Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IMPLANTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Impact of ion-implantation-induced band gap engineering on the temperature-dependent photoluminescence properties of InAs/InP quantum dashes

We report on the effects of the As/P intermixing induced by phosphorus ion implantation in InAs/InP quantum dashes (QDas) on their photoluminescence (PL) properties. For nonintermixed QDas, usual temperature-dependent PL properties characterized by a monotonic redshift in the emission band and a continual broadening of the PL linewidth as the temperature increases, are observed. For intermediate ion implantation doses, the inhomogeneous intermixing enhances the QDas size dispersion and the enlarged distribution of carrier confining potential depths strongly affects the temperature-dependent PL properties below 180 K. An important redshift in the PL emission band occurs between 10 and 180 K which is explained by a redistribution of carriers among the different intermixed QDas of the ensemble. For higher implantation doses, the homogeneous intermixing reduces the broadening of the localized QDas state distribution and the measured linewidth temperature behavior matches that of the nonintermixed QDas. An anomalous temperature-dependent emission energy behavior has been observed for extremely high implantation doses, which is interpreted by a possible QDas dissolution.

36 MATERIALS SCIENCE↗

Fabrication of surface textures by ion implantation for antireflection of silicon crystals

We report on a method based on ion implantation and thermal annealing to fabricate silicon surface textures for antireflection purposes. Modification to crystalline Si surfaces by hydrogen ion implantation is a well known phenomenon, but the surface structures generated by H implantation alone, typically of a low packing density and small aspect ratio, are not effective in suppressing light reflection from Si. We show that coimplantation of hydrogen and argon, combined with thermal annealing and oxidation, can result in an interesting surface morphology in Si crystals, yielding the lowest light reflectance of {approx}1% over a broad spectral range at various light incident angles. In addition, lattice damage to crystalline Si generated by ion implantation is reduced or completely removed by the annealing processes. Possible mechanisms for the formation of such observed surface textures are discussed.

36 MATERIALS SCIENCE↗

Productivity Improvement for the SHX--SEN's Single-Wafer High-Current Ion Implanter

Equipment productivity is a critical issue for device fabrication. For ion implantation, productivity is determined both by ion current at the wafer and by utilization efficiency of the ion beam. Such improvements not only result in higher fabrication efficiency but also reduce consumption of both electrical power and process gases. For high-current ion implanters, reduction of implant area is a key factor to increase efficiency. SEN has developed the SAVING system (Scanning Area Variation Implantation with Narrower Geometrical pattern) to address this opportunity. In this paper, three variations of the SAVING system are introduced along with discussion of their effects on fab productivity.

36 MATERIALS SCIENCE↗

CLARIS G2: Development of Carbon Cluster Implantation

Nissin's boron and carbon cluster ion implanter CLARIS G2 has been developed for the mass production of next generation CMOS devices. Development of boron cluster implant technique was presented at last IIT conference in 2008 [1]. In this paper, development of carbon cluster (C{sub 16}H{sub x}{sup +} and C{sub 7}H{sub x}{sup +}) implant technique is described. Carbon cluster implantation has been well productized in terms of throughput, beam quality and lifetime.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetic properties of ion implanted Ge{sub 1-x}Mn{sub x} thin films solidified through pulsed laser melting

Ge{sub 1-x}Mn{sub x} thin films with an average Mn concentration of 0.64 at. % were fabricated through Mn ion implantation into crystalline germanium-on-insulator wafers. Implantation damage was removed and crystallinity restored by pulsed laser melting from a single 30-ns 308-nm XeCl{sup +} excimer laser pulse. Resolidified films demonstrated higher Curie temperatures but smaller saturation magnetizations than those of both as-implanted films and implanted films subjected to rapid thermal annealing. These findings are attributed to the redistribution of Mn during solidification.

36 MATERIALS SCIENCE↗

Gold nanoparticle formation in diamond-like carbon using two different methods: Gold ion implantation and co-deposition of gold and carbon

We describe work in which gold nanoparticles were formed in diamond-like carbon (DLC), thereby generating a Au-DLC nanocomposite. A high-quality, hydrogen-free DLC thin film was formed by filtered vacuum arc plasma deposition, into which gold nanoparticles were introduced using two different methods. The first method was gold ion implantation into the DLC film at a number of decreasing ion energies, distributing the gold over a controllable depth range within the DLC. The second method was co-deposition of gold and carbon, using two separate vacuum arc plasma guns with suitably interleaved repetitive pulsing. Transmission electron microscope images show that the size of the gold nanoparticles obtained by ion implantation is 3-5 nm. For the Au-DLC composite obtained by co-deposition, there were two different nanoparticle sizes, most about 2 nm with some 6-7 nm. Raman spectroscopy indicates that the implanted sample contains a smaller fraction of sp{sup 3} bonding for the DLC, demonstrating that some sp{sup 3} bonds are destroyed by the gold implantation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Si film separation obtained by high energy proton implantation

High energy protons implantation in the 1-1.5 MeV range can be used to detach free-standing thin silicon films with thickness between 15 and 30 {mu}m. Recently, we showed that Si orientation has a strong effect on the layer separation threshold fluence and efficiency. While complete delamination of (111)Si films is achieved, (100)Si films separation is more challenging due to blistering phenomena or partial separation of the implanted layer. In this work, we study the fracture mechanism in (100) and (111)Si after high energy implantation in order to understand the origin of such a behavior. We notably point out that fracture precursor defects, i.e. the platelets, preferentially form on (111) planes, as a consequence of the low strain level in the damaged region in our implantation conditions. Fracture therefore propagates easily in (111)Si, while it requires higher fluence to overcome unfavorable precursors orientation and propagate in (100)Si.

36 MATERIALS SCIENCE↗

Plasma immersion ion implantation for reducing metal ion release

Plasma immersion ion implantation of Nitrogen and Oxygen on CoCrMo alloys was carried out to improve the tribological and corrosion behaviors of these biomedical alloys. In order to optimize the implantation results we were carried experiments at different temperatures. Tribocorrosion tests in bovine serum were used to measure Co, Cr and Mo releasing by using Inductively Coupled Plasma Mass Spectrometry analysis after tests. Also, X-ray Diffraction analysis were employed in order to explain any obtained difference in wear rate and corrosion tests. Wear tests reveals important decreases in rate of more than one order of magnitude for the best treatment. Moreover decreases in metal release were found for all the implanted samples, preserving the same corrosion resistance of the unimplanted samples. Finally this paper gathers an analysis, in terms of implantation parameters and achieved properties for industrial implementation of these treatments.

36 MATERIALS SCIENCE↗

Electrical characterisation and predictive simulation of defects induced by keV Si{sup +} implantation in n-type Si

In this work, we focused on the analysis of implantation-induced defects, mainly small interstitial clusters (ICs) and {l_brace} 311{r_brace} defects introduced in n-type Si after ion implantation using deep level transient spectroscopy (DLTS). Silicon ions (at 160 keV or 190 keV) of fluences ranging from (0.1-8.0) Multiplication-Sign 10{sup 13} cm{sup -2} have been implanted into n-type Si and annealed at temperatures between 500 Degree-Sign C and 800 Degree-Sign C specifically to create small ICs or {l_brace} 311{r_brace} s rod-like defects. In samples dominated by small ICs, DLTS spectra show prominent deep levels at Ec - 0.24 eV and Ec - 0.54 eV. After increasing the fluence and temperature, i.e., reducing the number of small ICs and forming {l_brace} 311{r_brace} defects, the peak Ec - 0.54 eV is still dominant while other electron traps Ec - 0.26 eV and Ec - 0.46 eV are introduced. There were no observable deep levels in reference, non-implanted samples. The identity and origin of all these traps are interpreted in conjunction with recently developed predictive defect simulation models.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of sequential tungsten and helium ion implantation on nano-indentation hardness of tungsten

To simulate neutron and helium damage in a fusion reactor first wall sequential self-ion implantation up to 13 dpa followed by helium-ion implantation up to 3000 appm was performed to produce damaged layers of {approx}2 {mu}m depth in pure tungsten. The hardness of these layers was measured using nanoindentation and was studied using transmission electron microscopy. Substantial hardness increases were seen in helium implanted regions, with smaller hardness increases in regions which had already been self-ion implanted, thus, containing pre-existing dislocation loops. This suggests that, for the same helium content, helium trapped in distributed vacancies gives stronger hardening than helium trapped in vacancies condensed into dislocation loops.

36 MATERIALS SCIENCE↗

Controlled fabrication of Si nanocrystal delta-layers in thin SiO{sub 2} layers by plasma immersion ion implantation for nonvolatile memories

Plasma Immersion Ion Implantation (PIII) is a promising alternative to beam line implantation to produce a single layer of nanocrystals (NCs) in the gate insulator of metal-oxide semiconductor devices. We report herein the fabrication of two-dimensional Si-NCs arrays in thin SiO{sub 2} films using PIII and rapid thermal annealing. The effect of plasma and implantation conditions on the structural properties of the NC layers is examined by transmission electron microscopy. A fine tuning of the NCs characteristics is possible by optimizing the oxide thickness, implantation energy, and dose. Electrical characterization revealed that the PIII-produced-Si NC structures are appealing for nonvolatile memories.

36 MATERIALS SCIENCE↗

Characteristic properties of Raman scattering and photoluminescence on ZnO crystals doped through phosphorous-ion implantation

P-doped ZnO was fabricated by means of the ion-implantation method. At the Raman measurement, the blue shift of the E{sub 2}{sup high} mode and A{sub 1}(LO) phonon of the inactive mode were observed after the P-ion implantation. It suggested to be caused by the compressive stress. Thus, Hall effect measurement indicates that the acceptor levels exists in P-doped ZnO while still maintaining n-type ZnO. From the X-ray photoelectron spectroscopy, the chemical bond formation of the P2p{sub 3/2} spectrum consisted of 2(P{sub 2}O{sub 5}) molecules. Therefore, the implanted P ions were substituted to the Zn site in ZnO. From the photoluminescence (PL) spectra, P-related PL peaks were observed in the energy ranges of 3.1 and 3.5 eV, and its origin was analyzed at P{sub Zn}-2V{sub Zn} complexes, acting as a shallow acceptor. With increasing temperatures, the neutral-acceptor bound-exciton emission, (A{sup 0}, X), shows a tendency to quench the intensity and extend the emission linewidth. From the relations of the intensity and the linewidth as a function of temperature, the broadening of linewidth was believed to the result that the vibration mode of E{sub 2}{sup high} participates in the broadening process of (A{sup 0}, X) and the change of luminescent intensity was attributed to the partial dissociation of (A{sup 0}, X). Consequently, these facts indicate that the acceptor levels existed in P-doped ZnO layer by the ion implantation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Formation and photoluminescence of GaAs{sub 1−x}N{sub x} dilute nitride achieved by N-implantation and flash lamp annealing

In this paper, we present the fabrication of dilute nitride semiconductor GaAs{sub 1−x}N{sub x} by nitrogen-ion-implantation and flash lamp annealing (FLA). N was implanted into the GaAs wafers with atomic concentration of about x{sub imp1} = 0.38% and x{sub imp2} = 0.76%. The GaAs{sub 1−x}N{sub x} layer is regrown on GaAs during FLA treatment in a solid phase epitaxy process. Room temperature near band-edge photoluminescence (PL) has been observed from the FLA treated GaAs{sub 1−x}N{sub x} samples. According to the redshift of the near band-edge PL peak, up to 80% and 44% of the implanted N atoms have been incorporated into the lattice by FLA for x{sub imp1} = 0.38% and x{sub imp2} = 0.76%, respectively. Our investigation shows that ion implantation followed by ultrashort flash lamp treatment, which allows for large scale production, exhibits a promising prospect on bandgap engineering of GaAs based semiconductors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Back-junction back-contact n-type silicon solar cell with diffused boron emitter locally blocked by implanted phosphorus

The highest energy conversion efficiencies in the field of silicon-based photovoltaics have been achieved with back-junction back-contact (BJBC) silicon solar cells by several companies and research groups. One of the most complex parts of this cell structure is the fabrication of the locally doped p- and n-type regions, both on the back side of the solar cell. In this work, we introduce a process sequence based on a synergistic use of ion implantation and furnace diffusion. This sequence enables the formation of all doped regions for a BJBC silicon solar cell in only three processing steps. We observed that implanted phosphorus can block the diffusion of boron atoms into the silicon substrate by nearly three orders of magnitude. Thus, locally implanted phosphorus can be used as an in-situ mask for a subsequent boron diffusion which simultaneously anneals the implanted phosphorus and forms the boron emitter. BJBC silicon solar cells produced with such an easy-to-fabricate process achieved conversion efficiencies of up to 21.7%. An open-circuit voltage of 674 mV and a fill factor of 80.6% prove that there is no significant recombination at the sharp transition between the highly doped emitter and the highly doped back surface field at the device level.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Design and application of ion-implanted polySi passivating contacts for interdigitated back contact c-Si solar cells

Ion-implanted passivating contacts based on poly-crystalline silicon (polySi) are enabled by tunneling oxide, optimized, and used to fabricate interdigitated back contact (IBC) solar cells. Both n-type (phosphorous doped) and p-type (boron doped) passivating contacts are fabricated by ion-implantation of intrinsic polySi layers deposited via low-pressure chemical vapor deposition and subsequently annealed. The impact of doping profile on the passivation quality of the polySi doped contacts is studied for both polarities. It was found that an excellent surface passivation could be obtained by confining as much as possible the implanted-and-activated dopants within the polySi layers. The doping profile in the polySi was controlled by modifying the polySi thickness, the energy and dose of ion-implantation, and the temperature and time of annealing. An implied open-circuit voltage of 721 mV for n-type and 692 mV for p-type passivating contacts was achieved. Besides the high passivating quality, the developed passivating contacts exhibit reasonable high conductivity (R{sub sh n-type} = 95 Ω/□ and R{sub sh p-type} = 120 Ω/□). An efficiency of 19.2% (V{sub oc} = 673 mV, J{sub sc} = 38.0 mA/cm{sup 2}, FF = 75.2%, and pseudo-FF = 83.2%) was achieved on a front-textured IBC solar cell with polySi passivating contacts as both back surface field and emitter. By improving the front-side passivation, a V{sub OC} of 696 mV was also measured.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Scanning transmission electron microscopy (STEM) study on surface modified CVD diamond/Si(111) film post implanted Fe-B and NiFe-B related to GMR properties

Nanostructure investigation on the post implantation by Fe-B and NiFe-B on CVD diamond/Si(111) film have been studied by means of STEM related to their GMR phenomena. Two samples were investigated carefully, firstly sample is post NiFe-B at E=70keV and dose= 10{sup 15} ions/cm{sup 2} (denoted as A-E3D1). Secondly, is post FeB at E=20 keV and dose= 10{sup 15} ions/cm{sup 2} (denoted as B-E1D1). Based on FPP measurement at room temperature (RT) and H{sub applied} = 8 kOe, A-E3D1 sample has MR ratio almost 80% and MR ratio in B-E1D1 sample is 45%. Based on STEM-EDX investigation, there are two aspects of how MR ratio of A-E3D1 more higher than those of B-E1D1. Firstly, surface nanostructure on the top of A-E3D1 film is more grazing than on the top of B-E1D1. Analysis with Scanning Transmission Electron Microscope (STEM) equipped with Electron Energy Loss Spectroscopy (EELS) the growth of amorphous carbon layer on top of the implanted diamond film with thickness around 100 nm and only 20 nm on the no implanted sample have observed. Boron atoms were found inside the carbon amorphous layer distributed homogenously. Secondly, oxygen content at the interface between diamond film and silicon substrate in sample A-E3D1 was lower than those in B-E1D1 sample. This condition gives the resistance value in A-E3D1 lower than value in B-E1D1. This result is close to the Raman Spectroscopy data measurement which obviously suggests changes on the Raman spectrum due to implantation related to Oxygen excitation from B-E1D1 sample.

36 MATERIALS SCIENCE↗

Silver migration and trapping in ion implanted ZnO single crystals

Potentially, group-Ib elements (Cu, Ag, and Au) incorporated on Zn sites can be used for p-type doping of ZnO, and in the present paper, we use ion implantation to introduce Ag atoms in wurtzite ZnO single crystals. Monitoring the Li behavior, being a residual impurity in the crystals, as a tracer, we demonstrate that Zn interstitials assist the Ag diffusion and lead to Ag pile-up behind the implanted region after annealing above 800 °C. At even higher temperatures, a pronounced Ag loss from the sample surface occurs and concurrently the Ag atoms exhibit a trap-limited diffusion into the crystal bulk with an activation energy of ∼2.6 eV. The dominant traps are most likely Zn vacancies and substitutional Li atoms, yielding substitutional Ag atoms. In addition, formation of an anomalous multipeak Ag distribution in the implanted near-surface region after annealing can be attributed to local implantation-induced stoichiometry disturbances leading to trapping of the Ag atoms by O and Zn vacancies in the vicinity of the surface and in the end-of-range region, respectively.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Optical and electronic properties of sub-surface conducting layers in diamond created by MeV B-implantation at elevated temperatures

Boron implantation with in-situ dynamic annealing is used to produce highly conductive sub-surface layers in type IIa (100) diamond plates for the search of a superconducting phase transition. Here, we demonstrate that high-fluence MeV ion-implantation, at elevated temperatures avoids graphitization and can be used to achieve doping densities of 6 at. %. In order to quantify the diamond crystal damage associated with implantation Raman spectroscopy was performed, demonstrating high temperature annealing recovers the lattice. Additionally, low-temperature electronic transport measurements show evidence of charge carrier densities close to the metal-insulator-transition. After electronic characterization, secondary ion mass spectrometry was performed to map out the ion profile of the implanted plates. The analysis shows close agreement with the simulated ion-profile assuming scaling factors that take into account an average change in diamond density due to device fabrication. Finally, the data show that boron diffusion is negligible during the high temperature annealing process.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗