Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HEAT repeats”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Specification of EBR-II Contact Profilometry Data

All contact profilometry data stored in FIPD was originally measured using the HFEF vertical contact profilometer, which was an electronic gauge to measure the diameter profile of an element or capsule continuously over the region of interest. The element could be rotated as it passed through the probes if the wire wrap was not to be removed and the element could be returned to reactor for further irradiation. If the wire wrap was removed, the element could be drawn vertically through the probes, rotated, and the process repeated. In this way any cladding ovality could be observed. Figure 1 shows the setup used to measure the fuel pin diameter profile. The ambient temperature during the measurement was ~21-23 ºC. The cladding temperature during the measurement is considered to be similar to the ambient temperature by assuming the fuel decay heat did not impact the cladding temperature. Two documents contain most of the important details about contact profilometry measurements. The first one is the operational manual of the contact profilometer (title: Element contact profilometer operation and maintenance, HFEF/N OMM 4326, DOC. NO. W0202-0007-SA-01). This manual provides: (1) description of the contact profilometer including the functions of each component (support stage, sensing head, control system, and calibration standards, etc.); (2) step-by-step guidance on calibrations, operations, and measurements; and (3) maintenance procedures and other details of the contact profilometer. The second document is a publicly accessible report entitled “A Fuel-element Profilometer for the HFEF.” This report describes the development of the contact profilometer, including the design requirements, features, and details of each component, as well as the acceptance tests for the built system. This document is important because it reports the uncertainties of the measurements with detailed deduction procedures. The reported uncertainties should apply to all hard-copy contact profilometry data in FIPD. Some key information about contact profilometry measurements was extracted from these two documents. Combining the information with other sources, a specification for interpretating the contact profilometry data in FIPD was established.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Design and Control of a Proof-of-Concept Active Jet Engine Intake Using Shape Memory Alloy Actuators

The design and control of a novel proof-of-concept active jet engine intake using Nickel-Titanium (Ni-Ti or Nitinol) shape memory alloy (SMA) wire actuators is used to demonstrate the potential of an adaptive intake to improve the fuel efficiency of a jet engine. The Nitinol SMA material is selected for this research due to the material's ability to generate large strains of up to 5 percent for repeated operations, a high power-to-weight ratio, electrical resistive actuation, and easy fabrication into a variety of shapes. The proof-of-concept engine intake employs an overlapping leaf design arranged in a concentric configuration. Each leaf is mounted on a supporting bar that rotates upon actuation by SMA wires electrical resistive heating. Feedback control is enabled through the use of a laser range sensor to detect the movement of a leaf and determine the radius of the intake area. Due to the hysteresis behavior inherent in SMAs, a nonlinear robust controller is used to direct the SMA wire actuation. The controller design utilizes the sliding-mode approach to compensate for the nonlinearities associated with the SMA actuator. Feedback control experiments conducted on a fabricated proof-of-concept model have demonstrated the capability to precisely control the intake area and achieve up to a 25 percent reduction in intake area. The experiments demonstrate the feasibility of engine intake area control using the proposed design.

Song, Gangbing↗

Examining the Impacts of Great Lakes Temperature Perturbations on Simulated Precipitation in the Northeastern United States

Most inland water bodies are not resolved by general circulation models, requiring that lake surface temperatures be estimated. Given the large spatial and temporal variability of the surface temperatures of the North American Great Lakes, such estimations can introduce errors when used as lower boundary conditions for dynamical downscaling. Lake surface temperatures (LSTs) influence moisture and heat fluxes, thus impacting precipitation within the immediate region and potentially in regions downwind of the lakes. For this study, the Advanced Research version of the Weather Research and Forecasting Model (WRF-ARW) was used to simulate precipitation over the six New England states during a 5-yr historical period. The model simulation was repeated with perturbed LSTs, ranging from 10°C below to 10°C above baseline values obtained from reanalysis data, to determine whether the inclusion of erroneous LST values has an impact on simulated precipitation and synoptic-scale features. Results show that simulated precipitation in New England is statistically correlated with LST perturbations, but this region falls on a wet–dry line of a larger bimodal distribution. Wetter conditions occur to the north and drier conditions occur to the south with increasing LSTs, particularly during the warm season. Additionally, the precipitation differences coincide with large-scale anomalous temperature, pressure, and moisture patterns. Care must therefore be taken to ensure reasonably accurate Great Lakes surface temperatures when simulating precipitation, especially in southeastern Canada, Maine, and the mid-Atlantic region.

54 ENVIRONMENTAL SCIENCES↗

Low temperature annealing and cathodoluminescence studies of type 1 chondrule compositions

Preliminary results indicate that the yellow luminescing mesostases in type I chondrules can be altered by the effects of the low level thermal metamorphism. Although heat alone was insufficient to alter the CL, reheating for geologically relevant periods could have the same results as we obtained in a second series of experiments with water present. It is known that both water and solutions of sodium metasilicate greatly accelerate the devitrification of glasses. The results of the experiments that will be repeated should further clarify how the CL changes with increased thermal alteration.

Dehart, John M.↗

Lifetime Reliability Prediction of Ceramic Structures Under Transient Thermomechanical Loads

An analytical methodology is developed to predict the probability of survival (reliability) of ceramic components subjected to harsh thermomechanical loads that can vary with time (transient reliability analysis). This capability enables more accurate prediction of ceramic component integrity against fracture in situations such as turbine startup and shutdown, operational vibrations, atmospheric reentry, or other rapid heating or cooling situations (thermal shock). The transient reliability analysis methodology developed herein incorporates the following features: fast-fracture transient analysis (reliability analysis without slow crack growth, SCG); transient analysis with SCG (reliability analysis with time-dependent damage due to SCG); a computationally efficient algorithm to compute the reliability for components subjected to repeated transient loading (block loading); cyclic fatigue modeling using a combined SCG and Walker fatigue law; proof testing for transient loads; and Weibull and fatigue parameters that are allowed to vary with temperature or time. Component-to-component variation in strength (stochastic strength response) is accounted for with the Weibull distribution, and either the principle of independent action or the Batdorf theory is used to predict the effect of multiaxial stresses on reliability. The reliability analysis can be performed either as a function of the component surface (for surface-distributed flaws) or component volume (for volume-distributed flaws). The transient reliability analysis capability has been added to the NASA CARES/ Life (Ceramic Analysis and Reliability Evaluation of Structures/Life) code. CARES/Life was also updated to interface with commercially available finite element analysis software, such as ANSYS, when used to model the effects of transient load histories. Examples are provided to demonstrate the features of the methodology as implemented in the CARES/Life program.

Nemeth, Noel N.↗

Basaltic Magmatism: The Dominant Factor in the Petrologic and Tectonic Evolution of the Earth

Silicate bodies such as the Moon, Mars, probably Mercury, and possibly Venus, appear to have evolved in three main stages: a first (felsic) differentiation, a late heavy bombardment, and a second (basaltic) differentiation. It has been proposed that the Earth underwent a similar sequence. This paper argues that the second differentiation, basaltic magmatism, has dominated the petrologic and tectonic evolution of the Earth for four billion years. A global andesitic crust, formed during and after accretion of the planet, was disrupted by major impacts that triggered mantle upwelling and sea-floor spreading about 4 billion years ago. The oceanic crust collectively has since been formed by basaltic volcanism, from spreading centers and mantle plumes. However, the continental crust has also been greatly affected. Basaltic underplating has promoted anatexis and diapiric intrusion of granitoids in granite-greenstone terrains, as well as providing heat for regional metamorphism. Basaltic intrusions, such as the Nipissing diabase of the Sudbury area, have added to the thickness of continental crust. Satellite magnetic surveys suggest that there are more such basaltic intrusions than previously realized; examples include the Bangui anomaly of central Africa and the Kentucky anomaly. Basaltic overplating from mafic dike swarms has repeatedly flooded continents; had it not been for erosion, they would be covered with basalt as Venus is today. The tectonic effects of basaltic volcanism on continents have only recently been realized. The World Stress Map project has discovered that continents are under horizontal compressive stress, caused by push from mid-ocean ridges, i.e., by basaltic volcanism. The stress fields are generally uniform over large intraplate areas, and could contribute to intraplate tectonism. Seafloor spreading has demonstrably been effective for at least 200 million years, and ridge push thus a contributor to tectonic activity for that long. Collectively, the petrologic and tectonic evolution of the Earth has been dominated for about 4 billion years by the 'second differentiation,' i.e., by basaltic magmatism.

Lowman, Paul D., Jr.↗

High-Resolution Inspection of the Space Shuttle External Tank Spray-on-Foam Insulation (SOFI) using Focused Millimeter Waves at D-Band (150 GHz)

Space Shuttle Columbia's catastrophic failure has been attributed to a piece of spray-on-foam insulation (SOFI) that was dislodged from the external tank and struck the leading edge of the left wing. A piece of SOFI was also dislodged in the recent Space Shuttle Discovery's flight. Clearly, there is a great and urgent need to inspect the external tank SOFI and other similar insulating structures (including the acreage heat tile) in a reliable and robust fashion. In the past two years, millimeter wave nondestructive testing methods, using both real and synthetic focusing techniques, have shown great potential for this purpose. Recently obtained real-focused images from several different and complex SOFI panels have demonstrated the utility of these methods as being viable, robust, repeatable, simple, portable and effective. D-band frequency range which covers a frequency spectrum of 110- 170 GHz is well-suited for this purpose given the nature of the foam which causes significant scattering at much higher frequencies. This paper presents the results of using continuous-wave (CW) reflectometry conducted on several typical and complex SOFI panes at 150 GHz.

Kharkovsky, S.↗

FENIX: Towards a Fully Integrated Multiphysics Framework for Plasma Facing Component Modeling

Computational tools have a crucial role to play in accelerating the deployment of fusion as a clean, reliable, abundant, and sustainable energy source. Multiphysics, high-fidelity simulation capabilities can help model, study, and predict intricate interactions between materials performance, plasma exposure, neutron irradiation, and engineering processes. As such, they can assist in the resolution of scientific and engineering challenges underpinning design, construction, and commission of fusion power plants. To address these needs, ongoing efforts are leveraging the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework and delivering new computational tools for the fusion community. These tools inherit crucial attributes from MOOSE. They are open-source, modular, integrated with nuclear industry-standard software quality assurance processes, and enable multiphysics, multi-fidelity, fully integrated, zero- to three-dimensional, and massively parallel simulations. After a short overview of these capabilities, we will present the development of Fusion ENergy Integrated multiphys-X (FENIX), a MOOSE-based application designed to enable plasma facing component design and performance evaluation. Throughout their lifetime, plasma facing components are exposed to extreme thermal loads, repeated thermal shocks, and irradiation by plasma ions, neutral particles, and high-energy neutrons. Consequently, designing a plasma facing component with acceptable lifetime degradation is extremely challenging. FENIX aims to model the multiphysics environment in which plasma facing components evolve to accelerate their design studies. To that end, FENIX couples existing MOOSE capabilities such as heat transfer, thermomechanics, and thermal hydraulics, with tritium transport via the MOOSE-based Tritium Migration Analysis Program, Version 8 (TMAP8), with neutronics via the MOOSE-based high-fidelity neutron-photon transport and fluid dynamics code Cardinal, and finally with Particle-in-Cell plasma simulation capabilities being developed in this project. In this study, we present the current FENIX capabilities and preliminary results of its application to model the Tritium Plasma Experiment set up at Idaho National Laboratory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Overview of advanced plasma-facing materials testing for Fusion Pilot Plants at DIII-D

Characterization and testing of advanced plasma-facing materials (PFMs) for Fusion Pilot Plants (FPP) is being conducted at the DIII-D National Fusion Facility through the ongoing two-year FPP Candidate Materials Thrust. Year one tested 17 novel materials utilizing the Divertor Materials Evaluation System (DiMES), with samples analyzed pre- and post-experiment via SEM, EDS, and confocal microscopy. Repeatable reference discharges were developed to ensure uniformity between experiments, including a new strike-point rastering scenario to provide more uniform heat/particle flux across DiMES during ELMing H-mode discharges. Various sample geometries and temperatures were used to achieve FPP-relevant conditions, including samples angled 10° towards the incident plasma flux and pre-heating up to 500 °C. The first exposure of liquid lithium (Li) capillary porous structures in a tokamak demonstrated uniform emission of Li vapor and suppression of Li droplets in H-mode when preheated to 350 °C. Dispersoid-strengthened W with 1 wt% TaC, TiC, and ZrC exposed to H-mode showed cracking and dispersoid ejection for all varieties except TiC, providing a clear down-selection. Ultra-high temperature ceramic materials TiB 2 and ZrB 2 showed minimal degradation under L-mode exposure. Silicon carbide (SiC) fiber composites showed arcing along edges, while CVD SiC remained pristine. Atmospheric plasma-sprayed W and SiC coatings endured H-mode exposure without macroscopic delamination; SiC exhibited granular ejection, while W showed increased outgassing. Additional W-based alloys were stress tested in H-mode, including Ni-based W heavy alloys, W f SiC f /W composites, W multi-principle element alloys, and functionally-graded W/SiC, to varying degrees of success.

DIII-D↗

Machine learning-accelerated discovery of heat-resistant polysulfates for electrostatic energy storage

The development of heat-resistant dielectric polymers that withstand intense electric fields at high temperatures is critical for electrification. Balancing thermal stability and electrical insulation, however, is exceptionally challenging as these properties are often inversely correlated. A traditional intuition-driven polymer design approach results in a slow discovery loop that limits breakthroughs. Here we present a machine learning-driven strategy to rapidly identify high-performance, heat-resistant polymers. A trustworthy feed-forward neural network is trained to predict key proxy parameters and down select polymer candidates from a library of nearly 50,000 polysulfates. The highly efficient and modular sulfur fluoride exchange click chemistry enables successful synthesis and validation of selected candidates. A polysulfate featuring a 9,9-di(naphthalene)-fluorene repeat unit exhibits excellent thermal resilience and achieves ultrahigh discharged energy density with over 90% efficiency at 200 °C. Its exceptional cycling stability underscores its promise for applications in demanding electrified environments.

Li, He↗

Effect of Hydrogen on Steady-State and Transient Combustion Instability Characteristics

This paper examines the effects of steady-state and transient hydrogen enrichment on thermoacoustic instability in a model gas turbine combustor. Combustion instability, a feedback loop between flame heat release rate oscillations and combustor acoustics, is characterized in a swirl-stabilized flame operated at a range of hydrogen–natural gas fuel blends and heat rates. Measurements of combustor chamber pressure fluctuations and CH* chemiluminescence imaging are used to characterize instability at a range of operating conditions. Steady-state tests show that both mixture heat rate and hydrogen content affect system stability. At a given heat rate, higher levels of hydrogen result in unstable combustion. As heat rate increases, instability occurs at lower concentrations of hydrogen in the fuel. Transient operation was tested in two directions—instability onset and decay—and two hydrogen-addition times—a short time of 1 ms and a longer time of 4 s. Results show that instability onset processes, through the transient addition of hydrogen, are highly repeatable regardless of the timescale of hydrogen addition. Certain instability decay processes are less repeatable, resulting in cases that do not fully transition from unstable to stable combustion despite similar changes in hydrogen fuel flow rate. Flame behavior before, during, and after the transient is characterized using high-speed CH* chemiluminescence imaging. Analysis of the high-speed images shows changes in flame stabilization and dynamics during the onset and decay processes. Finally, the results of this study can have implications for systems that experience variations in fuel composition, particularly in light of growing interest in hydrogen as a renewable fuel.

42 ENGINEERING↗

Shock shapes on blunt bodies in hypersonic-hypervelocity helium, air, and CO2 flows, and calibration results in Langley 6-inch expansion tube

Shock shape results for flat-faced cylinders, spheres, and spherically blunted cones in various test gases, along with preliminary results from a calibration study performed in the Langley 6-inch expansion tube are presented. Free-stream velocities from 5 to 7 km/sec are generated at hypersonic conditions with helium, air, and CO2, resulting in normal shock density ratios from 4 to 19. Ideal-gas shock shape predictions, in which an effective ratio of specific heats is used as input, are compared with the measured results. The effect of model diameter is examined to provide insight to the thermochemical state of the flow in the shock layer. The regime for which equilibrium exists in the shock layer for the present air and CO2 test conditions is defined. Test core flow quality, test repeatability, and comparison of measured and predicted expansion-tube flow quantities are discussed.

Miller, C. G., III↗

Spontaneous dewetting of a perfluoropolyether

Eight different production lots of a commercial perfluoropolyether (PFPE) based on hexafluoropropene oxide (HFPO) were applied to polished metal surfaces by spinning. One of the lots repeatedly dewetted from a clean 440C steel surface, forming droplets on the surface, whereas the other seven did not dewet. This dewetting phenomenon also repeatedly occurred on 2024 aluminum and 1018 steel, but not on copper or gold. Fourier transform infrared microspectroscopy (mu-FTIR) was used to determine thickness and uniformity of the PFPE films. The dewetting lot was found to dewet from 440C steel at a film thickness greater than 520 A. A portion of the dewetting lot was heated at 316 C for 12 days in the presence of oxygen and M-50 steel. This fluid did not dewet. Sequentially, samples of the dewetting lot were filtered either with an alumina or a silica cartridge which can remove polar impurities. Neither of the filtered samples dewetted from 440C steel. It was concluded that an unknown impurity, both thermally labile and polar, present at very low concentration and undetected by our analytical techniques (FTIR, proton NMR, or F-19 NMR), was responsible for the dewetting phenomenon.

Shogrin, Bradley↗

Interannual Atmospheric Variability Simulated by a Mars GCM: Impacts on the Polar Regions

It is often assumed that in the absence of year-to-year dust variations, Mars weather and climate are very repeatable, at least on decadal scales. Recent multi-annual simulations of a Mars GCM reveal however that significant interannual variations may occur with constant dust conditions. In particular, interannual variability (IAV) appears to be associated with the spectrum of atmospheric disturbances that arise due to baroclinic instability. One quantity that shows significant IAV is the poleward heat flux associated with these waves. These variations and their impacts on the polar heat balance will be examined here.

Bridger, Alison F. C.↗

A Multi-Environment Thermal Control System With Freeze-Tolerant Radiator

Future space exploration missions require advanced thermal control systems (TCS) to dissipate heat from spacecraft, rovers, or habitats operating in environments that can vary from extremely hot to extremely cold. A lightweight, reliable TCS is being developed to effectively control cabin and equipment temperatures under widely varying heat loads and ambient temperatures. The system uses freeze-tolerant radiators, which eliminate the need for a secondary circulation loop or heat pipe systems. Each radiator has a self-regulating variable thermal conductance to its ambient environment. The TCS uses a nontoxic, water-based working fluid that is compatible with existing lightweight aluminum heat exchangers. The TCS is lightweight, compact, and requires very little pumping power. The critical characteristics of the core enabling technologies were demonstrated. Functional testing with condenser tubes demonstrated the key operating characteristics required for a reliable, freeze-tolerant TCS, namely (1) self-regulating thermal conductance with short transient responses to varying thermal loads, (2) repeatable performance through freeze-thaw cycles, and (3) fast start-up from a fully frozen state. Preliminary coolant tests demonstrated that the corrosion inhibitor in the water-based coolant can reduce the corrosion rate on aluminum by an order of magnitude. Performance comparison with state-of-the-art designs shows significant mass and power saving benefits of this technology.

Chen, Weibo↗

Martian B Storm Genesis and Evolution: Initial Analysis of Thermal Datasets.

Introduction: Dust lifting on Mars likely occurs primarily as a result of the exchange of momentum between the atmosphere and the surface via saltation. During saltation, sand-sized particles are mobilized but do not enter into suspension. When these larger particles fall back to the surface, kinetic energy is transferred to smaller dust particles which are then lofted into suspension in the atmosphere. Depending on the altitude to which dust is lofted, it can have a significant effect on atmospheric temperatures. As a strong absorber and emitter in the infrared, dust can influence atmospheric heating and modify the global circulation and weather on Mars [1,2]. Although dust is present in Mars’ atmosphere throughout the year, the atmosphere is generally dustier during the second half of the year when Mars is near perihelion. Observations reveal that episodic global-scale dust storms and fairly regular regional-scale dust storms are superimposed on a well-defined and highly repeatable seasonal cycle of dust opacity and associated mid-level atmospheric temperature responses. Kass et al. (2016) used 50 Pa temperature observations from MRO/MCS to identify three highly repeatable time periods during which regional dust storms occur, and designated them the “A”, “B” and “C” storms. While “A” and “C” storms have been studied a fair amount to-date, “B” storms have not yet been investigated in detail. This study explores the generation and evolution of the annually recurring regional dust storm known as the “B” storm, which was identified and categorized by Kass et al. (2016) based on 25 km (50 Pa) temperature observations. The B storm is a southern-hemisphere (SH) phenomenon that originates at the cap edge just after perihelion and which reaches peak intensity during the SH summer solstice, Ls 270. It may originate from the cap edge storms that spawn near the edge of the seasonal CO2 cap during retreat, but the mechanisms for B storm genesis have yet to be determined definitively [1]. Methods: We will use observational data sets and a global climate model (GCM) to investigate “B” regional storms. The data analysis component will include the analysis of imagery from MGS/MOC and MRO/MARCI, and spectroscopic data sets of dust and temperatures from MGS/TES and MRO/MCS with the goal of fully characterizing the behavior of these storms. Both MGS and TES provide data well-suited for temperature analysis at 25 km. MCS measures atmospheric temperature, dust extinction, and water ice extinction at 5 km intervals from the surface to about 80 km. TES measured atmospheric temperatures, column dust and water ice opacities, and column water vapor abundances. Measurements made by TES extended from the surface to about 40 km [1]. At the 50 Pa (25 km) level, local dust events usually confined to shallower depths are effectively filtered out of the analysis leaving the regional dust events identifiable by their temperature signatures [1]. Our preliminary analysis makes use of the fact that the brightness temperature at 15 microns (T15 temperature) is a close approximation to observed temperature at 25 km. We first reproduce the zonal mean 50 Pa level temperature plots for MY 29-32 to establish a baseline for our procedures moving forward [1]. Expanding on Kass et al. (2016), we include recent MCS data from MY 33 and 34 as well. Preliminary Analysis: The daytime (3PM) T15 temperatures in Figure 1 indicate: in MY 29, a strong A storm at Ls 240, a B storm at high southern latitudes just after Ls 270, and a C storm at Ls 320; in MY 30, a B storm at Ls 270; in MY 31 & MY 32, a B storm just before Ls 270; in MY 33, a B storm at Ls 270; and in MY 34, a strong A storm in the northern hemisphere at Ls 210, and a B storm around Ls 270 although there is a data gap. For the B storms, each is indicative of lofted dust and resultant warming. The daytime temperature structure illustrates that the B storm occurs annually around Ls 270 and is confined to high southern latitudes. It reaches its peak intensity around SH summer solstice, Ls 270, consistently for all six MY assessed. Since direct solar heating is absent overnight, the nighttime T15 temperatures (Figure 2) are often useful for differentiating the heat signature of direct solar heating from the dynamical response to that heating. However, in the southern polar latitudes at perihelion the sun does not set and direct solar heating remains present throughout the night. Importantly for our study, dust lofted in the B storm experiences this direct heating day and night for the entirety of its lifetime. The B storm expands as far north as -60 latitude and decays in latitudinal extent more gradually than it grows. This feature is less obvious in the nighttime (3AM) T15 temperatures (Figure 2). The temperature signal is stronger at night for MY 30-33. The warm pool is larger in area relative to the background at night in these four cases. This more uniform warming masks the “tail” feature somewhat, such that it is barely noticeable during these years. Unfortunately, gaps in MCS data in MY 29 and 34 prevent confirmation of the tail feature during those years, however, the B storm temperature signature follows a very different pattern than that described for MY 30-33. MY 29 and 34 appear to show smaller centers of warming at night and larger centers of warming during the day. This is in opposition to that previously described for MY 30-33. Conclusions and Future Work: We will continue investigating the heat signatures of B storms by looking at the total column heating as recorded by TES. We will also look at lower altitudes for patterns that may describe the relationship between B storms and the cap edge storms that develop while the seasonal cap is retreating. In the future, we will use GCM simulations to determine the atmospheric and thermo-dynamic conditions associated with these storms.

Courtney Marylou Batterson↗

Sintered silicon nitrode recuperator fabrication

The preliminary design and a demonstration of the feasibility of fabricating submodules of an automotive Stirling engine recuperator for waste heat recovery at 370 C are described. Sinterable silicon nitride (Sialon) tubing and plates were fabricated by extrusion and hydrostatic pressing, respectively, suitable for demonstrating a potential method of constructing ceramic recuperator-type heat exchangers. These components were fired in nitrogen atmosphere to 1800 C without significant scale formation so that they can be used in the as-fired condition. A refractory glass composition (Al2O3 x 4.5 CaO.MgO x 11SiO2) was used to join and seal component parts by a brazing technique which formed strong recuperator submodules capable of withstanding repeated thermal cycling to 1370 C. The corrosion resistance of these materials to Na2SO4 + NaCl carbon mixtures was also assessed in atmospheres of air, hydrogen and CO2-N2-H2O mixtures at both 870 C and 1370 C for times to 1000 hours. No significant reaction was observed under any of these test conditions.

Gatti, A.↗

Mass transfer from a circular cylinder: Effects of flow unsteadiness and slight nonuniformities

Experiments were performed to determine the effect of periodic variations in the angle of the flow incident to a turbine blade on its leading edge heat load. To model this situation, measurements were made on a circular cylinder oscillating rotationally in a uniform steady flow. A naphthalene mass transfer technique was developed and used in the experiments and heat transfer rates are inferred from the results. The investigation consisted of two parts. In the first, a stationary cylinder was used and the transfer rate was measured for Re = 75,000 to 110,000 and turbulence levels from .34 percent to 4.9 percent. Comparisons with both theory and the results of others demonstrate that the accuracy and repeatability of the developed mass transfer technique is about + or - 2 percent, a large improvement over similar methods. In the second part identical flow conditions were used but the cylinder was oscillated. A Strouhal number range from .0071 to .1406 was covered. Comparisons of the unsteady and steady results indicate that the magnitude of the effect of oscillation is small and dependent on the incident turbulence conditions.

Marziale, M. L.↗