SEARCH · Engineering Papers

Results for “Microstructures, and Modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Modeling deformation and failure in AlSi-polyester abradable sealcoating material using microstructure-based finite element simulation

A plasma-sprayed aluminum-silicon (AlSi)/polyester coating is applied in modern gas turbine engines as an abradable sealcoating to maintain tight clearances between the rotating blades and the static casing. While running the engine, the rotating blades “rub” with the abradable coating, which results in extreme strain rate (up to 10 6 ) dynamics and a high-temperature environment. Due to the difficulty of collecting direct measurements, predictive computational models are important for analyzing the deformation and failure of the abradable material, to help meet the design target of avoiding damage to the blade tip and maintaining high fuel efficiency. In this research, a microstructure-based finite element (FE) computational model was developed to capture the complex mechanical behavior of the AlSi/polyester microstructure. The model is based on a virtual representative-volume-element (RVE) of a metal-polymer microstructure, reconstructed from x-ray computed tomography. It models the plastic deformation of, and damage to, each AlSi and polyester constituents, as well as the failure at their interface. The model was calibrated and validated with uniaxial tension and compression experiments, conducted at two temperatures (298 K and 533 K) at an applied strain rate of 10 3 - 10 4 s -1 . The material exhibited strongly asymmetric tension-compression behavior and a sensitivity to temperature, which was well captured by the model. The model was further applied to investigate changes in mechanical behavior due to variations in constituents’ volume fractions, which provides guidance to the microstructural design of AlSi/polyester abradable materials. The model is expected to facilitate the development of improved abradable materials by bypassing the conventional trial-and-error approach and extensive testing requirements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Understanding coarsening of a post-corrosion microstructure in a molten salt by combining phase-field modeling and in situ tomography

Alloys corroding in molten salt have been observed to form bicontinuous, nanoporous microstructures via dealloying, which subsequently undergo coarsening due to facile transport in high-temperature conditions. In this work, we describe a methodology to elucidate the underlying transport mechanisms during coarsening of a bicontinuous microstructure via quantitative comparisons between phase-field simulations and four-dimensional in situ experiments, in this case X-ray nanotomography of the coarsening of a dealloyed 80 wt% Ni-20 wt% Cr microwire in molten KCl-MgCl 2 at 800°C. We conduct phase-field simulations initialized from experimental data to model coarsening via three different transport mechanisms: surface diffusion, solid bulk diffusion, and liquid bulk diffusion. These simulations reproduce key features of the experiment, such as the densification of the outer layer of the dealloyed wire and the reduction in radius over time. We quantitatively compare different microstructural characteristics between the simulations and experiment and extract temporal scaling factors that optimally match the time scales of the simulations to that of the experiment. This allows us to evaluate morphological similarity between the simulations and experiment and relate the experimental coarsening kinetics to fundamental material properties. We find that surface diffusion is most likely to be the dominant coarsening mechanism, and its kinetics imply a surface diffusivity of D S = 8.9 x 10 -20 m 3 /s, which is within the range of reported values for Ni-vacuum interfaces at 800°C. However, the difference between the experiment and the surface diffusion simulation increases substantially at late times, suggesting that other mechanisms, such as the dissolution of residual Cr, may be at play.

36 MATERIALS SCIENCE↗

NASA NTRSDate not supplied

Cathode Modeling of Solid-State Batteries

The search for safe, reliable, and compact high-capacity energy storage devices has led to increased interest in all-solid-state battery research. The use of solid electrolytes provides enhanced safety and durability due to their reduced flammability and increased mechanical strength compared to organic liquid electrolytes. Still, the use of solid electrolytes remains challenging. Computational modeling plays a substantial role in addressing these challenges. A particle dynamics electromechanical model for simulating electrochemical processes in a solid-state battery cathode will be presented. The model presents cathode microstructure at the particle level as a mixture of ionically conductive solid electrolyte particles, electrically conductive carbon additives, and cathodic reactant particles. After densification, the particle connectivity is analyzed to reconstruct the complex electric network connecting reactant particles with an anodic and cathodic current collectors through the electrolyte and carbon particles. The Kirchhoff’s matrix equation describing this electric network, is solved to obtain values of various critical parameters, such as the overall conductivity of the cathode for lithium ions and electrons, cathodic reactant material utilization, and the distribution of the electric current and voltages within the cathode. In addition, by representing the reactant particles as electrolyte or galvanic microcells governed by the Butler-Volmer electrochemical equation, the overall performance of battery cells during charge or discharge processes, respectively, can be predicted for a given cathodic powder composition. The presented model, executed on a high-performance computing architecture, essentially provides a valuable guidance in designing and developing future solid-state batteries.

solid-state battery↗

NASA NTRS2012

Investigation of Effects of Material Architecture on the Elastic Response of a Woven Ceramic Matrix Composite

To develop methods for quantifying the effects of the microstructural variations of woven ceramic matrix composites on the effective properties and response of the material, a research program has been undertaken which is described in this paper. In order to characterize and quantify the variations in the microstructure of a five harness satin weave, CVI SiC/SiC, composite material, specimens were serially sectioned and polished to capture images that detailed the fiber tows, matrix, and porosity. Open source quantitative image analysis tools were then used to isolate the constituents and collect relevant statistics such as within ply tow spacing. This information was then used to build two dimensional finite element models that approximated the observed section geometry. With the aid of geometrical models generated by the microstructural characterization process, finite element models were generated and analyses were performed to quantify the effects of the microstructure and its variation on the effective stiffness and areas of stress concentration of the material. The results indicated that the geometry and distribution of the porosity appear to have significant effects on the through-thickness modulus. Similarly, stress concentrations on the outer surface of the composite appear to correlate to regions where the transverse tows are separated by a critical amount.

Goldberg, Robert K.↗

DOE OSTI2022

Harnessing structural stochasticity in the computational discovery and design of microstructures

This paper presents a deep generative model-based design methodology for tailoring the structural stochasticity of microstructures. Although numerous methods have been established for designing deterministic (periodic) or stochastic microstructures, a systematic design approach that allows the unified treatment of both deterministic and stochastic microstructure design domains has yet to be created. The proposed methodology resolves this issue by learning a unified feature space that embodies diverse structural patterns with continuously varying stochasticity levels. A highly diverse microstructure database is established to incorporate various types of deterministic and stochastic microstructure patterns. A property-aware deep generative model is proposed to learn a unified feature space of the structural characteristics, as well as the relationship between structure features and properties of interest. Autoencoder (AE), Variational Autoencoder (VAE), and Adversarial Autoencoder (AAE) are compared to understand their relative merits in the property-aware learning of the unified feature space. Microstructural designs with tailorable stochasticity and properties are obtained by searching the unified feature space. Multiple design cases are presented to demonstrate the capability of designing microstructures for structural stochasticity and properties. Furthermore, the proposed method is employed to create stochastically graded structures, which manipulate the mechanical behaviors by varying the local stochasticity of the structure.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Inhomogeneous Distribution and Coarsening of y″ Precipitates in a Ni-Based Superalloy and Their Effect on Creep

It has been reported that the addition of Nb or Ta in the high Ti/Al ratio alloys promotes the formation of y″ precipitates solely and greatly contributes to the elevated temperature strength and resistance to creep deformation. In this study, the y''-dominant INCONEL alloy 725 (IN725) variants (named M725-Nb/Ta) modified with a high level of Nb/Ta additions and high Ti/Al ratio was chosen as a model alloy for microstructural observation of y'' variants upon creep. Following the high temperature aging (HTA), y'' was found to be the main strengthening precipitate with no detectable y’ in both M725 alloys. After creep, the grip/gage sections of the crept M725-Nb/Ta exhibited preferential coarsening and inhomogeneous distribution of y''. That is, one or two of the variants were preferentially coarsened at the expense of another variant, and sandwich-like structures, comprising of cubic y′ precipitates with small y″ discs on each face, were formed. This variant selection behavior taking place in the grip section with no stress applied was different from the typical stress-induced variant selection in previous literature. However, the sample with prior high temperature exposure (700 °C for 500 hours) with varying y″ characteristics demonstrated a similar trend of creep when compared with those in the HTA sample, suggesting that the coarsening and the inhomogeneous distribution of y'' was not the determinant of creep life in bulk M725-Nb/Ta alloys.

Hung, Chang-Yu↗

DOE OSTI2023

Derivation of heterogeneous material distributions and their sensitivity to HM-coupled two-phase flow models exemplified with the LASGIT experiment

Abstract Advective gas transport in bentonite, a possible buffer material in repositories for radioactive materials, is difficult to simulate in numerical continuum models, partly due to the complicated microstructure of bentonite. To generate reliable models of repositories nevertheless, spatially distributed heterogeneous material properties can be used to allow localization of gas flow. In this study, a pore-size-dependent stochastic approach of the gas entry pressure is derived from Mercury Intrusion Porosimetry, which is used to replicate measurements from the LASGIT experiment. In addition, three benchmark tests are simulated to investigate the dependence of heterogeneous distributions of material properties on the mesh discretization, the temporal dependence, and the coupling between the processes influenced by the heterogeneous parameters. The numerical modeling results of the LASGIT experiment show that the onset of gas flow into the system and the subsequent increase in pressure and stress can be well reproduced using heterogeneous distributions. Compared to a model with homogeneous material properties, heterogeneous distributions may allow the generation of dilatancy-controlled microfractures—an important feature with regard to the advective gas flow in bentonites. However, it can be observed that the heterogeneous distributions in LASGIT are less significant, as technical gaps or differences in material types could have a greater impact.

Environmental Sciences & Ecology↗

DOE OSTI2021

Heterogeneous creep deformation behavior of functionally graded transition joints (GTJs)

Dissimilar metal welds (DMWs) made between ferritic steels and austenitic alloys are used extensively in high-temperature power plant components. These DMWs experience premature creep failure in the ferritic steel’s heat affected zone (HAZ), close to the weld interface. Steep variations in microstructure and chemical composition across the dissimilar weld interface have been the contributing factors for the failure. Graded transition joints (GTJs), developed by functionally grading the chemical composition in layers, have been proposed as potential candidates to replace DMWs. In this research, GTJ coupons were fabricated between 2.25Cr-1Mo steel and Alloy 800H base material using two filler materials: (i) Inconel 82 and (ii) P87. These samples were aged at 600°C for 2000h to accelerate high-temperature microstructural evolution seen in service conditions, before subjecting them to short-term (~1 month) creep tests. Surface strains were measured using digital image correlation (DIC) technique to extract creep strain rates at different locations within GTJs. Both the GTJs exhibited heterogeneous creep strain distribution. Creep strain accumulated in the FGHAZ of 2.25Cr-1Mo steel, similar to type IV failure associated with Cr-Mo steel weldments. Microstructure based creep model framework was developed to describe the discrete creep strain rates observed in various 2.25Cr-1Mo steel regions of GTJs.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Microstructure and properties of a high temperature Al–Ce–Mn alloy produced by additive manufacturing

An Al–10Ce-8Mn (wt%) alloy was designed and fabricated by laser powder bed fusion additive manufacturing (AM). The rapid cooling rates of the AM process produced a refined microstructure with a large fraction of reinforcing intermetallic phases. The tensile properties of the alloy were characterized in the as-fabricated state and following thermal exposure. The properties of the as-fabricated microstructure showed exceptional high-temperature performance and strength retention at elevated temperatures up to 400 °C relative to benchmark wrought Al and AM Al alloy properties. Characterization of the microstructure and thermodynamic modeling of the ternary Al–Ce–Mn system rationalized the solidification and solid-state phase transformations. Finally, analysis of the relevant strengthening mechanisms for both the as-fabricated and thermally exposed conditions was performed.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Modeling the thermodynamics of the FeTi hydrogenation under para-equilibrium: An ab-initio and experimental study

We report FeTi-based hydrides have recently re-attracted attention as stationary hydrogen storage materials due to favorable reversibility, good sorption kinetics and relatively low costs compared to alternative intermetallic hydrides. Employing the OpenCalphad software, the thermodynamics of the (FeTi) 1-x H x (0 ≤ x ≤ 1) system were assessed as a key basis for modeling hydrogenation of FeTi-based alloys. New thermodynamic data were acquired from our experimental pressure-composition-isotherm (PCI) curves, as well as first-principles calculations utilizing density functional theory (DFT). The thermodynamic phase models were carefully selected based on critical analysis of literature information and ab-initio investigations. Key thermodynamic properties such as dissociation pressure, formation enthalpies and phase diagrams were calculated in good agreement to our performed experiments and literature-reported data. This work provides an initial perspective, which can be extended to account for higher-order thermodynamic assessments and subsequently enables the design of novel FeTi-based hydrides. In addition, the assessed thermodynamic data can serve as key inputs for kinetic models and hydride microstructure simulations.

08 HYDROGEN↗

DOE OSTI2024

Designing Particle Morphologies for Materials with Solid Transport Limitations: A Case Study of Lithium and Manganese Rich Cathode Oxides

A lithium and manganese rich nickel-manganese-cobalt oxide (LMR-NMC) cathode is a promising candidate for next-generation batteries due to its high specific capacity, low cost, and low cobalt content. However, the material suffers from poor rate capability due to the diffusion limitations of lithium in the cathode particles. Understanding the material performance requires careful control of the morphology of the cathode particles, taking into account the primary and agglomerated diffusion pathways and the presence of pores, some of which could be closed from electrolyte infiltration. Here, in this study, we use a microstructure-based mathematical model combined with experimental data to understand the role of the complex cathode particle morphology in the rate performance of the material. Scanning electron microscopy images of cathodes made under different synthesis conditions, which results in different agglomerate morphologies, serve as the input into the mathematical model. The model is then compared to rate data to understand the controlling parameters. The presence of intra-agglomerate closed pores results in a large agglomerate diffusion length in comparison to the ideal condition, where the primary particles are agglomerated in an open and dispersed manner such that the entire interfacial area is available for electrochemical reaction. Smaller primary and agglomerate diffusion lengths result in better electrochemical performance. This points us toward designing the morphology of the cathode particles to compensate for the diffusion limitation of LMR-NMC while maximizing the density.

Tewari, Deepti↗

DOE OSTI2020

Radioactive Material Dynamics @ NSLS-II [Slides]

RMD @ NSLS-II helps pave the path to a DMMSC: Developing expertise in techniques and experimental methods for DMMSC science; Improving capabilities for models to become microstructurally aware; Workforce training and development; Help refine DMMSC scientific requirements; Complementary to DMMSC XFEL science (EDXD/EXAFS)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1990

U.S.-Japan Workshop on Smart/Intelligent Materials and Systems, Honolulu, HI, Mar. 19-23, 1990, Proceedings

Topics presented include the concept of intelligent materials, the molecular engineering of channel proteins, the prospects, limitations, and requirements of intelligent micro motion systems, the modeling of a shape memory integrated actuator for vibration control of large space structures, and intelligent materials for future electronics. Also presented are the slewing of an active structure, the health monitoring of control system components, the numerical modeling of the microstructure of crystals with symmetry-related variants, and the intelligent material system concept.

Ahmad, Iqbal↗

NASA NTRS2011

Thermal Cycling and Isothermal Deformation Response of Polycrystalline NiTi: Simulations vs. Experiment

A recent microstructure-based FEM model that couples crystal-based plasticity, the B2<-> MB190 phase transformation and anisotropic elasticity at the grain scale is calibrated to recent data for polycrystalline NiTi (49.9 at.% Ni). Inputs include anisotropic elastic properties, texture and differential scanning calorimetry data, as well as a subset of recent isothermal deformation and load-biased thermal cycling data. The model is assessed against additional experimental data. Several experimental trends are captured - in particular, the transformation strain during thermal cycling monotonically increases and reaches a peak with increasing bias stress. This is achieved, in part, by modifying the martensite hardening matrix proposed by Patoor et al. [Patoor E, Eberhardt A, Berveiller M. J Phys IV 1996;6:277]. Some experimental trends are underestimated - in particular, the ratcheting of macrostrain during thermal cycling. This may reflect a model limitation that transformation-plasticity coupling is captured on a coarse (grain) scale but not on a fine (martensitic plate) scale.

Manchiraju, Sivom↗

NASA NTRS2012

Multiscale Modeling of Ultra High Temperature Ceramics (UHTC) ZrB2 and HfB2: Application to Lattice Thermal Conductivity

We are developing a multiscale framework in computational modeling for the ultra high temperature ceramics (UHTC) ZrB2 and HfB2. These materials are characterized by high melting point, good strength, and reasonable oxidation resistance. They are candidate materials for a number of applications in extreme environments including sharp leading edges of hypersonic aircraft. In particular, we used a combination of ab initio methods, atomistic simulations and continuum computations to obtain insights into fundamental properties of these materials. Ab initio methods were used to compute basic structural, mechanical and thermal properties. From these results, a database was constructed to fit a Tersoff style interatomic potential suitable for atomistic simulations. These potentials were used to evaluate the lattice thermal conductivity of single crystals and the thermal resistance of simple grain boundaries. Finite element method (FEM) computations using atomistic results as inputs were performed with meshes constructed on SEM images thereby modeling the realistic microstructure. These continuum computations showed the reduction in thermal conductivity due to the grain boundary network.

Lawson, John W.↗

NASA NTRS2012

Multiscale Modeling of UHTC: Thermal Conductivity

Lawson, John W.↗

NASA NTRS2012

ISS-Experiments of Columnar-to-Equiaxed Transition in Solidification Processing

The main topic of the research project CETSOL in the framework of the Microgravity Application Promotion (MAP) programme of the European Space Agency (ESA) is the investigation of the transition from columnar to equiaxed grain growth during solidification. Microgravity environment allows for suppression of buoyancy-driven melt flow and for growth of equiaxed grains free of sedimentation and buoyancy effects. This contribution will present first experimental results obtained in microgravity using hypo-eutectic AlSi alloys in the Materials Science Laboratory (MSL) on-board the International Space Station (ISS). The analysis of the experiments confirms the existence of a columnar to equiaxed transition, especially in the refined alloy. Temperature evolution and grain structure analysis provide critical values for the position, the temperature gradient and the solidification velocity at the columnar to equiaxed transition. These data will be used to improve modeling of solidification microstructures and grain structure on different lengths scales.

Sturz, Laszlo↗

NASA NTRS2013

The Effect of Prior Exposures on the Notched Fatigue Behavior of Disk Superalloy ME3

Environmental attack has the potential to limit turbine disk durability, particularly in next generation engines which will run hotter; there is a need to understand better oxidation at potential service conditions and develop models that link microstructure to fatigue response. More efficient gas turbine engine designs will require higher operating temperatures. Turbine disks are regarded as critical flight safety components; a failure is a serious hazard. Low cycle fatigue is an important design criteria for turbine disks. Powder metallurgy alloys, like ME3, have led to major improvements in temperature performance through refractory additions (e.g. Mo,W) at the expense of environmental resistance (Al, Cr). Service conditions for aerospace disks can produce major cycle periods extending from minutes to hours and days with total service times exceeding 1,000 hours in aerospace applications. Some of the effects of service can be captured by extended exposures at elevated temperature prior to LCF testing. Some details of the work presented here have been published.

Sudbrack, Chantal K.↗