Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Li plating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Stabilizing magnesium plating by a low-cost inorganic surface membrane for high-voltage and high-power Mg batteries

Mg batteries with halide-free electrolytes suffer from poor stability of the Mg metal anode due to electrolyte decomposition. Here, we report a low-cost zeolite membrane supported on Mg to address this challenge. It vastly reduces the population (hence decomposition) of free diglyme at the Mg/electrolyte interface, while allowing facile transport of Mg 2+ cations through the membrane. We demonstrate dendrite-free Mg plating/stripping performance in a magnesium tetrakis(hexafluoroisopropyloxy)borate/diglyme electrolyte with a 750-fold extended lifetime (over 6,000 h) and a high coulombic efficiency of ~98%. The prototype Mo 3 S 4 cathode paired with the protected Mg anode shows 91% capacity retention over 200 cycles. Importantly, this membrane protects soluble species in a high-voltage organic polymer cathode from being reduced at the anode via shuttling, achieving a full cell with a 3.5 V cutoff voltage. This results in a high specific energy density of 320 Wh kg –1 and a power density of 1,320 W kg –1 based on cathode mass.

25 ENERGY STORAGE↗

Multiparameter Screening on SlipChip Used for Nanoliter Protein Crystallization Combining Free Interface Diffusion and Microbatch Methods

This paper describes two SlipChip-based approaches to protein crystallization: a SlipChip-based free interface diffusion (FID) method and a SlipChip-based composite method that simultaneously performs microbatch and FID crystallization methods in a single device. The FID SlipChip was designed to screen multiple reagents, each at multiple diffusion equilibration times, and was validated by screening conditions for crystallization of two proteins, enoyl-CoA hydratase from Mycobacterium tuberculosis and dihydrofolate reductase/thymidylate synthase from Babesia bovis, against 48 different reagents at five different equilibration times each, consuming 12 {micro}L of each protein for a total of 480 experiments using three SlipChips. The composite SlipChip was designed to screen multiple reagents, each at multiple mixing ratios and multiple equilibration times, and was validated by screening conditions for crystallization of two proteins, enoyl-CoA hydratase from Mycobacterium tuberculosis and dihydrofolate reductase/thymidylate synthase from Babesia bovis. To prevent cross-contamination while keeping the solution in the neck channels for FID stable, the plates of the SlipChip were etched with a pattern of nanowells. This nanopattern was used to increase the contact angle of aqueous solutions on the surface of the silanized glass. The composite SlipChip increased the number of successful crystallization conditions and identified more conditions for crystallization than separate FID and microbatch screenings. Crystallization experiments were scaled up in well plates using conditions identified during the SlipChip screenings, and X-ray diffraction data were obtained to yield the protein structure of dihydrofolate reductase/thymidylate synthase at 1.95 {angstrom} resolution. This free-interface diffusion approach provides a convenient and high-throughput method of setting up gradients in microfluidic devices and may find additional applications in cell-based assays.

59 BASIC BIOLOGICAL SCIENCES↗

Broadband asymmetric acoustic transmission by a plate with quasi-periodic surface ridges

In this paper, an acoustic system with broadband asymmetric transmission is designed and fabricated, which consists of a water-immersed aluminum plate engraved with quasi-periodically-patterned ridges on single surface. It demonstrates that when the acoustic waves are launched into the system from the structured side, they can couple into the Lamb modes in the plate efficiently and attain a high transmission; on the contrary, when the waves are incident from the opposite flat side, the coupling is weak, and the transmission is low. Superior to systems with periodic patterning, this quasi-periodically-patterned system has a broad working frequency range due to the collective contributions from the multiple diffractions specific to the structure.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Measurement of toroidal vessel eddy current during plasma disruption on J-TEXT

In this paper, we have employed a thin, printed circuit board eddy current array in order to determine the radial distribution of the azimuthal component of the eddy current density at the surface of a steel plate. The eddy current in the steel plate can be calculated by analytical methods under the simplifying assumptions that the steel plate is infinitely large and the exciting current is of uniform distribution. The measurement on the steel plate shows that this method has high spatial resolution. Then, we extended this methodology to a toroidal geometry with the objective of determining the poloidal distribution of the toroidal component of the eddy current density associated with plasma disruption in a fusion reactor called J-TEXT. The preliminary measured result is consistent with the analysis and calculation results on the J-TEXT vacuum vessel.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

High Resolution Characterization of the Precipitation Behavior of an Al-Zn-Mg-Cu alloy

The metastable particles in an Al-Zn-Mg-Cu alloy have been examined at atomic-resolution using high-angle annular dark field (HAADF) imaging. In underaged conditions, thin {eta}' plates were formed with a thickness of 7 atomic planes parallel to the {l_brace}111{r_brace}Al planes. The five inner planes of the {eta}' phase appear to be alternatively enriched in Mg and Zn, with two outer planes forming distinct Zn-rich interfacial planes. Similar Zn rich interfacial enrichment has also been identified for the {eta} phase, which is a minimum 11-planes thick structure. In rare instances, particles less than 7 planes were found indicating a very early preference for 7-layer particle formation. Throughout the aging, the plate thickness appears constant, while the plate radius increases and no particles between 7 and 11 planes were observed. Based on the HAADF contrast, our observations do not support the {eta}' models previously set forth by other authors. Clear structural similarities between {eta}' and {eta} were observed, suggesting that drawing distinctions between {eta}' and {eta} phases may not be necessary or useful.

36 MATERIALS SCIENCE↗

Heat transfer on a flat plate in continuum to rarefied hypersonic flows at Mach numbers of 19.2 and 25.4

Local heat transfer rates were measured on a flat steel plate (10 in. wide and 16 in. long) with sharp and blunt leading edges (0.001 and 0.010 in.) in the transition from the strong interaction boundary layer regime with no slip at the surface to the free molecule regime. The tests were conducted in a combustion driven hypersonic shock tunnel, with the nominal free stream Mach numbers of 19.2 and 25.4, and a reflected stagnation temperature of approximately 2340 R. The twelve heat transfer gages were made of platinum sputtered on a Pyrex backing to a thickness of approximately 350 A, insulated by a silicone dioxide film. For both Mach numbers the heat transfer data agreed reasonably well with the strong interaction prediction of Li and Nagamatsu (1953, 1955) for unit Reynolds numbers greater than approximately 100,000 and leading edge Knudsen numbers less than approximately 4. At lower density conditions the rarefied flow effects began to dominate the flow phenomena near the leading edge region of the sharp flat plate. A systematic reduction in the heat transfer rate close to the leading edge was observed for both Mach number tests as the leading edge density was reduced and the mean free path was increased.

Nagamatsu, H. T.↗

Alternative Process for Manufacturing of Thin Layers of Boron for Neutron Measurement

Due to the worldwide shortage of helium 3, Boron-lined proportional counters are developed intensively by several groups. Up to now, thin boron containing layers for neutron detectors are essentially produced by sputtering of boron carbide (B{sub 4}C). This technology provides high quality films but it is slow and expensive. Our paper describes a novel and inexpensive technology for producing boron layers. This technology is based on chemical synthesis of boron 10 nanoparticles, and on electrophoretic deposition of these particles on metallic plates, or on metallic pieces with more complex shapes. The chemical synthesis consists in: - Heating boron 10 with lithium up to 700 deg. C under inert atmosphere: an intermetallic compound, LiB, is produced; - Hydrolysing this intermetallic compound: LiB + H{sub 2}O → B + Li{sup +} + OH{sup -} + 1/2H{sub 2}, where B is under the form of nanoparticles; - Purifying the suspension of boron nanoparticles in water, from lithium hydroxide, by successive membrane filtrations; - Evaporating the purified suspension, in order to get a powder of nanoparticles. The obtained nanoparticles have size around 300 nm, with a high porosity, of about 50%. This particle size is equivalent to about 150 nm massive particles. The nanoparticles are then put into suspension in a specific solvent, in order to perform deposition on metallic surfaces, by electrophoretic method. The solvent is chosen so that it is not electrolysed even under voltages of several tens of volts. An acid is dissolved into the solvent, so that the nanoparticles are positively charged. Deposition is performed on the cathode within about 10 min. The cathode could be an aluminium plate, or a nickel coated aluminium plate. Homogeneous deposition may also be performed on complex shapes, like grids in a Multigrid detector. A large volume of pieces, can be coated with a Boron-10 film in a few hours. The thickness of the layer can be adjusted according to the required neutron detection characteristics, between 0,5 to 5 μm (equivalent to 0,25 to 2.5 massive layer). The thickness is homogenous within a ±20% range. The layer is an almost pure {sup 10}B layer (90%). The ratio of the amount of deposed boron 10 to the amount of raw boron 10 used is more than 80%. Hence, another advantage of this technique is that Boron 10 will be deposited on the cathodes only, without loss of this expensive material. 2 grids of a Multi-Grid detector have been coated with pure Boron by using this technique. The film structure has been analysed with a microscope and the detector has been tested on a monochromatic neutron beam line. Preliminary results will be shown. (authors)

36 MATERIALS SCIENCE↗

Fabrication for multilayered composite thin films by dual-channel vacuum arc deposition

A flexible dual-channel curvilinear electromagnetic filter has been designed and constructed to fabricate multilayered composite films in vacuum arc ion plating. The filter possesses two guiding channels and one mixing unit. Multilayered TiN/AlN and TiAlN composite films can be produced by controlling the frequency or interval of the two cathodes. The x-ray photoelectron spectroscopy and low-angle x-ray diffraction results reveal the periodic Ti and Al structures in the TiN/AlN films. The TiAlN films exhibit a smooth surface morphology confirming effective filtering of macroparticles by the filter. High temperature oxidation conducted at 700 deg. C for an hour indicates that the weight increment in the TiAlN films produced by the dual filter is only half of that of the TiAlN films produced without a filter, thereby showing better resistance against surface oxidation.

36 MATERIALS SCIENCE↗

Microstructure refinement and mechanical properties improvement by developing IAF on inclusions in Ti–Al complex deoxidized HSLA steel

The present study focused on microstructure refinement in Ti–Al complex deoxidized low alloy structural steel by developing IAF on inclusions. The goal was to establish more determined relation between Ti, Al in steel and the produced microstructures. In steel sample with Ti and Al contents of 0.0035% and 0.0004%, respectively, IAF was well developed by inclusions characterized by TiO{sub x}–MnO oxide cores enwrapped by (MnO–SiO{sub 2}–Al{sub 2}O{sub 3})–MnS or (MnO–SiO{sub 2})–MnS surface layers. With the rise of Ti and Al contents, IAF volume decreased greatly because of different inclusion chemistry, TiO{sub x} + MnS, TiO{sub x}–Al{sub 2}O{sub 3} or Al{sub 2}O{sub 3}, which inhibit the formation of IAF. Thermodynamic calculations were carried out for optimal Ti and Al contents in steel to target inclusions with proper chemistry for nucleating IAF. These laboratorial findings were successfully applied and reproducibly observed in pilot trials. It was indicated that low temperature impact toughness at 0 °C and − 20 °C of the produced medium plate was effectively improved despite lower Ti contents than common process, which was very meaningful in saving the cost of high Ti content steels. - Highlights: • IAF volume showed close relationship to Ti or Al contents. • To target IAF, there is no need to add too many titanium alloys. • Optimal Ti and Al were about 0.0020–0.0060% and 0.0005–0.0020%, respectively. • Impact toughness of steel plate at 0 °C and − 20 °C was successfully improved.

36 MATERIALS SCIENCE↗

Charge transfer of single laser crystallized intrinsic and phosphorus-doped Si-nanocrystals visualized by Kelvin probe force microscopy

Isolated intrinsic and phosphorus doped (P-doped) Si-nanocrystals (Si-NCs) on n- and p-Si substrates are fabricated by excimer laser crystallization techniques. The formation of Si-NCs is confirmed by atomic force microscopy (AFM) and conductive AFM measurements. Kelvin probe force microscopy (KPFM) is then carried out to visualize the trapped charges in a single Si-NC dot which derives from the charge transfer between Si-NCs and Si substrates due to their different Fermi levels. The laser crystallized P-doped Si-NCs have a similar Fermi level around the mid-gap to the intrinsic counterparts, which might be caused by the inactivated impurity atoms or the surface states-related Fermi level pinning. A clear rise of the Fermi level in P-doped Si-NCs is observed after a short time thermal annealing treatment, indicating the activation of dopants in Si-NCs. Moreover, the surface charge quantity can be estimated using a simple parallel plate capacitor model for a quantitative understanding of the KPFM results at the nanoscale.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dual band metamaterial perfect absorber based on Mie resonances

We numerically and experimentally demonstrated a polarization insensitive dual-band metamaterial perfect absorber working in wide incident angles based on the two magnetic Mie resonances of a single dielectric “atom” with simple structure. Two absorption bands with simulated absorptivity of 99% and 96%, experimental absorptivity of 97% and 94% at 8.45 and 11.97 GHz were achieved due to the simultaneous magnetic and electric resonances in dielectric “atom” and copper plate. Mie resonances of dielectric “atom” provide a simple way to design metamaterial perfect absorbers with high symmetry.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Lamp with a truncated reflector cup

A lamp assembly, and method for making same. The lamp assembly includes first and second truncated reflector cups. The lamp assembly also includes at least one base plate disposed between the first and second truncated reflector cups, and a light engine disposed on a top surface of the at least one base plate. The light engine is configured to emit light to be reflected by one of the first and second truncated reflector cups.

42 ENGINEERING↗

Novel pseudo-morphotactic synthesis and characterization of tungsten nitride nanoplates

A novel pseudo-morphotactic transformation route was developed to synthesize polycrystalline {beta}-W{sub 2}N nanoplates by thermally treating tungstate-based inorganic-organic hybrid nanobelts with a lamellar microstructure in an NH{sub 3} flow. The tungstate-based hybrid nanobelts were formed in a water-in-oil-microemulsion-like 'commercial H{sub 2}WO{sub 4} powders/n-octylamine/heptane' reaction system. The as-obtained hybrid nanobelts were thermally treated in an NH{sub 3} atmosphere at 650-800 {sup o}C for 2 h to form cubic {beta}-W{sub 2}N nanoplates. XRD, SEM, TEM, FT-IR and TG-DTA were used to characterize the precursors and their final products. The polycrystalline {beta}-W{sub 2}N nanoplates derived from hybrid nanobelts, with side lengths of several hundred nanometers, consist of small nanocrystals with an average grain size of 3.2 nm. The formation of {beta}-W{sub 2}N nanoplates involved two steps: decomposing tungstate-based hybrid nanobelts into WO{sub y} and W species and then nitridizing the active W-containing species to {beta}-W{sub 2}N nanocrystals in an NH{sub 3} flow. The platelike morphology of the {beta}-W{sub 2}N nanocrystals was inherited from the precursor of tungstate-based inorganic-organic hybrid nanobelts. -- A novel pseudo-morphotactic transformation route was developed to synthesize {beta}-W{sub 2}N nanoplates by thermally treating tungstate-based inorganic-organic hybrid nanobelts, the morphology of which was inherited to the {beta}-W{sub 2}N nanocrystals. Research highlights: {yields} We synthesize {beta}-W{sub 2}N nanoplates using inorganic-organic hybrid nanobelts as precursors. {yields} {beta}-W{sub 2}N nanoplates are formed at 650-800 {sup o}C for 2 h in an NH{sub 3} flow. {yields} {beta}-W{sub 2}N nanoplates consist of small nanocrystals. {yields} The plate-like morphology of {beta}-W{sub 2}N is inherited from its hybrid precursor. {yields} The pseudo-morphotactic transformation route is suitable for large-scale synthesis.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Low resistance bakelite RPC study for high rate working capability

This paper presents series efforts to lower resistance of bakelite electrode plate to improve the RPC capability under high rate working condition. New bakelite material with alkali metallic ion doping has been manufactured and tested. This bakelite is found unstable under large charge flux and need further investigation. A new structure of carbon-embedded bakelite RPC has been developed, which can reduce the effective resistance of electrode by a factor of 10. The prototype of the carbon-embedded chamber could function well under gamma radiation source at event rate higher than 10 kHz/cm 2 . The preliminary tests show that this kind of new structure performs as efficiently as traditional RPCs.

36 MATERIALS SCIENCE↗

Phase Stability and Kinetics of Topotactic Dual Ca 2+ –Na + Ion Electrochemistry in NaSICON NaV 2 (PO 4 ) 3

Recent reports of reversible calcium plating and stripping have rekindled interest in the development of Ca-ion batteries (CIBs) as next-generation energy storage devices. This technology has the potential to overcome the limitations of conventional Li-ion batteries, but CIBs are plagued by a paucity of suitable cathode materials. To date, NaSICON-structured NaV 2 (PO 4 ) 3 has been demonstrated as a successful cathode candidate, exhibiting reversible (de)intercalation of 0.6 mol Ca 2+ along with stable cycling performance. However, a complex multiphase mixture forms on discharge so the Ca-ion charge storage mechanism in the NaSICON framework is poorly understood. Here in this work, we report on an investigation of the structure and/or Na + /Ca 2+ environment(s) of a variety of chemically prepared NaSICON Ca x Na y V 2 (PO 4 ) 3 phases which were characterized using synchrotron XRD, SEM-EDS, 23 Na NMR, and TEM. Highly calciated CaV 2 (PO 4 ) 3 , Ca 1.5 V 2 (PO 4 ) 3 , and CaNaV 2 (PO 4 ) 3 phases can be prepared at high temperature, but -unlike Ca 0.6 NaV 2 (PO 4 ) 3 -these materials are electrochemically inactive. To better understand the fundamental factors impacting successful Ca 2+ electrochemistry in this system, DFT was employed to examine the Ca x Na y V 2 (PO 4 ) 3 phase diagram and Ca 2+ diffusion mechanism. Theoretical insights show that phase separation into Na-rich and Ca-rich phases is a reason for the capacity limitation and demonstrate that Na + ions in the host materials assist the migration of neighboring Ca 2+ ions, enabling reversible electrochemistry in Ca x Na y V 2 (PO 4 ) 3 . This investigation of fundamental principles affecting reversible Ca 2+ (de)intercalation in Ca x Na y V 2 (PO 4 ) 3 allows for the development of design principles to enable the discovery of a variety of successful cathodes for CIBs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Observations on COTR due to the Microbunching Instability in Compressed Beams

The observations of the strong enhancements of the optical transition radiation (OTR) signal observed after bunch compression of photocathode beams in the Advanced Photon Source (APS) linac chicane continue to be of interest. These effects have been attributed to a microbunching instability. Recent tests with an Oriel spectrometer with ICCD readout have extended our COTR spectral studies. In this case we used a microchannel plate image intensifier with a GaAs photocathode to explore the NIR regime out to 880 nm. We report for the first time an {approx}40% intensity modulation of {approx}25-nm period throughout the observed broadband COTR spectra for some localized spatial structures. In addition, the observation of a ring-like COTR image structure in x-y space for a mismatched beam at 355 MeV and a COTR mitigation concept is presented and discussed.

43 PARTICLE ACCELERATORS↗

Boundary Layer Stability and Transition in a Chemically Reacting Martian Atmosphere Using LASTRAC

The Thermal Protection System (TPS) is a significant portion of the mass of reentry vehicles, planetary probes, and Martian entry vehicles. Reducing this mass has benefits in terms of decreased fuel requirements and increased payload; however, due to the high risk and uncertainty, the TPS or heat shields are designed conservatively by assuming fully turbulent flow. Laminar flow results in reduced heat flux, and improved transition prediction has the potential to reduce TPS mass and uncertainty in aerothermodynamic predictions. Limited previous research exists examining the problem of transition prediction for Martian atmospheric entry, with studies available on transition on the Mars Science Laboratory TPS. Although transition was demonstrated in wind-tunnel tests, uncertainty in the transition location resulted in a TPS designed for fully turbulent flow, and therefore greater mass than required for a partially laminar condition. In this work, we extend the boundary layer stability code LASTRAC, recently modified to include chemical and thermal nonequilibrium capabilities, to a model of the Martian atmosphere. LASTRAC provides Parabolized Stability Equations (PSE) as well as Linear Stability Theory (LST) to predict the stability of a boundary layer and transition with semi-empirical e(sup N) methods. Results included in this work compare disturbance growth characteristics between air and Martian atmosphere at similar non-dimensional freestream conditions on a simple flat plate geometry. Both chemical nonequilibrium and thermochemical nonequilibrium, as well as both PSE and LST, are used.

Kline, H. L.↗