Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Laboratory experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Analytical and experimental evaluations of Space Shuttle TPS tile vibration response

Analytical studies and laboratory experiments have been performed to evaluate the vibration response of the Space Shuttle Thermal Protection System (TPS) tiles due to the intense rocket generated acoustic noise during lift-off. The TPS tiles are mounted over the exterior of the Space Shuttle Orbiter structure through Strain Isolation Pads (SIP) which protect the tiles from thermal induced shear loads at their interface. The analytical predictions indicate that the response of a typical tile is governed by the structural vibration inputs through the SIP under the tile at frequencies below 250 Hz, and by the direct acoustic excitation over the exterior surface of the tile at frequencies above 250 Hz. An evaluation of the laboratory test data for this same tile, in which conditioned (partial) coherent output spectral analysis procedures were used, leads to exactly the same conclusion. The results demonstrate the power of conditioned spectral analysis procedures in identifying vibration response mechanisms when two or more of the inputs are highly correlated.

Piersol, A. G.↗

Magnetic Flux Compression Experiments Using Plasma Armatures

Magnetic flux compression reaction chambers offer considerable promise for controlling the plasma flow associated with various micronuclear/chemical pulse propulsion and power schemes, primarily because they avoid thermalization with wall structures and permit multicycle operation modes. The major physical effects of concern are the diffusion of magnetic flux into the rapidly expanding plasma cloud and the development of Rayleigh-Taylor instabilities at the plasma surface, both of which can severely degrade reactor efficiency and lead to plasma-wall impact. A physical parameter of critical importance to these underlying magnetohydrodynamic (MHD) processes is the magnetic Reynolds number (R(sub m), the value of which depends upon the product of plasma electrical conductivity and velocity. Efficient flux compression requires R(sub m) less than 1, and a thorough understanding of MHD phenomena at high magnetic Reynolds numbers is essential to the reliable design and operation of practical reactors. As a means of improving this understanding, a simplified laboratory experiment has been constructed in which the plasma jet ejected from an ablative pulse plasma gun is used to investigate plasma armature interaction with magnetic fields. As a prelude to intensive study, exploratory experiments were carried out to quantify the magnetic Reynolds number characteristics of the plasma jet source. Jet velocity was deduced from time-of-flight measurements using optical probes, and electrical conductivity was measured using an inductive probing technique. Using air at 27-inHg vacuum, measured velocities approached 4.5 km/s and measured conductivities were in the range of 30 to 40 kS/m.

Turner, M. W.↗

Fluid Line Evacuation and Freezing Experiments for Digital Radiator Concept

The digital radiator technology is one of three variable heat rejection technologies being investigated for future human-rated NASA missions. The digital radiator concept is based on a mechanically pumped fluid loop with parallel tubes carrying coolant to reject heat from the radiator surface. A series of valves actuate to start and stop fluid flow to di erent combinations of tubes, in order to vary the heat rejection capability of the radiator by a factor of 10 or more. When the flow in a particular leg is stopped, the fluid temperature drops and the fluid can freeze, causing damage or preventing flow from restarting. For this reason, the liquid in a stopped leg must be partially or fully evacuated upon shutdown. One of the challenges facing fluid evacuation from closed tubes arises from the vapor generated during pumping to low pressure, which can cause pump cavitation and incomplete evacuation. Here we present a series of laboratory experiments demonstrating fluid evacuation techniques to overcome these challenges by applying heat and pumping to partial vacuum. Also presented are results from qualitative testing of the freezing characteristics of several different candidate fluids, which demonstrate significant di erences in freezing properties, and give insight to the evacuation process.

human space flight↗

The Dynamics of Disorder-Order Transition in Hard Sphere Colloidal Dispersions

The Physics of Hard Spheres Experiment (PHaSE) seeks a complete understanding of the entropically driven disorder-order transition in hard sphere colloidal dispersions. The light scattering instrument designed for flight collects Bragg and low angle light scattering in the forward direction via a CCD camera and performs conventional static and dynamic light scattering at 10-160 deg. through fiber optic cables. Here we report on the kinetics of nucleation and growth extracted from time-resolved Bragg images and measurements of the elastic modulus of crystalline phases obtained by monitoring resonant responses to sinusoidal forcing through dynamic light scattering. Preliminary analysis of the former indicates a significant difference from measurements on the ground, while the latter confirms nicely laboratory experiments with the same instrument and predictions from computer simulations.

Chaikin, Paul M.↗

Evidence for exclusively inorganic formation of magnetite in Martian meteorite ALH84001

Magnetite crystals produced by terrestrial magnetotactic bacterium MV-1 are elongated on a [111] crystallographic axis, in a so-called truncated hexa-Octahedral shape. This morphology has been proposed to constitute a biomarker (i.e., formed only in biogenic processes). A subpopulation of magnetite crystals associated with carbonate globules in Martian meteorite ALH84001 is reported to have this morphology, and the observation has been taken as evidence for biological activity on Mars. In this study, we present evidence for the exclusively inorganic origin of [111]-elongated magnetite crystals in ALH84001. We report three-dimensional(3-D) morphologies for approx.1000 magnetite crystals extracted from: (1) thermal decomposition products of Fe-rich carbonate produced by inorganic hydrothermal precipitation in laboratory experiments; (2) carbonate globules in Martian meteoriteeALH84001; and (3) cells of magnetotactic bacterial strain MV-1. The 3-D morphologies were derived by fitting 3-D shape models to two-dimensional bright-field transmission-electron microscope (TEAM) images obtained at a series of viewing angles. The view down the {110} axes closest to the [111] elongation axis of magnetite crystals ([111]x{110) not equal to 0) provides a 2-D projection that uniquely discriminates among the three [111]-elongated magnetite morphologies found in these samples: [111]-elongated truncated hexaoctahedron ([111]-THO), [111]-elongated cubo-octahedron ([111]-ECO), and [111]-elongated simple octahedron ([111]-ESO). All [111] -elongated morphologies are present in the three types of sample, but in different proportions. In the ALH84001 Martian meteorite and in our inorganic laboratory products, the most common [111]-elongated magnetite crystal morphology is [111]-ECO. In contrast, the most common morphology for magnetotactic bacterial strain MV-1 is [111]-THO. These results show that: (1) the morphology of [111]-elongated magnetite crystals associated with the carbonate globules in Martian meteorite ALH84001 is replicated by an inorganic process; and (2) the most common crystal morphology for biogenic (MV-1) magnetite is distinctly different from that in both ALH84001 and our inorganic laboratory products. Therefore, [111]-elongated magnetite crystals in ALH84001 do not constitute, as previously claimed, a robust biosignature and, in fact, an exclusively inorganic origin for the magnetite is fully consistent with our results. Furthermore, the inorganic synthesis method, i.e., the thermal decomposition of hydrothermally precipitated Fe-rich carbonate, is a process analogue for formation of the magnetite on Mars. Namely, precipitation of carbonate globules from carbonate-rich hydrothermal solutions followed at some later time by a thermal pulse, perhaps in association with meteoritic impact or volcanic processes on the Martian surface.

Golden, D. C.↗

A Comparison of Model Calculation and Measurement of Absorbed Dose for Proton Irradiation

With the increase in the amount of time spent EVA that is necessary to complete the construction and subsequent maintenance of ISS, it will become increasingly important for ground support personnel to accurately characterize the radiation exposures incurred by EVA crewmembers. Since exposure measurements cannot be taken within the organs of interest, it is necessary to estimate these exposures by calculation. To validate the methods and tools used to develop these estimates, it is necessary to model experiments performed in a controlled environment. This work is such an effort. A human phantom was outfitted with detector equipment and then placed in American EMU and Orlan-M EVA space suits. The suited phantom was irradiated at the LLUPTF with proton beams of known energies. Absorbed dose measurements were made by the spaceflight operational dosimetrist from JSC at multiple sites in the skin, eye, brain, stomach, and small intestine locations in the phantom. These exposures are then modeled using the BRYNTRN radiation transport code developed at the NASA Langley Research Center, and the CAM (computerized anatomical male) human geometry model of Billings and Yucker. Comparisons of absorbed dose calculations with measurements show excellent agreement. This suggests that there is reason to be confident in the ability of both the transport code and the human body model to estimate proton exposure in ground-based laboratory experiments.

Zapp, N.↗

Probing the structure of cometary ice

Computer simulations of bulk and vapor deposited amorphous ices are presented. The structure of the bulk low density amorphous ice is in good agreement with experiments on pressure disordered amorphous ice. Both the low density bulk ice and the vapor deposited ices exhibit strong ordering. Vapor deposition of hot (300 K) water molecules onto a cold (77 K) substrate yields less porous ices than deposition of cold (77 K) water molecules onto a cold substrate. Both vapor deposited ices are more porous than the bulk amorphous ice. The structure of bulk high density amorphous ice is only in fair agreement with experimental results. Attempts to simulate high density amorphous ice via vapor deposition were not successful. Electron diffraction results on vapor deposited amorphous ice indicate that the temperature of the nucleation of the cubic phase depends upon the amount of time between the deposition and the onset of crystallization, suggesting that freshly deposited ice layers reconstruct on time of the order of hours. The temperature dependence of the microporosity of the vapor deposited amorphous ices might affect laboratory experiments that are aimed at simulating astrophysical ices in the context of the origin of prebiotic organic material and its transport to the Earth.

Wilson, Michael A.↗

Formation of Leading-Edge Pinholes in the Space Shuttle Wings Investigated

The space shuttle wing leading edge and nose cap are composed of a carbon/carbon composite that is protected by silicon carbide. The coefficient of thermal expansion mismatch leads to cracks in the silicon carbide. The outer coating of the silicon carbide is a sodium-silicate-based glass that becomes fluid at the shuttles high reentry temperatures and fills these cracks. Small pinholes roughly 0.1 mm in diameter have been observed on these materials after 12 or more flights. These pinholes have been investigated by researchers at the NASA Johnson Space Center, Rockwell International, the Boeing Company, Lockheed Martin Corporation, and the NASA Glenn Research Center at Lewis Field to determine the possible sources and the extent of damage. A typical pinhole is illustrated in the photomicrographs. These pinholes are found primarily on the wing leading edges and not on the nose cap, which is covered when the orbiter is on the launch pad. The pinholes are generally associated with a bead of zincrich glass. Examination of the orbiter and launch structure indicates that weathering paint on the launch structure leads to deposits of zinc-containing paint flakes on the wing leading edge. These may become embedded in the crevices of the wing leading edge and form the observed zinc-rich glass. Laboratory experiments indicate that zinc oxide reacts vigorously with the glass coating on the silicon carbide. Thus, it is likely that this is the reaction that leads to pinhole formation (Christensen, S.V.: Reinforced Carbon/Carbon Pin Hole Formation Through Zinc Oxide Attack. Rockwell International Internal Letter, RDW 96 057, May 1996). Cross-sectional examination of pinholes suggests that they are enlarged thermal expansion mismatch cracks. This is illustrated in the photomicrographs. A careful microstructural analysis indicates that the pinhole walls consist of layers of zinc-containing glass. Thus, pinholes are likely formed by zinc oxide particles lodging in crevices and forming a corrosive zinc-rich glass that enlarges existing cracks. Having established the likely source of the pinholes, we next needed to model the damage. Our concern was that if a pinhole went through the silicon carbide to the carbon/carbon substrate, oxygen would have a clear path to oxidize the carbon at high temperatures. This possibility was examined with studies in a laboratory furnace. An ultrasonic drill was used to make artificial pinholes in a sample of protected carbon/carbon. After exposure, the specimens were weighed and cross-sectioned to quantify the extent of oxidation below the pinhole. The results at higher temperatures showed good agreement with a simple diffusion-control model. This model is based on the two-step oxidation of carbon to carbon monoxide and carbon dioxide. The fluxes are illustrated in the final figure. The model indicates a strong dependence on pinhole diameter. For smaller diameters and short times, the oxidation of carbon is very limited.

Jacobson, Nathan S.↗

Current Collection in a Magnetic Field

It is found that the upper-bound limit for current collection in the case of strong magnetic field from the current is close to that given by the Parker-Murphy formula. This conclusion is consistent with the results obtained in laboratory experiments. This limit weakly depends on the shape of the wire. The adiabatic limit in this case will be easily surpassed due to strong magnetic field gradients near the separatrix. The calculations can be done using the kinetic equation in the drift approximation. Analytical results are obtained for the region where the Earth's magnetic field is dominant. The current collection can be calculated (neglecting scattering) using a particle simulation code. Dr. Singh has agreed to collaborate, allowing the use of his particle code. The code can be adapted for the case when the current magnetic field is strong. The needed dm for these modifications is 3-4 months. The analytical description and essential part of the program is prepared for the calculation of the current in the region where the adiabatic description can be used. This was completed with the collaboration of Drs. Khazanov and Liemohn. A scheme of measuring the end body position is also proposed. The scheme was discussed in the laboratory (with Dr. Stone) and it was concluded that it can be proposed for engineering analysis.

Krivorutsky, E. N.↗

Rust transformation/rust compatible primers

Proper surface preparation has been the key to obtain good performance by a surface coating. The major obstacle in preparing a corroded or rusted surface is the complete removal of the contaminants and the corrosion products. Sandblasting has been traditionally used to remove the corrosion products before painting. However, sandblasting can be expensive, may be prohibited by local health regulations and is not applicable in every situation. To get around these obstacles, Industry developed rust converters/rust transformers and rust compatible primers (high solids epoxies). The potential use of these products for military equipment led personnel of the Belvoir Research, Development and Engineering Center (BRDEC) to evaluate the commercially available rust transformers and rust compatible primers. Prior laboratory experience with commercially available rust converters, as well as field studies in Hawaii and Puerto Rico, revealed poor performance, several inherent limitations, and lack of reliability. It was obvious from our studies that the performance of rust converting products was more dependent on the amount and type of rust present, as well as the degree of permeability of the coating, than on the product's ability to form an organometallic complex with the rust. Based on these results, it was decided that the Military should develop their own rust converter formulation and specification. The compound described in the specification is for use on a rusted surface before the application of an organic coating (bituminous compounds, primer or topcoat). These coatings should end the need for sandblasting or the removing of the adherent corrosion products. They also will prepare the surface for the application of the organic coating. Several commercially available rust compatible primers (RCP) were also tested using corroded surfaces. All of the evaluated RCP failed our laboratory tests for primers.

Emeric, Dario A.↗

Observations of nonlinear interactions in directionally spread shoaling surface gravity waves

Shoaling wave fields generated in laboratory experiments were analyzed to determine the sensitivity of nonlinear interactions to the directional distributions of incident waves. Peaks in the directional spectra observed in shallow water were consistent with near resonating, quadratic interactions between two primary waves transferring energy to a third wave with the sum frequency and vector sum wavenumber of the primary waves. Directionally colinear waves forced a higher-frequency wave propagating in the same direction as the primary waves, while directionally spread (i.e., noncolinear) primary waves forced a higher-frequency wave that propagated in a direction between those of the interacting primary waves. Deepwater wave fields with similar frequency spectra but different directional spectra evolved to different shallow-water directional spectra, yet their shallow-water frequency spectra were remarkably similar. This result suggests that the shape of the directional spectrum of the incident wave field has only a small effect on the magnitudes of nonlinear energy transfer during shoaling. The principal effect of directionality in the incident wave field is on the directions, not the amplitudes, of the nonlinearly generated waves. The laboratory data demonstrate clearly the importance of triad interactions between noncolinear and colinear shoaling waves.

Elgar, Steve↗

Direct numerical simulations of stably-stratified sheared turbulence: Implications for oceanic mixing

Direct numerical simulations of the time evolution of homogeneous stably stratified turbulent shear flows have been performed for several Richardson numbers Ri and Reynolds numbers R(sub lambda) in earlier works. The results show excellent agreement with length scale models developed from laboratory experiments to characterize oceanic turbulence. When the Richardson number Ri is less than the stationary value Ri(sub s), the turbulence intensity grows at all scales, and the growth rate appears to be a function of Ri. The size of the vertical density inversions also increases. On the other hand, when Ri is greater than or equal to Ri(sub s) the largest turbulent eddies become vertically constrained by buoyancy when the Ellison (turbulence) scale L(sub E) and the Ozmidov (buoyancy) scale L(sub O) are equal. At this point, the mixing efficiency is maximal and corresponds to a flux Richardson number R(sub f) = 0.20. The vertical mass flux becomes counter-gradient when epsilon = 19(nu)N(exp 2) and vertical density overturns are suppressed in less than half a Brunt-Vaisala period. The results of the simulations were also recast in terms of the Hydrodynamic Phase Diagram introduced in fossil turbulence models. The so-called point of fossilization occurs when epsilon = 4DCN(exp 2); Gibson proposed 13DCN(exp 2). This value is in agreement with indirect laboratory observations and field observations. Finally, the validity of the steady-state models to estimate vertical eddy diffusivities in the oceanic thermocline is discussed.

Itsweire, E. C.↗

Space Weathering of Lunar Rocks and Regolith Grains

The exposed surfaces of lunar soil grains and lunar rocks become modified and coated over time with a thin rind of material (patina) through complex interactions with the space environment. These interactions encompass many processes including micrometeorite impacts, vapor and melt deposition, and solar wind implantation/sputtering effects that collectively are referred to as "space weathering". Studies of space weathering effects in lunar soils and rocks provide important clues to understanding the origin and evolution of the lunar regolith as well as aiding in the interpretation of global chemical and mineralogical datasets obtained by remote-sensing missions. The interpretation of reflectance spectra obtained by these missions is complicated because the patina coatings obscure the underlying rock mineralogy and compositions. Much of our understanding of these processes and products comes from decades of work on remote-sensing observations of the Moon, the analysis of lunar samples, and laboratory experiments. Space weathering effects collectively result in a reddened continuum slope, lowered albedo, and attenuated absorption features in reflectance spectra of lunar soils as compared to finely comminuted rocks from the same Apollo sites. Space weathering effects are largely surface-correlated, concentrated in the fine size fractions, and occur as amorphous rims on individual soil grains. Rims on lunar soil grains are highly complex and span the range between erosional surfaces modified by solar wind irradiation to depositional surfaces modified by the condensation of sputtered ions and impact-generated vapors. The optical effects of space weathering effects are directly linked to the production of nanophase Fe metal in lunar materials]. The size of distribution of nanophase inclusions in the rims directly affect optical properties given that large Fe(sup o) grains (approx 10 nm and larger) darken the sample (lower albedo) while the tiny Fe(sup o) grains (<5nm) are the primary agent in spectral "reddening". More recent work has focused on the nature and abundance of OH/H2O in the lunar regolith using orbital data and samples analyses. Advances in sample preparation techniques have made possible detailed analyses of patina-coated rock surfaces. Major advances are occurring in quantifying the rates and efficiency of space weathering processes through laboratory experimentation.

Keller, L. P.↗

Dust on Mars: An Aeolian Threat to Human Exploration?

The NASA HEDS Program is duly concerned for human explorers regarding the potential hazard posed by the ubiquitous dust mantle on Mars. To evaluate properties of dust that could be hazardous to humans, the MPS 2001 Lander payload will include the Mars Environmental Compatibility Assessment (MECA) experiment. This includes optical and atomic-force microscopy to evaluate soil grains for shape and size, wet chemistry to evaluate toxic substances, electrometry to evaluate triboelectric charging, and test-material palets to evaluate electrostatic and magnetic adhesion, and the hardness/abrasiveness of soil grains; these experimental subcomponents are delivered samples by the camera-equipped robotic arm of the lander which will acquire material from depths of 0.5 to 1.0 m in the soil. Data returned by MECA will be of value to both the BEDS and planetary/astrobiology communities. Dust poses a threat to human exploration because the martian system does not hydrologically or chemically remove fine particles that are being continuously generated by thermal, aeolian, and colluvial weathering, and by volcanism and impact over billions of years. The dust is extremely fine-grained, in copious quantities, ubiquitous in distribution, continually mobile, and a source of poorly-grounded static charges -- a suite of characteristics posing a particulate and electrical threat to explorers and their equipment. Dust is mobilized on global and regional scales, but probably also unpredictably and violently at local scales by dust devils. The latter might be expected in great abundance owing to near surface atmospheric instability (dust devils were detected by Pathfinder during its brief lifetime). Preliminary laboratory experiments suggest that space-suit materials subjected to windblown dust may acquire a uniform, highly adhesive dust layer that is also highly cohesive laterally owing to electrostatic forces. This layer will obscure visibility through the helmet visor, penetrate joints and fabrics, change the thermal properties of the suit, and possibly affect electronic/electrical suit functions. It is paramount that future missions address the issue of interparticle forces, and in particular, the role played by ionizing radiation in affecting these forces on Mars.

Marshall, J.↗

Dust on Mars: An Aeolian Threat to Human Exploration?

The NASA HEDS Program is duly concerned for human explorers regarding the potential hazard posed by the ubiquitous dust mantle on Mars. To evaluate properties of dust that could be hazardous to humans, the NMS 2001 Lander payload will include the Mars Environmental Compatibility Assessment (MECA) experiment. This includes optical and atomic-force microscopy to evaluate soil grains for shape and size, wet chemistry to evaluate toxic substances, electrometry to evaluate triboelectric charging, and test-material palets to evaluate electrostatic and magnetic adhesion, and the hardness/abrasiveness of soil grains; these experimental subcomponents are delivered samples by the camera-equipped robotic arm of the lander which will acquire material from depths of 0.5 to 1.0 m in the soil. Data returned by MECA will be of value to both the hEDS and planetary/astrobiology communities. Dust poses a threat to human exploration because the martian system does not hydrologically or chemically remove fine particles that are being continuously generated by thermal, aeolian, and colluvial weathering, and by volcanism and impact over billions of years. The dust is extremely fine-grained, in copious quantities, ubiquitous in distribution, continually mobile, and a source of poorly-grounded static charges -- a suite of characteristics posing a particulate and electrical threat to explorers and their equipment. Dust is mobilized on global and regional scales, but probably also unpredictably and violently at local scales by dust devils. The latter might be expected in great abundance owing to near surface atmospheric instability (dust devils were detected by Pathfinder during its brief lifetime). Preliminary laboratory experiments suggest that space-suit materials subjected to windblown dust may acquire a uniform, highly adhesive dust layer that is also highly cohesive laterally owing to electrostatic forces. This layer will obscure visibility through the helmet visor, penetrate joints and fabrics, change the thermal properties of the suit, and possibly affect electronic/electrical suit functions. It is paramount that future missions address the issue of interparticle forces, and in particular, the role played by ionizing radiation in affecting these forces on Mars.

Marshall, J.↗

Human-Robot Interaction

Human-robot interaction (HRI) is a discipline investigating the factors affecting the interactions between humans and robots. It is important to evaluate how the design of interfaces affect the human's ability to perform tasks effectively and efficiently when working with a robot. By understanding the effects of interface design on human performance, workload, and situation awareness, interfaces can be developed to appropriately support the human in performing tasks with minimal errors and with appropriate interaction time and effort. Thus, the results of research on human-robot interfaces have direct implications for the design of robotic systems. For efficient and effective remote navigation of a rover, a human operator needs to be aware of the robot's environment. However, during teleoperation, operators may get information about the environment only through a robot's front-mounted camera causing a keyhole effect. The keyhole effect reduces situation awareness which may manifest in navigation issues such as higher number of collisions, missing critical aspects of the environment, or reduced speed. One way to compensate for the keyhole effect and the ambiguities operators experience when they teleoperate a robot is adding multiple cameras and including the robot chassis in the camera view. Augmented reality, such as overlays, can also enhance the way a person sees objects in the environment or in camera views by making them more visible. Scenes can be augmented with integrated telemetry, procedures, or map information. Furthermore, the addition of an exocentric (i.e., third-person) field of view from a camera placed in the robot's environment may provide operators with the additional information needed to gain spatial awareness of the robot. Two research studies investigated possible mitigation approaches to address the keyhole effect: 1) combining the inclusion of the robot chassis in the camera view with augmented reality overlays, and 2) modifying the camera frame of reference. The first study investigated the effects of inclusion and exclusion of the robot chassis along with superimposing a simple arrow overlay onto the video feed of operator task performance during teleoperation of a mobile robot in a driving task. In this study, the front half of the robot chassis was made visible through the use of three cameras, two side-facing and one forward-facing. The purpose of the second study was to compare operator performance when teleoperating a robot from an egocentric-only and combined (egocentric plus exocentric camera) view. Camera view parameters that are found to be beneficial in these laboratory experiments can be implemented on NASA rovers and tested in a real-world driving and navigation scenario on-site at the Johnson Space Center.

Sandor, Aniko↗

Statistical Analysis of Torus and Kink Instabilities in Solar Eruptions

A recent laboratory experiment of ideal magnetohydrodynamic instabilities revealed four distinct eruption regimes readily distinguished by the torus instability (TI) and helical kink instability (KI) parameters. To establish its observational counterpart, we collected 38 solar flares (stronger than GOES-class M5 in general) that took place within 45° of disk center during 2011–2017, 26 of which are associated with a halo or partial halo coronal mass ejection (CME; i.e., ejective events), while the others are CME-less (i.e., confined events). This is a complete sample of solar events satisfying our selection criteria detailed in the paper. For each event, we calculate a decay index n of the potential strapping field above the magnetic flux rope (MFR) in and around the flaring magnetic polarity inversion line (a TI parameter) and the unsigned twist number T(sub w) of the nonlinear force-free field lines forming the same MFR (a KI parameter). We then construct an n–T(sub w) diagram to investigate how the eruptiveness depends on these parameters. We find that (1) T(sub w) appears to play little role in discriminating between confined and ejective events; (2) the events with n ≳ 0.8 are all ejective, and all confined events have n ≲ 0.8. However, n ≳ 0.8 is not a necessary condition for eruption because some events with n ≲ 0.8 also erupted. In addition, we investigate the MFR’s geometrical parameters, apex height, and distance between footpoints, as a possible factors for the eruptiveness. We briefly discuss the difference of the present result for solar eruptions with that of the laboratory result in terms of the role played by magnetic reconnection.

Solar activity↗

The command system malfunction of the telstar satellite

Loss of the command function of the Telstar satellite first occurred on Novemb 4, 1962. There had been earlier indications of degraded performance. Facts are presented which led to the conclusion that the malfunction of the command system was due to surface damage to certain transistors in the redundant command decoders by the enhanced radiation in the inner Van Allen belt. Correction steps have included laboratory experiments to gain a better understanding of the cause of failure, the use of continuous normal commands, commands transmitted from Johannesburg, South Africa, and specially modified commands to circumvent failure of the more vulnerable transistors. The operations which aided in the gradual rejuvenation of both command decoders are described. Also covered are the subsequent reappearance of the command system malfunction on February 21, 1963, and its correlation with the variation of the average radiation intensity seen by the satellite.

COMMAND SYSTEM↗