Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Rod Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Investigating grid-to-rod fretting wear of nuclear fuel claddings using a unique autoclave fretting rig

Fuel rods in a pressurized water nuclear reactor (PWR) experience coolant flow-induced relative motion against the grid support features, a phenomenon called grid-to-rod fretting (GTRF), which may cause progressive fretting wear damage. Wear-through of the cladding on fuel rods will leak the radioactive fuel into the coolant loop to significantly increase the radiation level in PWR primary loop and often trigger expensive Post Irradiation Examination. In this work, a unique autoclave fretting test rig was designed and fabricated to allow studying GTRF using actual cladding and grid materials. Water temperature was up to 220 °C, which was designed to mimic the environment in an industry full-assembly reactor core simulator. The contact load (0.1–1 N), oscillation frequency (20–30 Hz) and stroke (50–150 µm), and work rate (1–3 mW) were defined based on simulations of GTRF in an actual reactor. Using this autoclave GTRF rig, tests were conducted to learn the effect of water temperature and to investigate the wear behavior of different cladding-grid material combinations currently used in actual PWRs, including Zr alloy claddings without and with pre-oxidation against Zr alloy and Inconel grids. Higher water temperature evidently increased the cladding wear, and pre-oxidation of the Zr alloy and/or using the Inconel grid effectively reduced the wear rate. In conclusion, results were correlated with the data of a full-size industry reactor core simulator in terms of both wear rate and wear scar morphology.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Ultra-High Temperature Steam Corrosion of Complex Silicates for Nuclear Applications: A Computational Study

Stability of materials under extreme conditions is an important issue for safety of nuclear reactors. Presently, silicon carbide (SiC) is being studied as a cladding material candidate for fuel rods in boiling-water and pressurized water-cooled reactors (BWRs and PWRs) that would substitute or modify traditional zircaloy materials. The rate of corrosion of the SiC ceramics in hot vapor environment (up to 2200 degrees C) simulating emergency conditions of light water reactor (LWR) depends on many environmental factors such as pressure, temperature, viscosity, and surface quality. Using the paralinear oxidation theory developed for ceramics in the combustion reactor environment, we estimated the corrosion rate of SiC ceramics under the conditions representing a significant power excursion in a LWR. It was established that a significant time – at least 100 h – is required for a typical SiC braiding to significantly degrade even in the most aggressive vapor environment (with temperatures up to 2200 °C) which is possible in a LWR at emergency condition. This provides evidence in favor of using the SiC coatings/braidings for additional protection of nuclear reactor rods against off-normal material degradation during power excursions or LOCA incidents. Additionally, we discuss possibilities of using other silica based ceramics in order to find materials with even higher corrosion resistance than SiC. In particular, we found that zircon (ZrSiO4) is also a very promising material for nuclear applications. Thermodynamic and first-principles atomic-scale calculations provide evidence of zircon thermodynamic stability in aggressive environments at least up to 1535 degrees C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improvements, enhancements, and optimizations of COBRA-TF

The Reactor Dynamics and Fuel Management Group (RDFMG) at The Pennsylvania State University (PSU) has become active in the Consortium for Advanced Simulation of Light Water Reactors (CASL) program by delivering, supporting, and further developing CTF, the PSU version of the Coolant Boiling in Rod Arrays - Two Fluids (COBRA-TF) Thermal/Hydraulic (T/H), sub-channel program. New development work on CTF was primarily geared towards decreasing the execution time of the code so that it may eventually be used for performing pin-by-pin, full-core simulations. Great gains have been made through targeting sections of source code for optimization. For example, wall clock time has been reduced for a one-assembly, three-dimensional model, containing {approx}9,400 mesh cells, from 9.2 min to 1 min. A further improvement has been reduction in code memory usage, which was previously prohibitive for large models. In conjunction with the run time speedups, this has enabled the simulation of a refined quarter-core model ({approx}460,000 mesh cells), which saw a reduction in memory usage from over 130 GB to less than 3 GB. In addition to the optimization work, RDFMG has also created a preprocessor utility for the fast and less error-prone generation of CTF input decks. Furthermore, basic post-processing capabilities have been implemented by creating a CTF subroutine for producing Visualization Tool-Kit (VTK) files that output mesh data and associated simulation results. These VTK files can be opened with visualization software. (authors)

97 MATHEMATICS AND COMPUTING↗

CTF Validation and Verification: Version 4.3

Coolant-Boiling in Rod Arrays- Two Fluids (COBRA-TF) is a thermal/hydraulic (T/H) simulation code designed for light water reactor (LWR) analysis. It uses a two-fluid, three-field (i.e., fluid film, fluid drops, and vapor) modeling approach. Both subchannel and 3D Cartesian forms of nine conservation equations are available for LWR modeling. The code was originally developed by Pacific Northwest Laboratory in 1980 and has been used and modified by several institutions over the last several decades. COBRA-TF is also used at the Pennsylvania State University (PSU) by the Reactor Dynamics and Fuel Modeling Group (RDFMG) and has been improved, updated, and subsequently became the CTF. One part of the improvement process includes validating the methods in CTF. This document seeks to provide a certain level of certainty and confidence in the predictive capabilities of the code for the scenarios it was designed to model—rod bundle geometries with operating conditions that are representative of prototypical pressurized water reactor (PWR)s and boiling water reactor (BWR)s in both normal and accident conditions. This is done by modeling a variety of experiments that simulate these scenarios and then presenting a qualitative and quantitative analysis of the results that demonstrates the accuracy to which CTF is capable of capturing specific quantities of interest.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Status Report on Design of In-situ Thermomechanical Testing at LANSCE

Nuclear fuel encounters severe thermomechanical environments in which its mechanical response is determined by its microstructure, temperature and stress level histories. Simulating the response of such microstructures is crucial for predicting both performance and transient fuel mechanical responses and experimental verification of such predictions is therefore of great interest. While most of the deformation in a nuclear fuel rod occurs in the cladding, deformation of the fuel itself is still of interest with deformation mechanisms at operating temperature and above including creep, swelling, cracking as well as pellet-clad interaction. Characterization of these properties and understanding of the underlying deformation phenomena at operating or excursion temperatures is therefore of great importance for development and ultimately licensing of improved and novel nuclear fuel forms. Diffraction techniques offer unique insight on the atomistic (e.g. crystal structure) and microstructure (e.g. phase transformations, texture, defects) length scales and have a long history of providing unique data to inform relevant deformation models that enable the required predictive capabilities. For example, dislocations lead to diffraction peak broadening that can be characterized to estimate the dislocation density and study the role of dislocations on the deformation while measuring lattice strains allows to studie load sharing in two phase materials. In this report the requirements for a sample environment for high temperature deformation of nuclear fuels are defined. The HIPPO neutron time-of-flight diffractometer at LANSCE will host this sample environment and is also described. This instrument covers diffraction angles from 140° to 40° and is also equipped with an event-mode neutron imaging detector system, enabling energy-resolved neutron imaging in parallel with the diffraction that could measure sample temperature from Doppler broadening of neutron absorption resonances or measure pore densities from changes in the attenuation. Designs of devices to characterize thermomechanical properties of nuclear fuel without diffraction are also considered to guide the design. While this report is focused on applications for nuclear fuels, the device can also characterize cladding, moderator or structural materials and therefore contribute to other fields of research and development for advanced reactors. The temperatures planned to be reached are above 2000℃, thus enabling characterization of LWR reactor fuels under accident scenarios but also reaching temperatures of fuels developed for nuclear thermal propulsion and providing opportunities to characterize those. In conjunction with the energy-resolved neutron imaging detector, this setup would allow to measure neutron cross-sections at high temperatures, filling a gap towards development of reactors operating at high temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Metal Fuel Casting Simulation (Annual Report)

Continuing work to develop the capability to simulate metallic fuel fabrication at Idaho National Laboratory (INL) is presented in this report. Simulations using the Truchas code developed at LANL and the commercial software package FLOW3D were used to evaluate the capabilities necessary for modeling mold filling and solidification of the bench scale caster (BSC). The results suggest that surface tension and the pressure effects of the argon in the mold must both be included in the simulation to obtain results that are qualitatively similar to the experimentally observed rod size and morphology. Effects of viscosity of the liquid metal seem to be relatively unimportant. The possibility of flow of partially solidified material is examined, and may be important for the flow conditions in the BSC. A more general discussion of software requirements is included for casting processes that are suitable for metallic fuel rods. A comparison of current capabilities of Truchas and FLOW3D is presented. Neither of the two codes has all the capabilities needed, and future work will probably use both software packages. A performance and scaling evaluation of FLOW3D indicates that adequate performance can be obtained for this project using multiprocessor hardware.

1.02.02.02↗

Resonance self-shielding methodology in MPACT

The resonance self-shielding methods of the neutron transport code Michigan Parallel Characteristics based Transport (MPACT) are described in this paper. Two resonance-integral table based methods are utilized to resolve the resonance self-shielding effect. The subgroup method is a mature approach used in MPACT as the basic functionality for the resonance calculation. Another new iterative method, named the embedded self-shielding method is also implemented in MPACT. Comparisons of the two methods as well as their numerical verifications are presented. The results show that MPACT is capable of modeling the resonance self-shielding in a variety of PWR benchmarking cases, including difficult fuel lattice cases with poison, control rods or mixed gadolinia fuel rods. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

CTF 4.0 Validation and Verification

Coolant-Boiling in Rod Arrays- Two Fluids (COBRA-TF) is a Thermal/Hydraulic (T/H) simulation code designed for Light Water Reactor (LWR) analysis. It uses a two-fluid, three-field (i.e. fluid film, fluid drops, and vapor) modeling approach. Both sub-channel and 3D Cartesian forms of nine conservation equations are available for LWR modeling. The code was originally developed by Pacific Northwest Laboratory in 1980 and has been used and modified by several institutions over the last several decades. COBRA-TF is also used at the Pennsylvania State University (PSU) by the Reactor Dynamics and Fuel Modeling Group (RDFMG) and has been improved, updated, and subsequently became the PSU RDFMG version of COBRA-TF (CTF). One part of the improvement process includes validating the methods in CTF. This document seeks to provide a certain level of certainty and confidence in the predictive capabilities of the code for the scenarios it was designed to model—rod bundle geometries with operating conditions that are representative of prototypical Pressurized Water Reactor (PWR)s and Boiling Water Reactor (BWR)s in both normal and accident conditions. This is done by modeling a variety of experiments that simulate these scenarios and then presenting a qualitative and quantitative analysis of the results that demonstrates the accuracy to which CTF is capable of capturing specific quantities of interest.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

CTF Validation and Verification (V.4.2)

Coolant-Boiling in Rod Arrays- Two Fluids (COBRA-TF) is a thermal/hydraulic (T/H) simulation code designed for Light Water Reactor (LWR) analysis. It uses a two-fluid, three-field (i.e. fluid film, fluid drops, and vapor) modeling approach. Both sub-channel and 3D Cartesian forms of nine conservation equations are available for LWR modeling. The code was originally developed by Pacific Northwest Laboratory in 1980 and has been used and modified by several institutions over the last several decades. COBRA-TF is also used at the Pennsylvania State University (PSU) by the Reactor Dynamics and Fuel Modeling Group (RDFMG) and has been improved, updated, and subsequently became the PSU RDFMG version of COBRA-TF (CTF). One part of the improvement process includes validating the methods in CTF. This document seeks to provide a certain level of certainty and confidence in the predictive capabilities of the code for the scenarios it was designed to model-rod bundle geometries with operating conditions that are representative of prototypical Pressurized Water Reactor (PWR)s and Boiling Water Reactor (BWR)s in both normal and accident conditions. This is done by modeling a variety of experiments that simulate these scenarios and then presenting a qualitative and quantitative analysis of the results that demonstrates the accuracy to which CTF is capable of capturing specific quantities of interest.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Uncertainty and Sensitivity Analysis of TREAT Transient Test no. 15

The U.S. Department of Energy (DOE) is preparing for the resumption of transient testing using the Transient Reactor Test Facility (TREAT) located at the Idaho National Laboratory (INL). In order to support the analysis of TREAT operation and experiment planning, the MAMMOTH reactor physics team has recently begun development of uncertainty and sensitivity analysis for the TREAT core simulated via MAMMOTH. MAMMOTH is a high-fidelity three-dimensional transient multi-physics code developed at INL under the DOE-NE Advanced Modeling and Simulation program (NEAMS). This research is part of the development presenting some initial uncertainty and sensitivity analysis of TREAT Transient Test no. 15. In this summary, we employ the Sobol sampling strategy implemented in RAVEN to efficiently perform the sensitivity and uncertainty analysis. The idea is using Sobol functional decomposition with generalized polynomial chaos (gPC) expansions to estimate the responses of interest. The gPC coefficients are then computed via the sparse grid spectral projection method. In addition, this strategy includes evaluation of the second or higher order sensitivity indices, allowing the study of interactions between several input variables. The principal focus of this analysis is to quantify the uncertainties in the total power and maximum fuel temperatures with respect to uncertainties in the initial transient conditions, such as rated power, fuel temperature, graphite fuel density and control rod boron concentration. In addition, both the first order and second order time-dependent sensitivity indices are computed and analyzed. The results show that the interactions between initial control rod boron concentration and the rated power will contribute at most 1% to the total uncertainty of the power peak.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Analysis of the IFA-432, IFA-597, and IFA-597 MOX Fuel Performance Experiments by FRAPCON-3.4

Validation of advanced nuclear fuel modeling tools requires careful comparison with reliable experimental benchmark data. A comparison to industry-accepted codes, that are well characterized, and regulatory codes is also a useful evaluation tool. In this report, an independent validation of the FRAPCON-3.4 fuel performance code is conducted with respect to three experimental benchmarks, IFA-432, IFA-597, and IFA-597mox. FRAPCON was found to most accurately model the mox rods, to within 2% of the experimental data, depending on the simulation parameters. The IFA-432 and IFA-597 rods were modeled with FRAPCON predicting centerline temperatures different, on average, by 21 percent.

Phillippe, Aaron M.↗

Enhanced LWR High Burnup Transient Simulation Capabilities to Support AOO Margin Identification

As part of ongoing efforts to support the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program’s development of a fuel fragmentation, relocation, and dispersal (FFRD) screening methodology, a number of improvements are required for the NEAMS core simulation capabilities, namely the Virtual Environment for Reactor Applications (VERA). Three areas of improvement were identified in VERA which are important for continued development and application of the FFRD screening methodology. First, the FFRD screening methodology will soon be extended to boiling water reactors (BWRs), requiring development and validation of the VERA BWR capabilities. Second, the screening methodology occasionally requires that VERA be used to simulate a transient in addition to nominal operations. Thus, improvements to both accuracy and performance of the VERA transient capabilities are necessary. Third, the VERAOneWay component of VERA is used to develop BISON fuel performance inputs using the rod-by-rod histories calculated by VERA. Prior use of VERAOneWay exposed significant accuracy, robustness, and performance issues with VERAOneWay; these must be addressed for it to be an effective tool in the NEAMS FFRD methodology. This report documents the efforts in FY23 in each of these three areas to enable successful use of VERA and VERAOneWay for FFRD calculations in FY24 and following years.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Separate-Effects Validation Experiments for Models of Fracture in Ceramic Nuclear Fuel

A number of advances have recently been made in modeling fracture initiation and propagation in ceramic light water reactor (LWR) fuel. These include the use of techniques such as peridynamics, the extended finite element method (XFEM), the discrete element method (DEM), and phase field fracture. Improved predictions of fracture in LWR fuel can benefit fuel performance simulations in a number of ways, with important implications for radial relocation, pellet-cladding mechanical interactions, and fragmentation during accident conditions. Although these modeling approaches appear promising, to-date most of their applications have been to fresh fuel. A major limitation in applying these approaches with confidence to a wider variety of conditions, such as fragmentation of high-burnup fuel, is that there is very limited data that can be directly used to validate the results of these fracture models. While fracture patterns are available from cross-sections of numerous irradiated fuel rods, the fuel rods have typically been subjected to complex irradiation histories. To validate models of fracture propagation, focused experiments that give snapshots of the initiation and propagation of fracture under well characterized prototypical reactor conditions are needed. Under a multi-institutional U.S. Department of Energy Integrated Research Project (IRP), three separate-effects validation experiments are underway to provide information on the propagation of cracks in LWR fuel under controlled conditions. The primary challenge in developing such an experiment is in providing conditions that result in a radial temperature distribution that is prototypical of LWR in-reactor conditions. Two out-of-reactor experiments are being planned that employ very different approaches to achieve such a temperature distribution. The first of these achieves this by employing a combination of inductive and resistive electrical heating to generate volumetric heating. The second experiment involves slowly heating a pellet in a metal rod to a high temperature, and then quenching that rod in a cold bath. The quenching process generates a temperature profile approximating that in an LWR fuel rod for a moment, but has a very different temperature history from the LWR. Finally, an experiment is being planned for the Idaho National Laboratory TREAT reactor that will use nuclear fission as a heat source, and which will employ a metal heat sink to replicate the thermal conditions provided by coolant in an LWR. These experiments all have their advantages and drawbacks, with varying levels of ability to reproduce actual LWR conditions and varying ability to use instruments to monitor quantities of interest over the course of the experiment that can be used to validate fracture models. For that reason, these different experimental approaches are complimentary to each other, and the combined results are expected to significantly improve confidence in the ability of computational models to simulate fracture in ceramic nuclear fuel.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Evaluation of accuracy of calculations of VVER-1000 core states with incomplete covering of fuel by the absorber

An additional verification of bundled software (BS) SAPFIR-95 and amp;RC [1] and code KORSAR/GP [2] was performed. Both software products were developed in A.P. Alexandrov NITI and certified by ROSTEKHNADZOR of RF for numeric simulation of stationary, transitional and emergency conditions of VVER reactors. A benchmark model for neutronics calculations was created within the limits of this work. The cold subcritical state of VVER - 1000 reactor stationary fuelling was simulated on the basis of FA with an increased height of the fuel column (TVS-2M) considering detailed presentation of radial and front neutron reflectors. A case of passing of pure condensate slug through the core in initially deep subcritical state during start of the first RCP set after refueling was considered as an examined condition of reactor operation. A relatively small size of the slug, its spatial position near the reflectors (lower and lateral), as well as failure of the inserted control rods of the control and protection system (CPS CR) to reach the lower limit of the fuel column stipulate for methodical complexity of a correct calculation of the neutron multiplication constant (K{sub eff}) using engineering codes. Code RC was used as a test program in the process of reactor calculated 3-D modeling. Code MCNP5 [3] was used as the precision program, which solves the equation of neutrons transfer by Monte-Carlo method and which was developed in the US (Los-Alamos). As a result of comparative calculations dependency of K{sub eff} on two parameters was evaluated - boron acid concentration (Cb) and CPS CR position. Reactivity effect was evaluated, which is implemented as a result of failure of all CPS control rods to reach the lower fuel limit calculated using the engineering codes mentioned above. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Effects of transient fission gas release on rod balloon burst behavior during a loss-of-coolant accident

The US nuclear energy industry is investigating strategies to increase the reactor operating cycle to 24 months, which would result in rod average burnups exceeding the current limit of 62 GWd/tU. To support this goal, multiphysics simulations tools and methodologies are being developed to predict the effects of this change during transient events such as loss-of-coolant accidents (LOCAs). In this work, two cladding burst correlations were used to predict cladding failure. Here, these were coupled with three transient fission gas release (tFGR) models and were implemented in the BISON fuel performance code to quantify any changes in cladding burst behavior during a large-break LOCA. First, a simple linear model was used to perform a sensitivity analysis of a single fuel rod. Second, a tFGR model available in BISON was applied to 281 fuel rods throughout the core. The third model examined was an empirical correlation based on data from the literature.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Multiphysics Simulation of the NASA SIRIUS-CAL Fuel Experiment in the Transient Test Reactor Using Griffin

After approximately 50 years, NASA is restarting efforts to develop nuclear thermal propulsion (NTP) for interplanetary missions. Building upon nuclear engine tests performed from the late 1950s to the early 1970s, the present research and testing focuses on advanced materials and fabrication methods. A number of transient tests have been performed to evaluate materials performance under high-temperature, high-flux conditions, with several more experiments in the pipeline for future testing. The measured data obtained from those tests are being used to validate the Griffin reactor multiphysics code for this particular type of application. Griffin was developed at Idaho National Laboratory (INL) using the MOOSE framework. This article describes the simulation results of the SIRIUS-CAL calibration experiment in the Transient Reactor Test Facility (TREAT). SIRIUS-CAL was the first transient test conducted on NASA fuels, and although the test was performed with a relatively low core peak power, the test specimen survived a temperature exceeding 900 K. Griffin simulations of the experiment successfully matched the reactor’s power transient after calibrating the initial control rod position to match the initial reactor period. The thermal-hydraulics model largely matches the time-dependent response of a thermocouple located within the experiment specimen to within the uncertainty estimate. However, the uncertainty range is significant and must be reduced in the future.

33 ADVANCED PROPULSION SYSTEMS↗

Investigation of Passive Gamma Spectroscopy to Verify Spent Nuclear Fuel Content

Measurement of passive gamma rays emitted by the decay of radioactive isotopes is a widely used and fundamental technique to verify and determine characteristics of nuclear materials. Several initiatives are currently under way to investigate the use of advanced nondestructive assay methods for application to independently measure the fissile material and plutonium content in spent nuclear fuel. Although no single technique is capable of accurately measuring the actinide inventory, the integration of multiple measures has the potential to dramatically improve nondestructive analysis capability. These methods are likely to involve the use of high-resolution gamma detectors with the resolving power necessary for isotopic identification. Recent high-resolution gamma-ray spectroscopy measurements of spent nuclear fuel rod segments performed at Oak Ridge National Laboratory provided an important opportunity to analyze and identify the dominant and minor gamma-ray signatures that can be acquired using conventional HPGe detectors. The spent fuel source and detector spectra were simulated to identify potential low-intensity gamma signatures in the fuel that could be observed with modest improvements in detector capability. The measurements represent important experimental benchmarks for code and detector model simulations that will be needed to better determine advance detector design requirements for spent fuel measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗