Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Grain Growth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Local damage in grain boundary stabilized nanocrystalline aluminum

The excess free volume in grain boundaries of pure nanocrystalline aluminum leads to the grain coarsening, which degrades their desirable mechanical properties. The preferential segregation of dopants to the grain boundaries has been proposed to enhance the stability of the nanostructure. Here, to shed light on the stabilization mechanisms, we present results from virtual mechanical tests on nanocrystalline aluminum samples with similar grain sizes but different magnesium dopant contents. The segregation of magnesium decreases the excess free volume within the grain boundaries and prohibits the nucleation and growth of intergranular cracks.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Maize ANT1 modulates vascular development, chloroplast development, photosynthesis, and plant growth

Arabidopsis AINTEGUMENTA (ANT), an AP2 transcription factor, is known to control plant growth and floral organogenesis. In this study, our transcriptome analysis and in situ hybridization assays of maize embryonic leaves suggested that maize ANT1 (ZmANT1) regulates vascular development. To better understand ANT1 functions, we determined the binding motif of ZmANT1 and then showed that ZmANT1 binds the promoters of millet SCR1, GNC, and AN3, which are key regulators of Kranz anatomy, chloroplast development, and plant growth, respectively. We generated a mutant with a single-codon deletion and two frameshift mutants of the ANT1 ortholog in the C4 millet Setaria viridis by the CRISPR/Cas9 technique. The two frameshift mutants displayed reduced photosynthesis efficiency and growth rate, smaller leaves, and lower grain yields than wild-type (WT) plants. Moreover, their leaves sporadically exhibited distorted Kranz anatomy and vein spacing. Conducting transcriptomic analysis of developing leaves in the WT and the three mutants we identified differentially expressed genes (DEGs) in the two frameshift mutant lines and found many down-regulated DEGs enriched in photosynthesis, heme, tetrapyrrole binding, and antioxidant activity. In addition, we predicted many target genes of ZmANT1 and chose 13 of them to confirm binding of ZmANT1 to their promoters. Based on the above observations, we proposed a model for ANT1 regulation of cell proliferation and leaf growth, vascular and vein development, chloroplast development, and photosynthesis through its target genes. Furthermore, our study revealed biological roles of ANT1 in several developmental processes beyond its known roles in plant growth and floral organogenesis.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Metal stack templates for suppressing secondary grains in sca1n

A metal stack for templating the growth of AlN and ScAlN films is disclosed. The metal stack comprises one, two, or three layers of metal, each of which is compatible with CMOS post-processing. The metal stack provides a template that promotes the growth of highly textured c-axis {002} AlN and ScAlN films. The metal stacks include one or more metal layers with each metal layer having either a hexagonal {002} orientation or a cubic {111} orientation. If the metal stack includes two or more metal layers, the layers can alternate between hexagonal {002} and cubic {111} orientations. The use of ScAlN results in a higher piezoelectric constant compared to that of AlN for ScAlN alloys up to approximately 44% Sc. The disclosed metal stacks resulted in ScAlN films having XRD FWHM values of less than approximately 1.1° while significantly reducing the formation of secondary grains in the ScAlN films.

Esteves, Giovanni↗
DOE OSTI2021

Direct observations and characterization of crack closure during microstructurally small fatigue crack growth via in-situ high-energy X-ray characterization

This study provides direct observation of the crack closure mechanism of a naturally occurring, tortuous, 3D microstructurally small fatigue crack (SFC) in additively manufactured Inconel 718. In-situ non-destructive characterization is performed using high-energy X-ray diffraction techniques to capture the evolution of the 3D microstructure and micromechanical response in the vicinity of the crack front. Based on the stress state of twelve grains analyzed at the crack tip, the crack closure events of the SFC front was found to be spatially heterogeneous with respect to loading progression governed by the local stress state of the grains (specifically the stress reversal from compression to tension). From this analysis, three grains that displayed different degrees of crack closure were further investigated, based on the orientation of the crack relative to the grains and the associated modality of crack growth. The stress normal to the crack plane and the associated degree of Mode I crack behavior were correlated with events of the crack opening earlier during the loading cycle. This was further corroborated by diffraction spot spreading analysis that quantified the crystallographic lattice distortion caused by the opening crack. Additionally, the detailed characterization of the opening behavior of the grains located at the crack tip and their associated states of stress elucidates the mechanism governing crack closure and will inform future modeling efforts of this phenomenon.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A mechanistic interpretation of Nelson curves for PVP failures under high temperature hydrogen attack

As an empirically established design criterion, Nelson curves that relate the service temperature and the allowable hydrogen partial pressure have been developed and utilized for more than sixty years in pressure vessels and piping (PVP) safety design. Despite a relatively clear thermodynamic understanding of the high-temperature-hydrogen-attack (HTHA) problem, the detailed fracture process on the microstructural length scales, however, remains elusive, and a quantitative assessment of the PVP lifetime under HTHA from the available creep fracture dataset is still not possible. This work develops a microstructure-informed and micromechanics-based model by incorporating a synergy between hydrogen transport and intergranular-cavity-based fracture process. Based on the available creep lifetime data of C-0.5Mo steels, we are able to calibrate material constitutive parameters, and then conduct nonlinear finite element simulations that reveal a real-time stress-induced hydrogen diffusional transport along grain boundaries, coupled with a microstructure-explicit failure process, from which Nelson curves can be computed. Such failure analyses allow us to delineate two distinct regimes on the Nelson curves, i.e., dislocation-creep-controlled or grain boundary diffusion-assisted cavity growth. More importantly, we found that a small change of the pipe thickness and applied stresses can significantly shift these lifetime curves. However, these two parameters are usually not provided in Nelson curves, thus limiting their usage in material selection and safety design. In conclusion, this discrepancy can clearly be mitigated by extensive parametric studies from our micromechanical modeling/simulation framework.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Thermal tolerance of perovskite quantum dots dependent on A-site cation and surface ligand

A detailed picture of temperature dependent behavior of Cs x FA 1-x PbI 3 perovskite quantum dots across the composition range is constructed by performing in situ optical spectroscopic and structural measurements, supported by theoretical calculations that focus on the relation between A-site chemical composition and surface ligand binding. The thermal degradation mechanism depends not only on the exact chemical composition, but also on the ligand binding energy. The thermal degradation of Cs-rich perovskite quantum dots is induced by a phase transition from black γ-phase to yellow δ-phase, while FA-rich perovskite quantum dots with higher ligand binding energy directly decompose into PbI 2 . Quantum dot growth to form large bulk size grain is observed for all Cs x FA 1-x PbI 3 perovskite quantum dots at elevated temperatures. In addition, FA-rich quantum dots possess stronger electron-longitudinal optical phonon coupling, suggesting that photogenerated excitons in FA-rich quantum dots have higher probability to be dissociated by phonon scattering compared to Cs-rich quantum dots.

14 SOLAR ENERGY↗
DOE OSTI2023

CEGANN: CRYSTAL EDGE GRAPH ATTENTION NEURAL NETWORK

SF-22-156 Machine learning (ML) models and applications in materials design and discovery typically involve the use of feature representations or descriptors followed by a learning algorithm that maps them to user desired properties of interest. Most popular mathematical formulation-based descriptors are not unique across atomic environments and suffer from transferability issues across different application domains and/or material classes. The CEGANN code provides a unified interface to facilitate material characterization across materials across multiple scales (from atomic to mesoscale) and diverse classes of materials ranging from metals oxides, non-metals, and even hierarchical materials such as zeolites and semi ordered materials such as mesophases. CEGANN implements a Graph Attention Network (GAT) type convolution architecture. The details of network architecture can be found in the paper https://doi.org/10.48550/arXiv.2207.10168. The software comes with pretrained examples and dataset for the classification of the following representative systems: (1) Structure-level representation such as space group (2) Structural dimensionality (e.g., bulk, 2D, clusters etc.) (3) Grain boundary identification (4) Nucleation and growth of a zeolite polymorph (5) Characterization of binary mesophases and their phase transitions (6) Growth of ice. The code is written in python programming language.

CHAN, HENRYT↗
DOE OSTI2022

Structural, Optical and Mechanical Properties of Nanocrystalline Molybdenum Thin Films Deposited under Variable Substrate Temperature

Molybdenum (Mo), which is one among the refractory metals, is a promising material with a wide variety of technological applications in microelectronics, optoelectronics, and energy conversion and storage. However, understanding the structure–property correlation and optimization at the nanoscale dimension is quite important to meet the requirements of the emerging nanoelectronics and nanophotonics. In this context, we focused our efforts to derive a comprehensive understanding of the nanoscale structure, phase, and electronic properties of nanocrystalline Mo films with variable microstructure and grain size. Molybdenum films were deposited under varying temperature (25–500 °C), which resulted in Mo films with variable grain size of 9–22 nm. The grazing incidence X-ray diffraction analyses indicate the (110) preferred growth behavior the Mo films, though there is a marked decrease in hardness and elastic modulus values. In particular, there is a sizable difference in maximum and minimum elastic modulus values; the elastic modulus decreased from ~460 to 260–280 GPa with increasing substrate temperature from 25–500 °C. The plasticity index and wear resistance index values show a dramatic change with substrate temperature and grain size. Additionally, the optical properties of the nanocrystalline Mo films evaluated by spectroscopic ellipsometry indicate a marked dependence on the growth temperature and grain size. This dependence on grain size variation was particularly notable for the refractive index where Mo films with lower grain size fell in a range between ~2.75–3.75 across the measured wavelength as opposed to the range of 1.5–2.5 for samples deposited at temperatures of 400–500 °C, where the grain size is relatively higher. The conductive atomic force microscopy (AFM) studies indicate a direct correlation with grain size variation and grain versus grain boundary conduction; the trend noted was improved electrical conductivity of the Mo films in correlation with increasing grain size. The combined ellipsometry and conductive AFM studies allowed us to optimize the structure–property correlation in nanocrystalline Mo films for application in electronics and optoelectronics.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In Situ Characterization of the Effect of Twin-Microstructure Interactions on {$1 0 \bar{1} 2$} Tension and {$1 0\bar {1} 1$} Contraction Twin Nucleation, Growth and Damage in Magnesium

Through in situ electron backscatter diffraction (EBSD) experiments, this paper uncovers dominant damage mechanisms in traditional magnesium alloys exhibiting deformation twinning. The findings emphasize the level of deleterious strain incompatibility induced by twin interaction with other deformation modes and microstructural defects. A double fiber obtained by plane-strain extrusion as a starting texture of AM30 magnesium alloy offered the opportunity to track deformation by EBSD in neighboring grains where some undergo profuse {$1 0\bar {1} 2$} twinning and others do not. For a tensile loading applied along extrusion transverse (ET) direction, those experiencing profuse twinning reveal a major effect of grain boundaries on non-Schmid behavior affecting twin variant selection and growth. Similarly, a neighboring grain, with its $\langle$c$\rangle$-axis oriented nearly perpendicular to tensile loading, showed an abnormally early nucleation of {$1 0\bar {1} 1$} contraction twins (2% strain) while the same {$1 0\bar {1} 1$} twin mode triggering under $\langle$c$\rangle$-axis uniaxial compression have higher value of critical resolved shear stress exceeding the values for pyramidal $\langle$c + a$\rangle$ dislocations. The difference in nucleation behavior of contraction vs. compression {$1 0\bar {1} 1$} twins is attributed to the hydrostatic stresses that promote the required atomic shuffles at the core of twinning disconnections.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Residual stress and microstructure in IN718-René41 graded superalloy fabricated by laser blown directed energy deposition

Additively printed Ni-based superalloy with a compositionally graded transition from IN718 to René41 was fabricated by laser blown-powder directed energy deposition (DED/LB-M), with the goals of meeting location-specific temperature capability and reducing component cost for hot gas path turbine components. Residual stress distribution in thin wall specimens with three sets of DED build parameters in the as-built and stress-relieved states was measured by neutron diffraction. For calculating residual stress, the calculated d0 method was found to be more appropriate as stress-free reference than using the lattice spacing measured from the stress-relief heat treated specimens. Longer dwell time (lower interpass temperature), higher energy input, smaller layer thickness resulted in a higher magnitude of tensile residual stresses at edges and compressive residual stresses at center of the specimens. The residual stress results did not show a strong dependence on graded compositions, indicating that the residual stress build-up was more geometry and process dependent. Non-destructive neutron imaging based on the attenuation coefficient qualitatively visualized the compositional variation in the bulk and showed good agreement with quantitative Electron Probe Micro-Analysis (EPMA) measurement. Grain structure, texture, and residual plastic strain along the build direction were characterized by Electron Backscatter Diffraction (EBSD). Long columnar grains with (001) preferred grain orientation were dominant along the build direction. Compositional change did not show an obvious effect on the epitaxial growth of dendrites and the continuation of the columnar grains. Residual plastic strain was relatively low in the as-built specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solid Electrolyte Bimodal Grain Structures for Improved Cycling Performance

Here, the application of solid-state electrolytes in Li batteries is hampered by the occurrence of Li-dendrite-caused short circuits. To avoid cell failure, the electrolytes can only be stressed with rather low current densities, severely restricting their performance. As grain size and pore distributions significantly affect dendrite growth in ceramic electrolytes such as Li 7 La 3 Zr 2 O 12 and its variants; here, a “detour and buffer” strategy to bring the superiority of both coarse and fine grains into play, is proposed. To validate the mechanism, a coarse/fine bimodal grain microstructure is obtained by seeding unpulverized large particles in the green body. The rearrangement of coarse grains and fine pores is fine-tuned by changing the ratio of pulverized and unpulverized powders. The optimized bimodal microstructure, obtained when the two powders are equally mixed, allows, without extra interface decoration, cycling for over 2000 h as the current density is increased from 1.0 mA·cm -2 , and gradually, up to 2.0 mA·cm -2 . The “detour and buffer” effects are confirmed from postmortem analysis. The complex grain boundaries formed by fine grains discourage the direct infiltration of Li. Simultaneously, the coarse grains further increase the tortuosity of the Li path. This study sheds light on the microstructure optimization for the polycrystalline solid-state electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2022

Understanding formation mechanisms of intermetallic compounds in dissimilar Al/steel joint processed by resistance spot welding

Here, this paper confirmed the formation mechanism of intermetallic compounds (IMCs) in Al/steel resistance spot welds with transmission electron microscopy, electron backscatter diffraction, nanoindentation and thermodynamic calculations. In particular, the formation of AlFe with BCC_B2 structure, which is not commonly seen in welds, was identified. The formation mechanism of IMCs at the high welding energy region is described as follows. Al 13 Fe 4 first nucleates from the Al side, followed by Al 5 Fe 2 growth with Fe atoms accumulating at the Al 13 Fe 4 grain boundaries. Then, Al 5 Fe 2 grains grow continuously to coarse columnar grains, and AlFe forms at the interface of Al 5 Fe 2 grains and the ferrite phase. Lastly, the needle-like Al 13 Fe 4 forms in the cooling process. At the middle welding energy region, only equiaxed Al 5 Fe 2 and small Al 13 Fe 4 grains are formed at the interface because of the lower diffusion rates of Al and Fe, hence postponing the growth of Al 5 Fe 2 and Al 13 Fe 4 . At the low welding energy region, only sporadic Al 5 Fe 2 and Al 13 Fe 4 grains are formed surrounded by the Al phase.

42 ENGINEERING↗
DOE OSTI2021

In Situ TEM Tensile Testing of Bicrystals with Tailored Misorientation Angles

Grain boundaries have complex structural features that influence strength, ductility and fracture in metals and alloys. Grain boundary misorientation angle has been identified as a key parameter that controls their mechanical behavior, but the effect of misorientation angle has been challenging to isolate in polycrystalline materials. Here, we describe the use of bicrystal Au thin films made using a rapid melt growth process to study deformation at a single grain boundary. Tensile testing is performed on bicrystals with different misorientation angles using in situ TEM, as well as on a single crystalline sample. Plastic deformation is initiated through dislocation nucleation from free surfaces. Grain boundary sliding is not observed, and failure occurs away from the grain boundary through plastic collapse in all cases. The failure behavior in these nanoscale bicrystals does not appear to depend on the misorientation angle or grain boundary energy but instead has a more complex dependence on sample surface structure and dislocation activity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Strain-Induced Growth of Twisted Bilayers during the Coalescence of Monolayer MoS 2 Crystals

Tailoring the grain boundaries (GBs) and twist angles between two-dimensional (2D) crystals are two crucial synthetic challenges to deterministically enable envisioned applications such as moiré excitons, emerging magnetism, or single-photon emission. Here, we reveal how twisted 2D bilayers can be synthesized from the collision and coalescence of two growing monolayer MoS 2 crystals during chemical vapor deposition. The twisted bilayer (TB) moiré angles are found to preserve the misorientation angle (θ) of the colliding crystals. The shapes of the TB regions are rationalized by a kink propagation model that predicts the GB formed by the coalescing crystals. Optical spectroscopy measurements reveal a θ-dependent long-range strain in crystals with stitched grain boundaries and a sharp (θ > 20°) threshold for the appearance of TBs, which relieves this strain. Reactive molecular dynamics simulations explain this strain from the continued growth of the crystals during coalescence due to the insertion of atoms at unsaturated defects along the GB, a process that self-terminates when the defects become saturated. The simulations also reproduce atomic-resolution electron microscopy observations of faceting along the GB, which is shown to arise from the growth-induced long-range strain. These facets align with the axes of the colliding crystals to provide favorable nucleation sites for second-layer growth of a TB with twist angles that preserve the misorientation angle θ. This interplay between strain generation and aligned nucleation provides a synthetic pathway for the growth of TBs with deterministic angles.

2D materials↗
DOE OSTI2020

Irradiation-Induced Extremes Create Hierarchical Face-/Body-Centered-Cubic Phases in Nanostructured High Entropy Alloys

A nanoscale hierarchical dual-phase structure is reported to form in a nanocrystalline NiFeCoCrCu high-entropy-alloy (HEA) film via ion irradiation. Under the extreme energy deposition and consequent thermal energy dissipation induced by energetic particles, a fundamentally new phenomenon is revealed, in which the original single-phase face-centered-cubic (FCC) structure partially transforms into alternating nanometer layers of a body-centered-cubic (BCC) structure. The orientation relationship follows the Nishiyama–Wasser-man relationship, that is, (011) BCC || (1¯1¯1) FCC and [100] BCC || [11¯0] FCC . Simulation results indicate that Cr, as a BCC stabilizing element, exhibits a tendency to segregate to the stacking faults (SFs). Furthermore, the high densities of SFs and twin boundaries in each nanocrystalline grain serve to accelerate the nucleation and growth of the BCC phase during irradiation. By adjusting the irradiation parameters, desired thicknesses of the FCC and BCC phases in the laminates can be achieved. Finally, this work demonstrates the controlled formation of an attractive dual-phase nanolaminate structure under ion irradiation and provides a strategy for designing new derivate structures of HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Subnanometer Scale Mapping of Hydrogen Doping in Vanadium Dioxide

Hydrogen donor doping of correlated electron systems such as vanadium dioxide (VO 2 ) profoundly modifies the ground state properties. The electrical behavior of H x VO 2 is strongly dependent on the hydrogen concentration; hence, atomic scale control of the doping process is necessary. It is however a nontrivial problem to quantitatively probe the hydrogen distribution in a solid matrix. As hydrogen transfers its sole electron to the material, the ionization mechanism is suppressed. Here in this study, a methodology mapping the doping distribution at subnanometer length scale is demonstrated across a H x VO 2 thin film focusing on the oxygen-hydrogen bonds using electron energy loss spectroscopy (EELS) coupled with first-principles EELS calculations. The hydrogen distribution was revealed to be nonuniform along the growth direction and between different VO 2 grains, calling for intricate hydrogenation mechanisms. Our study points to a powerful approach to quantitatively map dopant distribution in quantum materials relevant to energy and information science

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Structural and Electrocatalytic Studies of Pulsed Laser Deposited Epitaxial RuO 2 Thin Films

Two sets of high-quality epitaxial ruthenium oxide (RuO 2 ) thin films with different thicknesses were synthesized in situ on cost-competitive sapphire substrates by using a pulsed laser deposition technique. The first set of films, with a thickness of 40 nm and a sheet resistance of 15.7 Ω/□, was prepared using 2100 laser pulses, while the second set of films, with a thickness of 87 nm and a sheet resistance of 6.7 Ω/□, was prepared using 4800 laser pulses. All other deposition parameters were kept the same. The post-deposition structural and morphological measurements showed that both sets of films grew at the same growth rate, had the same crystallinity, similar grain boundary density, and slightly different surface roughness. The thicker RuO 2 films achieved an overpotential of 280 mV for the oxygen evolution reaction at a current density of 100 μA/cm 2 , comparable to or exceeding the performance of films grown on more expensive substrates. Comparatively, the thinner RuO 2 films, which have a significantly higher charge transfer resistance (250 Ω versus 100 Ω for thick films), display a higher overpotential of 320 mV. These results indicate that the lower electrical resistance of thicker films promotes charge transfer through the film body, leading to superior electrocatalytic properties.

charge-transfer↗
DOE OSTI2025

Scalable Solution-Processed Electrolyte Membranes with Optimized Microstructure for High-Performance Protonic Ceramic Electrochemical Cells

Proton-conducting electrochemical cells (PCECs) are promising for efficient hydrogen production, but achieving dense, uniform, thin electrolyte layers remains a key challenge, particularly for scalable fabrication. Here, we present a solution-processed deposition approach with a mechanistically optimized slurry for uniform electrolyte formation. By tailoring particle size distribution, solid loading, and solvent/additive balance, we regulated wetting behavior and evaporation kinetics of the electrolyte slurry to promote homogeneous electrolyte particle packing. These features facilitate tight grain boundary contact and early stage neck growth during sintering, eliminating residual porosity, and improving mechanical integrity. The resulting ∼15 μm thick electrolyte shows high density, strong electrode adhesion, and stable interfaces outperforming the previously reported spray-based fabricated electrolyte by about 31% at 600 °C in FC mode. Single cells deliver 0.962 W cm –2 at 600 °C in fuel cell mode and 1.31 A cm –2 at 1.3 V in electrolysis mode, maintaining robust performance over 100 h with negligible degradation (≤0.02% h –1 ) in each mode. Scale-up to 2.5 cm diameter substrates confirmed reproducible densification and geometric stability. This work demonstrates a cost-effective, scalable route where control over particle-fluid interactions and drying dynamics enables a superior electrolyte microstructure and high PCEC performance.

dense microstructure↗