full-wave modal analysis is based on the evaluation of the lattice sums for complex wavenumbers using the transition-matrix method in combination with the generalized reflection-matrix approach. As a proof of concept successful pulse operation of the all-optical AND logic gate is demonstrated in the framework of extensive full-wave finite-difference time-domain electromagnetics analysis.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

NASA NTRS1977

Test of a model for trace element partition during closed-system solidification of a silicate liquid

Trace-element concentrations in separated minerals and rock fragments from a coarsely crushed and sieved sample of medium-grained lunar basalt are determined by high-precision instrumental neutron activation analysis for three main purposes. These are: (1) to test a previously proposed model for describing trace-element behavior during solidification of a silicate liquid under conditions of a closed system; (2) to compare trace-element concentrations among different size fractions of a comminuted basalt; and (3) to investigate small-scale heterogeneity within a single medium-grained basalt. It is found that an excellent mass balance for the whole rock is attained in terms of the trace-element concentrations of the component minerals and mesostasis, that the mixing model describing this mass balance yields a superior modal analysis for the whole rock, and that different size fractions of the coarsely crushed basalt vary in mineral composition. The closed-system model is shown to account properly for the average behavior of the trace elements during solidification of the basalt, and values of distribution coefficients are obtained for incompatible elements in that rock.

Haskin, L. A.↗

NASA NTRS2013

Development of an Aeroelastic Modeling Capability for Transient Nozzle Side Load Analysis

Lateral nozzle forces are known to cause severe structural damage to any new rocket engine in development during test. While three-dimensional, transient, turbulent, chemically reacting computational fluid dynamics methodology has been demonstrated to capture major side load physics with rigid nozzles, hot-fire tests often show nozzle structure deformation during major side load events, leading to structural damages if structural strengthening measures were not taken. The modeling picture is incomplete without the capability to address the two-way responses between the structure and fluid. The objective of this study is to develop a coupled aeroelastic modeling capability by implementing the necessary structural dynamics component into an anchored computational fluid dynamics methodology. The computational fluid dynamics component is based on an unstructured-grid, pressure-based computational fluid dynamics formulation, while the computational structural dynamics component is developed in the framework of modal analysis. Transient aeroelastic nozzle startup analyses of the Block I Space Shuttle Main Engine at sea level were performed. The computed results from the aeroelastic nozzle modeling are presented.

Wang, Ten-See↗