SEARCH · Engineering Papers

Results for “Landing Gear”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Parametric study of critical constraints for a canard configured medium range transport using conceptual design optimization

Constrained parameter optimization was used to perform optimal conceptual design of both canard and conventional configurations of a medium range transport. A number of design constants and design constraints were systematically varied to compare the sensitivities of canard and conventional configurations to a variety of technology assumptions. Main landing gear location and horizontal stabilizer high-lift performance were identified as critical design parameters for a statically stable, subsonic canard transport.

Arbuckle, P. D.↗

NASA NTRS1983

Safe structures for future aircraft

The failure mechanisms, design lessons, and test equipment employed by NASA in establishing the airworthiness and crashworthiness of aircraft components for commercial applications are described. The composites test programs have progressed to medium primary structures such as stabilizers and a vertical fin. The failures encountered to date have been due to the nonyielding nature of composites, which do not diffuse loads like metals, and the presence of eccentricities, irregular shapes, stiffness changes, and discontinuities that cause tension and shear. Testing to failure, which always occurred in first tests before the design loads were reached, helped identify design changes and reinforcements that produced successful products. New materials and NDE techniques are identified, together with aircraft structural design changes that offer greater protection to the passengers, fuel antimisting agents, and landing gear systems.

Mccomb, H. G., Jr.↗

NASA NTRS1985

Fuel-Conservative Descents Using A Programable Calcultor

Airborne descent algorithm used with or without time constraints. Concepts provide fuel savings by matching airplane arrival flow to airport acceptance rate through time control computations and allowing pilot to descend at his descretion from cruise altitude to designated metering fix in idle-thrust clean (landing gear up, flaps, zero, and speed brakes retracted) configuration. Also used for planning fuel-conservative descents when time is not consideration.

Knox, C. E.↗

NASA NTRS1983

Primary electric power generation systems for advanced-technology engines

The advantages of the all electric airplane are discussed. In the all electric airplane the generator is the sole source of electric power; it powers the primary and secondary flight controls, the environmentals, and the landing gear. Five candidates for all electric power systems are discussed and compared. Cost benefits of the all electric airplane are discussed.

Cronin, M. J.↗

NASA NTRS1980

Results of design studies and wind tunnel tests of high-aspect-ratio supercritical wings for an energy efficient transport

These basic characteristics of critical wings included wing area, aspect ratio, average thickness, and sweep as well as practical constraints on the planform and thickness near the wing root to allow for the landing gear. Within these constraints, a large matrix of wing designs was studied with spanwise variations in the types of airfoils and distribution of lift as well as some small planform changes. The criteria by which the five candidate wings were chosen for testing were the cruise and buffet characteristics in the transonic regime and the compatibility of the design with low speed (high-lift) requirements. Five wing-wide-body configurations were tested in the NASA Ames 11-foot transonic wind tunnel. Nacelles and pylons, flap support fairings, tail surfaces, and an outboard aileron were also tested on selected configurations.

Steckel, D. K.↗

NASA NTRS1984

Second Sailplane Project: The RP-2

Progress has been made on the design fabrication and installation of a tension carry-through linkage between the aft parts of the port and starboard wings to resist forward bending deflection on the RP-2 sailplane. In addition, towhook/release mechanisms, landing gear and wheel brake assembly, compound curved sandwich composite fuselage shells and an enclosed trailer to house and transport the complete disassembled aircraft, have all undergone various stages of design, fabrication, installation and testing.

Source record↗

NASA NTRS1985

Some effects of digital sampling on orbiter flight control system operation

An entry dynamic stability ground test of the OV102 Space Shuttle Orbiter revealed some small amplitude oscillatory output of the flight control system which could have constrained flight of the STS-1 mission. These limit-cycle-type outputs were attributed to a combination of rigid body motion of the Orbiter on its landing gear and some interesting effects of its digital flight control system. These effects included frequency aliasing and phenomena associated with digital quantitization of low amplitude sensor signals. The digital effects suggest significant improvements possible in future designs.

Murray, S. V.↗

NASA NTRS1985

Orbiter wheel and tire certification

The orbiter wheel and tire development has required a unique series of certification tests to demonstrate the ability of the hardware to meet severe performance requirements. Early tests of the main landing gear wheel using conventional slow roll testing resulted in hardware failures. This resulted in a need to conduct high velocity tests with crosswind effects for assurance that the hardware was safe for a limited number of flights. Currently, this approach and the conventional slow roll and static tests are used to certify the wheel/tire assembly for operational use.

Campbell, C. C., Jr.↗

NASA NTRS1985

Wind-Tunnel Investigation of a Full-Scale Canard-Configured General Aviation Airplane

An investigation was conducted in the Langley 30- by 60-Foot Tunnel to determine the aerodynamic characteristics of a powered, full-scale model of a general aviation airplane employing a canard. Although primary emphasis of the investigation was placed on evaluating the aerodynamic performance and the stability and control characteristics of the basic configuration, tests were also conducted to study the following effects of varying the basic configuration: effect of Reynolds number; effect of canard; effect of outboard wing leading-edge droop; effect of center-of-gravity location; effect of elevator trim; effect of landing gear; effect of lateral-directional control; effect of power; effect of fixed transition; effect of water spray; effects of canard incidence, canard airfoil section, and canard position; and effects of winglets and upper winglet size. Additional aspects of the study were to determine the boundary-layer transition characteristics of airfoil surfaces and the effect of fixing the boundary layer to be turbulent by means of a transition strip near the leading edge. The tests were conducted at Reynolds numbers from 0.60 x 10 to the 6th power to 2.25x10 to the 6th power, based on the wing mean aerodynamic chord, at angles of attack from -4.5 deg to 41.5 deg, and at angles of sideslip from -15 deg to 15 deg.

Yip, L. P.↗

NASA NTRS1985

Parametric study of a canard-configured transport using conceptual design optimization

Constrained-parameter optimization is used to perform optimal conceptual design of both canard and conventional configurations of a medium-range transport. A number of design constants and design constraints are systematically varied to compare the sensitivities of canard and conventional configurations to a variety of technology assumptions. Main-landing-gear location and canard surface high-lift performance are identified as critical design parameters for a statically stable, subsonic, canard-configured transport.

Arbuckle, P. D.↗

NASA NTRS1985

Flight investigation of stall, spin and recovery characteristics of a low-wing, single-engine, T-tail light airplane

Flight tests were performed to investigate the stall, spin, and recovery characteristics of a four-place, low-wing, single-engine, T-tail, general aviation research airplane at an aft center-of-gravity position. Most stalls resulted in roll-offs. Spins were oscillatory in roll and pitch at 43 deg angle of attack; the magnitude of the oscillations was determined by aileron position. Power, flap deflection, and landing gear position did not affect the angle of attack to the spin. Antispin rudder followed by forward wheel with ailerons neutral produced the fastest and most consistent recoveries but the initial application of recovery controls did not always stop a spin.

Stough, H. P., III↗

NASA NTRS1985

Prediction of HiMAT RPRV component interference effects at transonic speeds

Detailed surface flow field analyses of the NASA Highly Maneuverable Aircraft Technology Remotely Piloted Research Vehicle (HiMAT RPRV) are described. Computational predictions are provided by a nonlinear finite difference transonic wing-body code. Component interference effects are obtained through modifications in lifting surface twist and camber boundary conditions. Complex aircraft interactions created by wing-tip fins, landing gear, and lower surface wing actuator fairings are included. Lifting surface viscous flow effects are modeled using a two-dimensional 'strip' boundary layer method. Correlations with flight test data presented demonstrate the high degree of accuracy achieved for this realistic aircraft configuration. This methodology and approach appears to be generally applicable to other multisurface configurations.

Laiosa, J.↗

NASA NTRS1986

Locating Cracks Amid Pitting and Corrosion

Use of two fluorescent penetrants reveals cracks. New inspection technique for locating cracks in metal parts. Dual-dye technique used to inspect metal parts having surface-roughness-height ratings from 125 to 450 microinch (3.2 to 11.4 micrometer). Parts have included shot-peened machined aluminum extrusions; partially machined aluminum castings; aluminum, steel, and titanium tabular weldments; aircraft landing-gear components; chemically milled aluminum sheet and extrusions; and rough-machined aluminum and steel forgings. Also used on nonporous ceraminc parts.

Fahey, P. P.↗

NASA NTRS1985

Nondestructive ultrasonic measurement of bolt preload using the pulsed-phase locked-loop interferometer

Achieving accurate preload in threaded fasteners is an important and often critical problem which is encountered in nearly all sectors of government and industry. Conventional tensioning methods which rely on torque carry with them the disadvantage of requiring constant friction in the fastener in order to accurately correlate torque to preload. Since most of the applied torque typically overcomes friction rather than tensioning the fastener, small variations in friction can cause large variations in preload. An instrument called a pulsed phase locked loop interferometer, which was recently developed at NASA Langley, has found widespread use for measurement of stress as well as material properties. When used to measure bolt preload, this system detects changes in the fastener length and sound velocity which are independent of friction. The system is therefore capable of accurately establishing the correct change in bolt tension. This high resolution instrument has been used for precision measurement of preload in critical fasteners for numerous applications such as the space shuttle landing gear and helicopter main rotors.

Allison, S. G.↗

NASA NTRS1985

Ground resonance analysis using a substructure modeling approach

A convenient and versatile procedure for modeling and analyzing ground resonance phenomena is described and illustrated. A computer program is used which dynamically couples differential equations with nonlinear and time dependent coefficients. Each set of differential equations may represent a component such as a rotor, fuselage, landing gear, or a failed damper. Arbitrary combinations of such components may be formulated into a model of a system. When the coupled equations are formed, a procedure is executed which uses a Floquet analysis to determine the stability of the system. Illustrations of the use of the procedures along with the numerical examples are presented.

Chen, S. Y.↗

NASA NTRS1981

Longitudinal stability and control derivatives obtained from flight data of a PA-30 aircraft

In order to obtain reliable and accurate values of the stability and control derivatives, the Dryden Fligh Research Center (DFRC) developed a technique for extracting the derivatives from flight data. This technique is implemented by a set of FORTRAN computer programs that is based on a modified maximum likelihood estimator that uses the Newton-Raphson algorithm to perform the required minimization of the derivatives. Data was obtained with a PA-30, light twin-engine general aviation aircraft in zero, half, and full flap configuration in level unaccelerated flight with the landing gear retracted. The derivatives were plotted as functions of angle of attack using various graphical arrangements to show variations of wind tunnel and flight determined values at zero flap settings. Also, data was displayed to show the effects of flap deflection and thrust variation on the longitudinal stability derivatives. The angle of attack and angle of sideslip were measured. The dynamic pressure, velocity, and altitude were calculated, using a FORTRAN computer program, from the static and dynamic pressures. The control deflections of the stabilator, ailerons, and rudder also were recorded along with left throttle position, engine rpm, and manifold pressure.

Turley, D. R.↗

NASA NTRS1984

Ground resonance analysis using a substructure modeling approach

Chen, S.-Y.↗

NASA NTRS1986

Fault tolerant control laws

A systematic procedure for the synthesis of fault tolerant control laws to actuator failure has been presented. Two design methods were used to synthesize fault tolerant controllers: the conventional LQ design method and a direct feedback controller design method SANDY. The latter method is used primarily to streamline the full-state Q feedback design into a practical implementable output feedback controller structure. To achieve robustness to control actuator failure, the redundant surfaces are properly balanced according to their control effectiveness. A simple gain schedule based on the landing gear up/down logic involving only three gains was developed to handle three design flight conditions: Mach .25 and Mach .60 at 5000 ft and Mach .90 at 20,000 ft. The fault tolerant control law developed in this study provides good stability augmentation and performance for the relaxed static stability aircraft. The augmented aircraft responses are found to be invariant to the presence of a failure. Furthermore, single-loop stability margins of +6 dB in gain and +30 deg in phase were achieved along with -40 dB/decade rolloff at high frequency.

Ly, U. L.↗